Search Documents

By Allan T. Gwathmey, J. Bruce Wagner, Kenneth R. Lawless

Between 250°and 550°C in oxygen pressures of 10 to 760 mm Hg, the relative oxide thicknesses formed per unit time on the (100), (111), (110), and (320), decreased in this order. The predominant oxide orientation was (001)Fe3O4 and [110] Fe304 A small amount of a-Fe2O3 which exhibited a fiber pattern was observed in all oxides except those formed at 250°c in low oxygen pressures. IN order to understand the properties and behavior of thin films, particularly their role in oxidation reactions, there is needed more experimental information on their structure, composition, and kinetics of formation on clean surfaces of known geometry. The present study was undertaken to obtain such information for thin oxide films formed on single crystals of a body centered cubic metal, iron. Crystals in the form of spheres were used in order to expose all possible crystal planes to the reactant gases simultaneously. Using this procedure the relative rates of oxidation of all planes could be estimated, and those exhibiting, maximum or minimum oxidation rates could be selected for a more intensive study of composition and expitaxy. Since the three types of information were obtained from the same experiment using a single crystal substrate, any differences between rate, composition, and expitaxy on the several planes may be attributed to the influence of the substrate structure. EXPERIMENTAL The starting material for this study was Armco iron rods, 6 in. long and 3/8 or 1/2 in. in diam. The analysis was reported to be 99.8 pct Fe, with major impurities listed as carbon 0.018 pct, manganese 0.027 pct, phosphorous 0.005 pct, sulfur 0.029 pct, silicon 0.005 pct, and copper 0.11 pct. These rods were cleaned with ether and heated in an atmosphere of moist hydrogen at 950°C for three days. The purpose of this treatment was to decarburize the iron and to provide a consistent, uniform grain size for the growth of single crystals. Crystals in the form of rods, up to 1/2 in. in diam and 2 in. long, were prepared by a method similar to that reported by Leidheiser and Buck.2 Spherical crystals, 3/8 and 1/2 in. in diam and having a handle about 1/4 in. in diam by 112 in. long, were machined from the single-crystal rods. After machining, each crystal was etched in aqueous nitric acid to remove the cold-worked metal at the surface. Before each experiment, the crystal was polished mechanically with metallographic papers through number 4/0, and electropolished in a perchloric acid-acetic anhydride mixture by the method of Jacquet and Rocquet.3 The crystal was washed in running distilled water for at least 5 min. The excess water was blotted with a soft paper tissue, and the crystal was placed in an all-glass reaction vessel (See Fig. 1). The crystal was heated at 550°C in hydrogen for at least 8 hr prior to the oxidation in order to reduce any surface oxides and to help relieve any stresses in the metal. For the structure and composition studies, flat faces were cut parallel to (loo), (111), and (110) planes on the iron crystal spheres. The orientation of these faces was checked by a back-reflection X-ray diffraction technique. The faces were within 2 deg of the desired orientation. The flat faces were treated as described above except that prior to electropolishing they were given an additional polish on metallographic felt saturated with twenty-minute levigated alumina. After the crystal was heated in hydrogen for at least 8 hr, the temperature was adjusted to the desired value, and the hydrogen was evacuated. Commercial oxygen which had been purified by successively passing through tubes containing magnesium perchlorate, Ascarite and magnesium perchlorate was admitted to the desired pressure as measured by a mercury manometer. A resistance-wound furnace surrounded the oxidation chamber, and a temperature controller maintained the temperature within ±3°C. The furnace was provided with a small window for observing the crystal. The changes in thickness of the oxide films were followed by observing the interference colors. The oxidation was allowed to proceed until the desired oxide thickness was attained on a given crystal plane. The experiment was terminated by evacuating the oxidation

