Search Documents

By C. Kremer Bain

DURING the past several years of diamond drilling in Washington County, Mo., the St. Joseph Lead Co. has discovered a concentration of commercial lead-zinc ore at four different points within an area of 36 square miles. The largest and to date the most promising group of these orebodies is located in the Indian Creek area. It was considered to be of sufficient value to warrant development. The Indian Creek area is in the center of the northern half of Washington County, 11 miles northwest of Potosi, Mo., the county seat. The location is readily accessible from Potosi by car or truck over the all-weather Missouri State Highway No. 114. The topography is one of rolling relief, varying from an elevation of 700 ft above sea level on Mineral Fork and Indian Creek to a maximum of 1176 ft at High Point Tower. It is divided in equal halves between the drainage to Mineral Fork and to Indian Creek. The shaft site at 1060 elevation is on the divide between the two drainage areas. The Indian Creek side is rough and heavily wooded, with only a few cultivated clearings. The slopes to Mineral Fork are more gentle and rounded, with much of the area cleared for farm land. Most of the surface is covered with Potosi and Eminence formations, which show little evidence of any structure. Ore structure was worked out by extensive diamond core drilling, with holes varying in depth from about 700 to 1300 ft. As of Oct. 1, 1950, 218 prospect holes had been drilled within the 36-square mile area. The ore is disseminated galena with considerable accompanying sphalerite in the Bonne Terre forma-tion in the shape of irregular blanket-type deposits. The main controlling structural feature of the outlined mineral zone is a buried pre-Cambrian rhy-olite-porphyry ridge extending partly through the Bonne Terre formation, which laps against the por phyry and also covers it. The mineralized zone parallels and forms an irregular halo around the porphyry ridge and is concentrated in the Bonne Terre formation where the La Motte sandstone is cut out by the porphyry ridge. This is a very common mineral occurrence in the southeastern Missouri lead belt district. The La Motte sandstone, which normally underlies the Bonne Terre formation, is thus cut out entirely. In this area the Bonne Terre is usually about 275 to 320 ft thick, the La Motte varying in thickness from zero up to 400 ft. Commercial concentrations of ore are indicated at several places, the most notable being at the shaft site where an orebody at least 4000 ft long with widths of 500 to 600 ft has been outlined. The total thickness of mineralized rock reaches 150 ft in some holes, although total ore thickness runs from 8 ft to about 60 ft, often in more than one layer. Preliminary Planning Ore reserves as outlined lend themselves to open-stope mining with trackless haulage and mobile loading machines and drilling equipment. This type of equipment has proved to be very efficient during recent years in the company's lead belt operations. After a study of bids for shaft sinking and an estimation of comparative costs, it was decided that the shaft would be sunk by St. Joseph Lead Co. personnel using company equipment. Since the plant site is about 26 miles from the company's nearest lead belt operations, it was necessary to plan a complete surface plant, including mill, shops, office, change room, and warehousing facilities. Immediately following the filing of an application for a certificate of necessity, a headframe was selected for which detailed drawings were already available. The order was placed for fabrication so that it could be delivered and erected in time to serve for sinking the shaft. This eliminated the expense of a temporary headframe. Drilling was started on two churn drill holes near shaft location, and two 1000-gpm deep well pumps

Jan 1, 1954

By R. J. Grace

Primarily, this report presents the results of direct efficiency tests which were conducted on the 200-hp Coal-Pak, hot water generator, No. 3 unit, at the Otterbein College heating plant in Westerville, Ohio. Also included is a comparison of fuel consumption of the old plant with that of the new plant, a comparison of efficiencies obtained by the indirect method on a 300-hp Coal-Pak, and the cost of gas vs coal to show the savings effected by the latter. Tests were conducted with ten different bituminous coals selected by Mr. S. A. Frye, business manager at Otterbein College. The coals, of ten different suppliers, from four different states and eight different seams, represented competitive products economically available to the heating plant. The tests were conducted by the usual plant personnel which consisted of the plant superintendent and two assistants. No outside supervision of any kind was given during the tests. The tests were made from Dec. 13, 1960, through Mar. 4, 1961. During this period, 300.03 tons of coal were burned in the No. 3 unit. This tonnage represented 25.5 pct of the total coal requirements for the 1960-61 season. Operation during the period was typical for the comfort heat load which the plant supplies. Of the 78.12 operating days, the boiler was on bank or holdfire 14.31 days, or 18.32 pct of the time. The length of individual bank periods varied from 2 hr to three days. Run periods varied from about 2 hr to 7.26 days. DESCRIPTION OF PLANT AND HEATING EQUIPMENT The new Otterbein College heating plant, completed in the summer of 1957, is located in a 50x50 ft boiler room on the lower level of a combination maintenance building and heating plant. The building is situated away from the main college complex on a hillside, which allows for on-grade delivery of coal to the three bunkers. The bunkers are located directly above and connected with the individual stoker hoppers. Fig. 1 shows an in-plant view of the Coal-Pak installations. The No. 3, hot water, unit is at the extreme right. The heating plant consists of three 200-hp Coal-Paks. Unit No. 1 is operated at 4 psi and carries the steam heating load of 14,000 sq ft EDR (steam) installed in two buildings. Provision has been made to convert these buildings to hot water heating at some future date. Since the unit under maximum load conditions operates only at about 50 pct steaming capacity, a heat exchanger was installed to convert steam to hot water. Thus, during light loads in mild weather the unit can be employed more efficiently to supply both steam and hot water and eliminate the need for operating either of the two hot water units. Units No. 2 and No. 3 serve a hot water heating circuit for a large group of 21 buildings of the College. These boilers deliver hot water at temperatures up to 200°F to the various buildings through distribution lines in tunnels. The present calculated maximum heat loss for the College is 15.195 million Btu per hr. The Coal-Paks have individual design capacities of 6.700 million Btu per hr. Table I lists the design date for the Coal-Paks. The No. 3 unit was chosen as the test unit, primarily because of its bunker location at the far end of the delivery ramp. Because of this location any excess coal above bunker capacity could be conveniently stored and isolated from the adjoining bunkers. Each bunker has a capacity of 30 to 35 tons of coal. The No. 2 and No. 3 hot water generators are equipped with automatic controls which maintain the

