Search Documents

By D J. Williams, C Zhang, F E. Herrera Cabrera

Farming on bauxite residue using screw propelled equipment (SPE) has been commonly practised to accelerate dewatering and as it promotes consolidation and enhances storage capacity. However, it is unclear when and how often farming should be conducted during the transition of bauxite residue from slurry to dry solids and how deep each slurry deposition should be. To address this issue, three desiccation tanks were established in the laboratory to investigate how much farming could enhance the desiccation and consolidation of tailings. The cuboid tanks, of 350 mm in height and 300 mm in width and length and with an opening on the top, were placed on load cells to monitor the water loss during desiccation and were instrumented with moisture and suction sensors designed and developed at the University of Queensland to measure the water content profile of the residue. The bauxite residue, composed of silt-size particles with low plasticity, was hydraulically deposited in the tanks as a slurry at 27% solid content, resulting in 100 mm depth of solid material settling. Evaporation was enhanced by placing two identical electrical fans above the tanks. Two phases were conducted. In the first phase, the two tanks were left untouched for evaluating non farmed conditions and for calibrating sensors, while in the second phase, three tanks were subjected to atemporal farming using purpose-built screw propelled equipment. The experiment was terminated when the residue was completely desiccated. This paper reports on the instrumented tank set-up and the results obtained to date.

Jul 1, 2021

By P Donecker

Like all chains, iron ore values chains are only as strong as their weakest link, which in ore processing is often the humble chute. While mechanically the simplest element in the iron ore flow sheet, chutes are often the most problematic and regularly the major cause of unscheduled downtime. Chute designs have remained static for decades, despite the extra demands being placed on them by grade reduction, which impacts chutes in three ways viz: 1. Higher volumetric rates as infeed increases to meet production targets. 2. Higher moisture content as mining goes below water table. 3. Stickier properties as the dilution phase is often clay based. While there is no shortage of ideas and the geometry options are infinite, the fact is that chute design has not kept pace with grade decline and has remained essentially unchanged. One reason cited for this lack of innovation is the difficulty evaluating and de-risking designs. While the power of computers running Discrete Element Method (DEM) models has advanced, the models themselves still need to be ‘calibrated’ with the dynamic properties of the ore. Flow properties commonly measured for bin design are useful for static situations only and were never intended to predict dynamic behaviour as in chutes, a critical qualification lost in the mists of time. So while they always produce a colourful and reassuring animation, DEM models informed by static ore properties often result in wildly inaccurate real world predictions. Responding to this low success rate, many operators are now utilising physical modelling to help reduce risk and avoid the consequences of having an underperforming chute in their value chain. Physical testing, in a dimensionless scale-down of the proposed system (bulk material and chute geometry), addresses the shortcoming of mathematical models designs and when used in combination with DEM is the best option. In the ideal world, the focus of chute modelling should be innovative design concepts aimed at addressing future needs, however in reality the focus is nearly always on modifications to installed chutes that are underperforming even today. This situation can be traced back to design procedures which if informed at all, are based static ore properties. As an industry, we need to break this cycle and become more proactive, which means addressing flaws in the current design process. In 30 years of providing modelling support to the industry, I have looking at hundreds of underperforming chutes in the iron ore industry. This practical experience has led to a unique and unbiased perspective on chute design and their performance in the real world. The knowledge presented in this paper can not only be used to help avoid baked-in problems now, but also help guide and evaluate designs so we can deal with the challenges of our low-grade future.

Sep 18, 2023

By A Radici, S Russell

The Dampier Port Upgrade was completed in 2007 and is the largest project in Rio Tinto Iron Ore's expansion program. The project doubled Dampier Port's iron ore shipping capacity over a five year period. Sinclair Knight Merz (SKM) was appointed by Rio Tinto as the Engineering, Procurement and Construction Management (EPCM) contractor to manage Phase A and Phase B of the Dampier Port Upgrade. The aim of the project was to increase the Dampier Port capacity from 74 to 140 million tonnes per annum (Mt/a). This increase in shipping capacity tripled the capacity of the Parker Point facility from 34 to 94 Mt/a, whilst the East Intercourse Island facility increased from 40 to 46 Mt/a. The Dampier port remained fully operational throughout construction and achieved record yearly export tonnages over the period of the project. The $US1.4B project was completed ahead of schedule, on budget and with an outstanding safety record. Significantly the project team set an industry benchmark by achieving five million man-hours Lost Time Injury (LTI) free. The project has been recognised by the Engineers Australia 2008 Western Australian Engineering Excellence awards as category winner in resources and the overall winner in WA, and went on to win a National Engineering Excellence award. This paper provides an overview of the EPCM project management and an insight into some of the key drivers that have delivered this outstanding project.

