Search Documents

By Kenneth Cotingham

Many factors joined in reducing drilling activity in Ohio in 1942. Conservation Order M-68 was important, but other things, such as operators and members of drilling crews joining the armed services and going into war plants, had an important part. The reduction in number of completions was considerable. In 1941, the total of wells drilled was 1561 but in 1942 the total was 1008. The total initial daily open flow discovered by the 701 gas wells drilled in 1941 was 492,000 M cu. ft., whereas the open flow of the 471 gas wells completed in 1942 was 314,488 M cu. ft. The total initial daily production of the 333 oil wells drilled in 1941 was 10,300 bbl., and in 1942 the 181 oil wells had a total daily initial of 7570 bbl. The average daily initial per gas well therefore was somewhat less in 1942 when compared with the preceding year, but the initial per ail well increased about 36 per cent over 1941. General Activity The total depth of the 652 oil and gas wells drilled in 1942 was 1,597,000 ft. The most active county was Perry, where 63 oil wells were drilled, most of them in Clayton township. In Morgan County. where 43 gas wells were drilled, the greatest activity was in York and Marion townships. Medina County was third in number of wells drilled, although of the total of 33 gas wells in the county, 26 were in the new Hinckley township pool. The total initial open flow of these 26 wells was 39,202 M CU. ft., and was considerably larger than from any other single area. Muskingum was an active county, particularly Washington and Wayne townships, in each of which seven gas wells were drilled, and Blue Rock and Harrison townships, in each of which five gas wells were drilled.

Jan 1, 1943

By T. F. Witherbee

THE Fletcherville Furnace was built in 1864 and 1865, making its first blast from August until October of the latter year, when it was blown out to prevent its "bunging-up." Repairs were made in time to enable it to be blown in again December 12th, 1865, the blast ending October 7th, 1866. Total product 1921.15 tons iron, an average of 6.8.2.5 tons per day, from ores yielding 44.8 per cent. Consumption of charcoal 223.2 bushels per ton of iron. The furnace journal up to this time shows no record of furnace dimen¬sions, or temperature of the blast, but as near as can be ascertained, they were as follows, viz. Height of stack, 42 feet. Diameter of bosh, 11 feet. Angle of bosh, 7 1/2 inches to 12 inches rise, about 58°. Diameter of open tunnel head, 42 inches. Number of tuyeres 3; each 3 inches in diameter. Dam 15 inches high. Tuyeres 24 inches high. Tymp 22 1/2 inches high. Diameter of steam cylinder, 20 1/4 inches. Stroke 5 feet. Diameter of blast cylinder, 64 inches. The engine is direct-acting horizontal non-condensing. December 26th, 1.866, the furnace was again put in blast, having been considerably altered in the crucible; the height of stack, bosh, and tunnel head remaining as before. Six tuyeres were put in, three in each of the side arches. The hearth or crucible was rectangular in form, 3 feet wide x 32 feet long x 62 feet high. Inclination of bosh 58°. Height of tuyeres 26 inches ; nozzles 2 1/4 inches diameter. Temperature of blast estimated to be about 500°.

Jan 1, 1874

By C. C. Harris

An analytical solution of the integro-differential equation of batch grinding is proposed as a first appoximation to the xYt surface. The size distribution equation (xY plane) is a three parameter equation previously suggested. Possible refinements are outlined. Comminution kinetics research is presently following several related courses. Some are equivalent, in that they represent different ways of viewing the same facet of the problem, though the entire endeavor cannot be described as being completely integrated. The purpose of this note is to propose and discuss a framework into which the various approaches might be fitted. This must clearly be founded upon an analysis of the xYt surface.' (See also Fig. 1 of Reference 26.) The investigations referred to above comprise mainly researches into the following: (1) The kinetics of the creation of the finer sizes during relatively small grinding times. This is the Fahrenwald-Arbiter-Bhrany 2-3 approach which leads to equations equivalent to a special case of the charles4 relationship. It emerges that initial production of fines follow essentially zero order* kinetics. (2) Disappearance kinetics of the coarser fractions. This appears to be a first order relationship.5-6 (3) Prediction of the xYt surface via the selection and breakage functions utilizing computer-programmed or approximate solutions of the integro-differential equation of batch grinding.5,8-17 A recent discussion by Mika et al.5 references the relevant literature up to about 1966. In addition to these main-stream researches there is some work on the minor topic of extremely long grinding time considered as a limiting case.18-19 The field is supported by investigations into the size distribution of fragments produced by breakage processes, some of this work being most valuably statistical-mechanical in nature.20-25 Better fitting equations, however, are obtained by statistical and curve-fitting methods.26 This

