Search Documents

By Hayes J. A

The satisfactory ventilation of an extensive coal mine is a subject which requires continual attention from all concerned.It must be remembered that a colliery contains many miles of workings, extending in all directions and throughout which noxious gases may be given off either naturally or by oxidation of the coal; fumes from explosives will be produced, dust will be gathered and carried in suspension, and water will be evaporated, producing a high humidity. Hence a considerable quantity of air in movement must be available to provide sufficient oxygen for men and horses, as well as to dilute and sweep away impurities, and maintain a tolerable degree of coolness.To maintain these conditions a modern colliery is divided up from the main ventilation shafts or adits (as the case may be) into a system of main airways, and in the working districts is further subdivided into district splits. To initiate the air movement, large centrifugal fans with a displacement capacity of up to 400,000 cu. ft. of air per minute are installed, generally in drifts off the upcast shaft, or adit, and at the return end of the ventilating circuit. These fans are thus exhausting fans and by producing a region of low density bring the heavier air at the other extremity of the circuit into movement to correct the difference in density, so far as it is not prevented by the frictional resistance of the airways. A flow of air is thus established, and it is obvious that to enable this volume of air to be as great as possible, the frictional resistance of the mine airways should be maintained at the lowest practicable figure. To this end, main airways should be as large as possible, have sides as smooth as practicable, and be straight, any necessary bends being of large radius.REQUIREMENTS OF THE VENTILATION SYSTEMThe New South Wales Coal Mines Regulation Act contains stringent provisions on requirements of the ventilation system. The main points are expressed in the following extracts:"In every mine which is in operation, unless a certificate of exemption from compliance with this rule has been granted by the Minister, whether any person employed therein shall be...

Jan 1, 1947

By Butler I. K, Nicholson P. M

There are four main types of base metal and gold mineralisation recognised in the central Pine Creek Geosyncline. These are stratiform, polymetallic veins, stockwork/concordant gold-quartz veins and unconformity related uranium-gold-platinoid mineralisation. The stratigraphy of the central Palaeoproterozoic Pine Creek Geosyncline has been simplified into three groups comprising the Batchelor, Frances Creek and Finniss River Groups in ascending order. Stratiform mineralisation occurs within the Frances Creek Group. The earliest mineralisation is found adjacent to circular faults ringing basement highs. Higher in the stratigraphy, stratiform mineralisation is often associated with zones of high compression in the vicinity of basement highs. A synsedimentary-diagenetic origin for stratiform mineralisation is proposed. Polymetallic vein mineralisation occurs within the Frances Creek and Finniss River Groups. Its composition changes systematically through the stratigraphy similar to the stratiform mineralisation. The mineralisation is structurally controlled and usually occurs in the vicinity of basement highs. Stockwork-concordant gold-quartz vein mineralisation is hosted by the upper Frances Creek and Finniss River Groups. It occurs within compressional zones and along the Pine Creek Structure corridor around, above and particularly between basement highs. Mineable reserves occur in thick continuous semi concordant quartz-sulphide veins and/or stockworks. Unconformity related uranium-gold-platinoid mineralisation shows a close spatial relationship with the Palaeoproterozoic/Mesoproterozoic unconformity. The mineralisation is localised by structures formed during Mesoproterozoic deposition and is commonly adjacent to Archaean basement or its remobilised equivalents. The type of mineralisation (stratifom/polymetallic vein) is a reflection of local stress regimes, structure and physio-chemical conditions. An initial phase of stratiform mineralisation is postulated to have occurred with the first significant marine transgression in a tensional regime. A second phase occurred later during a compressive regime. "Ihermochemical sulphate reduction of mineralising fluids by hydrocarbons is invoked as the precipitation mechanism for the polymetallic vein type of mineralisation. Hydrocarbon generation is postulated to have occurred within the Frances Creek Group, in many places contemporaneously with the movement of mineralising fluids and basin compression. Polymetallic veins formed from the interaction of mineralising fluids and hydrocarbons which were trapped in suitable structures. An abundant, continuing supply of hydrocarbons was necessary to form significant deposits. Where these conditions were not net, the mineralising fluids largely continued their ascent to the near surface environment to form stratiform deposits. The stockwork/concordant gold-quartz vein mineralisation is a later event and occurred during the relaxation of compressional defonnation after deposition of the 1-inniss River Group.