Jan 1, 1962

By A. E. Zawadzki

A progress report is presented on the development of a process for the removal of sulfur dioxide from flue gases. Catalytic oxidation of the sulfur dioxide in flue gases, with the production of recoverable sulfuric acid, has been demonstrated to be technically feasible. Problems associated with the process are discussed. The need for an inexpensive and efficient process for controlling sulfur dioxide emissions from utility plant stacks has been accentuated by the ever-increasing public demand for elimination of all man-made air pollutants. I would like to describe the results of an investigation of the development of such a process; more important, I would like to present a discussion of the problems associated with the process which remain to be solved. The research work on the BCR catalytic gas phase oxidation process has been jointly sponsored by the Association of Edison Illuminating Cos., Edison Electric Inst. and Bituminous Coal Research, Inc., since 1958. However, work on SO2-pollution abatement was initiated by BCR in 1953. Tieman and Clymer,1 working with ozone and simulated flue gases, evaluated a gas phase oxidation process for removing SO2 from flue gases. Their experimental data indicated that the use of ozone to oxidize SO2 in flue gas concentrations, with subsequent recovery of H2SO4, did not appear to be economical due to the large ratio of ozone to sulfuric acid produced (2.6 to 1). The cost of the ozone would be 6 to 10 times the cost of sulfuric acid produced. As a result of the ozone study, work on a catalytic oxidation process was developed. The following reactions are the basis for the catalytic oxidation process Reaction [I] normally occurs in the combustion of sulfur-bearing fuels. At the high temperature found in the combustion chamber, 95% to 99% of the sulfur in the fuel is oxidized to SO2 and 1% to 5% is oxidized to SO3. The concentration of SO2 in the combustion gases depends on the combustion efficiency and the quantity of excess air used. A commonly used rule of thumb is 0.1 percent by volume SO2 in the flue gas for each 1% sulfur in the fuel. Reaction [2] proceeds at a wide range of temperatures. The rate of the reaction is rapid above l,000°F; however, the equilibrium conversion drops rapidly above this temperature. 2 Reaction [3] occurs rapidly to completion at temperatures below 400°F; above this temperature some SO3 exists in equilibrium with H2SO4. Complete dissociation of H2SO4 occurs above 650°F.3 The simplicity of the proposed process provided added incentive to the development and evaluation of the various component unit operations. The advantages of the process were considered to be as follows: 1) no raw materials were required, 2) the unit operations were not radically new; and 3) a salable product, sulfuric acid, would be produced. The successful development of the process was contingent upon the solution of several major problems: 1) The development of a catalyst which would provide high catalytic activity at reasonable conditions of gas flow and temperature without causing an unacceptable increase in pressure drop. 2) The development of a high temperature dust collection system to provide clean flue gases to the catalytic reactor. 3) The complete recovery of the sulfuric acid produced in the process; the effluent gas must contain less than 20 ppm by volume of sulfuric acid. As of this date, the complete solution to these problems has not been achieved. EXPERIMENTAL Catalyst Development: The use of platinum and vanadium catalysts for the production of sulfuric acid by the treatment of dry gases containing 5% to 20% by volume sulfur dioxide has been known for many years. The application of the basic idea of catalytic oxidation of sulfur dioxide in flue gas concentrations was

