Search Documents

By R. J. Pfister

The development of a water-input profile instrument based on the introduction of brine and fresh water into an input well with the electrical location of, the boundary developed between them is reported. Two methods are available in the use of this instrument to measure the foot by foot water-intake rates of the various sand strata: the moving boundary method in which variable well bore diameters can be determined and/or cancelled out and the constant boundary method. The type of results obtained and the relative advantages of each of these methods are described in detail. Representative data are included covering the use of this instrument in experiments involving selective acidizing, selective plugging, and selective shooting. In such experiments, this instrument has been used to diagnose the unfavorable distribution of water intake in input wells and also to determine the effectiveness of the resultant treatments. The data included also serve to illustrate the type of problems which can be studied with this technique. Introduction For ten years or perhaps longer a number of progressive water-flood operators have felt the need for some to to measure the foot by foot water-intake rates of various strata in water-injection wells. The primary need is to diagnose unfavorable water distribution in various strata and to evaluate the effectiveness of the corrective measures such as selective acidizing, selective plugging, and selective shooting. Previously described methods for obtaining this type of data were not considered entirely adequate.l,2 The profile equipment described in this paper embodies the separate introduction of brine and fresh water into the well at carefully measured and controlled rates and the electrical location of a sharp boundary developed between these fluids. At present this instrument is a research tool of value in determining the effect of various well treatments on an individual sand strata. lts primary use has been on wells in which different sections require different treatments (e.g., wells with an open sand to be plugged and a tight sand to be acidized)- It has, thus, made possible the determination of a rearrangement of the water intake of a well. The instrument can also be used to direct the treating material into a given zone. In completing a well the less permeable sands are shot more heavily with nitroglycerine in order to equalize the water intake between the permeable and less permeable sands. The extent to which such corrective shooting has been successful Can be determined by a water-input profile. The combined profile and well-bore diameters should also provide a method for determining the direction and effect of various selective shooting techniques. Equipment The essentials of the water-input profile technique for measuring the intake per foot of individual sand strata are the injection of a nonconducting fluid, water, at the top of the well and a conducting fluid, brine, through a separate string of

Jan 1, 1948

By Gerhard Derge

Metallurgists have used borax as a fluxing agent traditionally, but until recently elemental boron has played an insignificant role as an alloying element. Neither the metal nor its compounds have been regarded as important metallurgical materials and there is a surprising lack of knowledge concerning their metallurgical behavior. The new applications to steel-making of both boron and borates, which arose in part from wartime incentives and restrictions, have been seriously handicapped by this lack of data. For example, rasorite, a naturally occurring sodium borate, has been shown to be an effective substitute for aluminum as a ladle deoxi-dizer in rimming steels.' Likewise, the effectiveness of boron as an alloying agent has been demonstrated,2,3 giving deep hardening when used in restricted amounts. The exploitation of both of these uses has been retarded by the difficulty of attaining suitable metallurgical control. Recognizing that the most important information required was a knowledge of the equilibrium between boron and oxygen dissolved in liquid iron. Gurry4 calculated this relation from the best thermal data available. However, estimates of the entropy of melting of boron, the activity coefficient of boron in liquid iron and the activity coefficient of B2O3 in slag were involved, and experimental work on this problem was obviously desirable. The experiments to be described were planned to establish the boron-oxygen relations in liquid iron and to demonstrate at the same time the ferroborate slag compositions in equilibrium with various amounts of oxygen in liquid iron. Accordingly, slags containing varying proportions of iron and boron oxides were held in contact with molten iron, and samples of both slag and metal were analyzed. The limitations upon the accuracy of the data will be considered, but in a practical sense the oxygen levels that can be attained in iron by iron borate slags, and the amounts of boron in iron at these oxygen levels were established. Experimental Procedure No entirely suitable refractory was found for the mixtures of iron oxide and boron oxide used as slags. Crucibles of silica, magnesia, Ramix, beryllia, and zirconia were all tried unsuccessfully. The must satisfactory method discovered for handling them was the rotating-crucible technique, which creates a parabolic crucible of liquid iron.5,6 Even this was not entirely successful, for at steelmaking temperatures (1600°C.) the slags had such a low surface tension that they crept up to the refractory and slowly dissolved it. These difficulties made it impossible to maintain a constant slag composition for an unlimited period Of time. However, by using the rotating technique, short runs could be made in