Jan 1, 1994

By E Giles

Pike River Coal Limited (PRCL) is opening a new underground coal mine in the Paparoa Ranges north-east of Greymouth. To access the coal reserves, PRCL have had to build a 13 km access road through regrowth and virgin forest, and appointed McConnell Dowell Constructors Limited, with URS New Zealand Limited as their consulting engineers, to construct the final access link: a 2.3 km long, 5.5 m wide and 4.5 m high incline tunnel. This paper discusses the logistical issues of construction in an isolated pristine forest in mountain land and how they were addressed. It provides an overview of the 90 per cent complete tunnel and how challenging rock conditions have been mastered. It outlines briefly the remaining work which is construction of pit bottom workings where the mine infrastructure will be housed and construction of a 110 m deep, 4.0 m diameter, vertical ventilation shaft.

Jan 1, 2008

By M Behrens, A McPhee, B D. Hegan

This paper describes the design and construction of twin 400 m long road tunnels as part of the Northern Motorway Extension Project in Auckland, New Zealand. Construction of the tunnel civil works is now completed and installation of mechanical and electrical systems is well underway. The tunnels are expected to be open for traffic at the end of 2008. The paper will address the design aspects of the project including: tunnel alignment and cross-section, geotechnical conditions and rock support, waterproofing and concrete lining and fire and life safety. The paper will cover the bored tunnel section, the cut-and-cover tunnel section, cross passages and portal structures. The design brief included a requirement for the tunnels to be a gateway to Auckland and this required particular attention to be given to the visual appearance of the finished tunnel structure. The final arrangement of the portal structures and a requirement for recesses in the concrete lining for emergency cabinets, deluge pipework and cable runs, reflects these requirements. The tunnels were excavated by a roadheader and road planer using a heading and bench. Initial support was provided by a combination of lattice girders, cement grouted rock bolts and steel fibre reinforced shotcrete. The permanent lining consisted of installation of a drainage geotextile and waterproof membrane, followed by cast in situ unreinforced concrete. Each portal consists of a cut-and-cover section. This paper describes the tunnel construction methods, including the particular requirements for safety, the environment and community relations. The tunnel is fitted with a compartmentalised deluge system for fire fighting purposes. The tunnel control centre is incorporated into the control centre for Auckland Harbour Bridge, some 30 km from the tunnel location.

Jan 1, 2008

By Marshall K. I

THE problem of satisfactorily eliminating the fumes and dust which are unavoidably produced in various metallurgical and manufacturing industries is one which has received considerable attention in the past, and has been the subject of much investigation and research. The solution of this problem was urgently desired for two reasons, the principal one being the fact that a considerable percentage of the total process losses in many industries was represented by the commercial values of the fumes and dust that escaped from the stack.The other reason is that, in some instances, the emission of the matter is regarded as objectionable. Various methods have been designed with a view to solving the problem thus presented, and the latest development that has beendesigned is the process of electrostatic precipitation. Continued investigational and developmental work with this process has already demonstrated its applicability to many industries, and new uses to which the process can be put are being opened up. Its use is already widespread, and the economic success that has attended its application in most instances would indicate that its use will become more general in the future.It has proved its ability to treat gases over wide ranges of temperature, and has successfully handled various types of fumes whose chemical characteristics differ very considerably. In many processes it has now come to be regarded as standard equipment.HISTORY OF ELECTRICAL PRECIPITATIONThe first recorded observations on the influence of an electrified insulated wire on gases containing solid particles in suspension was made as early as 1824 by Hohlfeld, in Leipzig. He found that, if he electrified a wire hung in a bottle filled with smoke, the smoke cleared rapidly, and a deposit formed on the sides and bottom of the bottle.