Jan 1, 1962

By Aureal T. Cross

THIS paper is a review of the published literature on research in coal geology, principally exclusive of resource studies, which appeared or became available during 1950 and the latter part of 1949. This report is not to be construed as being complete. The papers referred to in the bibliography are those among many more, which were read either in full or in abstract. Undoubtedly other papers were published which either escaped the author's notice or were not available to him. Those which were seen in abstract only (about one fourth of those listed) were not available in time for the inclusion of more than a notice. An outline of all papers listed in the bibliography has been arranged by subjects and reasonable subdivisions with some papers cited under more than one subject. Most papers are indexed according to the principal subject of discussion or research only as to an unusual or noteworthy section of the entire report. There will likely be some disagreement as to the quality or merit of some of the papers selected and the specialist may be supercritical of the outline or organization of papers in his field. It may be that attention has occasionally been drawn to papers reporting old information or conclusions of questionable value. Conferences and Meetings One of the best indications of the growing interest in coal geology problems in the United States is the increasing number of times this field has been the focus of attention at conferences and meetings. Notable among these are the joint meeting of the Society of Economic Geologists and the Geological Society of America at El Paso, November 1949, at which the principal thesis was concerned with low rank carbonaceous fuel deposits, especially of western United States. Among the papers given which are already available were those presented by Barghoorn,'" Parry? Roe? and Parks."' At the annual meeting of the Botanical Society of America in New York, December 1949, a joint meeting of the Paleobotanical and Microbiological Sections was held for which a symposium on Microbiology in Relation to the Geologic Accumulation of Organic Complexes was organized. Publication of the six papers presented by Ralph G. H. Siu, Elso S. Barghoorn, Irving Breger, Claude E. ZoBell, James M. Schopf, and A. C. Thayson is anticipated. At the regular meetings of the Paleobotanical Section at the same time, several other papers of interest reported on coal ball studies, partial coalification of petrified wood, and floras. In Chicago, April 1950, a symposium on Applied Paleobotany was held by the Society of Economic Paleontologists and Mineralogists in conjunction with the American Association of Petroleum Geologists. The five papers presented at this meeting dealt with the use of Paleozoic plant microfossils for stratigraphic work, J. M. Schopf, Devonian-Missis-sippian fossils of the black shales, Aureal T. Cross, Mesozoic plants of stratigraphic value, Th. Just, plant microfossils of the Tertiary, L. R. Wilson, and studies of the Brandon lignite, Elso S. Barghoorn. Early publication of these in the Journal of Paleontology is expected. The Nova Scotia Research Foundation and the Nova Scotia Dept. of Mines sponsored an excellent 3-day conference in June 1950, which dealt with several aspects of coal geology. Papers on coal classification, P. A. Hacquenbard, structure and sedimentation problems in Nova Scotia, T. B. Haites, new techniques of thermal analysis, W. L. White-head, geochemical investigations of Nova Scotia coals, Irving Breger, the role of fossil plant spores in coal correlation and the stratigraphy of the coal-bearing strata of the Appalachian Region, Aureal T. Cross, were given. Some discussions of these papers by those in attendance were recorded, and the entire proceedings is being prepared for publication. In September 1950, an unusual 3-day field conference was held by the Ohio and West Virginia Geological Surveys under the sponsorship of the Coal Geology Committee. This study of the stratigraphy, sedimentation, and nomenclature of the Upper Pennsylvanian and Permian coal-bearing strata of southeastern Ohio, southwestern Pennsylvania, and northern West Virginia was augmented by two discussions on associated rocks (clays and shales) and stratigraphic nomenclature at Wheeling and Morgantown, West Va. An extensive guidebook was prepared, and transcriptions of the Morgantown meeting were made. As a follow-up of the September field conference, a round-table discussion was held on this general topic at a special open meeting of the Coal Research Committee in conjunction with the November meeting of the Geological Society in Washington. Short prepared statements to invite discussion were given on each of several topics by L. M. Cline, Carl 0.

Jan 1, 1953

By Ernest J. Stocking

ENGINEERS are the key men in our war program today. Upon the technical knowledge and skill of the engineer and upon his administrative and executive abilities rests the entire success for the production of vital materials of the war. Naturally the work load of the engineering examining unit of the U. S. Civil Service Commission has increased greatly since our active participation in the war. At present, over 550 separate requests for certification of eligibles are received by the engineering unit per week. These represent more than a fourth of the total requests received for personnel by the Commission's central office at Washington and represent a recruitment work load of three to four times that carried by the whole Commission previous to January 1940. These requests represent a minimum of a thousand vacancies to be filled each week, while an average week will produce, at present, approximately 1400 vacancies and a weekly maximum may approach well over 2000 vacancies.

Jan 1, 1942

By Howard N. Eavenson

FROM the Pittsburgh coal bed in the four states of Pennsylvania, Ohio, Maryland and West Virginia has been produced an output that, at mine prices, represents a greater value than any other single mineral deposit in the world has yielded.12 While this distinction may in a few years pass to the gold reef of the Witwatersrand, it is possible that eventually, owing to the tremendous reserves still remaining, the ultimate yield of the Pittsburgh bed will be greater than that of any other known single deposit. Considering its importance, not a great deal has been written of its early history and development as a whole; most of the accounts have been of limited localities, or, at the most, of the area within a single state. In "Coal through the Ages" the writer mentioned some references to its early history, but this study will deal not only with its history but with the character of the bed, where and why it was first developed, and its effect upon the states in which it is found. It has not been the intention to write a detailed history of the development of the seam in each locality, as neither time nor inclination were available for doing such work, but only to show the influences that tended to hasten or retard such development. In general the historical matter ends about 1830, when geological surveys began to be made. Some of the maps show data available only since that time, and the sections about coal preparation and coking have been extended to the present time to show the changing conditions. It is believed that the early history includes all published records, and many more sources than those shown in the bibliography were consulted. It is quite likely that some references to coal in this area may be found in the unpublished papers of some of our early soldiers and colonizers, which exist in several libraries, and it is hoped that some future

Jan 1, 1938

With a mine output as high as 5000 tpd and mill capacity of 7000 tpd, the uranium mining and milling complex owned and operated by Kerr-McGee Nuclear Corp. in the Ambrosia Lake area is the largest in the U.S. and is likely to remain so for some time. Next year, Kerr- McGee expects to have in production another mine in Section 19 of the Ambrosia area-and will begin ore production in 1976 at its new $15-million mine at Church Rock, located northeast of Gallup, N. M., where the company has already completed the shaft work and is in the early stages of project development. Ore from Church Rock will be transported to the company's facilities at Ambrosia Lake for processing. Kerr-McGee's existing eight mines in Ambrosia Lake go to depths of about 800 to 1500 ft to tap the various horizons of uranium-bearing sands in the Westwater Canyon of the Morrison formation.

