Search Documents

By G. E. Murray

Lead blast-furnace work at Trail is unique in that this is the only plant in the world where blast-furnace smelting on a large scale for both lead and zinc recovery is carried on under one management. On this account the factors that determine economic practice differ from those of other lead smelters. In addition to this different metallurgical outlook, a great deal of structural investigation has been carried on, which has resulted in the development of a furnace which should prove of interest to all who are faced with similar problems. This description may be conveniently divided into various heads as follows: (1) General—make-up of charge, etc.; (2) structural—(a) hoods and charging methods, (b) shaft construction, (c) crucible construction; (3) handling slag; (4) handling bullion; (5) metallurgy. The Charge The Trail plant is an old one, on a congested site. As with most old plants, this limits the method of charge preparation. In general, lead metallurgists will agree that sinter when it reaches the blast furnace should contain as small an amount as possible of actual fines. There would be some difference of opinion as to the maximum size as well as of the minimum required, but to obtain the optimum condition some form of screening is indicated. This screening should take place immediately before the blast furnace if possible, and because sinter deteriorates in storage there should be as little as possible. There should also be the minimum amount of handling between the sinter machines and the furnaces. Unfortunately, at Trail the sinter must be handled considerably before it is charged to the furnace, and no feasible scheme of screening has yet been devised. Trail practice, then, demands that the sinter be a strong one physically. Dependent upon the amount of lead in it, it has been found advantageous to incorporate granulated slag into the final sinter, the amount varying inversely as the lead content. The addition of this slag makes a harder sinter, which arrives at the blast furnace in a better condition, but it entails some lack of efficiency, because desulphuriza-tion is not so rapid nor so complete.

Jan 1, 1937

By Ben L. Seegmiller

Roof, pillar and floor stability is a most important requirement in underground coal mines because it represents the leading cause of fatalities. In future coal mine planning the geotechnical aspects must often be minimized owing to unavailability of data. It is, therefore, very important to include a geotechnical investigation as part of the coal exploration program. Data which should be collected basically include the geological discontinuity characteristics, the rock strength characteristics and the groundwater aspects. Many times the only source of such data is the exploration boreholes. Therefore, an emphasis must be made to extract the maximum information from the core and the borehole. Data collection methods can include the preparation of detailed geotechnical logs for the roof, coal and floor. Laboratory strength testing will provide estimates of the mechanical properties of the various lithologic types. Slaking and swelling tests provide an insight into the stability characteristics of the rock materials immediately enclosing the coal seam. The boreholes may be used to provide permeability and pressurization data. Having developed a suitable geotechnical data base allows various stability prediction methods to be used. These include a geotechnical appraisal of the roof and floor units, depositional environment methods, multiple overlay techniques, hazard analysis techniques and classification/rating systems for roof and floor. The basic geotechnical data and the stability prediction methods form a basis upon which preliminary rock mechanics designs may be developed. Of particular importance to future coal mining are those designs relating to longwall mining because most companies are thinking in terms of the greater safety and greater productivity offered by longwalls. Items which should be ad- dressed when considering a longwall system include the panel layout in terms of a total mining plan, strata mechanics, roof/floor bearing capacities, face support requirements, face length, entry and pillar

Jan 1, 1983

By A. W. Gauger

For perhaps one hundred years scientists have been engaged in attempts at devising a satisfactory method of classification of coal. During this time many charts, tables and graphs have been proposed, some of which have had considerable merit, but no one system has been found to be applicable to all ranks of coal, nor has any one system received general acceptance. In many of the proposals, water eliminated between room temperature and 105" C. has been regarded as extraneous matter and calculations have been made to the air-dry or water-free basis. Such methods of calculation do not lend themselves to satisfactory grouping of the high-moisture coals.1, 2 A consideration not only of the properties of the high-moisture coals and their behavior on drying but of the generally accepted ideas of the coalification process and the role of water in this process indicates that water is an essential constituent of all coals and therefore should not be neglected. For example, in such low-rank coals as the lignites of the Northern Great Plains' deposits the inherent moisture of the lignite as mined plays a very important part in the physical properties thereof. Freshly mined lignite contains upwards of 30 per cent water and is extremely tough and resistant to shock. Upon exposure to the atmosphere, the lump loses part of its moisture and checks and splits, leaving a friable and broken up residue. So far as we have been able to determine, water is the only thing lost in this process and we are forced to the conclusion that moisture plays an extremely important part in the structural properties of the original lignite. With reference to the coalification process, Mack and Hulett3 pointed out in 1917 the important part that water played therein. They observed that water cannot be removed from peat or coal by pressure alone, but only as the result of chemical reaction, and suggested that peat in its early stages may be largely a hydrosol. Slow chemical changes occur over a long period of time until finally the mass becomes more largely a hydrogel. These views are substantiated to some extent by the experi-