Jan 1, 1947

By Wilbur H. Grant

THE property of the United Comstock Mines Co. lies in the eastern foot-hills of the Sierra Nevada Mountains, in the Washoe mining district of Storey County, Nev. Commencing at the boundary line between Virginia City and Gold Hill, covering all the town of Gold Hill, it extends south to American Flat; the main camp, or the new town of Comstock, the mills, shops, residences of employees, and the main haulage-tunnel portal are located on American Flat. The property extends for about 10,300 ft. along the lode; this covers the southern end of the main Comstock lode, the Knickerbocker branch, and the junction of the Silver City branch with the Comstock lode. Within the property, 5000 ft. of the main Comstock lode is known to have been productive, 1000 ft. of the lode at the northern end of the property is thoroughly developed, and 1000 ft. south of this is partly developed; this leaves about 3000 ft. of the known productive portion that has not been opened up by this company. The northern end of the property, or the Imperial mine, has been intricately developed by five main levels and numerous sublevels. The Yellow Jacket ground to the south has been partly developed by the reopening of three old levels. In addition, the main haulage level is driven from the portal at Comstock for 9250 ft., to the north end of the property; about 5500 ft. of this `is in the foot wall of the lode and parallel to it.

Jan 11, 1922

By Thomas Fraser, H. F. Yancey

BefoRe a new coal-washing plant is installed, or an existing washery is remodelled and improved, considerable experimental work on the coal to be washed should be done. A thorough examination of a coal, to determine whether it can be washed successfully and the best and most economical process for securing a satisfactory grade of washed coal, calls for mine sampling, analytical work, and experimental coal-washing tests which may require several months' time and the expenditure of considerable money. Having collected the required data on the characteristics of the coal and the results secured with different types of machines under different sets of conditions, it is necessary to decide what method of treatment should be used. The interpretation of the experimental data is no small part of the problem. The first step in the investigative work is to determine from the characteristics of the coal and the manner of occurrence of the impurities whether it is possible to separate the dirt from the coal and produce a washed coal of the required quality. Then it is necessary to select the type of washer or the system of treatment that will produce the greatest amount of washed coal of this grade for the least cost. To secure this information, tests may be made at laboratories operated by consulting or contracting engineers, at the testing plants of machinery manufacturers, at commercial washeries, or in an experimental washery erected on the site of the proposed plant. Such tests will produce figures in which every factor, including analyses of raw coal and washed coal and yield of washed coal, may vary widely. To reduce these results to a common basis for comparison is very difficult. A number of plans

Jan 1, 1923

By D. L. Gardner, H. L. Barr

The following report covers the history of the development of the mine, present equipment, methods and costs of mining and milling. In addition, a description of the ore deposit is given with emphasis on the origin of the fractures, mode and types of ore occurrence, and mechanics of granite emplacement. An endeavor has been made to present a complete and accurate statement of the San Mauricio mine, the highest grade gold mine in the Philippine Islands. Credit is gratefully acknowledged to the mine staff for descriptions and details regarding their particular field of work. All analyses were made by Mr. T. A. DeVore, head chemist, San Mauricio Mining Co. Messrs. Edward Wisser, J. E. Fyfe, A. F. Skerl and W. B. Meek, geologists, have contributed geologic information and ideas, for which thanks are extended. The Executive Committee of Marsman and Co., Inc., Managers of the Company, has kindly given permission for publication. Mr. J. B. Stapler, Division Manager, Marsman and Co., has had the courtesy to read the manuscript and to give critical and helpful suggestions. Location of Area and Scope of Work San Mauricio Mining Co. controls a group of 113 claims that lie immediately north of the town of José Pafiganiban (formerly Mambulao), Camarines Norte, Luzon, P. I. (Fig. 1). Exploration work commenced in the spring of 1934; active development began in the fall of that year and has continued to the present date. Mill construction was begun Ocl,. 15, 1935, and production started March 10, 1936. Total production to June 1, 1939, is P10,499,105.15 ($5,249,552.57).