Jan 1, 1923

By T Ma, F T. Suorineni, Q He, J Oh

Directional hydraulic fracturing was invented by Polish experts and was first applied in coal mining to prevent hard roof rock bursts. Based on its successful application in coal mining, directional hydraulic fracturing has the potential to reorientate the hydraulic fracture trajectory. Recently, this technique has been introduced into cave mining for the purpose of lowering breakdown pressure. The hydraulic fracture is much easier to initiate with the assistance of an initial notch. No systematic theoretical or experimental studies have been carried out to investigate the influencing factors in the hydraulic fracture reorientation process. In this paper, the numerical modelling software Realistic Failure Process Analysis3D (RFPA3D) – Flow Version is used to study the influence of the in situ stress condition and rock mass heterogeneity on directional hydraulic fracturing in brittle heterogeneous rock masses. Firstly, the reliability of RFPA3D in simulating hydraulic fracturing is validated by comparing its results with experimental results and the simulation results from the extended finite element method. The hydraulic fracture trajectory is then observed in a three-dimensional stress environment. The results indicate that for the in situ stress condition, when the borehole lies in the ?2–?3 plane, only the difference between ?2 and ?3 has an important influence on hydraulic fracture reorientation. Furthermore, rock mass heterogeneity is a key factor that must be accounted for when fracture reorientation is required.CITATION:He, Q, Suorineni, F T, Ma, T and Oh, J, 2016. Modelling directional hydraulic fractures in heterogeneous rock masses, in Proceedings Seventh International Conference and Exhibition on Mass Mining (MassMin 2016), pp 369–384 (The Australasian Institute of Mining and Metallurgy: Melbourne).

May 9, 2016

By Jarvis ST

Colliery spoil is the major constituent of colliery spoil 'rockpaste' which has been used to infill abandoned limestone mines in the West Midlands of England since the early-1980s. The other constituents of rockpasle are pulverised fuel ash, lime and water. A key property of the rockpaste is its ability to flow within the mine workings over considerable distances before setting. This paper describes the work carried out to identify suitable sites as sources of colliery spoil for making rockpaste and goes onto consider the flow properties of the material and the monitoring methods used on-site. A full-scale trial comprising mulling a 6600 nt' section of an abandoned mine was conducted prior to the mulling of the Littleton Street Mine which had a volume of about 500 000 m'. As well as describing the methods used for monitoring the movement of rockpaste material, a description is also given of a dip-meter developed specifically for the purpose of measuring the level of paste in the mine. This paper shows how a colliery spoil based paste has been successfully rued for infilling abandoned mine workings. The monitoring systems developed for use in the two case studies presented in this paper are now being used extensively for infilling other abandoned mine workings. To-date over I I mines with a total volume exceeding two million cubic metres have been backfilled.

Jan 1, 1998

At Pasminco Mining's South concentrator. which was commissioned in 1952. an expansion. modernisation and efficiency improvement program commenced in 1986 with a coarse ore stockpile and grinding circuit expansion. the replacement of small flotation cells and the upgrading of reagent mixing and metering equipment. The program continued with the installation of a TDC 3000 based process control system (1988) and concentrate thickeners (1990). By mid-1991 a further grinding expansion and the installation of zinc flotation feed regrind ball mills and zinc recleaner column cells will be complete. leaving the use of ceramic disc fillers and development of process control strategies as probably the remaining major avenues for improved process efficiency at present.

Jan 1, 1991

Brand se Baai, on the North-Western Cape Coastline of Southern Africa, is the site of the Namakwa Sands Limited Heavy Mineral Sands Mining Operation. The mine is a 14 000 000 tonnes per annum open-cast strip-style mining operation using truck and excavators to mine the sand. The orebody consists of relatively unconsolidated sands reworked by fluvial, marine and aeolian mechanisms. The total orebody includes three primary ore types, namely the Red Aeolian Sands, the Dorbank (a hardcap layer) and the Orange Feldspathic Sands, which forms the bulk of the resource. Mine planning and scheduling is done using a 50 m + 50 m variable bench height system with three primary bench heights. The Aeolian and Dorbank each have a bench that varies with their thickness of up to a maximum eight metres and the Orange feldspathic sand, a standard bench height of eight metres. For a number of years Namakwa Sands used a complex 2D, Datamine Based, macro system to perform the resource evaluation and mine design. As the mining operations expanded it became clear that a complete system redesign was required to cope with the increasing operational pressures coming to bear on the old system. The biggest challenges facing any replacement system are the sheer scale of the mining operation (16 km long and 7 km wide resulting in a minimum of 30 000 individual 50 m + 50 m mining blocks), the size of the geological data files (up to one gigabyte) and representing the benching system accurately (as the benches follow the topography and are not horizontal). In addition to these large-scale issues, the ability to run multiple mine design scenarios was required, an aspect which the old system was unable to perform adequately. Based upon these primary difficulties, a new business process was developed which required a complete rethink of the mine design methodology as well as the creation of a new system to deplete the resource model, produce monthly reconciliation evaluations and create a ultimate pit limit based on the operations mining cost model. Using a system based on the Earthworks Mine2-4D Mine Design and Scheduling System (with its mine design and scheduling specific tools), as well as a small, customised program, massive time-savings have been made. It is now possible to run several life of mine scenarios in the same timeframe that a single life of mine run took under the old system. This paper will present the methodology and business decisions behind the new Namakwa Sands system, and detail the restructuring and development used to deal with the large data set sizes and long processing times inherent in the old system. Future enhancements to the system that will make it more generically applicable to open-cast mining scenarios will also be dealt with.