Jan 1, 1932

By Sidney Powers, Alfred C. Lane

This paper aims to present the results of an investigation concerning gravitative differentiation in lava flows, based on a quantitative microscopic and chemical study of a Triassic basalt from Nova Scotia, and confirmed by data secured from a study of certain Keweenawan ophites. At Cape d'Or, Nova Scotia, near the head of the Bay of Bundy, marine erosion has exposed a series of Triassic basalt flows in which copper has been sought for a number of years. Studies of the thickest flow of the series with regard to volumetric composition, specific gravity, and grain have been made by the junior author, and measurements by students at Tufts College, together with confirmatory observations of the same nature on this and other flows by the senior writer, and chemical analyses made by the Division of Chemistry, Mines Branch, Ottawa,' all show differentiation in lava flows comparable to that in intrusive bodies. The work was made possible by the availability of the drill-cores, the property of Tufts College, and emphasizes the desirability of the study of drill-cores from other localities. Measurements of the specific gravities of certain Keweenawan lava flows of Michigan by the senior author, from material collected in 1915, will be given as a comparison to those of the Cape d'Or flow. It has been found that the specific gravity of drill-cores, or volume per cubic foot, can be readily obtained by measuring their dimensions. This can be done to an accuracy of within 1 per cent. in pieces of core over 100 mm. in length by using a micrometer gage for the diameter, and taking the average of six measurements of the diameter; and the average of four measurements of the length made with a finely graduated ruler. Then, after weighing them, the weight in grams per cubic centimeter, or what is practically the same thing, ounces per cubic foot, is obtained. System-

Jan 1, 1916

By Auguste J. Rossi

We cannot expect, within the limits of this paper, to treat this subject exhaustively, but will endeavor, in the following, to present it in as concise a manner as is consistent with a clear exposition of its importance. Ores of titanium, titaniferous iron-ores (that is, iron-ores containing a notable amount of titanic acid, TiO2,, say not less than 5 per cent., generally 10 to 20 per cent., and frequently more, up to 40 per cent. or thereabout), occur all over the world in immense quantity, " in mountain masses," constituting in some localities, as in Sweden, Norway, Canada, the Adirondacks (N. Y.), in North Carolina and other States of the Union, the geological formation itself, the igneous rocks having, in many places, been so permeated with the metallic oxides as to justify their being called iron-ores. As a rule they are Bessemer ores, quite free from phosphorus and sulphur, though not invariably so. When the percentage of titanic acid is very high, that of the iron is low, but the proportions do not necessarily vary in the same ratio; that is, a rich ore may contain more titanic acid than one lower in iron. The percentage of iron varies, being as low as 35 to 36 per cent. in real ilmenite. It is more generally not less than 50 to 55 per cent., reaching often an average of 58 to 60 per cent., and as high as 63 to 65 per cent. It is obvious that if these ores were to be considered in the same light as other iron-ores, equally rich in iron, they would form an excellent stock for blast-furnaces for years to come, as their supply might be called inexhaustible, and they could

Jan 1, 1903

By James P. Kimball

In a paper which I had the honor to present to the Institute at the Montreal meeting, September 1879,I took occasion to refer incidentally to certain practical difficulties in the sampling of coal-seams {Trans. Vol. VIII., p. 181-3). This reference was particularly to the unequal distribution of sulphur in the form of pyrite, and to the necessity of discriminating between the several members or " benches " of a coal seam as to their relative proportion of visible sulphur. What is a practically truthful estimation of the sulphur of a coal seam, is not necessarily the estimation of an average of sulphur in any given line of cross-section of the seam. Cornparatively speaking, the range of sulphur in quantity is generally so low that errors in its determination, arising from neglectful sampling or from slips in the laboratory, fall chiefly upon this single ingredient. Not so,