Jan 1, 1941

By V. W. Aubel

Among the iron-bearing ores of the world, the titaniferous iron sands of New Zealand are probably the least known to American engineers. This is not surprising in view of the fact that American ironmasters look with disfavor on any, even domestic, ores containing over 1 per cent. titanium. The possibilities of smelting titanium-bearing ores in the blast furnace are still undetermined, but the problem of their efficient reduction is becoming more important each year. There seems to be little inclination on the part of American furnace operators to tackle this problem, and they will no doubt continue to utilize the non-titanium ores at their command, leaving research and experiment to those countries not so fortunately endowed. New Zealand has, however, been intensely interested in her deposits of titanium-bearing iron sand, and during the last 50 years considerable English and New Zealand capital has been expended on this problem. The extent of the New Zealand iron-sand deposits is almost beyond measure. From Patea north to Manuka Heads, along almost the entire west coast of the North Island, these deposits exist. Wherever there is beach sand along this 300 mi. of coast line, the sand is iron bearing. It varies considerably in grade; but wherever the contour of the coast affords small bays and inlets, large dunes are found that are remarkably uniform in quality. Several of these large deposits, especially those at New Plymouth and Patea, are noted for their high iron content. The dune at New Plymouth runs between 55 and 60 per cent. of metallic iron; the panning action of the prevailing westerly winds and northwesterly currents has no doubt resulted in this concentration. Whatever the origin of this material may be, there is no doubt that deposition is going on continuously. At New Plymouth, a small artificial harbor, protected from the drifting sand by a large breakwall, has been dredged. Here sailing vessels have for years been loaded with iron sand for ballast by means of a crane and grab bucket operated from the wall of the breakwater. Thousands of tons of sand have been removed from this spot yet each succeeding storm renews the supply. The sand dune shown in Fig. 1 has been tested to a depth of 50 ft. (15 m.) without losing its

Jan 1, 1920

By Gerhard Derge

Metallurgists have used borax as a fluxing agent traditionally, but until recently elemental boron has played an insignificant role as an alloying element. Neither the metal nor its compounds have been regarded as important metallurgical materials and there is a surprising lack of knowledge concerning their metallurgical behavior. The new applications to steel-making of both boron and borates, which arose in part from wartime incentives and restrictions, have been seriously handicapped by this lack of data. For example, rasorite, a naturally occurring sodium borate, has been shown to be an effective substitute for aluminum as a ladle deoxi-dizer in rimming steels.' Likewise, the effectiveness of boron as an alloying agent has been demonstrated,2,3 giving deep hardening when used in restricted amounts. The exploitation of both of these uses has been retarded by the difficulty of attaining suitable metallurgical control. Recognizing that the most important information required was a knowledge of the equilibrium between boron and oxygen dissolved in liquid iron. Gurry4 calculated this relation from the best thermal data available. However, estimates of the entropy of melting of boron, the activity coefficient of boron in liquid iron and the activity coefficient of B2O3 in slag were involved, and experimental work on this problem was obviously desirable. The experiments to be described were planned to establish the boron-oxygen relations in liquid iron and to demonstrate at the same time the ferroborate slag compositions in equilibrium with various amounts of oxygen in liquid iron. Accordingly, slags containing varying proportions of iron and boron oxides were held in contact with molten iron, and samples of both slag and metal were analyzed. The limitations upon the accuracy of the data will be considered, but in a practical sense the oxygen levels that can be attained in iron by iron borate slags, and the amounts of boron in iron at these oxygen levels were established. Experimental Procedure No entirely suitable refractory was found for the mixtures of iron oxide and boron oxide used as slags. Crucibles of silica, magnesia, Ramix, beryllia, and zirconia were all tried unsuccessfully. The must satisfactory method discovered for handling them was the rotating-crucible technique, which creates a parabolic crucible of liquid iron.5,6 Even this was not entirely successful, for at steelmaking temperatures (1600°C.) the slags had such a low surface tension that they crept up to the refractory and slowly dissolved it. These difficulties made it impossible to maintain a constant slag composition for an unlimited period Of time. However, by using the rotating technique, short runs could be made in