Jan 1, 2009

By Koeng R, Richardson M, Hoare R

A discrete event computer simulation model was developed for two of the stoping methods currently used at the Z.C. Mines Broken Hill oper- ations. The objective in undertaking this project was to provide an effective tool for mine planning and design to allow comparisons of alternative extraction strategies and attempt to optimise the allocation of capital equipment and human resources. The Slam II simulation program was used in conjunction with ,a com- monly used data editor, text editor and graphics package to allow the simulation to be done on a personal computer with minimum training requirements. The computer hardware used was a portable computer cur- rently available using 80386/20MHz electronics. Specific logic techniques were developed to allow the Slam II language to simulate mining opera- tions because it was originally developed for manufacturing and com- mercial simulations. The design of the model was based on observations and a data collec- tion campaign. The model was designed with flexibility which allows simple editing of the input data which includes: - Insitu volumes - Development statistics -Loadout efficiencies -Loader speeds, availabilities and capacities -Chute numbers, volumes, distances and blockage statistics -Trucking statistics -Work schedules -Utility statistics

Jan 1, 1988

By F Clark, J T. Carswell

Ore definition for final stope planning is often a challenging prospect in underground (UG) gold mines which exhibit high geological and grade variability. Unlike the grade control (GC) scenario in an open pit (OP), the ability for the mining geologist to plan a sampling campaign which effectively characterises the underlying mineralisation is fraught with difficulty. UG sampling patterns are strongly clustered and typically not dense enough to characterise the spatial and statistical properties. Very commonly, sample volumes are not large enough to provide a reliable grade estimate of the surrounding rock. These factors critically affect our ability to accurately map out ore positions and estimate metal quantities.At Sunrise Dam, traditional UG sampling and modelling techniques have proven to be an unreliable strategy for successful stope planning and extraction. The problem was first observed during the final cut-back in the open pit for which the mineral resource model was constructed from UG diamond drilling. Open Pit grade control reconciliations were strongly positive for both tonnage and grade compared to the resource model. Underground workings missed significant quantities of ore which was laterally defined by open pit reverse circulation (RC) GC drilling. Upon examination it was realised that the cause of the problem was one of inadequate sample density and sample support, the implications of which potentially affected the entire UG mine.As part of a broader study into underground grade control procedures, detailed reconciliation of initial stope production from the GQ domain also pointed to inadequate sampling as a major constraint to effective grade control and reserve conversion.To overcome this deficiency, dense 115 mm wet RC grade control drilling and conditional simulation modelling has been successfully implemented with the intent to replicate the grade control process in the open pit. The increase in sample density and sample volume has proven to be a very effective tool for mapping out highly complex mineralisation. A marked improvement in stope definition, reserve conversion and Mine to Mill reconciliations has been demonstrated on the back of an innovative approach to UG grade control.CITATION:Clark, F and Carswell, J T, 2014. Using reverse circulation drilling to improve sampling in a complex underground gold operation – an innovative approach to underground grade control at the Sunrise Dam Mine, Western Australia, in Proceedings Ninth International Mining Geology Conference 2014 , pp 143–152 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 18, 2014

By S Bluhm, LádeáOliveira, R Funnell

Taquari Vasouras potash mine (Vale Fertilizantes) has many interesting features including virgin rock temperatures of 50¦C at depths of 700 m. The mine has a relatively small shaft system with limited ventilation carrying capacity, which was not adequate to exploit the full extent of the deposit. This limitation was overcome by installing two large-scale recirculation systems with underground reconditioning centres. This paper describes this unique mine ventilation and cooling system and some of its history over the past two decades. The two controlled recirculation systems have been operating safely for some ten years and the use of large-scale recirculation has been a fundamental component in the increase of production and extending the mining further-and-further from the shaft centre. The recirculation systems have played a huge role in the mine profitability and comprehensively extending the mine life. The paper also discusses a number of novel design and operating features such as reverse running pumps for energy recovery. The underground chilled water system design required a number of special safety features in order to minimise the risk of water leakage since this could be catastrophic in a potash mine. This paper describes a good example of a mine in which the final ventilation and cooling system design ends up very different to what was envisaged at the greenfields stage.CITATION:Bluhm, S, Funnell, R and de Oliveira, L, 2013. Controlled recirculation and refrigeration at ValeÆs Taquari Potash Mine, in Proceedings The Australian Mine Ventilation Conference , pp 237-248 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 1, 2013