Jan 1, 1884

By A. E. Bellis

The problem of heat treating high-speed steel becomes more and more important as the design of cutters becomes more and more complicated in increasing the efficiency of mechanical operations. Hundreds of dollars' are spent in the design and manufacture-of milling cutters of special form ,for rapid production of duplicate or interchangeable parts, and then, as the heat treatment is faulty on the one hand, or scientifically executed on the other, the tool fails after a few operations, or its efficiency is greatly increased. The practical operation of giving these complicated tools the right temperature necessary to bring out the best cutting qualities, and at the same time bring the tool out "clean," is a difficult: one and calls for no small amount of skill. In order to be on the safe side, the average tool hardener uses a temperature much too low to give the best results with the high-speed steel he uses. In the case of cutters which are finished to a given diameter before hardening, it is impossible to grind the tool after hardening, so that it is essential that the surface be-protected from oxidizing or de-carbonizing. It is the aim of this paper to describe some experiments on hardening high-speed steel, in which metallographic means were used to determine the correct hardening temperatures. The accompanying table and plates show the results of hardening experiments on five different high-speed steels. The analyses for carbon, tungsten, chromium and vanadium of each steel are given in the accompanying table. Six specimens from the same bar :of each: kind of steel

Jan 1, 1917

By B. R. Palmer, M. C. Fuerstenau

Oxide and silicates respond to flotation with a large number of anionic collectors. These include carboxylates (fatty acids), sulfonates, alkyl sulfates, and certain chelating agents. In contrast to sulfide mineral flotation, relatively long-chained collectors (generally longer than 10 carbons) are required to effect flotation of this group of minerals. The structural formulas of these various anionic collectors are presented in Table 1. Formulas and solubilities of various fatty acids are presented in Table 2. These solubilities are those of the dissolved and undissociated species of the acid, e.g. oleic acid, HOl(aq). Of the compounds listed, oleic acid and abietic acid, which IS a major constituent of talloel, are used most commonly in commercial applications. The usage of these two collectors is related to cost and effectiveness. In addition to their high molecular weights, oleic acid contains a double bond in its hydrocarbon chain, while abietic acid is comprised of aromatic rings containing double bonds. The presence of double bonds increases solubility significantly over that of saturated homologues. Stability of metal-collectors assumes a most significant role in these systems, and the solubility products of various metal carboxylates and sulfonates are listed in Tables 3, 4 and 5. In addition to these properties, strength of the acids of these various anionic collectors is also important. The carboxylic and hydroxamic acids are weak acids whereas sulfonic and alkyl sulfuric acids are strong acids. All of the carboxylic acids fall in the range of pK = 4.7 ± 0.5 ([2]); the pK of hydroxamic acid is around 9 ([3]); and the pK of sulfonic acid is about 1.5 ([4]).

Jan 1, 1976

By R. L. Huntington, L. S. Reid, Chen Chun Ku

The simultaneous adsorption of water and hydrocarbon vapor from natural gas by three grades of alumina has been studied at atmospheric pressure and temperature. Results of this investigation reveal that the presence of water vapor in the gas inhibits the adsorption of hydrocarbon vapor, although the presence of the latter does not have a pronounced effect upon the adsorption of water vapor. Adsorption of water-hydrocarbon mixtures from gas is divided into three phases. In the first, both water and hydrocarbon vapor are adsorbed; in the second, adsorption of water vapor proceeds while desorption of hydrocarbon takes place; in the third phase, the adsorbyt approaches complete saturation with respect to both water and hydrocarbon vapors. Both theory and experimental data can be applied to design and operation of commercial dehydration plants, and an illustration is presented. Introduction Dehydration of natural gas becomes increasingly important as the operating pressures employed in gas processing and transmission are increased above 500 ib. per sq. in. Gas produced from high-pressure wells is saturated with water vapor when it leaves the reservoir and it continues into the processing plant or transmission system in a saturated condition because of the substantial decrease in temperature due to expansion at the wellhead. Usually this gas is accompanied by liquid water and hydrocarbons that have condensed with the change in temperature and pressure. Without dehydration, gas temperatures must be held at relatively high levels to prevent solidification of gas hydrates. According to Hammerschmidt's data8 on the relationship of pressure to the freezing point of natural-gas hydrates, the minimum safe operating temperatures range from 55' to go°F. for pressures ranging from 500 to 3000 lb. per sq. in., respectively. Often it is difficult to maintain gas temperatures above the hydrate-freezing temperature because of climatic conditions, unless flow-line heaters are installed. Also, in processing gas for its gasoline content at high pressures, it is desirable to employ operating temperatures lower than the hydrate-freezing point. In distributing high-pressure gas, the large pressure drop from line pressure to town-gate pressure often prbduces sufficient cooling to freeze the regulators and disrupt consumer service. Therefore, it is highly essential to dehydrate high-pressure natural gas if smooth and economical operation is to be maintained at all times. Few published data are available on the simultaneous adsorption of water and hydrocarbon vapors. The literature contains many mathematical expressions for rate of adsorption in various systems but a rational correlation of the existing rate