Jan 1, 1947

By Henry M. Howe

The brilliant and very original matter in Professor Jeffries' discussion† should rank not only as an independent paper, but as a most important one. In particular, the explanation which it gives of the remarkable Sauveur phenomenon, over which so many of us have puzzled long and hard, is so clear, complete, and cogent as to go far toward establishing Professor Jeffries' hypothesis. The very leatures of Professor Sauveur's photographs which fit this hypothesis so exactly are reproduced in Chap-pell's photographs of steel coarsened under somewhat different conditions.' The ideas developed by these discoveries are so novel that convenicnce of language seems to call for new conventional terms for expressing them. In what follows here I propose certain terms for this end, for criticism and improvement, and I attempt to generalize from Professor Jeffries' hypotheses. Generally speaking, a given set of grains which undergo no growth in the cold will, when the temperature is raised progrcssively, start to grow on reaching a certain temperature, and will continue growing at all higher temperatures. The "germinative" temperature is that at which growth begins, quite as the conditions which cause a seed to grow are "germinative." We have then an inert temperature range below the germinative temperature, and a growth range above it, the germinative temperature being the limit between these two ranges. So, too, a germinant grain is one which is at its germinative temperature, and hence beginning to grow, while inert grains are those below their own germinative temperature, and the term "growing grains" includes those which are germinant and those which are above their germinative temperature. These last could be called " supergerminant" if the distinction should be needed. "Germinative temperature" seems better than "critical temperature

Jan 1, 1917

By R. J. Pfister

The development of a water-input profile instrument based on the introduction of brine and fresh water into an input well with the electrical location of, the boundary developed between them is reported. Two methods are available in the use of this instrument to measure the foot by foot water-intake rates of the various sand strata: the moving boundary method in which variable well bore diameters can be determined and/or cancelled out and the constant boundary method. The type of results obtained and the relative advantages of each of these methods are described in detail. Representative data are included covering the use of this instrument in experiments involving selective acidizing, selective plugging, and selective shooting. In such experiments, this instrument has been used to diagnose the unfavorable distribution of water intake in input wells and also to determine the effectiveness of the resultant treatments. The data included also serve to illustrate the type of problems which can be studied with this technique. Introduction For ten years or perhaps longer a number of progressive water-flood operators have felt the need for some to to measure the foot by foot water-intake rates of various strata in water-injection wells. The primary need is to diagnose unfavorable water distribution in various strata and to evaluate the effectiveness of the corrective measures such as selective acidizing, selective plugging, and selective shooting. Previously described methods for obtaining this type of data were not considered entirely adequate.l,2 The profile equipment described in this paper embodies the separate introduction of brine and fresh water into the well at carefully measured and controlled rates and the electrical location of a sharp boundary developed between these fluids. At present this instrument is a research tool of value in determining the effect of various well treatments on an individual sand strata. lts primary use has been on wells in which different sections require different treatments (e.g., wells with an open sand to be plugged and a tight sand to be acidized)- It has, thus, made possible the determination of a rearrangement of the water intake of a well. The instrument can also be used to direct the treating material into a given zone. In completing a well the less permeable sands are shot more heavily with nitroglycerine in order to equalize the water intake between the permeable and less permeable sands. The extent to which such corrective shooting has been successful Can be determined by a water-input profile. The combined profile and well-bore diameters should also provide a method for determining the direction and effect of various selective shooting techniques. Equipment The essentials of the water-input profile technique for measuring the intake per foot of individual sand strata are the injection of a nonconducting fluid, water, at the top of the well and a conducting fluid, brine, through a separate string of

Jan 1, 1948

By S. F. Shaw

The Sierra Mojada mining district is situated in western Coahuila, about 8 km. east of the Chihuahua state line, and about one-half way from the northern to the southern extremity of the state. It is at the terminus of the Mexican Northern R. R., 125 km. northeast of Escal6n, Chihuahua; also about, 240 km. due west of Monclova, Coahuila. The altitude is approximately 1500 m. above sea level. The Sierra Mojada valley is about 10 km. long, from east to west, with a width of 1 to 2 km. It is approached from the east through the Puerto del Oro, where the Mexican Northern R. R. enters the valley; the slope from west to east is gentle. The Sierra Mojada, of which about 300 m. is an almost vertical wall, bounds the valley on the south side; on the north side, the slope to the crest of Sierra Planchada is more gradual, rising only 200 or 300 m. above the valley. Water is relatively scarce in the district, and there are no running streams. The rainy season, usually beginning at the middle of June, lasts through July, and occasionally into August or September. In some years the rains fail entirely. The slope of the ground is such that nearly all the water immediately runs off. The arroyos along the flanks of the mountains are not very deep, but in heavy rains, sometimes approaching cloudbursts, a tremendous volume of water rushes down them, carrying large boulders. A certain amount of seepage collects in the agglomerate, lying below the conglomerate, and is retained in the local fractures. Some shallow wells have been sunk in this agglomerate, and one well over 150 m. deep was sunk on the Volcan ranch, supplying about 76 1. (20 gal.) per min. A considerable supply of water is collected in large earth reservoirs in and below the town of Esmeralda. In ordinary years this supply will last until January or February, after which the Volcan well has to be depended on until the next rainy season. Vegetation is scarce, aside from scanty scrub oak and other brush in the mountains, and a few mezquite, locust, pepper, and cottonwood trees