Jan 1, 1965

By R. W. Armstrong, D. H. Feisel

Self-diffusion in pure crystalline solids has been described through extension of the Cohen and Tum-hull volume -fluctuation model originally proposed for diffusion in simple liquids. It is shown, for a number of crystalline solids, that the self-diffusion coefficient, D, obeys the relationship where a is the lattice spacing, v the Debye frequency, Z' the lattice-volume fluctuation per atom required for a diffusion jump, and (?V/Vo) the relative increase in the lattice volume resulting from thermal expansion between O°K and the temperature under consideration. The calculated value of Z' is dependent upon the difiusion mechanism and the lattice geometry. ThE need for an increased understanding of mass-transport processes in crystalline solids has resulted in much research to determine rates of self-diffusion.' For several metals (e.g., copper, silver, and iron), the experimental values of the self-diffusion coefficient, D, have been determined over a large interval of temperature and the accuracy of D has been investigated through repeated experiments. Also, a number of empirical and theoretical diffusion studies have established a rational basis for understanding the D values for the different elements.2"6 The empirical diffusion analysis by Sherby and simnad6 supplied the main stimulus for the present study. Sherby and Simnad, reviewing the self-diffusion data for a substantial number of pure crystalline solids, suggested that sufficient data were available to establish with some certainty the apparent intrinsic material properties which influence D. Without explicit regard for any mechanism of diffusion, these investigators obtained an empirical relationship for D which correlated the self- diffusion coefficient for each element with the melting temperature, crystal structure, and valence of the particular element. Their analysis is only unsatisfactory in that the effect on D of crystal structure is not very clear and the valence to be assigned to an element is not always straightforward. The present study is an attempt, from a very different viewpoint from that of Sherby and Simnad, to establish a basis for understanding the self-diffusion coefficients for crystalline solids. This analysis was undertaken for the purpose of developing a general expression for D which would explicitly depend on the mechanism of diffusion. The main result of the study is that diffusion in crystalline solids may be described in terms of a volume-fluctuation model which was originally proposed by Cohen and Turnbull7 to describe diffusion in simple liquids. The model appears to be useful for predicting self-diffusion coefficients in crystals. The following sections describe the volume-fluctuation model for diffusion, the application of this model to crystals, and the resultant agreement with experimental data. 1) THE VOLUME-FLUCTUATION MODEL FOR DIFFUSION Cohen and Turnbull7'8 developed their model for liquid self-diffusivity for the purpose of describing certain properties of liquids, glasses, and the liquid-glass transition. A hard-sphere model for the liquid structure is used. In this model, the size of a spherical molecule or atom is fixed for all temperatures by the interatomic spacing at the absolute zero of temperature. At any temperature above O°K, the atom is viewed as being contained within a larger spherical cage defined by the interatomic spacing of the atoms at that temperature. A random distribution of varying cage sizes is assumed to exist in the liquid. An individual diffusion jump occurs when the free volume of an atom (the volume of the cage containing the atom minus the volume of the atom) is large enough for the atom to jump out of its cage. With this physical picture of diffusion in liquids, Cohen and Turnbull derive the following equation for self-diffusivity: D=Doe-yv*/vf [1] where Do is the product of three factors which are the diffusion-path geometry, the diffusion-jump distance, and the velocity of the diffusing atom, v*

Jan 1, 1964

By E. R. Macgregor, J. Halpern

The kinetics of the reduction of cupric salts in aqueous solution by molecular hydrogen to metallic copper are described. The rate of reduction appears to be homogeneously determined and shows a marked inverse dependence on the hydrogen-ion concentration. Precipitation of copper is more rapid and complete in sulfate than in per-chlorate solution. A mechanism is proposed which accounts for this behavior. IN recent years a number of important hydro-metallurgical processes have been developed in which metallic salts in aqueous solution are reduced by gaseous hydrogen, usually at elevated temperatures and pressures, and thereby precipitated either in metallic form (e.g. Ni, Co, Cu) or as an oxide or salt of lower valence (e.g. VO, and VA).1 ; In connection with applications such as these, most of which involve heterogeneously catalyzed reactions, recent demonstrations"-" that salts of certain metals, e.g., Cu", Ag' , Hg" , and Hg,+ can activate molecular hydrogen homogeneously and thus catalyze hydrogenation reactions in aqueous solution, are of considerable interest. For example, cupric salts catalyze the otherwise slow homogeneous reduction of dichromate and ceric salts by hydrogen, i.e. Cr,O; + 3HL. + 8H1 ? 2Cr'- -- 7H,O [1] 2Ce ' ! H.. ? 2Ce" | 2H . [2] In perchloric-acid solution, where Cu" is not appreciably complexed, the kinetics have been found" " to be of the form -d [H,] _- k,[HJ [CU"]' dt -LCu+' l+ (k ,/k,) [H] [3] where, K = 1x10"' exp [—26,600/RT] 1, mole-' min-' ... [4] and (k ,/k,) - 0.25 at 110°C. This kinetic behavior suggests that the reaction proceeds by a mechanism involving the following sequence of steps kt Cu" +H1CuH' 4-HA [51 k., CUH + CU" ? + 2Cu f H' [GI 6Cu'+ Cr,07 + 14H'+ 2Cr- (¦ 7H,O + 6Cu" ['i] fast The catalytic activities of the undissociated cupric-sulphate and cupric-acetate complexes are somewhat greater (by factors of 6.5 and 120, respectively) than that of the simple hydrated Cu" ion.'" These considerations suggest that, in contrast to the other hydrometallurgical hydrogenation reactions, referred to previously, reduction of cupric salts in aqueous solutions by molecular hydrogen, should proceed homogeneously, and in the absence of an extraneous catalyst. This has already been demonstrated" for acetate-buffered solutions where the product of the reaction is a precipitate of cuprous oxide (Cu,O). In the present paper, an investigation of the reduction of cupric salts in perchloric-acid and sulphuric-acid solutions, leading to the precipitation of metallic copper, is described. Some results for the sulphate system, which is of considerable hydrometallurgical interest, have been reported previously by Ipatieff",' " and by Schaufel-berger' but these do not give a quantitative account, of the kinetics and mechanism of the reaction. Experimental The reduction experiments were conducted in the 1-gal, titanium-lined autoclave described in connection with earlier related investigations," " and using a similar procedure. The solutions were made up by dissolving known amounts of CP grade Cu(ClO,), and HC10, (or CuSO, and HISO,) in dis-tilled water. While in the autoclave, the solution was stirred and maintained at a constant temperature (±loc) and under a constant partial pressure of hydrogen gas. It was ascertained that the agitation (provided by two 3-in., four-bladed stirrers, rotating at 900 rpm) was adequate so that at no time was the rate of reaction limited by solution of hydrogen. During each experiment, samples of the solution were withdrawn periodically, allowed to cool, and the concentration of copper remaining in solution was then determined electrolytically. Some Cu' is formed during the reaction, but undergoes disproportionation when the solution is cooled to room temperature. For purposes of kinetic calcula-