By E J. Sellers, A Cocker

Movement of the fragmented rock mass is an inevitable consequence of open cut blasting. Uncontrolled, unaccounted movement from blasting commonly causes ore loss and dilution from waste mixing. Therefore, the prediction of the post-blast location of both ore and waste is vital in grade control and of direct interest to mining geologists. Direct measurement techniques have matured significantly over the past decade, but their use remains expensive and labour intensive. Access and safety issues are further disincentives to regular movement monitoring. What is needed is a combination of direct measurement to establish baselines and reliable predictive modelling.The W H Bryan Mining and Geology Centre of the University of Queensland has pioneered 3D blast movement modelling using ‘physics engines’ to handle in-flight collisions and predict the final resting place of blasted material. Open cut metalliferous mines are a demanding environment for this style of modelling as they can involve complex geometries and variable buffering, which leads to inconsistent confinement. A version of the model designed to deal with these complexities is under development. A well-controlled field trial was needed to validate this new version.A validation trial was completed at a gold mine in South-East Asia. The aim was to increase throughput by increasing the blast powder factor without losing grade through dilution and mixing with waste. Four blocks were blasted to identify the effect of bench height and face confinement on ore movement, fragmentation and process throughput. The powder factor and blast timing were kept constant. Movement of the broken rock was measured by placing blast movement monitors at known positions in the block and then locating them after the blast. The majority of sensors were recovered, providing a unique insight into blast movement dynamics and generating a substantial data set for model validation.The model (called ‘MetaMove ‘) was calibrated for one blast and applied to investigate the extent of grade loss and possible mitigation strategies. Conventional mining techniques that involved firing across the strike of the orebody, and no post-blast boundary adjustment of the ore/waste boundaries prior to digging, were found to cause up to 44 per cent loss of high-grade ore, depending on the grade distributions. Post-blast adjustment of the ore/waste boundaries can negate this loss. The model indicates that altering timing and ensuring that the block boundaries are well confined can further constrain the movement of ore/waste boundaries. Thus, the model can be successfully applied to minimise grade dilution and limit misclassification of ore as waste whilst using higher powder factors to increase mill throughput. Application of a calibrated model to move ore/waste boundaries prior to digging will enable the production geology team to add significant value to the mining operation.CITATION:Cocker, A and Sellers, E J, 2014. Modelling blast movement for grade control at an open cut gold mine, in Proceedings Ninth International Mining Geology Conference 2014 , pp 377–386 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 18, 2014

"Recognising that the mining industry is wedded to the break-even cut-off grade rather than a cut-off grade that optimises value, the author examines some perils and pitfalls in the use of break-even grades that lead to what the author calls ‘negatively geared ore reserves’.Negatively geared ore reserves occur when a portion of the ore reserves actually has a negative value and is effectively being subsidised by the more profitable portion of the ore reserves. This situation is generally difficult to detect with the level of information available to the public investor. The ore reserves can still be quite profitable in total, but now possess a level of risk that may not be appreciated.The risk profile (financial risk) of a negatively geared ore reserve is far greater than for a non-negatively geared ore reserve. Like a negatively geared investment property in a falling property market (for readers familiar with the Australian tax minimisation investment strategy), when the price of a commodity falls, a company that possesses a negatively geared ore reserve loses value at a magnified rate relative to a company that has a neutral or positively geared ore reserve. In the extreme case of a major commodity price reduction, as happened with the gold price in mid-2013, the negatively geared ore reserve can easily become negative value in total, not just in part.The negatively geared ore reserve is sometimes intentional – for instance in order to increase published ore reserve tonnages and meet the CEO’s key performance indicators – but is also often unintentional, resulting from various errors in the break-even calculation. Common errors in calculating a break-even grade include using fixed metallurgical recoveries, not including allowances for ideal laboratory versus real plant results, ignoring available operational data and using modal rather than mean parameter values in cost and performance calculations.This paper examines a common value distribution profile in many ore reserves and the effect of common break-even grade errors on this profile.CITATION:Poniewierski, J, 2016. Negatively geared ore reserves – a major peril of the break-even cut-off grade, in Proceedings Project Evaluation 2016, pp 236–247 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Mar 8, 2016