Jan 1, 1923

By Persifor Frazer

The '(author's edition" of the following paper, "subject to re vision," was received by him, and copies sent to Professor Geikie and others about two weeks before the date of the meeting at which it was to be read. A telegram, and subsequently a letter (both of which unfortunately arrived too late), apprised the present writer that the Director General objected to certain views ascribed to him as the reverse of those which he really held. These views, however interesting, had no very important bearing on the object of the fol lowing notes, which, as must be evident, are devoted to the conside ration of the close analogies between the Welsh and American rocks. Without being able, therefore, to account for the circumstance which Professor Geikie has mentioned, it is thought better in the present revised edition to omit all allusion to Professor Geikie, or Mr. Peach, or their views, except in this place, where I desire to thank them for their courtesy during the time which I had the pleasure of spending in their society. It appears sufficiently throughout the body of the paper that the writer had not the slightest intention of entering the controversy, which was about to commence, concerning the proper horizons of the St. David's rocks, for many reasons; and amongst others because he did not feel that a sojourn of a few days in a difficult region, which had been already studied by many of the foremost geologists of England, would warrant him in adding to the literature on the sub ject. The discussion of the analogies between these rocks and those of the Eastern Appalachians, which he has studied for twelve years, of which eight were spent in the service of the Second Geological Survey of Pennsylvania, was much more to his taste as it was more within his ability, and if he has added anything to the evidence of these analogies, the paper, however imperfect, will not have been written entirely in vain. Right or wrong, he assumes the entire responsibility of what follows.

Jan 1, 1883

For four years your Committee has been engaged in the study of problems connected with the educational preparation of professional geophysicists. The Present report represents the conclusions drawn from the investigations and deliberations undertaken since it was first organized. These studies have shown that the evolution of geophysics has proceeded along lines that differed from those marking the advance of classical geology. The latter science developed as a descriptive one, dealing with directly observable terrestrial phenomena, and the elementary, rational explanations that could be offered therefor. The fact that these phenomena were also chemical and physical in nature was seldom given more than passing acknowledgment. During the last half century, however, a new approach to problems of terrestrial phenomena has become of greater significance. This new attack has come through the sciences of physics and chemistry, as the people trained therein have investigated the facts of the earth as problems in their respective sciences. This development has been chiefly at the hands of European investigators, and European universities have long recognized it by establishing departments or institutions of geophysics. In the universities of North America, their arbitrary departmentalization into fields of physics, chemistry, astronomy, geology, etc., has prevented the academic recognition of such domains of science as geophysics and geochemistry. In consequence, the development of these subjects in the United States has been largely at the hands of nonacademic institutions, while the universities themselves are evidently in a state of confusion as to how the subject should be handled. In some places an attempt to teach geophysics is made in the physics department, in others in the geology department, in some in the engineering school, and occasionally as a cooperative effort; a Department of Geophysics is seldom found in North America. In some instances, proper academic plan. ning has been precluded by interdepart. mental jealousies, or by lack of appreciation of the significance of the subject. For the background upon which these conclusions are based, the reader is referred to reports previously issued or SPonsored by Your Committee. The "First Report of the A.I.M.E. Mineral Industry Education Division's Committee of Geophysics Education, 1939," summarizes the replies received to question-

