Search Documents

By B. H. Caudle, M. D. Witte

In predicting the performance of a pattern injection operation, the engineer needs to know both the amount of oil to be recovered and the rate at which the recovcry will take place. This paper- describes fluid flow model studies on the effect of mobility ratio on the rate of oil recovery in a five-spot. The results show the change in fluid conductivity (total flow rate/pressure drop) as the sweep-ont pattern increases for mobility ratios between 0.1 (and 10. There data, when cornbitted with a knowledge of reservoir permeabilities and sweep-orit pattern efficiencies, cata he used to predict the cLrmulntivr oil production as a function of time for homogeneous five-spot injection systems. INTRODUCTION The flow potential in a pattern flood element is a function of the mobility ratio and how far the injected flood front has gone.1,2 For a waterflood project having a mobility ratio of one, the conductance—which is the flow rate per unit pressure drop (q/Ap)—-will remain the same throughout the life of the flood. If the mobility ratio is favorable ( < I), the conductance of the project will drop continuously throughout the operation. If, on the other hand, the mobility ratio is unfavorahlc. the conductance ratio will increase continuously. Therefore, if the reservoir engineer wishes to predict either the rate at a specified pressure or the pressure at some rate for a secondary recovery project, he must know how the conductance will vary during the flood. Other investigators have studied this problem using potentiometric models&apos; or analytical solution&apos;. The

By George Macready

TRINIDAD, British West Indies, is an island near the north coast of South America, situated between latitudes 10° and 11° N:, and. opposite the numerous outlets of the Orinoco River Delta. It is separated from Venezuela by the Gulf of Paria (salt, water) and straits over 5 mi. (8 km.) wide. The area of the island is approximately 1750 sq. mi. (453,- . 250 hectares) and the population is approximately 400,000. The climate is tropical with an annual rainfall of from 45 to 60 in. (114 to 152 cm.). The oil fields consist of several units, or fields, located in the southern half of the island. Approximately 90 per cent. of the total production has been yielded by fields situated within 7 mi: (11.3 km.) of the famous asphalt lake and on the southwest peninsula. The most important producing fields, or units, are the following, which are shown on the accompanying map: Brighton, or Pitch Lake Field, operated by the Trinidad Lake Petroleum Co., Ltd., is situated beside the famous Pitch Lake; it, even encroaches on the lake. Vessigny Field, operated by the Trinidad Lake Petroleum Co., Ltd., is situated 2 mi. (3.2 km.) south of Pitch Lake. Lot One Field, operated by the Petroleum Development Co., Ltd., the United British Oilfields of Trinidad, Ltd., and Stollmeyer, Ltd., is situated 3 mi. south of Pitch Lake upon Lot One of Morne 1&apos;Enfer Forest Reserve and adjoining properties. Parry Lands Field, operated by the United British Oilfields of Trinidad, Ltd., and the Petroleum Development Co., Ltd., is situated 3;2 mi. south of Pitch Lake on Lot Three of Morne l&apos;Enfer Forest Reserve and adjoining properties. Point Fortin Field, operated by the United British Oilfields of Trinidad, Ltd., is situated at Point Fortin, 6 mi. southwest of Pitch Lake. Fyzabad Field, operated by Trinidad Leaseholds, Ltd., is situated several miles southwest of Fyzabad Village and 6 mi. south-southeast of Pitch Lake. Barracpore Field, operated by Trinidad Leaseholds, Ltd., is situated several miles south of. San Fernando and 15 mi. (24.14 km.) east of Pitch Lake.

Jan 9, 1920

By Alan Morris

BRASS rod for use in automatic screw machines is one of the major products of the brass mills. A large tonnage is consumed each year in the manufacture of an endless variety of finished articles and parts for assembly into other products. The machines that do this work have been developed to a high degree of efficiency, and their manufacturers are still striving for higher production speeds. This development has brought with it a demand for brass rod to meet the increasingly difficult machining conditions. This paper is a report of the results of tests undertaken in an effort to obtain a measure of the effects of such variables as lead content, microstructure and cold work on the machinability of brass rod. It is realized that the term "machinability" has never been well defined. Power, finish and tool life all should have a place in such a. definition. In practice it is sometimes found necessary to sacrifice some of these in order to obtain a rod that will not tend to throw up a burr, or will give a burr which is easily tumbled off. Again a specially stiff rod may be necessary because of long overhang from the chuck or a rod of special characteristics is needed to take a given broaching operation without chattering. It is only through an understanding of the effect of basic mill operations on the machinability of the rod that such problems as these may be solved most economically. It is hoped that this paper, together with the discussion it may evoke, will prove to be a basis for such an understanding.