Jan 1, 1944

By Henry M. Howe

SECTIONS 1. INTRODUCTION.—In this investigation the meltingpoint and the specific heat of certain artificial silicates were determined by the method of mixtures, using a large platinum-ball pyrometer. The silicates were placed in platinum crucibles on the hearth of a small regenerative gas-furnace (Figs. 1 and 2), and the platinum ball was placed between them. The temperature of the furnace was usually raised very slowly, the behavior of the silicates being observed as they gradually grew hotter; and their temperature was ascertained indirectly from time to time by determining that of the platinum ball, which to that end was temporarily withdrawn from the furnace and immersed in a known weight of water in a calorimeter. The weight and specific heat of water and of platinum ball being known (the specific heat of the latter approximately), it mas possible to calculate the temperature of the platinum ball, which was assumed to have been substantially that of the silicates which surrounded it in the furnace. The specific heat of the silicates also was determined by the method of mixtures. Their temperature having been determined as just described, one of them was dropped into a known weight of water in a calorimeter, whose rise of temperature was then noted. Knowing the weight and initial temperature of the silicate, its specific heat was wily calculated. The reults obtained, especially as regards the melting-point, must be regarded as first approximations. The technical difficulties encountered were so serious as to raise doubts, now from one cause, .now from another, as to the accuracy of most of the results: hence I give but a few, those which were reached without mishap, and with proper observation of the various precautions. The difficulties encountered are referred to again in Section 6. The investigation was carried out in the metallurgical laboratory of the Massachusetts Institute of Technology, and part of. The

Jan 1, 1890

By T. S. Spicer, C. C. Wright, R. G. Bowman

IN recent years considerable publicity has been given to the problem of atmospheric pollution by fuel-burning equipment. Legislation has been stimulated and smoke ordinances have been enacted, the provisions of which show a definite trend toward stricter control of the emissions not only from the stacks of industrial fuel users but also from the chimneys of domestic consumers. As a result of war conditions, some slackening in the enforcement of these ordinances may be noted, but this is only a temporary expediency caused by the changes necessary in the distribution of the nation's fuel supplies and difficulties in securing the necessary equipment. Previous trends may be expected to continue in the postwar period. Largely because of the consumer demand for automatic heat, but partly because of the legislation against smoke emission, there has been a marked increase in the use of domestic underfeed stokers with the past decade. When correctly adjusted and operated, these units reduce the smoke emission materially, so that even the high-volatile bituminous coals may be burned with little or no emission of objectionable smoke. Unfortunately, however, the use of the domestic underfeed stoker introduces another problem; namely, fly-ash. PRODUCTION OF FLY-ASH The term "fly-ash" is a misnomer, since the fly material is generally a mixture of small carbonaceous particles varying from green coal to coke, and inorganic particles ranging from fluffy ash to small particles of fused clinker. For want of a more comprehensive name, however, the term fly-ash is used throughout this paper to include all the fly material. Even with hand-fired furnaces a certain amount of fly-ash is produced, which necessitates periodic cleaning of the boiler flues or furnace radiator, the smoke pipe, and occasionally the chimney itself. With stoker operations the amount of fly-ash is increased many fold, because of the higher velocity of air travel through the fuel bed. Frequently the amount of this fly-ash attains such proportions as to constitute a definite nuisance to the householder and his neighbors and distracts very materially from the otherwise automatic or semi-automatic performance of the stoker. Virtually all the boilers and hot-air furnaces marketed in the domestic field