Jan 1, 1946

By P. V. Roundy, G. R. Mansfield

Public lands in Florida were first withdrawn from entry by President Taft on July 2, 1910, as a conservation measure because of their possible phosphate content. The reserve thus established was subsequently modified by further withdrawals and by restorations, so that on Jan. 1, 1934, it contained 66,796 acres, of which only a small part had been definitely classified. The reserved land was in scattered parcels, ranging from less than 40 acres to 320 or more, distributed in many counties. For administrative purposes and for final disposal of any of the numerous parcels, mineral classification of the land is legally necessary. In 1934 and 1935 the United States Geological Survey, under two successive grants from the Public Works Administration, prospected some 83 tracts of these lands in Polk County, comprising in all about 3300 acres, and six tracts comprising 240 acres in Citrus and Marion Counties. The tracts in Polk County were all in the so-called land-pebble field and the others in the hard-rock field. The Survey field party was under the direction of P. V. Roundy, from whose unpublished report the material in this paper is largely taken. The foreman of the prospecting crew was J. H. Wingate of Zephyrhills, Fla. The individual tracts were identified through the cooperation of the General Land Office, by transitman Hugh B. Crawford. This prospecting work fitted well the classification adopted for Public Works projects in general: it could not be done on any considerable scale under the Survey's usual appropriations; it gave employment to unemployed labor; and it may be expected ultimately to repay the Government in royalties more than the cost of the exploration. Commercial, Prospecting Methods Commercial methods of prospeeting for phosphate in Florida have been briefly described by Mansfield.' In the hard-rock field, where the floor of the phosphate deposit is extremely irregular, it is customary to drill a.:

Jan 1, 1938

By Arvid E. Anderson, Frank K. Cameron

The weathering of copper-bearing ores with the formation of a water soluble salt and the recovery of the metal by leaching and evaporation precipitation, are processes long known, which have at various times been utilized with more or less commercial success. It is commonly assumed that the technical principles involved are quite simple and their application to a particular case easy. If these assumptions were true, we should anticipate a long list of uniformly successful leaching operations, which is not the case, and one would be justified only in calling attention to either unique or peculiar features of any particular enterprise; whereas, in studying the problems of the recovery of copper from the old workings of the Ohio Copper Co. in the light of available descriptions of other leaching projects, we have not found the assistance hoped for to guide us to the best realization of our own opportunities. It appears desirable, therefore, to call attention to these guiding principles, together with a description of the facts of accomplishment. Justification lies in the fact that the leaching and precipitation of copper at the Ohio Copper Co. mine in Bingham Canyon, Utah, is successful. This success is measured by an average monthly production of 600,000 Ib. of copper at an average operating cost, to date, of 3.85 cents per pound at the company's workings, or 6.32 cents per pound after paying shipping and smelter charges on the finished copper. A total of 17,076,099 Ib. of copper had been shipped to the smelter from the beginning of operations, August, 1922, to April 1, 1925. Probably these results can be bettered with further study and realization of the factors involved and the devising of methods of meeting them. It is now an assured fact that the enterprise will have a relatively long and continuously profitable life and that its reserves will not, nor cannot, be suddenly and permanently depleted. It is particularly noteworthy that the financing of this enterprise has been entirely from its earnings. The few hundred dollars necessary for the first experiments and production were obtained by the sale of used, and no longer needed, equipment from a mill belonging to the company; and all funds since required throughout the growth and development of the enterprise, from a few troughs with a production of 2000

Jan 1, 1926

By K. B. Nowels

DATA pertaining to pipe line flow for both oil and gas in horizontal or nearly horizontal pipe lines are both extensive and accurate. However, the pipe formulas used to determine pressure drop for flowing fluids (liquids and gases) under conditions of horizontal flow are not generally applicable to flowing oil and/or gas wells. Except for some data developed in small laboratory set-ups, little or no information was available concerning flow of oil and gas mixtures in vertical pipes, when, in 1928, the writer began the development of a method for computing pressure drops in the pipes of flowing oil wells, as outlined in this paper. In 1929, Uren1 presented some findings based on laboratory experi-ments in which vertical flow of an extremely heavy crude oil was induced, by means of air through a 2-in. pipe, 41 ft. long. The friction factors derived from the experiment, as well as values for pressure drop per 100 ft., are not believed satisfactory in their application to flow problems in the field. Versluys,2 also in 1929, presented a mathematical development of the theory of flowing oil wells, and in 1930, gave a companion paper3 setting forth some principles governing the choice of length and diameter of tubing in oil wells. Since the termination of the study presented in this paper, another. valuable contribution pertaining to the problem, of vertical flow was made by Moore and Wilde.4 Although there were writings dealing with the principles of the gas-lift, a search of the available literature indicated that specific information on vertical flow was lacking with the exception of the writings of Uren, Versluys, and Moore and Wilde, to which reference .has been made.