Jan 1, 1969

By E. P. Abrahamson II

The effect of transition elements which form binary solid solution upon the recrystallization temperature of zirconium has been investigated. All additions raised the recrystallization temperature. A correlation is obtained between the logarithm of the rate of change of recrystallization temperature with atomic percent solute and the free atom ground state electron configuration of the solute element. ThE work of Abrahamson, et al., on dilute binary solid-solution alloys indicated a correlation between the free-atom ground state electron configuration of the solute and either the brittle-ductile transition or recrystallization temperature. These studies were carried out on bcc base materials. The implication is that the outer s and d electrons of the solute are the prime determinant of the absolute rate of change of recrystallization or transition temperature. Furthermore, the limit of linearity has been shown to be a function of solute electron configuration for recrystallization in iron and vanadium. To date no Complete systematic recrystallization study of dilute binary zirconium base alloys has been made. It is the purpose of this study to note whether the change in solvent structure from bcc to hcp will influence the correlation. It was also desired to learn more of the role of the electron configuration of the solvent on recrystallization temperature. PROCEDURE All alloys were made using 99.87 pct Zr with 0.01 Cr, 0.04 Fe, 0.006 Hf, 0.003 Mg, 0.003 Mn, 0.003 N, and 0.080 0 (132 BHN). The solute elements were 99.9 pct pure. According to the published binary phase diagrams6 and metallographic examinations at X750, all alloys used were solid solutions. The alloys were arc melted and remelted six times in the form of cubic 200-g buttons under an argon atmosphere. They were then hot pressed at 950°C to 0.450 in., upset pressed to 0.350 in., and annealed at 800°C for 1 hr. The specimens were then Blanchard ground to 0.250 in., removing 0.050 in. from each side. The grain size of the material at this stage was found to be 8000 100 grains per sq mm. The specimens were then cold rolled to 0.130 in. and cold pressed to 0.125 in., yielding 50 1 pct cold work. All alloys were then chemically analyzed for the principal addition. The interstitial contents remained at the values of the starting material when checked on random alloy specimens. The rolled sheet was cut into 6.75 by 0.25-in. lengths and heat treated in a gradient furnace for 1 hr. The gradient was 250o to 900°C over the 6-in. length, recorded continuously by six thermocouples resting on each specimen. Control was 3oC, accomplished at the hot end. The recrystallization temperature was determined metallographically using polarized light. The criterion chosen was the point on the specimen showing the first recrystallized grain at a constant magnification, X200. Specimens were repeated, and the agreement was found to be 3°C. RESULTS Three different pure zirconium specimens were tested, and the recrystallization temperature was