Sampling of CIL/CIP circuits is typically done by compositing samples of feed and tails over eight or 12 hour periods. As the residence time in the leaching tankage may be approximately 20 hours, the tails from any period being derived from material entering the circuit 20 hours earlier do not correspond to the head from the same sampling period. Moreover, mixing in the series of tanks in a circuit also modifies correspondence between input and output. A special purpose simulator has therefore been developed to allow for the mixing and delay in the tankage and permit estimation of the head assays corresponding to any tailings sample. Thus more accurate assessment of the day-to-day recoveries of gold and silver follows. The model, programmed in Excel, assumes that the tanks are perfect mixers. By inputting the sequential head grades and considering that no leaching has occurred, the head grade which corresponded to the tailings for each period could be estimated. Allowance is made for variations in feed rate over the sampling period by computing the average flow rate of slurry and thus the residence time of each increment of the tailings. This simple model and its application have been found to be subject to some limitations, which are discussed in the paper, resulting in some unresolved variability in results. However, for a typical circuit even the simple model was able to greatly improve consistency of recovery data with variations being approximately halved by eliminating much of the anomalous variation arising from the lack of correspondence between head and tail when changes in head grade are occurring. Therefore, this permits genuine variations in metallurgy to be identified with greater confidence and thus operational shortcomings can be identified and addressed more quickly.

Jan 1, 2006

"Geometallurgy is a discipline that seeks to improve the sustainability of the extraction of metals and minerals by promoting the smarter use of non-renewable resources, better energy efficiency and greater use of renewable energy. To achieve these goals, development of innovative technologies and approaches are being developed along the entire commodity value chain, starting with exploration and extraction and extending to reuse and recycling. This paper discusses the geometallurgy of industrial minerals with special emphasis on kaolin, a versatile industrial mineral applied in ceramics, paper, paint, plastics, rubber, pharmaceuticals, cosmetics, ink, sealants, adhesives, sanitary ware, glass fibre, toothpaste, animal feed etc. Aspects of kaolin extraction in south-west UK are analysed from a geometallurgical perspective. While geometallurgy already features in kaolin extraction, its role can be significantly expanded by combining advanced in-pit characterisation and orebody modelling with integrated planning and control of the refining and calcination process. This paper highlights the importance of innovation in realising the full potential of geometallurgy.CITATION:Glass, H J, 2016. Geometallurgy – Driving Innovation in the Mining Value Chain, in Proceedings The Third AusIMM International Geometallurgy Conference (GeoMet) 2016, pp 21–28 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Jun 15, 2016

By D Kent, D Eisner

A lot of talk has been generated about the so called ‘Internet of Things’ (IoT) and its potential to transform the way we interact with our homes and devices. But the true potential and value of IoT is not going to be realised by the general consumer but by businesses.This paper outlines the application of IoT in mining and how it is a natural extension to the base networks becoming commonplace in both surface and underground mines. The potential for ubiquitous monitoring throughout a mining operation at low capital and support costs will transform the ability to monitor, analyse, report and manage all of the key processes involved in a mining operation.Importantly, the paper will discuss the practical applications that the IoT offers mining and explain how this really is transformative technology, not just the latest buzz words from the information technology (IT) world. If leveraged correctly the impact on mining, its cost base and efficiencies, is enormous.CITATION:Kent, D and Eisner, D, 2015. What the internet of things means to mining, in Proceedings Third International Future Mining Conference, pp 65–70 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 4, 2015

By L Nienaber

Mines, after becoming operational, often retain the same support and reinforcement designs developed in the feasibility study. These designs are conceived from limited drilling data and regional experience, thus having an empirical flavour. Empirical designs are perceived to be conservative, catering for a variety of failure mechanisms, which are not always present in mine development drives.This begs the question: If you were to invest in the necessary resources to obtain sufficient data and complete the required analyses for the different development drives in the mine, to engineer a support and reinforcement scheme with the capacity to match the demand of the rock mass, what is the difference in cost when comparing an empirical design to an engineered design?To answer this question, mine tunnels with different geometries and orientations, where detailed structural data was available, were selected for a comparative design exercise. Material cost, development cost, cycle time and professional fees for engineered and empirical designs were estimated. The outcome is summarised in the following paper that discusses the process followed and the results of the design comparison.