Jan 1, 2003

To help meet the challenge of mine finding at the start of the 21st century, the exploration geophysicist will have at his command a powerful range of tools, some new, some improved, and some which already exist today but are as yet little used. Remote sensing, using satellite and aircraft-based multi-spectral scanners, will provide the means for routinely mapping the surface distribution of certain carbonate rocks, clay and ferrous alteration minerals, based on the analysis of solar reflectance spectra. Time and emission-spectral resolved laser-induced fluorescence will likewise map the distribution of certain ore and pathfinder minerals, as well as certain skarn zones, all potentially related to ore deposits. The GPS (Global Positioning System), based on 18 orbitting satellites, will provide a universal, three dimensional, all weather navigation system which will completely supplant all existing aerial navigation systems, and greatly facilitate aerial surveying and automated processing and presentation of the data. Aeromagnetic gradiometer measurements will provide higher geometric resolution which will yield better definition of individual geological units. Multi-method ground geophysical surveys will be greatly expedited through the use of portable microcomputer-based, multi-sensor instruments. These instruments will interface with other intelligent devices for automated processing, presentation and interpretation of the ground field data. Borehole geophysics will come into more general use, both for at-hole measurements, especially using active nuclear techniques for grade determination, and for remote detection using a variety of electrical, magnetic, seismic and other methods.

Jan 1, 1986

By P A. Grossman, J H. Rubinstein, M Brazil, K G. Sirinanda

To date, the scheduling and access design of an underground mine have only been considered as two separate optimisation problems. First, access to the mine is designed and then the scheduling is completed. One drawback of this approach is that the costs of access construction fail to be reflected in the net present value (NPV) calculation. In this paper, designing the access and scheduling its construction are formulated as a single optimisation problem.The underground mine access construction process can be classified according to the number of faces being developed concurrently. An underground mine with a single decline branching at a junction point into two declines is considered. After construction reaches the junction, the two faces of the decline can be constructed sequentially or concurrently.This paper proposes an efficient algorithm for optimally locating a junction point to maximise the NPV where two faces are being developed concurrently. The NPV is defined by taking the locations of orebodies and their values, decline construction costs, decline development rate and discount rate into account. The variation of the NPV and the optimal locations of the junction point for one and two concurrent development faces for a range of discount rates are discussed and compared. The proposed algorithm is applied in a simulated case study based on hypothetical values for an underground mine.CITATION:Sirinanda, K G, Brazil, M, Grossman, P A, Rubinstein, J H and Thomas, D A, 2014. Strategic underground mine access design to maximise the net present value, in Proceedings Orebody Modelling and Strategic Mine Planning Symposium 2014 , pp 235–242 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 24, 2014

By Cocks T

The 15-year long debate between the industry, Government and Aboriginal people about the rights and wrongs of Land Rights, the right of Aboriginal people to control development on their land and the relationship between the parties, has been long and often bitter. It has so far been a war of words and often the truth has been the first casualty. This paper looks at the debate and presents the perspective of Aboriginal people, as well as looking at how the industry and Aboriginal people can work together for everyone's benefit. It addresses such matters as: ò why Aboriginal people believe they have the right to control development on their land; ò the perception that Aboriginal people are anti-development; ò the perception that Aboriginal land is 'locked-up'; and ò how companies can negotiate with Aboriginal people.