Jan 1, 1932

By F. W. SUTTER

IN order to have ore available on the completion of the beneficiation plant at Clifton and to provide for continuous production while underground development was carried out, it was decided to develop an open-pit through the crest of a long hill in which the ore outcropped, using 40-ft. vertical benches.

Jan 1, 1943

By Richard Downs, Stephen P. Burke

The oxidation of pyritic sulphur associated with coal is important for the following reasons: 1. It is the predominant cause for the formation of acid mine drainage issuing from bituminous coal seams. This drainage pollutes the streams in coal regions, making the water unfit for industrial purposes and causing the disappearance of fish and wild life. As a consequence the movement of industry and especially recreational industry, so important to the population of these areas as an alternative means of livelihood, is impeded. 2. It is instrumental in effecting a series of reactions, which bring about the degradation and ultimately result in the spontaneous combustion of bituminous coal in storage. 3. It contributes to the breaking and shattering of the coal structure and is one of the causes of roof falls and floor lifts in mines. 4. It is the primary cause of the many nuisances associated with gob piles and the refuse of cleaning plants. 5. Its proper control and application might possibly be employed in the preparation of coal to reduce the inorganic sulphur content. The research that has been conducted on the oxidation of the various forms of iron sulphides is extensive and the literature voluminous. Nevertheless, few efforts have been made to determine experimentally and with some precision the mechanism of the reaction under the conditions of its occurrence in bituminous coal mines. It has generally been accepted that the oxidation of pyritic sulphur proceeds according to the reaction 2FeS2 + 2H2O + 7O2 ? 2FeSO4 + 2H2SO4 [1] The ferrous sulphate in the drainage streams is further oxidized by air to produce ferric hydroxide and more acid. Yet the literature fails to disclose any pertinent investigation on the mechanism of this reaction. The present contribution is concerned primarily with this aspect of the problem and while the work to be reported is not yet complete, it has yielded results from which interesting and significant conclusions may be drawn.

Jan 1, 1938

By F. Cadena

Hiwassee Darn, now under construction by the Tennessee Valley Authority on the Hiwassee River, a tributary of the Tennessee River, will require aggregate for approximately 800,000 cu. yd. of concrete. Near the damsite deposits of natural sand or gravel are not available and graywacke, a rock that is found in abundance, suggested itself as a likely source of manufactured aggregate. Graywacke is a metamorphosed sandstone composed principally of a mixture of quartz (65 per cent), mica (25 per cent), and feldspar (10 per cent). Other minerals are present in negligible amounts. The rock varies in different parts of the quarry from very fine to a coarse grain containing particles of about ¼ in. maximum size, although the bulk of the deposit is medium grain. Extensive tests showed that graywacke would be suitable as a source of both coarse and fine aggregates. The aggregate plant available for use at Hiwassee Dam consisted of the coarse-aggregate and sand plant used on the Norris project. The coarse-aggregate plant had also been used at Chickamauga Dam. Although most of this plant equipment is now in use at Hiwassee, the present flowsheet is not only different from that at Norris and Chickamauga but is also unique as compared to the flowsheet of the average crushed-stone aggregate plant. It is hoped that this paper will show the importance of proper arrangement of equipment if the optimum in flexibility and capacity is to be attained. Flowsheet Rock is ioaded by 3-yd. electric shovels into 12-yd. dump trucks, which carry the rock to the primary crusher, a 42-in. Superior McCully gyratory unit set at 4¾ in. (Fig. 1). The primary crusher discharges directly onto a 42-in. inclined belt conveyor, which carries the product to a surge storage pile with a maximum live storage capacity of approximately 3000 tons. A concrete tunnel under this storage pile houses the feed end of a 36-in. belt conveyor (conveyor B) fed by a 36 by 66-in.