Mar 8, 2011

By C Harwood, EáWestman, K Luxbacher

Testing of in situ seals in underground coal mines is critical to determine seal integrity and to provide safe working conditions. In the wake of the 2006 Sago Mine explosion, the United States of America (USA) promulgated the Mine Improvement and New Emergency Response (MINER) Act (USDOL, 2006) which required mines to install 827 kPa (120 psi) rated seals or monitor and maintain the atmosphere behind existing 345 kPa (50 psi) seals. The purpose of developing the regulations was to prevent the breaching of seals in the event of an explosion in the sealed area.While seal design and construction is carefully regulated in practice, the construction of seals is difficult to monitor, as many are constructed under various mine conditions and the methods rely on prescribed placement of the seal material. Further examination of installed seals is limited to two-dimensional visual inspection and atmospheric and convergence measuring devices. These methods do not accurately reflect the integrity of the seal and cannot detect changes, deterioration, or defects within the seal.If detection of defects, deterioration and damage is not possible, unexpected communication between the active and sealed areas may result. Additionally, the ability of the seal to withstand explosions may be compromised. Non-destructive testing (NDT) of underground mine seals is necessary to investigate if the seal properties have been altered and if the seal remains functional as a barrier between active areas and sealed areas of the mine. This paper gives a preliminary assessment of proposed NDT methods for seal evaluation using radio frequency (RF) technologies and tracer gas methods.CITATION:Harwood, C, Luxbacher, K and Westman, E, 2013. Non-destructive testing of in situ underground mine seals - Initial technology assessment, in Proceedings The Australian Mine Ventilation Conference , pp 299-306 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 1, 2013

Accurate geometric models of orebodies establish the framework for reliable mineral resource estimates that provide a basis for further exploration and mine planning, as well as for financial models that ultimately determine the economic viability of a deposit. Traditional, explicit geometric modelling techniques that are utilised for resource modelling by the general mining software packages, such as MineSight«, involve manually digitising interpreted ore outlines that must be carefully linked to create valid geometric solid models. An alternative, implicit modelling method, employed by LeapfrogTM software relies on a fast method of global interpolation, which offers several advantages over traditional modelling techniques. Although previous case studies have documented the relative efficiencies of the two approaches, the accuracy of the two methods has not been previously quantified and compared. This study quantifies the accuracy of solid models created using explicit and implicit methods, and compares the differences between the models. Solid models of the Doris Hinge vein gold deposit (located in the Hope Bay district, Nunavut, Canada) are constructed from preliminary and follow-up drilling data using both modelling techniques. The accuracies of the solid models generated using preliminary drilling data are determined by measuring the 3D distance between the surface of the models and the actual contact location defined by the follow-up drilling data. Additional comparisons based on volume, cross-sectional area and surface differences were made between both phase 1 solid models and solid models constructed from phase 2 drilling information. The overall results of this study find that the MineSight« and LeapfrogTM solid model accuracies are virtually the same, and that their volume, cross-sectional area, and surface differences are comparable. This study concludes that the implicit modelling technique generates accurate solid models that can be used in place of explicit models as ore shells for resource estimation in certain circumstances.

Jan 1, 2006

By Johnson MT

The microprocessor revolution of the 1970's dramatically improved the price/per- formance of graphics hardware. Together with improved communications and new software concepts and standards this has resulted in the emergence of a new tool with particular application to the mining industry. The Distributed Graphics Processor (DGP) offers more natural means of interaction with com- plex technical models.