Jan 1, 1959

By Douglas J. Harvey

The surface tension of lead-tellurium alloys (in the range 0 to 6.70 at. pct Te) ad lead-arsenic alloys (in the range 0 to 10.53 at. pct As) has been examined by the maximum bubble pressure method. The surface tension of high purity lead can be expressed over a range of temperatures (M.P. to 750°C) by the relationship = 512 — 0.133t. Arsenic and lellurium were both found to be surface active in lead. The surface excess concentration at 700°C was .found to be constant at 0.74 x 10-10 moles per sq cm for tellurium. The surface excess of arsenic at 700°C varied between 0.26 x 10-10 moles per sq cm at 0.16 at. pct to 1.5 x 10-10 moles per sq cm at 8.3 at. pet. The surface tension of lead has been investigated sporadically over the last 90 years. The first recorded study was made by Quincke1 who used a rather crude application of the drop-weight method. Hogness2 obtained the first reliable value for the surface tension of lead by measuring the pressure necessary to force the liquid metal from the end of a small capillary of known radius. Hogness gives the empirical formula: ?(surface tension)= 444 - 0.077 (l-327) which describes the relationship between surface tension and temperature ("C); This work was followed by that of Bircumshaw3 who applied the two-capillar maximum bubble pressure method of Sugden.4 The values published by Bircumshaw are in good agreement with those found by Hogness. Matuyama5 examined the surface tension of lead by the drop weight method. However, the values found are somewhat higher than those previously reported. More recent investigations by Greenaway6 and by Melford and oar' have resulted in data which are not in close agreement, but which are well within the expected range at most temperature levels. The study of the surface tension of lead alloys began with Drath and sauerwald8 who examined the lead-bismuth system. They found that the surface tension values of the alloys in this system deviated only slightly from the ideal mixture rule. Matuyarna5 examined the lead-antimony system. Bircumshaw the lead-tin, and the lead-indium system was studied by Hoar and Me1ford.10 The results of these investi- gations are summarized in Fig. 1. It may be seen that the data vary only slightly from the ideal mixture rule. As none of the metals studied and reported in the literature has a very interesting effect on the surface tension of lead,*the next logical step might be to examine the effect of metals of low solubility or nonmetals having some liquid solubility. Baes, and Kellogg11 have pointed out that the elements most likely to be surface active in liquid metals are ones of limited solubility in the liquid state and possessing weak intermolecular bonding forces in the solid state. Therefore, Group V, VI and VII nonmetals are most likely to be surface active. It was decided to examine the effect of a borderline metal, arsenic, and a nonmetal tellurium. Arsenic forms a eutectic with lead having a melting point of 290°C and a composition of 6.9 at. pct As.13 Pure arsenic sublimes when heated above 610°C. Even though alloying with lead lowers the vapor pressure, fumes containing arsenic are evolved at a very noticeable rate when lead-arsenic alloys are heated above 650°C. Tellurium raises the liquidus temperature of lead sharply to 904°C,14 the melting point of PbTe (lead-telluride). The solid solubility of tellurium in lead was determined by Greenwood and worner15 to be 0.0007 at. pct at room temperature. EXPERIMENTAL METHOD Surface Tension Measurement—The two capillary maximum bubble pressure method for measuring surface tension developed by Sugden,4 and used later