Jan 1, 1942

By W. Rostoker, A. Siede

THE venerable problem of hydrogen embrittlement of ferritic iron lacks as yet a complete explanation. Possibly part of the difficulty has been the exclusive preoccupation with the total ductility prior to fracture. In the past few years it has been noted at least twice1,2 that hydrogen charged into iron has the ability to depress the upper yield point and, at room temperature, to eliminate completely the discontinuous yield phenomenon. Cracknell and Petchl rationalize that the depression of the yield stress is an example of the behavior of inhomogeneous stresses. Their explanation requires that microcracks exist in the annealed metal, and that hydrogen collect in these cavities under high hydrostatic pressure. The hydrostatic pressure of hydrogen generates localized tensile stresses in the iron which, with external loading, reach the critical stress for yield prematurely. The local plastic zones will spread across the specimen before the Lüders bands can be generated, and the yield-point elongation phenomenon is eliminated. This viewpoint will be discussed in succeeding paragraphs. Rogers,2 on the other hand, represents the depression of the initial flow stress as a result of the interaction of hydrogen with dislocations. He submits two alternative modes of interaction. In the

Jan 1, 1959

By Richard Downs, Stephen P. Burke

The oxidation of pyritic sulphur associated with coal is important for the following reasons: 1. It is the predominant cause for the formation of acid mine drainage issuing from bituminous coal seams. This drainage pollutes the streams in coal regions, making the water unfit for industrial purposes and causing the disappearance of fish and wild life. As a consequence the movement of industry and especially recreational industry, so important to the population of these areas as an alternative means of livelihood, is impeded. 2. It is instrumental in effecting a series of reactions, which bring about the degradation and ultimately result in the spontaneous combustion of bituminous coal in storage. 3. It contributes to the breaking and shattering of the coal structure and is one of the causes of roof falls and floor lifts in mines. 4. It is the primary cause of the many nuisances associated with gob piles and the refuse of cleaning plants. 5. Its proper control and application might possibly be employed in the preparation of coal to reduce the inorganic sulphur content. The research that has been conducted on the oxidation of the various forms of iron sulphides is extensive and the literature voluminous. Nevertheless, few efforts have been made to determine experimentally and with some precision the mechanism of the reaction under the conditions of its occurrence in bituminous coal mines. It has generally been accepted that the oxidation of pyritic sulphur proceeds according to the reaction 2FeS2 + 2H2O + 7O2 ? 2FeSO4 + 2H2SO4 [1] The ferrous sulphate in the drainage streams is further oxidized by air to produce ferric hydroxide and more acid. Yet the literature fails to disclose any pertinent investigation on the mechanism of this reaction. The present contribution is concerned primarily with this aspect of the problem and while the work to be reported is not yet complete, it has yielded results from which interesting and significant conclusions may be drawn.

Jan 1, 1938

By A. E. Harnsberger

IT is obvious that details such as the physical and chemical properties and methods of heat-treating of the materials mentioned must be omitted in a paper on the subject of materials used in oil-refinery pumps1. Only sufficient identification is given to enable the reader to find additional information from already published data. Also, the subject covers many operating conditions, but only the most important services can be discussed here. To the oil refiner, the pumping equipment is of vital interest. Practi-cally every refinery operation, from the charging of crude oil to a dis-tillation unit to the shipping of refined products, involves some form of pumping machinery. Intermediate refining stages involve a great variety of pumping machinery to carry out successfully the aims of the refinery technologist. Temperatures at which oils are handled vary from -50° F. to 900° F. Pressure may vary from subatmospheric to 2000 lb. per, sq. inch. The selection of the proper materials involves a careful consideration of the conditions under which the particular pump must operate. The four most important considerations are temperature, pressure, corrosion, and abrasion or wear. Consideration of temperature may be divided into three parts: (1) extremely low temperatures of the order of -50° F.; (2) temperatures at atmospheric or slightly above; (3) temperatures from 200° to 900° F. Pressures fall into two groups: (1) pressures reached by ordinary trade pumps of the order of 200 lb. per sq. in., (2) extreme pressure conditions involving pressures as high as 2000 lb. Noncorrosive and corrosive oils can be treated differently. Under the latter falls corrosion in the presence of water, which will occur up to 250° F. The second type of corrosion occurs in high-temperature pump-ing equipment, with temperatures from 450° to 900° F., largely caused by sulfur compounds. There are also other corrosive conditions met with