Jan 1, 1962

An index covering the papers presented at the 19 Open Hearth Conferences from the first meeting at Pittsburgh, April 15 and 16, 1925, through the most recent meeting in Detroit, April 16 and 17, 1936, the reports of the meetings and the discussions that took place has been published, accompanied by a list of the papers presented, grouped by subject matter and a list of books of interest to open hearth men The list below gives the Open Hearth Conference meetings in chronological order and the symbols used to designate them in the index SYMBOL MEETINGS P25 Pittsburgh, April 15 and 16, 1925 C125 Cleveland, Oct 13 to 15, 1925 Ch26 Chicago, April 12 and 13, 1926 P26 Pittsburgh, October, 1926 B27 Buffalo, May 3 to 5, 1927 D27 Detroit, Nov 2 and 3, 1927 Y28 Youngstown, May 3 and 4, 1928 P28 Pittsburgh, Nov 15 and 16, 1928 C129 Cleveland, May 16 and 17, 1929 Ch29 Chicago, Nov 5 and 6, 1929 B30 Buffalo, May 20 and 21, 1930 C130 Cleveland, Nov 20 and 21, 1930 Ch31 Chicago, May 12 and 13, 1931- D31 Detroit, Nov 24 and 25, 1931 P32 Pittsburgh, May 24 and 25, 1932 Ch33 Chicago, June 29 and 30, 1933 P34 Pittsburgh, June 28 and 29, 1934 C135 Cincinnati, April 11 and 12, 1935 D36 Detroit, April 16 and 17, 1936 The list of papers mentioned in the first paragraph above is reprinted on pages 428 to 431 The Index of the Open Hearth Proceedings may be purchased at A I M E headquarters, 29 W 39th St, New York

Jan 1, 1936

By L. P. Durham

DuRing the early mine development period, 1929 and the first part of 1930, a 300-ton pilot-plant concentrator was built at Nkana mine of the Rhokana Corporation, Northern Rhodesia. This plant operated from May 26, 1930 until Oct. 26, 1931, treating 101,080 tons of Nkana ores and producing 4372 tons of concentrate. The plant was built, primarily, as a test unit to determine the grinding characteristics, floatability, etc. of the Nkana ores and other ores of the Rhodesian copper belt and to supply sufficient data on which to base the design of a 5000-ton concentrating plant at Nkana mine. The test unit operated wholly on development ores and no attempt was made to grade or select the ores from any section of the mine. The average assays for the 17 months of operation are given in Table 1. The first ground was broken for the 5000-ton concentrator during June, 1930, and the construction of the plant was completed in November, 1931. The plant started on Dec. 10 and has operated continuously since that date: The whole of the concentrating plant is compact and closely connected, yet with sufficient space for expansion of all sections up to 20,000 to 25,000 tons per day capacity. Mining operations are carried on along a length of about four miles on the easterly limb of the Nkana syncline. This length includes the North orebody, from which all production has thus far originated, and the Mindola orebody, now being developed for production. The ore-bearing measures in the North orebody are leached for some 75 ft. below the surface; the oxidized zone varies in vertical extent from 100 to 150 ft. Practically all the ore below the 200-ft. level is sufficiently

Jan 1, 1935

By R. H. Richards, A. E. Woodward

In Rittinger's Aufbereitungskunde of 1867 occurs (p. 195) the following table, which shows the rate of falling in water of fragments of minerals, of irregular shapes and of five different specific gravities: Diameter of particles in millimeters. 10 8 6 4 3 2 1 .5 Sp. Or. Velocity in meters per second. Auriferous silver, 16..9 .8 .7 .57 .5 .4 .29 .20 Galena,. ..7.5 .62 .55 .48 .39 54 .28 .20 .14 Pyrites,. ..5.0 .49 .43 .38 .30 .26 .22 .15 .10 Quartz,. ..2.6 -30 .27 24 .19 .17 .14 .10 .07 Coal,. ..1.3 .13 .12 .10 .08 .07 .06 .04 .03 With the purpose of extending this valuable table, to cover a larger number of minerals and sizes of each mineral, and of making it more easy of application in deciding upon a sieve-scale for any group of minerals, we have prepared the curves of velocity of fall of bodies in water shown in Plates I., XI., 111. and IV., using Rittinger's formula V= 2.44d(8 —1) where V= velocity in millimeters per second. " D = diameter of particles in meters. " 8 = specific gravity of the mineral. These curves embrace a large number of specific gravities, and for each specific gravity the relation of the diameter of the mineral particle to the velocity of its fall in water is given for all diameters and velocities used in practice. The second diagram is an enlargement of the lower left-hand corner of the first, the third bears the same relation to the second, and in like manner the fourth to the third. Plate I, therefore, covers the work of the coarsest jigging 2 inches in diameter; and under