Jan 1, 1994

By J A. Cowburn

The high intensity zone within the Jameson Cell is the downcomer. It is largely external and separated from the flotation tank. This, together with operation of the downcomer under vacuum, rather than at elevated pressure and the absence of moving parts, allows ready access to the high intensity zone for measurement and analysis. Experimentation was conducted allowing measurements of recovery for residence times of between 20 milliseconds and ten seconds within the downcomer of a Jameson Cell. The affect of aeration rate on the recovery of different particle sizes was also studied.

Jan 1, 2005

By N Davies, M J. Coward, P L. Hissey

Mount Isa Mines has four mining operations in Mt Isa with the X41 and Enterprise Mines producing copper and the Lead Mine and George Fisher producing lead zinc and silver. Each stream contributes ore to their respective concentrator at a feed rate and therefore metal ratio set out by the monthly schedule. Mine Planning and scheduling lead to a sales and operating plan (S&OP) and revenue projections which ultimately derives actual revenue /tonne and therefore cost/tonne. At Mount Isa, both the copper and lead/zinc streams produce ore from relatively new operations to be blended with material from more mature operations. It is critical to accurately predict the metal contribution from each operation in order to gauge the relative performance of each mine. Development mining ore contributions are estimated and reconciled, as are stope and bench sources. Performance is continually measured and assessed during extraction and grade adjustments are made to account for underbreak, overbreak and design modifications. It is critical to not understate or overstate the contribution from one operation relative to the other as this can produce a false picture of operational performance. Identifying process improvements are key to improving the business overall. Ore from the lead stream passes 17 measurement stations and two midstream reconciliation points before delivery to the heavy media plant (HMP), where the metallurgical circuit begins. From this point two concentrates are produced. A zinc concentrate for treatment off site and a lead concentrate for further on site processing. The lead smelter takes 100 per cent of Isa concentrates as well as a contribution from BHP-BillitonÆs Cannington Mine.

Jan 1, 2002

By Caress ME, Knight MD

The eruption 75,000 y ago of the Younger Toba Tuff ignimbrite and associated ash-fall ranks as the greatest known volcanic event of the past million years. The ignimbrite is known to cover 21,000 km2 (it may extend farther under alluvium of the coastal plain) and forms a low-angle depositional shield centered on the Lake Toba caldera. The ignimbrite is largely nonwelded and shows systematic outward decreases in lithic and crystal contents and clast sizes. Coarse lithic lag breccias that occur at places 85 km apart point to two or more vents on a fissure having this length. The extensive associated ash-fall traceable as far as Malaysia and India is evidently a co-ignimbrite ash but could have a phreatomag-matic component. The Lake Toba caldera measures95 x 35 km and is >1 kn deep. It is not a single caldera but comprises several contiguous depressions and grabens diversified by two re-surgent domes. Earlier parts of the caldera are related to at least two earlier ignimbrites including the Older Toba Tuff dated by Chesner at 0.5 Ma. The caldera is elongated parallel to, and is only 25 km from, the great Sumatra strike-slip fault, and it can be considered almost certain that the caldera is in part a kind of pull-apart structure. The ignimbrites are very crystal-rich. There is no reason to think basaltic magma was involved in their emplacement. Together with ash-falls they have a total volume of several thousand cubic kilometers. They can be categorized as originating from partially crystallized granitic magmas that erupted because tectonic pull-apart occurred several times across the pluton. Small rhyolitic lava domes on fault-lines comprise the youngest volcanic products.

Jan 1, 1990

By Bawden WF, Paynter JT

This investigation involves laboratory testing and stability analysis of paste fill at the Golden Giant Mine. Site-cast samples are tested in unconfined, confined, and consolidated-undrained triaxial compression. Pore pressures during shear and consolidation characteristics are measured to determine both drained and undrained shear strength parameters and assess the potential for undrained loading. Liquefaction potential is also considered. A limit equilibrium solution is used to obtain factors of safety against failure of the fill during mining of adjacent stopcs