Jan 1, 1983

By H Barrie, L Ameglio

"Current methods for acid rock drainage (ARD) mitigation revolve around insulation of the waste from oxygen in the atmosphere with water and dry (soils and liners) covers. Both are of limited effectiveness and present significant drawbacks. Furthermore, while they reduce oxygen influx, they reduce but do not prevent ARD.The inert gas mixture (IGM) technology has been designed to overcome the deficiencies of gas transfer into tailings and waste rock materials across the surface and instead block oxidation by controlling the transfer of oxygen from the atmosphere. Inert gas is injected into the mine waste at low flow rates and the positive but low flow purges the oxygen that tends to diffuse into the sulfide waste across the surface. The positive flow of IGM compensates for inward oxygen diffusion and creates a pressure drop across the cover layer preventing inward diffusion of oxygen and, hence, acid generation.The IGM processes are evaluated in this paper: theoretically, with a review of the theory of ARD and the current state of knowledge about the performance of notably dry covers as atmospheric oxygen barriers via models to predict the performance of the IGM technique practically, with a bench-scaled experiment.The results demonstrate the effectiveness of IGM to prevent oxidation of sulfide minerals and ARD in waste rock. The laboratory experiments further identified key variables to be used to monitor performance and control efficiency of IGM, which is now awaiting field-scale application.The IGM technology is a patented process by Terraquest Technologies Ltd (Canada) in USA, Canada and Australia. The IGM technology can be cost-effectively manufactured on-site with commercially available compressors and gas filtration membranes. It is predicted that low-cost covers can then be utilised with IGM, which in turn lowers the overall capital costs of ARD mitigation.CITATION:Ameglio, L and Barrie, H, 2015. Acid rock drainage prevention using inert gas mixture technology, in Proceedings Tailings and Mine Waste Management for the 21st Century, pp 85–96 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Jul 27, 2015

With the theme of û æUnderground Ore Handling SystemÆ, Kopanang Mine completed an extensive project on a specific system with technologies for the handling of ore from a dedicated drawpoint to the shaft system. The intended rail haulage tramming system had to be capable of handling the shaft design and Life of Mine (LOM) requirements. Kopanang is an AngloGold Ashanti gold mine situated in the province of the Free State in South Africa. In the Sotho language the name æKopanangÆ means to come together as a team. ItÆs an appropriate name given that 25 companies worked on this project. The future focus at Kopanang is to establish four mining levels between 3 to 4 km south-west of the shaft and two mining levels to the west. The mine has an expected life of almost 20 years and capital was approved in order to access this reserve to establish the infrastructure to handle the ore, hence this exclusive rail haulage tramming system of close to R40 million (SA rands), which took three years to construct. Apart from the fact that this system had to be capable of handling 6500 t per shift at a depth of over 2 km over a length of 3.2 km, some of the major considering factors were: safety, economic factors with improved labour productivity, efficiency and reliability, risk termination, and ergonomics. The system comprises two 20 t locomotives operating in a double header configuration from a dedicated draw point to a dedicated tip area for the reef and waste ore. With the objective of handling high speed and high capacity, this 200 t payload train is capable of running at 35 km/h powered from a 500 volt ac overhead line. Each loco consists of two 90 kW dc motors with ac/dc power conversion on the locomotive. For the system to operate at this speed, the rail system is constructed with Class 1 rails over the entire hauling distance. The tipping mechanism is unique and the span of 11 hoppers each with a load of close to 20 t is capable of tipping the pay load of 200 t in about 20 seconds hands free.