Jan 1, 1935

By C. R. Austin

In a recent paper1 the authors presented information on a refinement of the Rohn type of creep test with data on pure iron that exemplified the behavior of the apparatus. The present paper extends that work to nickel and cobalt and to the examination of the comparative high-temperature properties of two widely used commercial alloys. Careful attention has been given to the effect of plastic deformation in decreasing creep rate, using the elementary metals iron, nickel and cobalt for purposes of analysis. In any endeavor to develop new materials for high-temperature service one soon encounters a real problem as to the sort of test to be employed in evaluating the commercial possibilities of the alloys. At one time it was considered satisfactory to determine the tensile strengths at elevated temperatures and to use these values as a criterion for the commercial application of the alloys. More recently the proportional limit has been used as a means of classification. Data obtained from a form of bend test have also shown promise as providing a "merit index" of high-temperature serviceability.= Koerber and Pomp3 state that since the influence of testing time is small, the high-temperature yield point of steel furnishes sufficiently reliable and concordant values up to about 350" C. (and a maximum of 450" C. for alloy steels) to serve as a suitable basis for comparison evaluations of materials and for judging permissible stresses. Koerber and Pomp consider, however, that above these temperatures creep limit must be substituted for the high-temperature yield point as the all-important characteristic of the material. Whatever may be their definition of

Jan 1, 1934

By F. Cadena

Hiwassee Darn, now under construction by the Tennessee Valley Authority on the Hiwassee River, a tributary of the Tennessee River, will require aggregate for approximately 800,000 cu. yd. of concrete. Near the damsite deposits of natural sand or gravel are not available and graywacke, a rock that is found in abundance, suggested itself as a likely source of manufactured aggregate. Graywacke is a metamorphosed sandstone composed principally of a mixture of quartz (65 per cent), mica (25 per cent), and feldspar (10 per cent). Other minerals are present in negligible amounts. The rock varies in different parts of the quarry from very fine to a coarse grain containing particles of about ¼ in. maximum size, although the bulk of the deposit is medium grain. Extensive tests showed that graywacke would be suitable as a source of both coarse and fine aggregates. The aggregate plant available for use at Hiwassee Dam consisted of the coarse-aggregate and sand plant used on the Norris project. The coarse-aggregate plant had also been used at Chickamauga Dam. Although most of this plant equipment is now in use at Hiwassee, the present flowsheet is not only different from that at Norris and Chickamauga but is also unique as compared to the flowsheet of the average crushed-stone aggregate plant. It is hoped that this paper will show the importance of proper arrangement of equipment if the optimum in flexibility and capacity is to be attained. Flowsheet Rock is ioaded by 3-yd. electric shovels into 12-yd. dump trucks, which carry the rock to the primary crusher, a 42-in. Superior McCully gyratory unit set at 4¾ in. (Fig. 1). The primary crusher discharges directly onto a 42-in. inclined belt conveyor, which carries the product to a surge storage pile with a maximum live storage capacity of approximately 3000 tons. A concrete tunnel under this storage pile houses the feed end of a 36-in. belt conveyor (conveyor B) fed by a 36 by 66-in.

Jan 1, 1942

By M. C. Leverett

THE dynamic behavior of a multiple fluid system is completely describable in terms of driving forces and resistances to flow. The latter are proportional to the vis-cosity of the fluid under consideration and inversely proportional to a property of the system termed the " effective permeability" to that fluid, a property therefore defined by this relation. Since three phases are usually present in oil reservoirs, it is essential to know the effective permeabilities to the several fluid phases, and the relationship between the composition of the fluid in the pore space and that of the flowing stream, in order to handle satisfactorily certain problems of oil production. In this regard, there are many unknown factors and parameters, and many that can be evaluated only indi-rectly. However, it is expected that work along lines similar to this present under-taking will help materially in solving these problems. Previous workers in this field have inves-tigated the two-phase systems, water-gas,1 water-oil2 in unconsolidated sands, and water-gas3 in consolidated sands. The ex-tension of the study of the flow of hetero-geneous fluid systems from two to three phases involved only slight changes in technique. The apparatus used in the present work, except for slight changes to be described, was that used by Leverett in his water-oil experiments.2 Correlation and interpretation of data were made by methods analogous to those used in two-phase work. The relative permeability to a phase-the effective permeability divided by the permeability of the system to a homogeneous fluid-was employed through-out in correlating the rate of flow of that phase with the composition of the pore space. Quantitative measurements of two inde-pendent physical properties of the system were required to determine the composition of the pore space. As in the two-phase work, the fraction of water was determined electrically. The gas fraction was deter-mined by measuring changes in volume accompanying measured pressure changes. Suitable account was taken of the solubility of the gas in the liquid phases, and of the vapor pressure of the water phase. Since this work was exploratory in nature, no attempt was made to obtain highly accu-rate numerical results. Reasonable precision and reproducibility were sought.