Jan 8, 1974

By B. S. Butler

The principal ore deposits of Arizona are in the southern, cen-tral, and western portions of the state, which physiographically are part of the Basin and Range province, southwest of the Colo-rado Plateau (Pl. I). The Basin and Range province is characterized by numerous subparallel mountain ranges separated by plains or valleys. Most of these ranges trend northwest to north, parallel to the margin of the Colorado Plateau; but in southeastern Arizona, southern New Mexico, and northeastern Sonora, they trend northward, transverse too the edge of the Plateau. The mountains rise abruptly from plains or valleys, the margins of which in many places are pediments cut on hard rock. Some of the plains form closed basins (bolsons, playas), but most of them are drained. The Basin and Range province in Arizona is divisible into the Mountain Region and the Desert Region4 (Pls. I and II). The Mountain Region forms a belt 60 to 100 miles wide that contains most of the large ore deposits. Its longest range measures about 55 miles, the widest 20 miles, and the highest peak more than 10,000 feet above sea level or 7,000 feet above adjacent valleys or plains. Broad plain-forming valleys are exceptional, but several with maximum widths of 20 to more than 30 miles appear in the southeastern portion. In the Desert Region the mountains are relatively low, narrow, serrated, and steep, with sharply angular profiles. There are a few exceptionally large ranges of which the longest measures nearly 100 miles and the widest 18 miles. The highest peak is some 7,000 feet above sea level, and the maximum local relief amounts to about 5,400 feet. Broad and comparatively low desert plains form 50 to 75 per cent of the area.

Jan 1, 1939

By Paul Averitt

The U. S. Geological Survey has been actively engaged in work on coal for more than 50 years. During this long period we have released more than 300 publications containing information about coal and coal reserves, including details on the thickness, distribution, and quality of coal, and the structure and stratigraphy of the coal-bearing rocks. We have also cooperated with state surveys on many similar publications. For many areas these reports are the only reliable published data on our resources of coal. During the last several years we have substantially increased our activities above the wartime low. We now have field work in progress, or reports in preparation, on 13 detailed mapping projects distributed as follows: 1. Pennsylvania anthracite field 2. Casselrnan Basin, Md. 3. Leslie County, Ky. 4. Deep River field, N. C. 5. Coosa field, Ala. 6. Powder River field, Mont. 7. Spotted Horse field, Wyo. 8. Yampa field, Colo. 9. Paonia field, Colo. 10. Trinidad field, Colo. 11. Durango field, Colo.

Jan 1, 1949

By H. I. Aaronson, C. Laird

The kinetics of thickening and of lengthening of ?' plates in an Al-3.93 pct Cu alloy in the temperature range 203" to 300" C were determined by means of transmission electron microscopy. The rate of thickening was found to be less than that allowed by volume diffusion control at all temperatures, by amounts which increased with decreasing temperature, in agreement with the predictions of a general theory of precipitate morphology.1 Thickening was treated on the basis of the ledge mechanism. Ledges were deduced to spread across the broad faces of ?' plates at volume dzjrfusion-controlled rates, as anticipated from the disordered structure of their edges. Lengthening of 8' plates, on the other hand, took Place more rapidly than allowed by volume dzjrfusion. This occurred despite clear morPhological evidence of a bmrier to growth at the edges of these plates. It was concluded that the misfit dislocation structure comprising the barrier requires that lengthening take place by a jog mechanism. The tnisfit dislocations, however, also serve as diffusion short circuits, and allow high overall lengthening rates to be achieved. In Part I' it was shown that, within the range of aging temperatures and times studied, the broad faces of 8' plates formed in Al-4 pct Cu are fully coherent with the a, matrix. Virtually .all of the dislocations present in these faces were found to have developed as a result of plastic deformation in the a phase. Such dislocations are thus "intruders", rather than the more usual misfit-compensating variety. The edges of 8' plates were confirmed, by extension of the earlier studies of Mat-suura and Koda,3 to be made up of edge-type misfit dislocations, in sessile orientation with respect to lengthening of the plates. These interfacial structures should cause 8' plates to thicken and to lengthen at rates less than those allowed under the condition of volume diffusion control, such as would be expected if the interphase boundaries had disordered structures.' The narrow width of 8' plates, the reproducible crystallography of their broad faces, and the appearance of these plates in cross section as octagons rather than as circular discs2 provide qualitative support for these deductions. The present study of the rate of thickening and the rate of lengthening of 8' plates was undertaken in order to examine them on a quantitative basis. I) THICKENING KINETICS OF THE BROAD FACES OF?' PLATES A) Literature Review. The measurements now available on the thickening kinetics of single-phase precipitate plates consist of one plot of the thickening of a proeutectoid ferrite plate in an Fe-C alloy,' showing (as predicted) thickening rates less than those allowed by volume diffusion control. B) Experimental Procedure. Details of the preparation of the 4-3.93 pct Cu alloy used in this study have been previously reported.4 As in Part 1,' transmission electron microscopy was the observational tool employed. A general description of the apparatus and procedures of the electron microscopy studies is given in Section I of Part I. In thin foils, 0' plates tend to form at and parallel to the foil surface.' A direct investigation of the thickening process by means of hot-stage transmission electron microscopy was therefore not feasible. It was thus necessary to use the conventional method of aging individual bulk specimens for a wide range of different times at the various temperatures studied. In each specimen, the thicknesses of a number of plates were measured. Since thin foils prepared from "bulk-aged" material contain a large proportion of grains with orientations near (001) , it was relatively easy to find, near the edges of the foils, the characteristic multifold patterns of intersecting extinction contours which indicate regions where the foil is exactly at an (001) orientation. The thicknesses of large numbers of plates were measured along the (200) branches of the "stars" so that the 8' plates were precisely parallel to the optical axis of the microscope. Wherever possible, intersecting extinction contours were adjusted with the parameter s > 0 to improve the visibility of the plates in bright-field illumination. These precautions, in combination with taking the measurements at the thinnest parts of the foils, minimized the errors in the measurement of the thickness of the plates resulting from inexact parallelism to the electron beam. Since the plates were very thin, it was not easy to measure their thickness on the photographs. The techniques of enlargement and of microdensitometry were employed to minimize errors from this part of the measurement. A further source of possible error, that the plates can appear thicker because of contrast associated with mismatch normal to the plane of the plate, was also considered. The images of the plates were usually thinner than those of dislocations, however, and no anomalous changes in apparent plate thickness were observed when regions of foil containing plates were tilted through various diffracting conditions. Any error from this cause must therefore be small. Other sources contributing errors were: a) the microdensitometer traces per se and the subjective estimates of their peak limits, and b) slight fluctuations in magnification associated with small changes in the current of the objective lens of the electron microscope. The overall error probably amounted to no more than 5 to 10 pct. In order to obtain readily interpretable data on thickening kinetics, it is essential that the diffusion fields of adjacent ?' plates not be allowed to overlap. Calculations'-' showed that this condition is definitely not ful-