Jan 1, 1890

By M. M. Singh, J. W. Brown

Three rocks of highly varied physical properties are selected for the first reported experimental study concerning microseismic activity of rock under tension to determine the effects of static fatigue, loading rate, repeated loading and rock anistropy compared to compression and bending loads. The microseismic method of detecting rock under deformation may be a great potential tool in surveillance and location in situ of dangerously stressed strata, as well as predicting rock failures. Noises emitted under load or the rate of energy (energy of noise pulses generated per unit time) are computed for varying conditions. The tests are conducted at constant load on a dead weight loading machine to eliminate all possible extraneous noises — an indispensable precaution — at various load levels. Experimental results are reported including the relation of total energy emitted to tensile strength of rock and the possibility of simulating a phenomenological model for microseismic activity. Plots of some of the experiments are included. INTRODUCTION Rock failure, whether on a large scale faulting in the earth's crust and rock bursts in mines, or on small scale ruptures of laboratory test specimens, generates transient vibrations in the rock mass. Mechanisms of intermittent deformation, such as twinning and cracking through and between mineral grains, also produce similar vibrations, but of very small amplitude. Such vibrations from both deformation and failure are referred to as microseismic activity, rock noise, or occasionally seismo-acoustical activity. An individual rock noise is sometimes

Jan 1, 1967

Jan 1, 1971

By R. C. Neavel

One of the most important requirements to be met by any coal producer is delivery of size consists tailored to specific applications. Generally these specifications include a minimum as well as a maximum size limit. The customers of a major Indiana coal producer noticed that some shipments of sized coal contained a large proportion of undersize pieces. Also, in these shipments, the pieces which remained within the specified limits were cracked and, when handled, crumbled readily. The producer, certain that these shipments had been properly sized at the tipple, suspected that degradation had occurred in transit. The Indiana Geological Survey was requested to examine the coal from one of these shipments to attempt to determine the cause of breakage. Two basic facts about coal and coal seams led to the employment of petrographic techniques in this investigation. First, all coal seams consist of accumulations of diverse organic and inorganic constituents; and second, most coal breakage, either desirable or undesirable, can be attributed to the inherent weakness of some of these constituents or to poor adhesion between certain constituents. Analyses of degraded coal Sampling: Samples were secured from 2 stock piles of 2-by 4-inch coal in a dealer's yard. The coal in both piles had received the same treatment from mining to storage, although it had been mined and shipped on two different days. The size consist of one pile, however, appeared smaller than that of the other. The sample from the degraded pile is referred to as the slack sample, and the other is called the unslack sample. Size analyses: In order to determine the actual size consist, the samples were screened, with a minimum of rough handling, on square 2-inch, 1-inch, 1/2-inch, and 12-mesh screens. It is assumed that 100 percent of the 2-by 4-inch coal is retained on a 2-inch round screen at the tipple. Analyses of several loads at the tipple indicate that approximately 26 percent of the 2- by 4-inch coal, 100 percent of which was assumed held on a 2-inch round screen, passed through a 2-inch square screen. Twenty-six percent may be taken as the normal difference between round and square screens. Results of the analyses of stockpile coal are shown in Table 1. Cumulative percent versus size are plotted on a Rosin-Rammler chart as Figure 1. Both samples approximately follow normal size distribution; this indicates that breakage is not size preferential and also that the samples are representative of the stockpiles. Although both samples exhibit the same general size distribution, the median size of the slack sample is considerably smaller than that of the unslack sample. Fifty-five percent of the unslack sample was undersize (29 percent greater than the normal 26 percent difference), and 83 percent of the slack sample was undersize (57 percent greater than the normal 26 percent difference). Both piles contained a greater percentage than normal of undersize coal; this indicates that they were both affected by degradation, but to a different degree. Bedding-plane analyses: Coal, because of its laminated nature, will break preferentially along bedding planes, especially where adjacent constituents are poorly cemented to each other. Subsequent breakage perpendicular to the