Jan 1, 1940

By W. E. Keck, W. C. Lowry, G. C. Eggleston

The potential iron ores of Michigan can be classified from the stand-point of the predominant impurities into siliceous, sulphurous and phos-pllorous ores. Research on the flotation of each of these classes of ore was carried out in the following manner. The flotative properties of the valuable minerals of iron and of the worthless and deleterious ones were first determined under carefully controlled conditions. This information was then applied to synthetic mixtures of these minerals, which simulated the potential ores. Finally, data obtained during the two foregoing stages of the investigation were used in the flotation beneficiation of samples of the potential ores. Hematite is the most important mineral of iron in each of the above classes of iron ores. This paper deals with a study of that mineral in the very nearly pure state. There are two varieties of the mineral—specular hematite and massive hematite. The latter is the principal variety, but the former is an impor-tant&apos; mineral of iron in some of the potential ores. Because of this condition, flotation research was performed with both varieties. This research consisted essentially of: (I) a survey of the literature on hematite flotation, (2) the preparation of pure massive hematite, (3) the preparation of pure specular hematite, (4) the development of a laboratory procedure and (5) flotation experimentation. For the purpose of this discussion, the results of previous work on the flotative properties of hematite can be summarized as follows: Specular hematite has been readily floated with terpineol and sodium oleate or heptylic acid1. Further, hematite has been likewise floated with a proprietary frother and oleic acid or other soluble oils2. Finally, lead nitrate, copper sulphate, silver nitrate, chromium nitrate, mercuric chloride, ferric

Jan 1, 1939

By Harry H. Angst

The history and efficiency of 40-ton capacity dump trucks for surface waste removal at the New Cornelia opencut copper mine, at Ajo, Ariz., are summed up in this paper. Tabulations of truck performance, together with detailed cost figures, prove the value of truck transportation for certain special operations at a large mine. Emphasis is given to the fact that truck transportation not only reduces the haulage costs but also reduces the breaking ground and shovel-loading costs per ton. The New Cornelia opencut copper mine is in the desert. The climate is ideal for seven months of the year, but the five summer months are uncomfortably hot. &apos;She elevation is 1820 ft. above sea level and the annual rainfall is approximately 6 inches. The ore body is a monzonite-porphyry deposit. The waste-rock capping consists of hard rhyolite, conglomerate and porphyry. All the material is hard and cannot be excavated without blasting. The rhyolite and conglomerate waste is very blocky. The weight of the rock in place is 2.16 tons per cubic yard. The average mine production per day is 22,090 tons of 012 and 18,000 tons Of waste rock, the latter consisting of surface rock and material within the ore body too low in grade to send to the concentrator. The rock is loaded by electric shovels with 4½-cu. yd. dippers. The primary transportation of ore to the concentrator and waste to the dumps is by 30-yd. dump cars and oil-burning steam locomotives; therefore truck haulage of waste is a minor factor of the New Cornelia operation. However, as New Cornelia was one of the first mines to use large-capacity dump trucks for haulage, the results obtained are of interest. Equipment On the south side of the New Cornelia is a hill rising about 500 ft. above the normal surface elevation, roughly 1000 ft. in diameter at its base, called locally Arkansas Mountain peak. Exploratory drilling in this area developed additional ore that could be made accessible for open pit operation only by moving the mountain face a maximum distance of 400 ft. to the south. The slope of the mountain adjacent to the pit averaged 35°, and the small area involved precluded the use of train haulage for the removal of the 4,000,000 tons of waste estimated above the normal pit elevation. A study of dump-truck haulage at Boulder Dam and San Gabriel Dam led to the decision to use large-capacity end-diii~lp trucks rather than smaller trucks, for the following reasons: I. The truck would have to withstand the impact of hard, heavy chunks, some of them weighing as much as 10 tons, which would be dumped from the 4½-cu. yd. dipper. 2. The coarse, rocky, abrasive material would soon damage a light truck body. 3. The body of a small truck could not be efficiently loaded with coarse rock.