Jan 1, 1969

By M. L. Brashears

IN the last 15 years industrial use of ground water has more than doubled, and in 1951 amounted to 5 billion gallons per day. A similar sharp increase in the utilization of ground water for irrigation and public-water supply occurred in the same period. In many areas rapid increase in withdrawal from wells has taken place almost entirely unhampered by regulatory control and with little or no integration of effort. As might be expected, the chief interest in many regions has been maximum production rather than sustained perennial yield. As a result, widespread depletion of underground reservoirs and deterioration of the quality of the water stored in them has taken place in many areas, even though total pumpage in the United States is far below ultimate potential. Of even more concern is the fact that excessive withdrawal has drawn salt water into the reservoirs beneath many heavily populated centers along the Atlantic, Gulf, and Pacific coasts, causing costly abandonment of pumping plants.' Many hydrologists expect that consumption of water will rise rapidly in the near future, and some predict that industrial requirements will more than double in the next decade.2,3 Thus it appears likely that the draft on many already heavily pumped underground reservoirs will be greatly increased and the search for additional sources of usable ground water intensified in years to come. In view of this, industry as a whole will be forced more and more to recognize the potentialities and limitations of ground-water reservoirs and to utilize them more effectively to prevent costly water shortages and disruption of production. Through painful experience, some industries are already well aware of the need for effective water utilization, and have managed individually or through joint effort to check trends threatening to deplete underground reservoirs completely or to impair the quality of the water. Various remedial measures have been used to bring about successful management of local or regional ground-water resources. Of these, replen-ishment of aquifers by recharge wells or basins has played an important role in overcoming some ground water problems. Artificial recharge of underground reservoirs by water spreading has been practiced successfully in the United States for many years. In the West it has become an important method of salvaging flood run-off for irrigation of crops and maintenance of public water-supply reserves, and it is used to some extent in parts of the East. Artificial recharge by means of wells, on the other hand, is a relatively new development. Until recently it was employed in only a few areas, principally along the East coast. For the last few years, in the ever increasing search for additional water supplies, industry has had greater recourse to this method. Utilization of recharge wells to control the temperature and quality of underground water supplies is also being considered seriously. Operation of recharge wells, like water spreading, is governed largely by local conditions. It requires water relatively low in turbidity, whereas in some areas water spreading has been used successfully with water of high turbidity and silt content. However, water spreading must be employed in large areas and can be carried on effectively only where aquifers crop out at the surface. Recharge wells can be used in limited space. Recharge wells are similar to production wells except that the water flows in the opposite direction. Thus any water-bearing bed that will yield water to wells may be recharged by wells. Often, however, the water available for recharge is of a different character and temperature from that existing in the ground-water reservoir and if transmitted directly underground from a recharge well to a production well might require expensive or difficult treatment before it could be used. Fortunately the physical characteristics of reservoir beds, which control the movement and behavior of ground water, are generally not homogeneous. Moreover, the movement of ground water is very slow because of the frictional resistance of the reservoir beds. By taking full advantage of hydrologic and geologic conditions, it is therefore possible in many instances to bring about favorable changes of temperature and dilution as the water moves from the recharge wells underground to the production wells. Furthermore, if the natural quality or temperature of ground water is unfavorable for industrial purposes, recharge wells may be used to introduce water of more favorable quality or temperature into the ground-water reservoir. When water is discharged into a recharge well, the head in the well is increased. Because of this, a cone of elevation is produced on the water table or the artesian pressure surface in the area surrounding the well. The cone of elevation is similar to the cone of depression produced around a pumping well except that the apex of the cone is above the water table or artesian pressure surface. Thus if a recharge well and a production well tapping the same water-bearing bed are close together, as would be the case at many industrial plants, some of the water discharged from the recharge well would be drawn into the production well within a short time. Under such conditions it is apparent that water of unfavorable temperature and chemical characteristics should not be used for recharging. The more important ground-water reservoirs in the United States often consist of alternating layers of impermeable beds and porous material that will yield water readily to wells. Physical characteristics of individual beds in a ground-water reservoir may not persist over great distances, the impermeable layers grading into beds that will yield large quantities of water. Thus the water-yielding material in underground reservoirs, whether large or small,