Jan 1, 1944

By Charles R. Keyes

PAGE I. Introductory............ 140 II. Location and History...........140 III. Surface-Relief of the District....... 141 IV. General GeoloGic Features........ 142 1. Main Relationships and Map....... 142 2. Résumé of Geologic History..143 V. Geologic Formations Represented...144 1. Broader Considerations......... 144 2. Geologic Section.......... 145 3. Nomenclature.......... 146 4. El Pasan Limestones..146 5. Santa Rita Limestone.... 146 6. Silver Shales........... 147 7. Bella Shales........... 147 8. Berenda Limestone..147 9. Grande Limestone... 148 10. Lake Valley Limestone........ 148 11. Sierra Limestone.......... 149 VI. Unconformities........... 149 VII. Geologic Structure.......... 150 1. Main Characteristics......... 150 2. Folding........... 1.50 3. Faultings........... 150 4. Relations of the Eruptives...153 VIII. Geologic Relations OF the Ore-Bodies...... 154 1. Governing Factom......... 154 2. Position.......... 154 3. Relations to Foldings...155 4. Relations to Lines of Dislocation... 15.5 5. Relations to Present Surface.Relief..156 6. Relations to Eruptive Rocks...157 7. Relations to Lithologic Nature of the Rocks.... 158 IX. MINERALOGIC CHARACTER OF THE ORES...... 158 X. Origin of the Ore.Deposits..159 1. General Statement......... 159 2. Original Source of the 0re.Materials...160 3. Contact-Metamorphism of the Region... 161 4. Process of 0re.Concentration..162 5. Lowering of Ground-Water Level..162 6. Formation of Cerargyritic Ores...163 XI. Recapitulation........... 168

Jan 1, 1909

By R. Thiessen

The question whether the kind, rank and grade of coal is in any way determined by the kind or type of plant from which it originated has been a problem since coal was first studied. Some investigators claim that the kind of plants has contributed none of the attributes that characterize the differences found in the various coals; others claim that all differences are caused by the contributing plant; and others hold that only a few characteristics are inherited from the kind of plant from which the coal originated. Most coalologists, however, give this matter no thought. It can easily be shown that the kind of plant which contributed to a coal had a marked influence on its kind and type. A number of factors enter into this problem, and all unrelated ones must be carefully eliminated, including metamorphism caused by the pressure of the cover, earth movements, mountain building and higher temperature. Only the fundamental substance—the plants out of which coal was formed—• and the causative conditions that gave rise to a peat swamp and the conditions imposed upon the plant and the plant substances during the formation of the peat swamp can be considered. Everything else being equal, the question then is, how far do different classes and types of coal owe their differences to different kinds or types of plants? Geologic Age of Coal Coal has been laid down in almost every geological period since the Devonian era. Even as early as the middle Devonian some coal was formed; although of no value it has great scientific significance. The most valuable coal was deposited during the Carboniferous. The coals of England were formed during the Mississippian, and most of the valuable coals of America, Europe and China during the Mississippian and chiefly the Pennsylvanian. From the Permian come the coals of France, Saxony, Thuringia and Schwarzwald in Germany and of Bohemia and of the Ural districts of Russia. From the Mesozoic come the coals

Jan 1, 1930

By C. D. Hunter, J. B. Browning

During the year 1934, Kentucky oil and gas operators have partly overcome their past depression fears and in the oil industry, with possibly more abandonments of old oil producers than the completion of new oil wells, produced 4,814,904 bbl. of oil in 1934 against 4,501,511 bbl. in 1933. In the gas industry of eastern Kentucky, 115 gas wells were completed during 1934. This production is delivered through two 20-in., one 16-in., one 12-in., one 10-in., and two 8-in. pipe lines to supply both domestic and industrial markets in Cincinnati, Ohio; Louisville, Lexington, Frankfort, Winchester, Ashland, Covington and other Kentucky towns; Washington, D.C., and other eastern cities. The largest percentage of these gas wells and production are from the Devonian black shale area of Floyd, Pike, Knott, Martin and Magoffin counties, Kentucky. In this area the largest percentage of 1889 wells, developing 421,-215 acres, has been completed in the past 10 years, of which 55.3 per cent produce from the 400 to 550 ft. of Carbonaceous Devonian black shales. The successful results obtained from these Devonian shales are due to the physical effects of the 5000 to 6000 lb. of gelatinated nitroglycerin with which the entire 400 to 550 ft. of shale is shot. A very small number of the shale wells are natural producers and do not require shooting. Other than the Devonian shale gas production, the remaining 44.5 per cent of the gas in this field is encountered throughout the entire strati-graphic section above this horizon; namely, salt sands of Pennsylvanian age and Maxon, Big Lime and Weir of Mississippian Age. A very small percentage is encountered in the Corniferous Devonian lime and the Silurian Big 6 below the black shales. In western Kentucky, in the counties of Henderson, Webster, Hopkins, McLean, Christian, Muhlenburg, Ohio, Daviess, Hancock, Brecken-ridge, Hart, Barren and Warren, many gas wells have been completed, but, because of insufficient market, activity has been somewhat desultory. The area is served by the pipe lilies of the Kentucky Natural Gas Corporation, with headquarters at Owensboro. Their market is increasing and the gas is delivered to Owensboro, Henderson, Madisonville, and many