Jan 1, 1943

By Benjamin N. Webber

The peninsula of Nicoya contains virtually all of the known manganese deposits of Costa Rica. These are south and west of the Tempisque River, which flows across the peninsula near its juncture with the mainland. This peninsula forms the westernmost part of the province of Guana-caste, which is the northern. of the two Pacific Coast provinces of Costa Rica. The larger villages are connected by ox-cart roads and trails. The area may be covered on horseback without difficulty except during the rainy season, when rivers are in flood and difficult to ford. This is particularly true of the Rio Seco-Guay-jiniquil area, where there are no inhabitants and few open trails through the tropical jungle. Santa Cruz and Sardinal are served by the Taca Airlines, two planes a week from San Jose and Puntarenas. The port of Puntarenas has excellent loading facilities but none are available nearer the manganese districts; there ore must be lightered to vessels standing offshore. Physiography In Costa Rica there are three physiographic divisions: (I) the central plateau (Mesa Central), a somewhat dissected lava platform upon which are superimposed volcanic peaks, some of which are still active; (2) the Atlantic lowlands and (3) the Pacific lowlands. The peninsula of Nicoya and the larger part of the province of Guanacaste lie within the Pacific low- lands. The term "lowland" indicates relation to the central plateau, as the peninsula of Nicoya is largely mountainous. The mountains of Nicoya form the southern extremity of a range of low hills, which are almost continuous along the Costa Rican coast to the Nicaraguan border. The coast line shows evidence of subsidence. The Gulf of Nicoya obviously is the drowned valley of the Tempisque River. The west coast of Nicoya shows many rocks, shoals, bays, inlets and small islands as evidence of a sea encroachment. The altitude of the manganese deposits ranges from 0 to 800 ft. Topography is of the mature type of wide valleys and low hills, often with abrupt slopes. The climate is tropical and humid; rainfall of 125 in. falls largely between Sept. I and Jan. I. Vegetation often is very dense, the Rio Seco-Guayjiniquil area being truly tropical jungle, containing many hardwoods. History and Production The production of manganese ore in Costa Rica apparently dates from the first World War. It reached a peak of about 10,000 tons in the year 1919, then declined rapidly. Evidence of this period of prospecting has rotted away or been swallowed by the jungle. The war now in progress apparently revived the interest in Costa Rican manganese and has encouraged further prospecting. Deposits long known have been redenounced and trails have been cut through the jungle to them. Many new deposits have been discovered in the last

Jan 1, 1949

By Harry H. Angst

The history and efficiency of 40-ton capacity dump trucks for surface waste removal at the New Cornelia opencut copper mine, at Ajo, Ariz., are summed up in this paper. Tabulations of truck performance, together with detailed cost figures, prove the value of truck transportation for certain special operations at a large mine. Emphasis is given to the fact that truck transportation not only reduces the haulage costs but also reduces the breaking ground and shovel-loading costs per ton. The New Cornelia opencut copper mine is in the desert. The climate is ideal for seven months of the year, but the five summer months are uncomfortably hot. &apos;She elevation is 1820 ft. above sea level and the annual rainfall is approximately 6 inches. The ore body is a monzonite-porphyry deposit. The waste-rock capping consists of hard rhyolite, conglomerate and porphyry. All the material is hard and cannot be excavated without blasting. The rhyolite and conglomerate waste is very blocky. The weight of the rock in place is 2.16 tons per cubic yard. The average mine production per day is 22,090 tons of 012 and 18,000 tons Of waste rock, the latter consisting of surface rock and material within the ore body too low in grade to send to the concentrator. The rock is loaded by electric shovels with 4½-cu. yd. dippers. The primary transportation of ore to the concentrator and waste to the dumps is by 30-yd. dump cars and oil-burning steam locomotives; therefore truck haulage of waste is a minor factor of the New Cornelia operation. However, as New Cornelia was one of the first mines to use large-capacity dump trucks for haulage, the results obtained are of interest. Equipment On the south side of the New Cornelia is a hill rising about 500 ft. above the normal surface elevation, roughly 1000 ft. in diameter at its base, called locally Arkansas Mountain peak. Exploratory drilling in this area developed additional ore that could be made accessible for open pit operation only by moving the mountain face a maximum distance of 400 ft. to the south. The slope of the mountain adjacent to the pit averaged 35°, and the small area involved precluded the use of train haulage for the removal of the 4,000,000 tons of waste estimated above the normal pit elevation. A study of dump-truck haulage at Boulder Dam and San Gabriel Dam led to the decision to use large-capacity end-diii~lp trucks rather than smaller trucks, for the following reasons: I. The truck would have to withstand the impact of hard, heavy chunks, some of them weighing as much as 10 tons, which would be dumped from the 4½-cu. yd. dipper. 2. The coarse, rocky, abrasive material would soon damage a light truck body. 3. The body of a small truck could not be efficiently loaded with coarse rock.