Jan 1, 1954

By H. I. Smith

WHEN Spain established colonies on the North American continent, some of her land grants, in what is now the United States, reserved to the Crown deposits of gold, silver, and mercury. Later mineral rights were reserved under some of the English Crown charters involving land in the eastern part of North America, with provisions for the payment of royalties thereon to the Crown. Reservation of mineral deposits to the United States Government was instituted by an ordinance of Congress on May 20, 1785, which applied to such deposits in the Northwest Territory, then north of the Ohio River and east of the Mississippi River, and provided that there should be reserved "one third of all gold, silver, lead, and copper mines, to be sold or otherwise disposed of as Congress shall hereafter direct." Little was known then of the mineral resources of the country; the Great Lakes copper region had just come into the possession of the United States by treaty and much of the western mineral land still belonged to France and Spain. The policy of leasing mineral deposits was enacted by Congress under the act of March 3, 1807, which provided that "the President of the United States shall be, and is hereby, authorized to lease any lead mine which has been or may hereafter be discovered in the Indiana Territory, for a term not exceeding five years," and in the same year the Government reserved 345,600 acres of land in northern Illinois, valuable for lead. In 1816 Congress provided that in all cases where a tract of public land containing a lead mine or salt spring was applied for by settlers on the public domain, no permission to work the mine or spring would be granted without the approbation of the President of the United States. By the act of March 1, 1847 (9 Stat. 146), the control of mineral lands was transferred, with all records, from the War Department to the Treasury Department, and by the act of March 3, 1849 (9 Stat. 395), supervisory powers over lead and other mines of the United States were transferred to the Secretary of the Interior. Following the discovery of gold in California in 1848, President Polk advocated the leasing of mineral lands acquired from Mexico under the treaty of 1848. However, owing to the lack of communication and transportation facilities and the consequent difficulty of checking on production and operations, leasing was found impracticable. Mining was permitted to be carried on in each district under rules made by the miners themselves and patterned after the Mexican mining system. To meet the situation, Congress enacted mining laws in 1866, 1870, and 1872, which provided for possession by location and for private ownership, after discovery, by patent of essentially all mineral deposits belonging to the United States, except coal. Many other acts were passed by Congress applying to specific regions and states, reserving salt, lead, or other minerals, some of which provided for the leasing of such deposits. However, very few if any leases were issued thereunder. Not until 1901 (31 Stat. 745) were the mining laws extended to include salt, and in 1910 they were revised to specify salines and associated products. At the turn of the century, it became more and more evident that the mining laws developed for metallic minerals were not practical for the development and conservation of oil and gas, coal, potash, phosphate, or oil shale. Following withdrawals by the Secretary of the Interior as authorized by the act of June 25, 1910, the Department of the Interior recommended leasing legislation; however, it was not until February 25, 1920, that the Mineral Leasing Act was passed by Congress. This act authorized leasing all public lands potentially valuable for oil, gas, coal, phosphate, sodium, or oil shale. The Organic Act, creating the Geological Survey in 1879, imposed upon its director the duty of classifying the public lands.' The early years of the Survey were devoted largely to the accumulation of fundamental data and, with only minor exceptions, land classification was not seriously undertaken until 1906. Since that year, it has been actively pursued with respect particularly to leasable minerals and water power values. On March 3, 1873 (17 Stat. 607) Congress authorized the sale of coal lands of limited acreage to individuals at $10 to $20 an acre, depending on the distance from a railroad, and in 1907 a new scale of prices was adopted by the Secretary of the Interior, based, more logically, on the quality and thickness of the coal deposits, their depth below the earth's surface, and their accessibility. At that time it was much cheaper and easier to obtain incidental title to coal rights under the homestead laws at $1.25 an acre. On March 3, 1909, the first separation act (35 Stat. 844) became a law. It authorized patents, with a reservation of the coal and mining rights involved to the United States, to persons who in good faith had entered public lands under the non-mineral land laws prior to withdrawal, classification, claim, or report that such lands were valuable for coal. It solved the problem only partially, and the practice thereupon adopted by the department of making coal withdrawals "from all forms of entry" instead of "from coal entry" expedited the more complete solution effected by later acts. By the act of June 22, 1910 (36.Stat. 583) withdrawn and classified coal lands were declared subject to entry under the homestead, desert land, and Carey acts, provided a waiver of the coal rights accompanied the application, and by the act of April 30, 1912 (37 Stat. 105) the same privilege was extended to State selections and isolated tracts. The act of August 24, 1912 (37 Stat. 496) extended the separation policy to lands withdrawn for oil and gas in Utah, and finally the act of July 17, 1914 (38 Stat. 509) extended it to all nonmineral filings on public lands theretofore or thereafter