Jan 1, 1932

By C. D. Woodward

PRIOR to 1902, the tramming of ore from the stopes to the shafts, in the Butte mines, was done by man or animal power, but the demand for greater tonnage and the need for more improved methods of tramming the ore resulted in the installation of the compressed-air locomotive in a few mines. Some of the objections to animal haulage were thus eliminated, but this locomotive was not generally adopted, because of a number of limiting features. It was superseded by the electric trolley locomotive. The early types of trolley locomotives were not satisfactory from the operators' viewpoint, but. they had many economic advantages and after a number of years, in which improvements were constantly made in the structural details, they became dependable, so that the use of animals for main haulage in the mines has now been practically abandoned. There are now operating in the Butte mines of the Anaconda Copper Mining Co., 185 trolley-type locomotives, each of which has replaced five animals. It cost approximately $50 per month to keep an animal, hence the economies that resulted fully justified the expenditure of electrifying the haulage systems. The haulage conditions in this company's mines possess many advantageous features that are not always found in underground mine workings. The drifts and crosscuts are large, approximately 5 ft. (1.5 m.) wide by 7 ½ ft. (2.3 m.) high, and have curves of no less than 18 ft. (5.5 m.) radius; and the roadbeds of the drifts and crosscuts have a uniform grade of 0.5 per cent. toward the shaft, or in favor of the loaded trips. In all of the mines, except two, the track gage is 18 in. (45.7 cm.), and all tracks in the main haulageways are laid with 25-lb. (11.3 kg.) rails. The stations at the shaft are large, well-lighted, clean, and cool. The average temperature of ,the stations, however, is about 75° F. (24° C.), while the average temperature in some of the drifts and crosscuts is 92° F. (33.5° C.).

Jan 2, 1922

By O. George Specht, Carl A. Zapffe

IN recent print, some remarkably contradictory statements have appeared regarding the importance to be attached to sponge iron,1-6 a metallurgical commodity whose history goes back at least to the time of Diodorus Siculus in the fourth century B.C. This disagreement, however, expresses the lack of a satisfactory method for producing sponge iron rather than defection in the commodity. The blast furnace is admitted to have certain inherent disadvantages, such as a general unsuitability for magnetite and the heating and blowing of vast quantities of undesirable nitrogen, so that a workable sponge-iron process remains attractive. In this respect, low-temperature gaseous reduction shows especial promise; but confusion persists regarding the factors involved. The present paper, therefore, has three principal divisions: (I) an exhaustive examination of all previous work on low-temperature gaseous reduction, (2) experimentation on the reduction of a magnetite with hydrogen, and (3) development of certain thermodynamic relationships in reduction, with a summarized depiction of the factors in the general process. PREVIOUS INVESTIGATIONS Gaseous media used in the reduction processes under discussion can be classified in three types: (I) H2, (2) CO, and (3) other gases. In the second, the CO is often admixed with H2. The third principally comprises hydrogeniferous gases, such as natural gas and producer gas, and in addition includes chlorine. Because hydrogen therefore features in all three, a study of hydrogen reduction based on investigations using pure hydrogen alone may be incomplete. The present paper reviews the three groups of investigations in the listed order, paying particular attention to hydrogen reduction. For the benefit of future workers, an exhaustive bibliography has been prepared and similarly classified. GROUP I: REDUCTION WITH HYDROGEN Equilibria Although the present problem is specifically one of kinetics, a first consideration is the equilibrium of the system, since the reactions to be studied comprise that equilibrium, and their direction and end points are defined by it. The historic development of these researches is interesting and informative.