Jan 1, 1943

By H. K. Birnbaum, H. B. Aaron

he authors suggest that a number of the types of yield phenomena which have been observed in high-purity fcc metals are due to dislocation interactions bccurring at the surface of the crystals rather than due to volume effects. Since rather different inter-pretationS2,7,12,14,15,21-23 of these effects have been suggested, it is of some importance to ascertain the role of the surface in these yield phenomena. It should be first noted that the high-purity fcc metals appear to exhibit several distinct types of yield phenomena. The "unloading yield point" which is observed on reloading the specimen after removing the applied load has been found to be independent of the time of holding in the unloaded condition. If however the specimen is aged while under load and re-tested without removing the load, a yield point is observed which does depend on the aging time and tem-perature. Feng and Kramer suggest that the removal of the unloading yield point on removing sufficient material from the surface of the specimen indicates that the effect is associated with dislocation interactions at the specimen surface. Their observations are counter to those of Haasen and Kelly5 and Birnbaum.12 Since the unloading yield points are extremely small (-2 pct of the flow stress) the results of the surface removal will depend on whether the material is removed uniformly over the gage length. The introduction of small etch pits or the removal of more material from one portion of the specimen than from another will result in preferential yielding and obliteration of the yield point. With the normal electropolishing techniques it would be difficult to avoid these effects. The data obtained by Aaron and Birnbaum, Fig. 10, on aluminum polycrystalline specimens indicate that, although the unloading yield point and the strain-aging yield point are not simply additive, a time- and temperature-dependent yield point is observed under conditions where no creep is observed. This does not agree with the results of Feng and Kramer but does agree with the results on copper15 and gold.7~23 The source of the discrepancy may be the procedure used by Feng and Kramer to correct their time-dependent yield points for the effect of creep. Since the strain-aging yield point is not independent of the pre-aging strain rate, Fig. 11, the effects of creep cannot

Jan 1, 1967

By R. C. Ruder, C. E. Birchenall

The method of decrease in surface activity was used to determine the rates of diffusion of Co" into cobalt and into nickel. Since the absorption curves for cobalt radiation were quite complex under the conditions of these experiments, the effects of geometry and surface preparation on the diffusion results were investigated. The cobalt self-diffusion coefficients obey the equation DCoco = e-61100/RT cm2 per sec. For dilute cobalt diffusing in nickel, DConi, == 1.46 e-/R&apos; cm2 er sec. AS part of the general program to measure the self-diffusion and dilute-solution diffusion rates of the iron-group metals, the diffusion coefficients of cobalt into cobalt and nickel have been measured using the radioactive isotope Co"&apos;. Self-diffusion studies in iron have been previously reported by Birchenall and Mehl.&apos; The technique of measurement used was the decrease in surface activity method described by Steigman, Shockley, and Nix.&apos; It has been determined that scattering of the measured beta radiation by the specimen matrix is significantly influenced by the condition of the surface and the counting geometry. Accurate diffusion coefficients can be calculated from the activity data provided that the specimens have plane diffusion surfaces and that the absorption properties of the emitted radiation are determined under geometrical conditions duplicating with external absorbers the absorption and scattering in a thin film at the specimen surface as nearly as possible. The cobalt used in this research was originally in the form of hydrogen reduced rondels 99.9+ pct pure. The nickel had been prepared by the carbonyl process and was found by spectrographic analysis to contain 0.03 pct Fe, 0.04 pct Co and smaller traces of other metallic elements for a balance purity of 99.9+ pet Ni. Both materials were vacuum melted and cast in rectangular ingots. Specimens 7/8x7/8x1/4 in. were machined from these ingots. The specimens were then ground to 4-0 emery paper and annealed in hydrogen for at least a day at 1200°C. Some of the specimens were used in preliminary experimentation after which their diffusion faces were machined to remove the radioactive material from the previous diffusion experiments. After grinding, the specimens were polished using an electrolytic lapping technique described by Mazia." This lapping was continued until at least 0.005 in. was removed from the diffusion surface. The final surfaces were metallographically smooth except for a few fine scratches caused by the glass cloth. A large percentage of the area was undisturbed as determined by microscopic examination. The grain diameters of the diffusion specimens varied from 0.1 to 5 mm. There were no effects due to grain boundary diffusion in the experiments