Jan 1, 1955

By F. C. Frischknecht

Most early development and application of electromagnetic prospecting methods took place in Scandinavia, where geological conditions favor their use. In other parts of the world these methods have aroused cycles of interest, but in Scandinavia they have been used continuously and successfully since the 1920's. Electromagnetic methods may be classified into two general groups. One group includes methods in which the source of the electromagnetic field remains stationary while the receivers are moved about to explore the area. The other includes procedures in which the energizing and receiving systems are moved together. Other classifications could be based on the size of the energizing source, the particular components of the electromagnetic field which are measured, or the mode of transporting the equipment. The difference between fixed-source and moving-source methods, however, is of such great fundamental importance that it will be emphasized in this discussion. FIXED-SOURCE METHODS Essentially, a fixed-source method consists of the measurement of electromagnetic fields about the source. The mutual coupling between the source and the earth is constant, but the mutual coupling between the receiver and the earth (unless the earth is homogeneous) and also between the source and the receiver changes at each station. The results are usually normalized by relating the field data to the calculated free space or primary field. Turam and Radio Reference Signal Methods: The turam or two-frame* (see Fig. 1A) is probably * Turam means two-coil. the most common fixed-source method. The energizing source is an insulated cable grounded at both ends or formed into a large rectangular loop. Measurements are taken along a traverse at 5 to 50-meter intervals using two small receiving coils, the lagging coil being placed at the position previously occupied by the leading coil. The complex ratio (i.e., inphase and out-of-phase ratios) of the voltages induced in the two coils is measured. Operating frequency range is about 100 to 800 cps. In a typical turam survey a straight, grounded cable several kilometers long is laid out parallel to the probable strike of the ore deposits or conducting strata being sought. An area extending 1 or 2 km on each side of the cable, and within 1 or 2 km of the ends of the cable, is surveyed. Measurements are made at stations 5 to 25 m apart along traverses perpendicular to the cable. Measurements may be made along lines parallel to the cable to serve as base lines for the traverses or for other special purposes. Commonly the receiving coils are oriented with their planes horizontal so that only the vertical component of the field is measured. If additional information is required, one of the hori- zontal components may also be measured by orienting the coils with their planes vertical. In a modified turam technique developed recently for both ground and airborne measurements (Fig. 1B) the amplitude of the complex voltage induced in a single receiving coil is measured and its phase compared with that of a reference signal transmitted from the energizing system by a radio frequency carrier. Thus the un-normalized field is obtained directly, whereas with the turam method it is obtained by calculation from the ratios. The turam method and its modifications have a greater working depth than the other electromagnetic procedures used in ore prospecting. Under favorable conditions conductors have been located at depths of 200 to 300 m. A modified turam method with one of the electrodes grounded in the upper end of a plunging orebody was used to follow the extension of this body to a depth of 200 m beneath a layer of conducting schists. Straight grounded cables are usually preferred to insulated loops because they are easier to lay out and because they often make the method more sensitive. The greater sensitivity of a grounded cable is a result of ground return currents which may flow in the orebodies in addition to the eddy currents caused by induction from the current in the cable. Anomalies in the vertical field due to eddy currents are characterized by a correspondence between high values for the inphase component and positive out-of-phase components and/or low values for the inphase component and negative out-of-phase components. Also the inphase component may approach zero, but it does not become negative. In very long continuous conductors that are parallel to a grounded cable the effect of ground return currents may far exceed the effect of eddy currents. These ground return currents cause a lack of correspondence between the inphase and out-of-phase components and may cause negative inphase or anti-phase components. It becomes difficult to carry out the measurements and often difficult to interpret the results. Such results immediately suggest the presence of graphitic strata, however, since ore deposits are rarely extensive enough to accumulate sufficient ground return current to cause these results. A cable laid out perpendicular to the strike or an insulated loop is sometimes used in areas where graphitic schists and slates are present. Anomalies are then completely or almost entirely due to eddy currents and are easier to interpret. The measured voltage ratios are normalized by either subtracting or dividing by normal field ratios calculated from free space considerations. The normalized ratios are then plotted as individual profiles. When significant anomalies occur in the ratio measurements, the actual normalized fields are calculated by beginning with a measured or an assumed value for the field at a point near the cable and successively multiplying this value by the normalized ratios. There is a similarity between this process and a numerical integration of the ratio curve. Conversely, in many respects the ratio curve is similar to the first derivative of the field curve.

Jan 1, 1960

By J. N. Sicking, F. H. Brinkman

A new method for obtaining equilibrium vaporization ratios (K-values) for reservoir fluids has been developed and tested. By application of the method, complex experimental measurements of liquid and vapor phase compositions are eliminated. This simplified technique reduces the cost of experimental equilibrium-ratio data for reservoir studies of condensates and volatile crude-oil systems. The method is designed for systems of constant composition and, therefore, is best suited for depletion studies where compositional changes at high pressures are minor. The basic data required, in addition to the composition of the initial reservoir fluid, are the relative vapor-liquid volumes and densities at reservoir temperature and variom reservoir pressures. Tests demonstrated that the method predicts equilibrium ratios accurately for condensates. A single test on a crude oil was not conclusive; further testing will be necessary before the accuracy of the method can be determined for crude-oil systems. In addition to determining equilibrium ratios, the calculation method provides information on the physical properties of the "plus" component in the vapor and liquid phases. The "plus" component is that mixture of components heavier than the least volatile fraction analyzed. This information is useful in studies of both natural depletion and cycling operations for condensate reservoirs where the heptanes-plus component in the gas phase is produced from the reservoir. INTRODUCTION As more volatile oil and condensate reservoirs are found, the use of phase behavior techniques to predict their performance is increasing in importance. These techniques have long been used for condensate fields and have more recently been applied to crude-oil fields containing oils of medium-to-high volatility. In these phase behavior methods, equilibrium ratios (K-values) are used to predict compositional changes in the reservoir fluids—thereby accounting for the recoverable oil that exists in the gas phase. The reliability of the predictions depends to a large extent on the equilibrium ratios used. These values must be obtained for each component for the entire pressure range being investigated. Unfortunately, because of the complex nature of hydrocarbon mixtures, accurate K-values are hard to obtain. The equilibrium ratios for a particular component will vary not only with the temperature and pressure, but also with over-all composition of the system. The importance of composition is quite critical at elevated pressures, but becomes negligible at pressures below about 300 psia. Therefore, because most phase behavior problems involve the high-pressure region, each fluid system becomes a special case. Experimental programs to determine characteristic K-values are quite difficult and time-consuming. Thus, it is often necessary to resort to approximations of the K-value data. Charts giving K-values for various mixtures and classes of mixtures are available in the literature. However, there are two major difficulties in using them: (1) the K-values of the "plus" component (that mixture of components heavier than the last one analyzed) must be obtained by extrapolation from the K-values of the other components; and (2) the K-values obtained must finally be adjusted by trial and error to agree with observed volumetric data. To eliminate these difficulties, a new method of determining equilibrium ratios was developed. Briefly, after the composition of the system as a whole has been analyzed, the method uses empirical correlations and the gross fluid properties of the system (relative vapor-liquid volumes and densities) to calculate K-values. Because the calculative procedure is long, it is best solved on a digital computer. About one hour of machine time on an IBM 650 computer is required to develop a K-chart for the fluid being examined. DEVELOPMENT OF THE METHOD OF OBTAINING K-VALUES Equilibrium ratios are defined as the ratio of the mole fraction of a component in the vapor phase to its mole fraction in the liquid phase. This statement is expressed in Eq. 1. A typical plot of equilibrium ratios for a particular system is shown in Fig. 1. It should be noted that, at pressures near the saturation pressure, the K-values appear to converge to a common point. This apparent convergence point is called the convergence pressure and is a characteristic of the system involved. Various empirical correlations of K-values have been noted. It has been observed that an isothermal plot of