Jan 1, 1961

By R. S. Olson

An analysis of the wash thickener-two stage filtration circuit was undertaken to quantitatively describe the circuit performance. On the basis of information developed in this study, the factors of major importance in reducing soluble loss are: filter wash, wash zone size, filter capacity, filter feed pulp dilution, blow back, filter cloth, water to repulp, water to primary wash, water to feed pulp and thickener underflow. The wash thickener-two stage filtration circuit has been used in many hydrometallurgical plants to separate solute from leach solids. As many as 20 to 30 plant operating variables determine the performance of the wash circuit and hence the soluble loss. The complex relationships of these variables, with each other and with soluble loss, make the evaluation of their effect on mill performance difficult. An analysis of this type of circuit was undertaken to quantitatively describe the circuit performance. THE CIRCUIT The diagram in Fig. 1 represents the operation of the wash thickener-two stage filter circuit. This circuit provides for counter current, cross current or for a combination of countercurrent-cross current operation. The feed pulp stream, J, is intended to include any solution or water, other than primary and secondary filtrate, which enters the wash thickener. Except for filter washing, the operations in the circuit are simple mixing operations which can be described by material balance. The concentration of solute in the filtrate and cake solution after application of wash liquor cannot be described by simple material balance. The displacement washing equation, derived by Rhodes1 and extended by Choundhury and Dahlstrom,2 appears to best describe this case of miscible displacement in porous media. In a useful form, it is

Jan 1, 1963

By E. T. Turkdogan

Jan 1, 1962

George E. Collins, Nacoochee, Ga. (communication to the Secretary): The results tabulated below were obtained at the Reynolds mill, White county, Ga. They were noted, not with a view to investigating the point discussed by Mr. Clark, but in course of a test on a working scale to determine the com parative saving from a given free-milling ore on copper and silvered plates respectively. In every case the bullion assayed was the result of a separate clean-up on a considerable quantity of ore. The ore varied widely in grade and in other respects, but the runs bracketed in the table were made at the same time, in adjoining batteries, and on similar types of ore. In a * Result modified by the addition to the bullion-shipment of a little impure bullion left over from previous clean-ups.. On these occasions, the strips of copper were removed from the tables, and: their lower surfaces were cleaned. Hence the higher yield reported.

Jan 1, 1900

By P. T. Allsman

INTRODUCTION The honor of being the recipient of the Mining Society's Daniel C. Jackling Award for 1966 imposes on me the responsibility to search for the subject that I would be best qualified to discuss. It seems that my experience in the mineral industry — nearly 15 years in private and 30 years in public employment — should uniquely qualify me to comment upon the relationships between the mining industry, mineral engineering as a profession, and government, and the changing economic, technologic, political and social changes that dictate their relationships. Such conditions, the increasing knowledge of the world mineral resource base, the greater demands of an expanding population with a rising standard of living, shall be evaluated with respect to our profession — mineral engineering. In all of these forty or so years, I have been in close touch with many phases of the mineral and energy resource industries, especially those of the United States. Particularly during the past 10 years, I have had a ringside seat at the "goings on" in Washington. During all of this period I have observed and analyzed many of the problems of the industry and its relations with the government. During the past few years, I have had increased opportunity for doing research and have found a need to learn something about the mathematical techniques that are undergoing such a revival since electronic computers were developed. One of these techniques is multivariate analysis, which is a system for correlating a large number of complex variables. By applying this technique to the seemingly chaotic present-day situation, there emerges a course of steady improvement in the minerals resource industries that wars, depressions, and political strife have failed to obstruct for long. In short, I advocate a need for new concepts in mineral engineering to cope with the changes, pos- sibly adding many more specialized areas on one end of the spectrum, and broad engineer-generalist approaches at the other. The meeting place shall be where the intricate mineral resource problems at the frontier of knowledge merge into the socio-techno-logical problems of the world. HISTORICAL INVOLVEMENT OF GOVERNMENT IN MINERAL RESOURCE PROBLEMS Involvement of government in mineral resource problems undoubtedly is as old as government itself. But passage of the Mining Act of 1866, superseded by the Act of 1872, was the first major entry of our Federal Government into the problems of mining. Passage of the law was necessary to resolve many conflicting claims and disputes in mining. The General Mining Law of 1872 and the Mineral Leasing Laws of 1920 apply to millions of acres of public lands and to certain privately owned land on which the mineral rights have been reserved to the Federal Government. The extensive involvement of government in the mineral industry business today often comes as a shock to the mineral engineer who has begun to climb the ladder to the top in his company. He is often poorly prepared to cope with the situation and becomes frustrated and even hostile. Better knowledge of the role of government perhaps would ease his situation. In our political system, private industry is responsible for producing minerals. To make certain that the production is adequate for a peace-time economy, and to guarantee the Nation's security in an emergency, the Federal Government finds it expedient to develop policy and engage in regulatory, educational, and research activities. A few examples will illustrate the varied role of government in relation to mineral problems. In varying degrees many agencies of the Executive Branch of Government have responsibilities that influence the functioning of the mineral and energy industries. In addition, of course, Congress, the Judiciary, and State and local governments exercise great influence. The Department of the Interior is primarily responsible for activities to promote the development and conservation of mineral and fuel resources, and the