Jan 1, 1962

By J. L. Brimhall, R. A. Huggins, M. J. Klein

IN a recent paper1 it was shown that small additions of magnesium, copper, and oxygen decrease the stacking fault probability in plastically deformed silver. Correlation of :X-ray data with measurements of the twinning frequency and metallographic observation of slip lines indicated that this effect may be due to an increase in the relative stacking fault energy. It is the purpose of the present note to report experiments on these alloys of known stacking fault probability that relate to the stacking fault contribution to electron scattering in silver. There has been a considerable amount of disagreement in the literature concerning the contribution of dislocations to electrical resistivity in metals. Calculations relating to the scattering of conduction electrons by the dislocation core, its strain fields, and related effects have been made by several authors.2-5 In addition, experimental work on Cu,3,6-10 Ni,11 and Ni-Co alloys1:! has shown that dislocations in those materials exert an anomalously large effect on resistivity, this effect being related to the presence of extended dislocations. The problem of the scattering due to the stacking fault region between partial dislocations has been treated theoretically using several different procedures.13-'0 The results of these calculations show a wide range of predicted values, from rather large to completely negligible, due to the models and the approximations involved. Almost all of this work has been applied to the specific problem of scattering in copper. The more complete theoretical treatments depend rather critically. on the shape of the Fermi surfaces and the effective mass parameters. The scattering from stacking faults might therefore be expected to vary significantly from one metal to another. Unfortunately, sufficiently accurate information is not available .which would allow one to have any confidence in a theoretical prediction of the scattering in the case of silver. Resistivity measurements were made on small wire specimens of vacuum melted high purity silver and several dilute alloys. These measurements were made at approximately 20°C, with great care being given to temperature measurement and corrections. At such temperatures phonon scattering is significantly greater than imperfection scattering. However, the experimental technique was such that measurements on similarly treated samples were reproducible to better than 2.4 X 10-9 ohm-cm, which was satisfactory for this work. Values of the stacking fault probability and the increase in resistivity after severe plastic deformation are given in Table I. The increases in resistivity resulting from plastic deformation agree quite well with previous work on silver.14,21-26 In addition, it has been previously found that interetitials and vacancies in silver anneal out well below room temperature, so that the residual imperfection scattering in these experiments could be expected to be primarily associated with dislocations;. It is seen from the data in Table I that large changes in stacking fault probability are accompanied by differences in resistivity due to imperfection scattering of only a few percent. If the scattering of conduction electrons by extended dislocations is primarily due to the area of the stacking fault region independent of the stacking fault energy, and not the core and strain fields associated with partial dislocations, the resistivity increase should be proportional to the product of the dislocation density and the stacking fault width, as is the stacking fault probability. Therefore, the imperfection scattering caused by plastic deformation of the alloys should be considerably smaller than that found in the pure silver. Since this was not observed, these results sugegest the possibility that stacking faults do not themselves contribute appreciably to the electrical resistivity of silver deformed at room temperature. An alternative explanation of these observations is that the scattering by the stacking fault is roughly proportional to the stacking fault energy, rather than being determined by the total area of such faults. Sufficient evidence is not yet available to separate these two possibilities. This work was supported by the Office of Naval Research.

Jan 1, 1962

By H. M. Otte, A. G. Crocker

SLIP, twinning, stacking faults, and precipitates on well-defined planes in a crystal produce traces that are visible on either a polished or an etched surface. The purpose of this note is to establish the usefulness and limitations of the information obtained from such traces when determining the orientation of single crystals or grains in a polycrystal. Attention will be confined specifically to traces produced by octahedral planes in cubic crystals, though most of the remarks can be taken as more generally valid. The problem of determining the crystal orientation is completely solved in principle' and in particular for the special case under consideration.1'2 Tables are available3 in which the orientations can simply be looked up when given the two or three angles between the traces. Thus a quick and simple method is available for obtaining the orientation of a crystal from surface traces. In this note two examples will be given from recently published papers and will show the use of the method with the aid of the Tables, as well as some of the precautions that should be taken in the procedure. As part of an analysis of X-ray Kossel lines, Peters and Ogilvie 4 determined from them the crystallographic orientation of the specimen. They chose a Cu-5.10 wt pct Si alloy that had been partly transformed from the a (fee) phase to the k (hcp) phase. The latter formed as very straight platelets along the octahedral planes of the a phase, and a photograph (Fig. 7 of Ref. 4) was reproduced in the paper4 of the region for which the orientation had been determined from the Kossel lines. Apart from a very small area (about 0.15 mm diam) near the top center of the photograph, the region shown was clearly all of one orientation. Traces in four different directions were readily identified. Starting with the smallest angle and proceeding counterclockwise, the angles between the traces were measured to be 27° 43', 55° 16', 64 3 43 1, and32"26'. These add up to 1802 08 1, indicating a cumulative error of 8'. The correct values should, of course, be taken from the original glass plates, or at least from prints on distortion-free paper, so the precision of the quoted values is actually greater than their accuracy. The solutions can be looked up in the Tables3 in four ways, depending on how the angles are paired, tion for the minutes of arc is required and the solution obtained will be identical for all the four pairs if the values of the angles are not in error. In a practical situation, such as this one, there are several sources of error, so that the four solutions obtained will all be slightly different. An arithmetic average of the four solutions is mathematically incorrect, but may, in special cases, give an answer close to the correct one. A rigorous procedure for refining the orientation has been described by Mackenzie;5 he gives a least-squares method that can be applied, if necessary, to this type of problem. The orientation thus determined can be compared with the one from the Kosel lines and discrepancies larger than the experimental error assigned to nonor thogonality of the X-ray or electron beam to the specimen. Here the example will only be used to illustrate the general procedure for making a very rapid rough check. From measurements on the stereographic projection, Fig. 9 of the paper,4 we can determine that the surface normal is approximately (0.434, 0.704, 0.562). From the Tables3 we find, using 28°, 55" as a good approximation to the first pair (27°43', 55°16'), that the surface normal is (0.453, 0.678, 0.579).* These two values are within 2 deg of each