By R. Schuhmann

Available thermodynamic data applicable to copper smelting systems are collected and tabulated, and the important gaps are pointed out. A few examples are given of estimations which can be made from the available data. An experimental research program is proposed to supply the thermodynamic data that appear most essential to better quantitative understanding of the chemistry of copper smelting. The proposed program is designed also to shed specific light on the practical problems of slag losses and magnetite behavior. OPPER smelting, from flotation concentrates to V-/ blister copper, is conspicuous among the large scale chemical processes which are conducted with only relatively incomplete knowledge of the physical chemistry involved. For example, no common metallurgy text explains adequately why copper enters the matte phase while iron enters only to the extent that sulphur is left over after satisfying the copper. Explaining this important phenomenon as a manifestation of the greater affinity of sulphur for copper than for iron is unsound because the affinities of copper and iron for sulphur are about the same at smelting temperatures. As will be shown, other affinities are really decisive in the relatively clear-cut separation of copper in the matte. In contrast, thermodynamic studies have contributed much to our understanding of copper refining, zinc oxide reduction, magnesium production, steelmaking, etc. For each of these processes, the important reactions are clearly recognized, and fair to good quantitative values of the free-energy changes and equilibrium constants are available. Such data have proved to be of constantly increasing practical value in process development and improvement. Work in other fields has furnished much thermodynamic data applicable to copper smelting systems. In fact, several promising starts have been made in applying such data to specific smelting problems. Kelleyl made an appraisal of the possibilities of recovering elementary sulphur from low grade matte. His calculations and compilations of thermodynamic data have represented the starting point for much of the work in this field, including the present survey. Huang and Hayward2 nd Aksoy3 used thermodynamic methods in the study of copper losses in reverberatory slags. Peretti4 used thermodynamic data in explaining the chemistry of converting. The recent publications of Darken and Gurry"." and of Darken,' dealing with the iron-oxygen and iron-silicon-oxygen systems, respectively, present equilibrium data that are applicable to copper smelting systems. Also additional data were reported recently on the affinity of sulphur for copper, manganese, and iron8 and on the sulphur pressures of iron-sulphur melts." The survey presented in this paper was made as the basis for planning an experimental program on the thermodynamics of copper smelting. Few researches on the chemistry of copper smelting have been reported in recent years, so that a reappraisal and coordination of old and new data are essential if further work is to take the directions of maximum value. The experimental program is now in progress, and the plan of attack is outlined at the end of this paper. Progressive Oxidation and Desulphurization of Copper-bearing Liquid Phases: The chemical activities of sulphur and oxygen are two of the most important thermodynamic yardsticks to be applied to copper smelting processes. Virtually the entire smelting and refining sequence involves a series of systems characterized by decreasing sulphur activity and increasing oxygen activity. In this section, therefore, an attempt is made to define and explain these activities in terms of equilibrium partial pressures of SO2, s2, and O,. Also, estimates of these quantities are presented, the estimates being based largely on calculations presented in a later section of this paper. The sequence of steps from raw flotation concentrate to fully oxidized copper ready for poling involves progressive and controlled oxidation. Iron is oxidized and enters the slag. Sulphur is oxidized and leaves in the gas. Table I summarizes several important features of this oxidation and desulphurization sequence, starting at the beginning of the matte blow in the converter. The top line gives in order the principal smelting and refining stages up to fully oxidized copper, plus the additional step, not used commercially, of oxidizing all the way to Cu,O. In the second line are shown the principal copper-bearing liquid phases which characterize the process. Through most of the sequence the copper