Jan 1, 1946

By Henry N. McCarl

Lightweight aggregates include a variety of mineral and rock materials used to provide bulk in concrete building units (block), light- weight structural concrete, and precast concrete units, as plaster aggregate, insulating fill, and other structural and/or insulation purposes. They are distinguished from other mineral aggregate materials by their lighter unit weight- 80 to 100 pounds per cubic foot (pcf) or less for loosely packed lightweight aggregates as compared to 125 pcf or more for crushed stone, sand, gravel, air-cooled slag, and other more common mineral aggregates. The various lightweight aggregate materials may be classified into four groups as follows: 1) Natural Lightweight Aggregate Materials-prepared by crushing and sizing natural rock materials such as pumice, scoria, tuff, breccia, and volcanic cinders. 2) Manufactured Structural Lightweight Aggregates-prepared by pyroprocessing clay, shale, or slate in rotary kilns or on traveling grate sintering machines. 3) Byproduct Lightweight Aggregates-prepared by crushing and sizing foamed and granulated slag, cinders, and coke breeze. With the exception of processed slag, this group is becoming less important as time passes. 4) Manufactured Insulating Ultralight- weight Aggregates-prepared by pyroprocessing ground vermiculite or perlite. This chapter will focus on the use of natural lightweight aggregates and manufactured insulating ultralightweight aggregates, and both the production and use of manufactured structural lightweight aggregates with some comments on byproduct materials. Detailed discussion of the production and use of both expanded and air-cooled slag is presented in a separate chapter in the utilization section of this volume, and there are separate commodity chapters on vermiculite, perlite, pumice, and volcanic cinders. Discussion of the commodities covered elsewhere in the book will be limited to observations on their utilization and relation to other lightweight aggregate materials. All materials considered as lightweight aggregates are derived from some initial natural raw material. While historical definitions have included such organic materials as straw and peat as lightweight aggregates, the discussion in this chapter will restrict itself to lightweight aggregates derived from mineral or rock materials. Thus while the actual lightweight material in use may be a manufactured product, it is derived from an ore or raw material that is obviously a mineral resource. In this context, then, the reserves of raw materials for lightweight aggregate use may include iron ore and flux stone (the components of blast furnace slag) as well as coal (the raw material from which cinders are derived) as well as those clay, shale, and slate deposits that display the characteristics of bloating or controlled expansion when subjected to elevated temperatures (1600 to 2400°F.).

Jan 1, 1975

By Simon Ash

THE coal-mining districts of Washington are mainly west of the Cascade Mountains; Fig. 1. The mines are on the foot hills of the slope, the lignite fields of Lewis and Thurston counties extending into the valleys west of the mountains. An exception is the Roslyn field, a small but important area on the eastern slope. If western Washington is divided into three areas from north to south, the bituminous coal fields and most of the active operations will be found largely in the middle area. The southern portion contains lignites over a large area. In the northern portion, mining is practically restricted to one mine, the Bellingham, which is working a subbituminous coal seam near the city of Bellingham. The degree of alteration that the coal of a particular field has undergone may be gaged roughly by the position of the field with reference to the Cascade Mountains. The lignites of Tenino, Tono, Mendota, and Castle Rock, on the railway line connecting Seattle and Portland, occur in a region, of low relief, in which the Eocene coal measures have suffered only minor disturbances. Subbituminous coals occur in the foot hills, as at Renton, Newcastle, and Bellingham. Coals high in fixed, carbon are found nearer the mountains, where. the measures have been sharply ,tilted and folded, as at Black Diamond and Carbonado. The two typical anthracite fields are located still higher, in the rugged mountains where outcrops appear both in deep gorges and on ridges at elevations approaching 5000 ft. At. Carbonado is found the only semianthracite seam worked on a commercial basis. The occurrence of this seam in a region of bituminous coal is due to the nearness of an igneous sill, which has changed its character from bituminous to semianthracite.

Jan 3, 1925

By E. L. Jr. Spain

THE deposits described in this paper occur over much of Wayne County and in the southeast portion of Hardin County, Tennessee, and in the northeast and northwest portions of. Mississippi and Alabama respec-tively. The presence of tripoli in this region has been known for some time and descriptions of various occurrences in Tennessee have been made by Jewell1 and Miser2, while Hilgard3, Lowe4 and Logan5 have treated the deposits that occur in the adjacent portions of Alabama and Mississippi, but there has not been a general survey of the entire field summarizing completely the geology of the deposits with respect to their origin and stratigraphic relationships. During 1934, while engaged in surveys of mineral resources through this region for the Tennessee Valley Authority, the writer collected data with this in mind, and has assembled them in this report. He is indebted to H. S. Rankin and N. A. Rose, of the Tennessee Valley Authority Geology Division, for field assistance.

Jan 1, 1936