Jan 1, 1998

By N Donnellan

The Palaeoproterozoic Warramunga Formation is notable as the host to the enigmatic, so-called 'Tennant Creek style' mineralisation. These polymetallic (but mainly Au-Cu-Bi) ore deposits typically have a close spatial association with massive ironstone bodies, and frequently also with banded ironstone, known locally as 'haematite shale'. The Warramunga Formation is a polydeformed, turbiditic succession. Partial, or complete Bouma sequences variously comprising lithic arenite, wacke, siltstone, and mudstone constitute a classic flysch sequence deposited as a proximal (sandstone lithofacies) to distal (siltstone lithofacies) fan association. The Warramunga Formation has a substantial component of volcanic detritus and has generally been attributed to an essentially contemporaneous volcanic provenance. However, lithostratigraphic revision (Donnellan, Hussey and Morrison, in press) apparently precludes outcropping volcanic rocks of the Tennant Creek Block, or indeed Inlier, as the source of detritus. Warramunga Formation geochemistry indicates rapid derivation from a fractionated, predominately felsic igneous source (Palaeoproterozoic upper crust) with a minimum of chemical weathering; together with an admixture of mafic material. Warramunga Formation geochemistry cannot, however, be reconciled with that of the Bemborough Formation, which is here taken to be representative of Flynn Subgroup felsic volcanic rocks. Similarly, the Warramunga Formation is geochemically distinct from Flynn Subgroup sedimentary rocks. Geochemistry of the banded ironstone is consistent with its interpretation as Dine-grained turbidites.

Jan 1, 1994

By DV Boger

Rheology is the science which deals with the deformation and flow of matter. Thus nccology is concerned with the flow of any material. The mining industry is concerned with digging things out of the ground, extracting the good stuff and throwing away the had stuff. In the upgrading processes associated with mining, is mineral processing, wet techniques are used where the primary material being handled is a particulate fluid, ie a suspension. After the processing operation, with the concentrates extracted, what is left behind generally is a wet material in suspension form, which may or may not contain reagents harmful to the environment. The amount of waste generated in any of the mining processes is large, in fact, the mining industry is the largest generator of solid waste in Australia. In order to minimise the waste generated within the industry it has become of interest to handle the particulate fluid wastes, or suspensions, at high concentrations, thus removing water and some of the reagents which may be harmful to the environment. The resultant highly concentrated suspension is a non-Newtonian hold Rheology deals with the flow of non-Newtonian fluids; therefore i combination of rheological understanding of high density suspensions. ill conjunction with an understanding of the environmental problems hero' faced by the mining industry, can and has led to improved methods of waste disposal in the industry, ie waste minimisation. This paper describes the progress that has been made in the development of dry disposal technology in the mining and minerals industry in Australia.

Jan 1, 1998

The performance of the Australian Mining Industry over the past 10 years using key indicators of production, revenue, aftertax return investment, together with key cost elements, market changes and ore reserves is briefly reviewed. The elements of competitiveness are discussed forthe industry and the effects of Government charges and policies relating to existing operations are outlined. There is a demonstrated need for improvements in competitiveness in direct and indirect costs and for improved access to resources for the mining industry to continue to grow and add to Australia's economic growth.

Jan 1, 1987

By B Clements, R Dunne, J Dioses, S Hart

In April 2003 plant upgrades in the æLow GradeÆ Cadia Hill circuit were undertaken in order to improve concentrate quality and metal recoveries from the flotation circuit. The major changes involved: circuit reconfiguration to allow all concentrates to be reground to less than 38 ¦m prior to final cleaning; increasing ball charge in the regrind mill to fully utilise all of the installed power; desliming of the cleaner scavenger concentrate to improve the circuit water balance; and the inclusion of a gravity concentrator in the regrind circuit to recover more free gold to bullion.Once the flotation circuit had stabilised under the new operating conditions concentrate launder modifications and increased froth crowding on the scavenger flotation cells permitted the introduction of stronger collectors without compromising concentrate quality or circuit stability.Twelve months on, the copper concentrate grade has increased by two per cent and metal recoveries increased by three per cent and seven per cent for copper and gold respectively. The project capital outlay of approximately $2.0 million has been repaid in less than three months. This paper will review the project from the design, construction and commissioning perspective as well as the subsequent debottlenecking exercise that was required to eventually yield the full benefits of this upgrade.

Jan 1, 2005