Jan 1, 1951

By E. A. Farrell

A comprehensive survey is made of the status of the asbestos industry as it relates to marketing the product. Included are descriptions of the various types of asbestos and the grading and classification systems used. The uses of asbestos, distribution practices, and types of ore bodies are all related to marketing. World production, the producers and their capacities and world consumption for 1966-67 are summarized and statistical data are included. Asbestos is a general term describing a family of fibrous minerals of the serpentine and amphibole mineral groups. Asbestos has a long history going back to the time of the Egyptians, when it was used as a lamp wick. The commercial mining of asbestos started in Canada, Russia, and Africa in the 1800's, and the first asbestos products were made in Italy and Russia. The five main types of asbestos are: chrysotile, accounting for 95% of the total mined, amosite, crocido-lite, anthophyllite, and tremolite. Canada, Russia, and Africa are the major producers of asbestos. The commercial utility of asbestos was at first based on the heat resistance of the fibrous mineral in the form of packing, at the start of the industrial revolution. Its current utility is based more on its ability to reinforce binders such as portland cement, rubber, and plastics. Its inertness to the chemical nature of most binders is unique. Most important is its ability to maintain its reinforcing utility when the product is exposed to weather and soil conditions as in asbestos cement boards and pipe, and heat, pressure, and chemical exposure as in brake linings and gaskets and packings. The mineral asbestos is also unique because its fibrous form permits it to be spun and woven to cloth or formed into paper. Many asbestos applications are critical to national defense and at the present time, there are no satisfactory substitutes. Grading and Classification Canadian chrysotile asbestos fiber is graded and priced by length since basically the longer the fiber the higher the utility. The Canadian asbestos industry does not, however, classify the fiber by direct length measurement, but by a dry screening test. The method is called the Quebec Standard Screen (QS) test. One pound of fiber is mechanically shaken in four vertically stacked sieve boxes. The relative proportions remaining on the sieves defines the grade. The longer the fiber, the larger is the amount that stays on the top coarse screens and the less on the lower, finer mesh screens. Other tests can be used to further define the length distribution of fiber such as the wet screen Bauer McNett and the Suter Webb Comb (3 group only). The Canadian grading system divides the milled fibers into 5 main groups: group 3, 4, 5, 6, and 7, with 3 group being the longest, and 7 the shortest. Each group is further divided to subgrades, identified in each group by the letters A to Z, with "A" the longest and "Z" the shortest. See Appendix 1 for the Canadian QS classification system. The Russians also use the QS test on chrysotile. The Africans classify their chrysotile into grades similar to Canadian. The African crocidolite and amosite, however, are classified into actual length groups such as l to 2 in. and 2 to 3 in. Amosite and crocidolite are generally longer than chrysotile but also more brittle. Milled asbestos is not composed of staple length fibers like fiber glass or cotton, but of a mixture or blend of fibers ranging from long to short. Milled asbestos has a fiber length distribution similar to the particle size distribution of a powder. For example, the longest group 3 chrysotile grades have a high percentage of the longest fibers (1/2 to 3/4 in.) and low percentage of short fibers (0.003 in.). The figures in Table 1 give the approximate length distribution of the longest, middle, and shortest groups. A second and further method of classifying fiber is the degree to which the fiber bundles are separated to form a larger number of smaller diameter bundles. This property is normally described as the degree of fiberization, openness or surface area. Air permeability tests are used to measure surface area. Asbestos pro-

Jan 1, 1971

By Fred C., Bond

DETERMINATIONS of circulating load in a classifier operating in closed circuit with a grinding mill are usually made from screen analyses of the mill feed and classifier products. The percentage remaining on someone selected screen size must be used in the calculation, and, because of the wide variation in average particle size between the mill feed and classifier overflow, an accurate and representative result at the selected mesh is often difficult to obtain. To overcome this difficulty and reduce the time required in making the determination, I have devised a method which uses the liquid-solid relationship in the circuit rather than screen analyses. The quantities required for the calculation include only the usual dilution and feed tonnage measurements, which should be made regularly in the course of ordinary mill operation and, in addition, the amount of new water added to the classifier, or to the head of the mill with the new feed. If measurements are obtained on both of these quantities it is possible to check the calculated circulating load, and to calculate the percentage of moisture in the new feed to the mill; or, if the latter is known, to check the feed tonnage.

Jan 1, 1937

By C. W. Dunham

FOR discharging and diffusing the gases from the reverberatory furnaces and converters the Morenci Reduction Works has been provided with one of the largest reinforced concrete chimneys ever built. It is 612 ft. high from the bottom of the foundation to the cap at the top, and has a minimum diameter of 24 ft. inside the lining near the top and 38 ft. 10 in. at the bottom. Its estimated capacity, at the elevation of 4338 ft. above sea level, is about 1,000,000 cu.ft. of gas per minute at a temperature of 500° F. and an atmospheric temperature of 90°. Under these conditions the draft will be at least 3 in. of water at the flue inlet. The gases enter the chimney through a steel balloon flue 33 ft. high and 15 ft. wide, the bottom of which is 19 ft. above the ground.

Jan 1, 1942

C. N. FEnner, New York City (communication to the Secretary) : A possible explanation of some of the' phenomena of amalgamation cited by Mr. Bayliss and others has occurred to me. We know that if, to a quantity of mercury, gold and silver are added until a putty-like paste is formed, and if this mass is spread on a flat surface and pressure is applied, a more fluid portion of the mercury will be squeezed out from the rest, carrying gold and silver with it. The proportion of gold to silver will depend, I think, upon various causes and conditions—the relative chemical affinity which gold and silver have for mercury; the amount of pressure used; the presence of other metals:

Jan 1, 1898

Jan 1, 1930

Jan 1, 1944

[ ]

Jan 1, 1938