Jan 1, 1967

By Jack F. Harang, P. B. Leavenworth

Development during the year 1941 on the Texas Gulf Coast resulted in the dis covery of 27 new fields as compared to 26 fields for the year 1940. Drilling.—During the year, 1405 wells were drilled. Of this number, 1031 were completed as oil wells with 375,000 bbl. daily of new production; 50 were com pleted as gas wells and 324 were failures. The most active area was Jackson County, where 375 wells were drilled and 336 of them accounting for 190,000 bbl. daily of new production. Types of Fields.—Of the 2 7 new fields, 14 are considered to be oil fields, 8 are listed as gas-distillate fields and 5 as gas fields. This may be compared to 26 fields found in 1940, of which 14 were oil fields and 12 gas-distillate fields. Producing Sections.—Frio discoveries retained their predominant position by having 10 Frio fields discovered in comparison to 6 fields in the Wilcox, 4 in the Yegua, 5 in the Miocene and 2 in the Jackson. In the previous year 15 Frio fields were found, 4 in the Wilcox, 2 each in the Yegua, Cook Mountain and Miocene, and I in the Jackson. Production.—Production increased over 1940 approximately 10 per cent, being 113,726,893 bbl. for the year 1941 and 104,127,247 bbl. for 1940. The statistics in Tables I and 2 include distillate and condensate as oil production because no separate reports have been compiled. It is hoped that this separation may be possible some day, but as a great many fields produce both oil and distillate and these arc commingled in pipe lines, separation of statistics will be more difficult than for other areas. New Fields Big Hill, Jefferson County.—Stanolind Oil and Gas Company's No. I George D. Anderson was completed as a gas well from a Frio sand at 8705 to 8720 ft., on Dec. 24, 1941, after having been drilled to a depth of 9500 ft. Additional development is being carried on but it is not possible to evaluate this discovery at this time. Brushy Creek Field, Lavaca County.— Shell Oil Corporation's No. I D. G. McManus was completed as the discovery well in the Brushy Creek field on Oct. 29, 1941, from a Wilcox sand through perforations at 7225 to 7230 ft., making gas and 180 bbl. of 59° gravity distillate. This well was bottomed at 10,998 ft. in the Wilcox. No statement can be made at this time as to the importance of this discovery. Chenango Field, Brazoria County.—J. N. Rayzor et al. completed their No. I Sarah J. Christian through perforations at 8564 to 8572 ft. in a Frio sand, for 453 bbl. of 37.7° gravity oil, on Feb. 6, 1941, after having drilled to 9564 ft. Several wells were drilled in this area during the year but failed to establish important production. This is considered a minor discovery. Clodine Field, Fort Bend County.—Providence Oil Company's No. I Hatfield was the discovery well of the Clodine field, being completed through perforations at 7499 to 7502 ft. for 108 bbl. of 51.2° gravity distillate, on June 19, 1941. The well was bottomed at 8090 ft. Several wells