Jan 1, 1967

By M. J. Pool, P. J. Spencer, R. V. Miner

The partial molar heat of solution of rhodiunz in liquid lin and Rh-Sn alloys has been measured as a function of rhodium concentration at 700" , 725" , 750" , and 775°K. The values at infinite dilution are very exo thermic, ranging from -29,950 to -28,260 cal per g-atom Rh at 700" and 775"K, respectively. At the solubility limit the heat of solution becomes sharply nzore exothermic and has permitted the liquidus boundary to be accurately established at each temperature. From the measurements in the two-phase region of liquid Plus RhSn, the heat of formation of RhSn,has been determined. A large increase in the heat of formation between 725" and 750°K suggests the possibility of a phase transformation in this compound. V ERY few measurements have been made of the heats of solution of transition metals in liquid tin; yet those values that are available are of great interest because of their very large exothermic nature. For example, the heat of solution at infinite dilution of palladium in tin has been measured as about -26,000 cal per g-atom (625" to 800°~),' while the heat of solution at infinite dilution of platinum is even more exothermic at -28,591 cal per g-atom (914°K).' These values are of the same order of magnitude as the heat of formation of many intermetallic compounds and as such clearly indicate that very strong bonding must exist between the solute and tin atoms in the liquid solutions. Rhodium might be expected to display similar solution characteristics in tin in view of its close electronic resemblance to palladium and platinum. Since no thermodynamic data are available for Rh-Sn alloys, rhodium was chosen as an appropriate solute for further investigation of transition-metal systems with highly exothermic heats of solution at infinite dilution. EXPERIMENTAL The heat of solution of rhodium in dilute Rh-Sn liquid solutions was measured as a functlon of rhodium concentration at 700°, 725", 750°, and 775°K. The liquid-metal solution calorimeter used in this work has been fully described elsewhere. At the start of each series of measurements, the solvent bath consisted of about 0.5 g-atoms of 99.9+ pct pure tin. To this was made a number of small rhodium additions, about 0.0005 g-atoms each, and the heat of solution was measured for each. Rhodium of 99.9+ pct purity in powder form was used in order to promote rapid dissolution in the liquid tin. The powder specimens were contained in tin foil stated to be purified (lead-free). This foil was found to have no measurable heat of solution in pure tin so the effect of any impurities could be neglected. The energy equivalent of the calorimeter was experi- mentally determined by dropping tungsten and/or tin specimens at intervals during each series of rhodium drops. The tungsten and tin used were 99.95 and 99.999+ pct pure, respectively. The only heat effect due to a tungsten drop, or a tin drop at low rhodium concentrations in the bath, is the sensible heat of the specimen. The heat content of these materials is well-established and is presented in the compilation of Hultgren et al. 4 As the rhodium concentration in the tin bath increases a small heat effect arises from the reaction: Sn (liquid, T) — & (soln, T) where T is the temperature of the tin bath. Where necessary, this heat of solution of tin was determined by Gibbs-Duhem integration, and corrections were made to the heat effect of the tin calibration specimens and the tin foil containing the rhodium specimens. RESULTS AND DISCUSSION The calculated values of the heat of solution of rhodium in dilute Rh-Sn alloys as a function of composition are shown graphically in Fig. 1. The values have been corrected for the sensible heat of the specimens, initially at 273"K, and apply to the reaction:

Jan 1, 1969

By D. F. Gibbons

THIS investigation was undertaken in order to gain further information on the mechanism of plastic deformation of iron at temperatures between room temperature and 77.2°K, and also to contribute to our understanding of the low temperature brittleness phenomenon that occurs in both the tensile and impact tests. It was decided to study as pure an iron as possible and to use the tensile test in order to simplify the problem as much as possible. Two series of iron were used throughout the investigation: iron A, obtained from the National Research Corp. and supplied as gas-free, high purity iron; and iron B, obtained from Fast' and produced by melting iron under purified hydrogen. Typical analyses of samples of both irons, after fabrication, are given in Table I. The main difference in composition of these irons is in their nickel and oxygen contents. Nickel has a very large solid solubility in iron. However, oxygen has an extremely small solid solubility. An attempt was made to reduce the oxygen content still further by remelting under purified hydrogen. This was successful in reducing the oxygen content to -0.0006 pct. However, no results on tests of this iron are included, since difficulty was encountered in fabricating the ingot. Wire specimens 1 mm in diameter were used for the investigation. The wires were produced from the ingots, as supplied, by cold rolling and swaging, with intermediate vacuum anneals at 700°C. Care was taken to reduce preferred orientation in the wires to a minimum by keeping the percentage of reduction in area between anneals of 30 to 40 pct. X-ray transmission photographs showed no indication of preferred orientation. The final grain size of iron A was 20 to 24 grains per linear mm and of iron B, 16 to 18 grains per linear mm. All specimens were tested in the decarburized and denitrided condition unless otherwise stated. The procedure was to pass hydrogen, saturated with water vapor at 26oC, over the specimens at 730°C for 2 hr. The specimens were quenched in iced water and then annealed in a vacuum of - 5x10-6 mm Hg for one day at 560°C to remove hydrogen. Higher temperatures were used for the vacuum anneal but this temperature was found to be quite satisfactory in removing hydrogen. The specimens were slow-cooled after the vacuum anneal. Where it is stated that the specimens were carburized, the specimens were given an identical decarburizing treatment and then carburized by passing hydrogen, saturated with pure n-heptane vapor at 0°C, over the specimens at 730°C. The specimens were then homogenized at 730°C for 2 hr in dry hydrogen. After the carburizing treatment the specimens were given the same vacuum anneal as for the decarburized specimens. The carbon content was determined from the maximum value of the internal friction carbon peak.2 Apparatus Fig. 1 shows a diagram of the tensile apparatus, with half the cooling coil removed. The cooling coil enabled temperatures from 200" to 77.2oK to be obtained. The apparatus was designed to fit a standard Tinius Olsen Universal tensile machine. The apparatus consisted of the rigid plate A which carried two carefully machined hooks H. These hooks attached the plate firmly to the moving crosshead of the tensile machine. The lower grip B was rigidly suspended from the plate A by three stainless steel rods. The upper grip C was joined to the upper grip of the tensile machine by the stainless steel rod E. The lower part of the apparatus was surrounded by a Dewar vessel, which was made a sliding fit inside the brass collar D. The specimen was held in a clamp which fitted into the grip, forming a ball and socket joint (see inset a). This was to attain as nearly pure

Jan 1, 1954

By E. A. Hopkin

Laboratory tests conducted by the author. together with actual field experience in Canada. have indicated the magnitudc of some of the factors affecting ability of drilling mud to clean the hole. A correlation was observed between funnel viscosity and particle slip velocity. A relationship was also observed between the Bingham yield value of the mud and the particle .slip velocity. Laburatury tests indicated little change in slip velocity with funnel viscosities up to ahout 80 sec/qt or to yield values of aboul 15 lb/100 .sq ft. The lip velocity of the partic1e.s. studied vuried from 160 ft/min with water to neerly zero for high mud viscositie. lncreasing the mud density, creating laminar annular mud flow or rotating the drill pipe Mlay also improve the carrying capacity of mud. Field tests indicated that during fast upper-hole drilling, the rate of cutting removal must he sufficien to maintain the concentration of cuttings in the annulus at less than 5 percent by volume to prevernt balled-up drill collars and .stuck drill pipe. INTRODUCTION In the Mid-Continent area, hole cleaning during rotary drilling normally involves the use of low-density drilling muds with funnel viscosities varying from 26 to 80 sec/qt. However, frequently it is necessary to raise the mud viscosity in excess of 200 sec/qt to clean the hole. In addition, field experience has indicated that during very fast upper-hole drilling, annular mud velocities considerably in excess of the maximum slip velocity of the cuttings (normally considered to be 120 to 150 ft/min) are necessary to prevent balling the bit and drill collars. In view of these variations in mud properties and circulation rates necessary to clean the wellbore, a study of factors affecting hole cleaning and the relative magnitude of each was undertaken. The study was also prompted by the knowledge that a drilling mud with properties close to those of water would drill at rates several times that of a viscous mud. The carrying capacity of these near-water muds was not clearly understood, however, and many drillers were reluctant to use them. DISCUSSION EFFECT OF MUD PROPERTIES ON DRILLING RATE The effect of mud properties on drilling rate has been studied by a number of investigators. 1t is clear from their work that mud properties close to those of water will significantly improve drilling rate and bit life. If the water-type mud will also effectively clean the hole and cause no logging or formation impairment problems, the choice of an appropriate drilling fluid is clear—use water. Often, however, a water-type drilling fluid is not capable of effectively cleaning the hole. THEORY OF PARTICLE SETTLING The forces acting on a particle that is allowed to settle through a fluid quickly reach equilibrium, and the particle settles at some constant velocity referred to as the slip velocity. The slip velocity of any particle depends upon a number of factors such as density and viscosity of the fluid, the volume, specific gravity, shape and roughness of the particle, and upon the shape and area of the projected face of the particle at right angles to the direction of relative fluid solid movement. Brown' expressed this relationship for spheres in Newtonian fluids in the following equation. where v, = slip velocity D, — diameter of sphere p, = density of spheye p, = density of liquid /a = friction factor g = constant. The friction factor f, varies as the size, shape, surface roughness and slip velocity of the body, and as the density and viscosity of the fluid varies. WaddelV ound experimentally that where dynamic similarity exists. f, was a function of the particle Reynolds number (NRe) of the sphere (Fig. 1). Fig. 1 shows that f, for spheres varies from over 10 for low NKe numbers to 0.44 for N,,. over 600.