Jan 1, 2005

By S Kakara, A Kamaraj, S S. Varanasi, B V. R Mandalika, M B. Shaik

The properties of top slags play a very important role in secondary steelmaking. Fluxes should be chosen based on the ladle furnace (LF) slag requirements like viscosity, melting temperature, sulfide capacity, etc. CaF2 and CaO-Al2O3-based synthetic slags are the most used fluxes in secondary steelmaking to improve slag fluidity and interfacial chemical reactions. CaF2 is obsolete due to fluorine pollution and CaO-Al2O3 based slags have 40–50 wt per cent Al2O3 and 30–40 per cent CaO which is not beneficial for desulfurisation. Yet another drawback is that LF slag disintegrates into fine powder during cooling due to phase transformation C2S (2CaO.SiO2). Hence, there is a need for the development of low melting fluxes with high CaO content and the capability to prevent slag disintegration. The current work studied the effect of 0–9 wt per cent B2O3 on physico-chemical properties and characterisation of LF slags. X-ray diffraction (XRD) analyses were carried out to identify mineralogical phases present in slag and Fourier-transform infrared spectroscopy (FT-IR) analysis was done to understand the changes in bonds of B2O3 added LF slag. The characteristic temperature of slag was determined by a hemispherical method using high-temperature microscopy. Empirical models were used to calculate viscosity, break temperature, and sulfide capacity. FactSage™, ver 8.2 (by GTT-Technologies) simulations were carried out to find the equilibrium phase fractions and percentage of liquid slag at different temperatures. New phases such as Ca11B2Si4O22 and Ca2B3O5 were formed in LF slag with B2O3 addition. Based on the results, 0.5–1.0 wt per cent B2O3 was found to be sufficient to prevent C2S-driven disintegration of LF slag. Also, the melting temperature and viscosity of LF slag were reduced by adding 3–8 wt per cent B2O3 due to the formation of BO3 planar triangular structure and low melting eutectics in slag. Liquid slag started forming at a temperature as low as 800°C when B2O3 is >6 wt per cent. It was found that the sulfide capacity, viscosity, and break temperature of the slag decreased with increasing wt per cent B2O3. Based on the analysis carried out, B2O3 can be a promising fluxing material in secondary steelmaking, for improving the desulfurisation kinetics and valourisation potential of LF slag.

Aug 21, 2024

By E Amini, N Beaton

Application of ore pre-treatment technologies such as Grade Engineering and in-pit ore treatment require comprehensive analysis to show proven value is being generated by switching away from the current practices. Considering most mining operations last several decades; the pre-treatment technologies must be investigated over life of mine (LOM) to truly show value was generated or lost. Therefore, a value chain flowsheet model has been usually developed to run those analysis/simulations over LOM using a set of defined ore characteristics and the operating equipment capacities. The Integrated Extraction Simulator (IES) has been used for this type of LOM simulations as it has the necessary flexibility to accommodate the whole mining value chain flowsheet in one platform and provide essential computation power to run mass simulations for the given scenarios using the resource block model. This allows to forecast the value chain response over the LOM for all given scenarios in a feasible amount of time. The traditionally developed flowsheets for the analysis/simulations are usually limited to the mineral processing plant and were developed based on a single audit conducted on the plant in a very short time, e.g. several hours. The process plant is being operated with a certain ore at a certain condition during the short audits which would not reveal the true capacity of the operation equipment when ore characteristics changes. Therefore, it would be impossible to define the true capacity of the equipment and identify the constraints along the value chain. In this study, a methodology was developed to identify the constraints along the value chain and implement those in the IES flowsheet using process information. Also, the equipment models were fine-tuned to represent the true capacity of the equipment in the flowsheet using the same data set. The methodology was tested over five process plant in two operations and showed the performance forecast was significantly improved over the traditional methods being used so far. Then those high-fidelity flowsheets were used to evaluate the ore pre-treatment technologies proposed by the relevant resource company experts.

Nov 10, 2020

By E Kabwe, M Karakus

Deep hard rock underground mines tend to experience high stress as such drives exhibit dynamic responses attributed to a rock burst variant (strainburst). This dynamic behaviour is difficult to predict, and every effort is made to devise the appropriate dynamic support system for its associated failure restraint. This paper outlines the back analysis and the support scheme design for an underground decline that exhibited damage from a dynamic strainburst occurrence. It employs a decline section that experienced a dynamically loaded strainburst that initiated rock fragment ejections. The procedure involves a preliminary structural analysis, a seismic intensity measure, and a rock mass simulation to determine the static stress concentration and ground support system response. The numerical simulation is conducted in FLAC3D which employs the advanced strain-softening IMASS constitutive model governed by two Hoek–Brown (HB) bounding yield surfaces. To account for the post-peak brittleness response associated with strainburst the plastic strain multiplier () is adjusted to 0.0 < < 1.0. The back-analysis shows that the occurrence was initiated by a low-intensity seismic wave that superimposed an extra stress component to the initial static stress which triggered rock fragment ejections. Additionally, the appropriate support scheme comprised of Weldmesh, Fibrecrete, static (split set) and yieldable (Kinloc) reinforcements is recommended and implemented. Thereafter, the bolt’s efficiency is evaluated based on the axial force and elongation capacities and then compared with the published bolt performance data. The evaluation results show that the maximum bolt axial force (0.1 per cent) and elongation (0.006 per cent) are below the designed capacity and rupture strain.

Nov 29, 2022