Jan 1, 1952

By M. G. Nicholas

The influence of deformation, relative movement and surface cleanliness on the strength of room -temperature "interparticle" bonds between copper surfaces has been studied. No bonding resulted when clean surfaces were merely pressed together, even under pressures of 50,000 psi. Bonding resulted, however, when clean surfaces were simultaneously pressed and moved relative to each other, some bonding occurring no matter how small the pressure or relative movement. Exposure of the clean surfaces to various chemicals inhibited bonding, none at all being produced by small relative movements. The size of the movements which first produce bonding between exposed surfaces depends on the nature of the chemical, being less than 0.002 in. for cleansing reagents and greater than 0.004 in. for lubricants, water and hydrogen sulfide. It is concluded from the experimental data that the prime requirement for bonding is the dispersal of surface films such as oxides and adsorbed contaminants. THE formation of interparticle bonds during the room-temperature compaction of powder metallurgy components greatly increases the ease of handling in subsequent production operations prior to sintering. The strength of unsintered compacts follows the same general trends as their density and hardness, but quantitative data are extremely Scarce. Quantitative correlation of the data on the overall strength of a compact with that of the individual interparticle bonds is virtually impossible due to the extremely complex geometry of powder compacts. Qualitatively, however, the strengths of unsintered compacts can be correlated with variations in parameters known to influence the extent of cold bonding, and hence interparticle bonding, such as surface cleanliness, relative movement, and deformation of the mating surfaces. Kuzmic and seelig4 found that contamination of powder particle surfaces with lubricants reduced the strength of unsintered iron and copper compacts. Interparticle shear has been shown to promote bonding by Train and Hersey7 while Gregory has shown that die rotation is beneficial. Eilender and schwalbe6 concluded that most bonding occurred during the early stages of pressing iron powder compacts when interparticle shear is one of the principal processes occurring. mile there can be little doubt that these and other factors, such as particle size and shape, affect the extent of interparticle bonding produced by compaction, evaluation of the influence of individual factors is not easy. Particle deformation and relative movement, for example, occur simultaneously during compaction, making any precise measurement of their relative influences difficult. Because of these and other difficulties encountered in studying interparticle bonding in actual powder compacts, the approach adopted in this study was to

Jan 1, 1963

By Benjamin N. Webber

The peninsula of Nicoya contains virtually all of the known manganese deposits of Costa Rica. These are south and west of the Tempisque River, which flows across the peninsula near its juncture with the mainland. This peninsula forms the westernmost part of the province of Guana-caste, which is the northern. of the two Pacific Coast provinces of Costa Rica. The larger villages are connected by ox-cart roads and trails. The area may be covered on horseback without difficulty except during the rainy season, when rivers are in flood and difficult to ford. This is particularly true of the Rio Seco-Guay-jiniquil area, where there are no inhabitants and few open trails through the tropical jungle. Santa Cruz and Sardinal are served by the Taca Airlines, two planes a week from San Jose and Puntarenas. The port of Puntarenas has excellent loading facilities but none are available nearer the manganese districts; there ore must be lightered to vessels standing offshore. Physiography In Costa Rica there are three physiographic divisions: (I) the central plateau (Mesa Central), a somewhat dissected lava platform upon which are superimposed volcanic peaks, some of which are still active; (2) the Atlantic lowlands and (3) the Pacific lowlands. The peninsula of Nicoya and the larger part of the province of Guanacaste lie within the Pacific low- lands. The term "lowland" indicates relation to the central plateau, as the peninsula of Nicoya is largely mountainous. The mountains of Nicoya form the southern extremity of a range of low hills, which are almost continuous along the Costa Rican coast to the Nicaraguan border. The coast line shows evidence of subsidence. The Gulf of Nicoya obviously is the drowned valley of the Tempisque River. The west coast of Nicoya shows many rocks, shoals, bays, inlets and small islands as evidence of a sea encroachment. The altitude of the manganese deposits ranges from 0 to 800 ft. Topography is of the mature type of wide valleys and low hills, often with abrupt slopes. The climate is tropical and humid; rainfall of 125 in. falls largely between Sept. I and Jan. I. Vegetation often is very dense, the Rio Seco-Guayjiniquil area being truly tropical jungle, containing many hardwoods. History and Production The production of manganese ore in Costa Rica apparently dates from the first World War. It reached a peak of about 10,000 tons in the year 1919, then declined rapidly. Evidence of this period of prospecting has rotted away or been swallowed by the jungle. The war now in progress apparently revived the interest in Costa Rican manganese and has encouraged further prospecting. Deposits long known have been redenounced and trails have been cut through the jungle to them. Many new deposits have been discovered in the last

Jan 1, 1949