Jan 1, 1935

By H. Hu

Observations were made on the recrystallization of a 70 pct cdd-rolled silicon-iron crystal with an initial orientation of (113) [332]. Its polygonization and recrystallization characteristics were studied. Results indicated that re crystallization tendency of the deformed crystal is much weakened by the polygonization of the matrix. Complete recrystallization in such specimens is achieved by the growth of recrystallized grains of sufficient size and of the right orientations in relation to the matrix. Evidence was also furnished which suggests that the difference in the re-crystallization tendency is a result of the difference in the severity of lattice bending rather than the difference in orientation of the deformation texture. DUNN and Koh1,2 have made an extensive study on the rolling and annealing textures in silicon-iron crystals. Their results indicated that the recrystallization tendency can be widely different in crystals with different orientations. A particularly interesting example of their results was a crystal with an initial orientation of (113) [332], which developed a deformation texture of (001) [110] after 70 pct cold-rolling. Recrystallization in this crystal took long time anneals at high temperatures. Other crystals having different orientations recrystallized very rapidly. Wiener and corcoran3 have observed the retention of the (100) [011] deformation texture in a low-temperature annealed specimen of a commercial silicon-iron alloy, corresponding to areas of light-etching low-angle boundaries in the annealed struc-

Jan 1, 1960

By J. R. Thoenen

Six or seven years ago the United States Bureau of Mines started development of instruments for the purpose of accurately measuring the vibrational movement of the earth in the vicinity of quarry blasts. For this work a new type of seismometer has been developed. A number of these have been constructed, the accessory field equipment has been assembled, and approximately 200 field tests of actual quarry, blasts have been made. The results of some of these tests have been published 2/ and others are the subject of two manuscripts now in preparation. So far the attention of the investigation has been centered on ascertaining the characteristics and behavior of the ground vibrations. Occasionally, when opportunity arose, measurements of the vibrations occurring in houses or other structures caused by-quarry blasts were made, but without any attempt at direct correlation or interpretation. During 1936 the National Bureau of Standards conducted some experiments to determine the normal vibrations to which the wells and floors of buildings are subject. Cooperation of the Bureau of Mines was requested in measuring the displace-ment. This afforded an opportunity to study the affect of mechanically induced vibrations end make limited comparison with previous records of vibrations from blasting. This paper deals with the experiments made in cooperation with the Bureau of Standards and includes some comparisons with effects from quarry shots. The results are in the nature of a progress report only, and are not intended to draw definite conclusions. These tests were concerned with the determination of the maximum amplitudes of vibration possible in the floors and walls of a typical dwelling when subjected to commonly experienced vibrations. The dwelling tested was obtained by the National Bureau of Standards. It was a large four-story stucco building, 41 ft. south of the southerly curb of Park Road, in Washington, D.C., which was constructed about 1900 and was supported on overburden. The basement floor elevation was approximately that of the pavement of Park Road, Park Road runs east and west; the front door of the house faced north.