Jan 1, 1942

By P. B. Leavenworth, Jack F. Harang

Development during the year 1941 on the Texas Gulf Coast resulted in the dis covery of 27 new fields as compared to 26 fields for the year 1940. Drilling.—During the year, 1405 wells were drilled. Of this number, 1031 were completed as oil wells with 375,000 bbl. daily of new production; 50 were com pleted as gas wells and 324 were failures. The most active area was Jackson County, where 375 wells were drilled and 336 of them accounting for 190,000 bbl. daily of new production. Types of Fields.—Of the 2 7 new fields, 14 are considered to be oil fields, 8 are listed as gas-distillate fields and 5 as gas fields. This may be compared to 26 fields found in 1940, of which 14 were oil fields and 12 gas-distillate fields. Producing Sections.—Frio discoveries retained their predominant position by having 10 Frio fields discovered in comparison to 6 fields in the Wilcox, 4 in the Yegua, 5 in the Miocene and 2 in the Jackson. In the previous year 15 Frio fields were found, 4 in the Wilcox, 2 each in the Yegua, Cook Mountain and Miocene, and I in the Jackson. Production.—Production increased over 1940 approximately 10 per cent, being 113,726,893 bbl. for the year 1941 and 104,127,247 bbl. for 1940. The statistics in Tables I and 2 include distillate and condensate as oil production because no separate reports have been compiled. It is hoped that this separation may be possible some day, but as a great many fields produce both oil and distillate and these arc commingled in pipe lines, separation of statistics will be more difficult than for other areas. New Fields Big Hill, Jefferson County.—Stanolind Oil and Gas Company's No. I George D. Anderson was completed as a gas well from a Frio sand at 8705 to 8720 ft., on Dec. 24, 1941, after having been drilled to a depth of 9500 ft. Additional development is being carried on but it is not possible to evaluate this discovery at this time. Brushy Creek Field, Lavaca County.— Shell Oil Corporation's No. I D. G. McManus was completed as the discovery well in the Brushy Creek field on Oct. 29, 1941, from a Wilcox sand through perforations at 7225 to 7230 ft., making gas and 180 bbl. of 59° gravity distillate. This well was bottomed at 10,998 ft. in the Wilcox. No statement can be made at this time as to the importance of this discovery. Chenango Field, Brazoria County.—J. N. Rayzor et al. completed their No. I Sarah J. Christian through perforations at 8564 to 8572 ft. in a Frio sand, for 453 bbl. of 37.7° gravity oil, on Feb. 6, 1941, after having drilled to 9564 ft. Several wells were drilled in this area during the year but failed to establish important production. This is considered a minor discovery. Clodine Field, Fort Bend County.—Providence Oil Company's No. I Hatfield was the discovery well of the Clodine field, being completed through perforations at 7499 to 7502 ft. for 108 bbl. of 51.2° gravity distillate, on June 19, 1941. The well was bottomed at 8090 ft. Several wells

Jan 1, 1942

By Paul Billingsley

THE purpose of this paper is a comparison, based on genesis, of the ore deposits associated with the igneous rocks of the central Montana Rockies. Considered separately, without attention to their origin, the orebodies appear to be distributed haphazard, with no fundamental laws controlling their position and character. It is believed, however, that if all the factors be weighed, this apparent confusion will to a large degree disappear. The, first essential to such a comparison is detailed knowledge of the individual mines, as to their geographic position (see Fig. 1), their mineralogical character, and in particular the derivation of their ores.1 The authors of this paper have pursued such an investigation for the past 6 years, and have accumulated a mass of evidence that enables a preliminary correlation to be attempted. It appears that the majority of ore deposits are genetically related to one or another of the igneous