Jan 1, 1937

By Edward Steidle

It has been said that "the command of nature has been put into the hands of man before he knows how to command himself," and what we see about us gives particular emphasis to this observation. If this condition be granted, the vaunted boast of school and college, of the institution that had the training of this generation, and of its fathers, and of its grandfathers, the boast that education is a "preparation for life," stands exposed as a hollow claim, or as a ghastly, cynical conception of life, or else education has fallen far short of its intentions. It has been evident for some time that education was not meeting the fullest expectations of society. In recent years there has been a deal of speculation indulged in by both laity and faculty in regard to American education and American civilization, and some few and sporadic changes have been effected. Today, however, there is no longer time for mere hypothetical considerations; we are faced with certain definite facts and confronted with obvious conditions that will not wait for fine-spun theories. If educators do not put their house in order, someone else will do it for them. The trends in mineral industries education must be in harmony with this general realignment that is today visible on the educational horizon, and only as these trends are in conformity with this movement can they be called sound. Two questions, then, confront mineral industries educators: (1) What are the trends in mineral industries education, and (2) how do these trends correlate with the major educational movements of the day? Scope or Mineral Industries Education Before launching into these particulars, it might be well to define the scope of mineral industries education and to consider its present position. Mineral industries education embraces three main types of work: 1. Earth Sciences and Geography.—Geology, mineralogy, geography— courses basic to all mineral industries and to the humanities. 2. Mineral Engineering.—Mining, petroleum and natural gas—dealing with mineral producing industries. Application of earth sciences and all types of engineering to exploitation of natural mineral resources.

Jan 1, 1934

By C. H. Bushell, M. Malnarich

REAGENT control in flotation is more an art than a science. Operators vary the amount of reagents used according to the metallurgy obtained. The amount of collector may be increased, for example, if tailings losses are high and decreased if concentrate grades are low. Often control decisions are based on only one assay, such as the tailings analysis by microscopic or quick assaying techniques. This method of control has given reasonably satisfactory results but is clearly far from perfect. No adjustment in reagent addition can be made until information is received that metallurgy has deteriorated, that is, until the optimum time for adjustment has already passed. The first adjustment probably will be an overcorrection or an undercor-rection, and time will be required to establish the best new addition rates. The seriousness of the problem depends on variability of the ore. In ore of continually shifting composition and complexity, mill results will shift back and forth from excessively high concentrate grades and high tailings losses to excessively low concentrate grades and low tailings losses. Economic incentive for improved control also increases with increasing size of mill. Even a small improvement in percentage recovery in a large mill pays for expensive control equipment. The Sullivan concentrator of The Consolidated Mining & Smelting Co. of Canada Ltd. at Kimberley, B. C., treats 11,000 tpd of complex lead-zinc ore, a scale of operations which justifies an extensive research program on automatic control. Work has followed two separate lines: 1) development of faster analytical methods for pulps, and 2) study of metallurgical control by measurement and control of reagent concentrations in flotation solutions. Although work is incomplete in both phases, a progress report can be given on the development of reagent control. The primary requirement in flotation is selective attachment of particles of one mineral to air bubbles while the other minerals remain detached. Hydrophobicity of mineral surfaces is established by the collector, which coats the minerals by adsorption. The requirement of selective affinity for air bubbles is therefore equivalent to requiring selective adsorption of a collector. Adsorption theory, supported by abundant experimental evidence, shows that the amount of a reagent adsorbed at a surface must be a function of its residual concentration in solution. As the concentration in solution rises, the amount adsorbed increases, usually following some type of logarithmic curve. Selective adsorption must depend on a natural difference in the minerals, but ordinarily the differences in affinity are not great enough to obtain complete coverage of one mineral while the others are completely uncoated. An optimum concentration will exist, below which coverage will not be great enough to float enough of the valuable mineral, and above which too much unwanted mineral will float. All other reagents, except some frothers, affect the amount of collector adsorbing at constant residual collector concentration in solution, either by adsorbing competitively with the collector, or by a

Jan 1, 1957

By R. E. Grace, H. W. Schadler

DARKEN1 has established the theoretical relation between the self-diffusion coefficients and the Boltzmann-MatanO Or interdiffusion coefficient: D is the Boltzmann-Matano or interdiffusion coef-

Jan 1, 1960

By J. W. Pugh

PREFERRED orientations in cold-rolled body-centered-cubic metals appear to have remarkable similarity. The as-cold-rolled textures in iron,1,2 silicon-iron,3 mild steel,4 molybdenum, vanadium,&apos; chromium,&apos; tantalum,&apos; tungsten,&apos; and a-zirconium-niobium alloys10 have been determined. These textures have, in some cases, been represented by congrUOUS pole figures and have all been described in one or both of two ways. They have frequently been reported as predominantly (100) <011> orientation

Jan 1, 1959