Jan 4, 1917

By D. M. Davidson, P. F. Kerr

The Permian Cutler Formation in Kane Creek, Utah bears uranium ore in fissure-type vertical veins. This fissure vein formation and its associated host rock bleaching, weak argillic alteration, and base-metal sulfide mineralization along with the development of hydrothermal minerals, a 60 m.y. isotopic Pb/U age, and well-crystallized uraninite's structural control, give evidence of ore deposition in a hydrothermal environment consistent with Laramide mineralization. Mica polymorph studies indicate first, that temperature during the hydrothermal alteration or subsequent ore deposition did not exceed 200°; hence Cutler deposits are classified telethermal; and secondly, that rock alteration and ore deposition are closely related both in time and space, as is seen in argillic alteration sequence. Ore deposition in an alkaline to slightly acid reducing environment is postulated. Ore textures and mineral associations and distributions also indicate that carbonate complexes may have been transported with the deposing ores. Bleached rock formations are not primary strati-graphic phenomena. Bleaching, or changes in ferric iron content, results from a chemical process involving reduction and conversion of hematite to a soluble aqueous ion. Nearby Chinle bedded deposits (Moss Rack sandstone), containing shale lenses, fossil wood, organic debris and minor fractures, overly the Cutler formation. Chinle ores have a single reported isotopic age of approximately 200 m.y. Their chemical environment is assumed similar to that of the Cutler ores, though slightly more acidic. Two genetic, paradoxically divergent interpretations of the bedded deposits are derived from available spectrographic, petrographic, X-ray and chemical analyses. Kane Springs canyon is located southwest of Moab, Utah, south of the Colorado River and northwest of the Lisbon Valley mining district (Fig. 1). Uranium deposits occur along the northeast flank of a Kane Creek salt anticline where two geologic formations bear ore, the Permian Cutler and the Triassic Chinle. The Cutler deposits' fissure vein formation is an unusual occurrence in the Colorado Plateau. The Chinle deposits appear to be of the normal sedimentary type. Associated with the vein deposits are a number of features, including argillic alteration of sedimentary strata. The minerals of these deposits and their associated features have been studied in detail in a two year program entailing both field and laboratory techniques. STRATIGRAPHY A stratigraphic section of the lithologic units in the Kane Creek area is given in Table I.

Jan 1, 1967

By P. D. I. Honeyman

DURING 1938 many copper companies again felt the economic pinch and smelter operations were often on a reduced basis which some- times resulted in intermittent operations and complete shutdowns. During the last half of the year production was stepped up and smelting operations resumed a more normal appearance. One of the present-day trends in reverberatory sme1ting is definitely toward high-tonnage operations. i\ t the Phelps Dodge Corporation's Douglas plant, the reconstructed 107 by 26- ft. reverberatory furnaces are operated at the rate of 1000 tons of solid charge per day. The arch, all of silica brick; is sufficiently high above the bath to give

Jan 1, 1939

By Charles W. Merrill

Obsolescence in the mineral world is virtually nonexistent if the term is taken to mean that a mineral commodity, once established in commerce and industry, subsequently has fallen into disuse. We are living in an age of minerals. Each generation puts an increasing array of mineral-based commodities, in larger quantities, to more uses than ever before. Bastnasite, a museum mineral and a collector's item a few years ago, is now produced in quantity at Mountain Pass, Calif. Uranium, a minor byproduct of vanadium mining in the Rocky Mountain plateau area before World War 11, has grown to be a leading mineral product in several western States. And finally the total quantity and value of minerals both in the United States and in the World establish new records almost yearly. Surely the mineral industry as a whole is not obsolescent in our economy. Nevertheless, there are particular uses for particular minerals that are obsolescent and some applications have been supplanted entirely. Tin does not occupy the prominent place in foil manufacture that it once did, and the schoolboy's slate left most classrooms before the oldest of us were born.

Jan 9, 1964