By F. Gordon Smith

ALTHOUGH several geological indicators of the critical type are known, including quartz inversions and decomposition of hydrous minerals such as serpentine, there are very few of the general type. Solid solutions are excepted, but the limitations of use are very restricted and interpretations are sometimes ambiguous. General methods for determining temperature and pressure conditions during the crystallization of minerals would have considerable scientific and economic value. It is not the purpose of this paper .to, discuss the various methods of geological thermometry and barometry, but to present one general method, applicable to all minerals, and to describe what progress has been made in the methods of measurement. The general method, in. brief, is a study of the stress conditions in and around various types of foreign inclusions which are trapped in minerals during growth. The method depends upon the fact that any homogeneous gas, liquid, or solid will in general have coefficients of thermal expansion and volume compressibility different from those of any given mineral. Therefore stress must develop in and around all types of inclusions in minerals if the temperature or the pressure, or both, are changed from the conditions which prevailed during the growth of the mineral. The methods of measurement consist of determinations of the temperature-pressure conditions of fit of the inclusions in the host mineral. The types of inclusions in minerals are: 1-gas, or liquid plus vapor, when observed at room temperature, due to crystallization under pneumatolytic conditions; 2-liquid, or liquid plus vapor when observed at room temperature, due to crystallization under hydrothermal conditions; 3-glassy solid, or devitrified glass, due to crystallization under magmatic or high temperature metamorphic conditions, in a siliceous liquid; and 4-crystals, due to overgrowth of other minerals crystallizing simultaneously or of other minerals which crystallized previously. A survey of the literature shows that much valuable earlier work on inclusions, especially that carried out in England in the last century, has dropped out of current knowledge. The following is a brief summary of the significant, contributions to the problem up to the present day. Davy in 1822 asserted that fluid inclusions in minerals consist of an aqueous solution of salts and a gas bubble, the whole being either at lower or higher pressure than atmospheric.1 At intervals from 1823 to 1862, Brewster contributed information concerning other types of inclusion consisting of 1-aqueous solution, a much more expansible liquid, and a gas; 2-aqueous solution, salt crystals, and a gas; and 3-the very expansible liquid and a gas. The very expansible liquid fills the gas space between 20° and 30°C. Compression strain effects were seen around inclusions in diamond, topaz, and other minerals.2-6 Sorby in 1858 and 1869 further advanced the study begun by Davy, stating that fluid inclusions represent a sample of the mother liquor of crystallization and that the degree of filling of aqueous inclusions at room temperature defines the temperature-pressure relations during formation of the host. The degree of filling may be measured by determining the minimum temperature of filling of the inclusion by the liquid phase. The very expansible liquid in some fluid inclusions is liquid. carbon dioxide. The temperature at which salt crystals in fluid inclusions completely dissolve in the fluid is the minimum temperature of formation. Inclusions of glass or devitrified glass indicate crystallization from a melt. Inclusions of crystals in minerals are often centers of strain, which may be seen by optical effects or by radial tension cracks. Sorby realized that an analysis of stress-strain relations about inclusions could be used to provide precise data on the temperature of crystallization, but the matter was never pursued.7,8 Hartley (1876, 1877),9,10 Hawes (1881),11 Wright (1881),12 Johnsen (1920),13 and Holden (1925)14

Jan 1, 1952

By S. A. Bradford

Internal-oxide precipitates in decarburized a iron alloys were studied by microscopic and X-ray methods. Diffusion of oxygen is primarily trans-granular, although large amounts of manganese or PhosPhorus cause preferred grain boundary dimsion at temperatures below 1450OF. Transgvanular internal oxidation follows the parabolic rate law with an apparent activation energy of 60 kcal per g-atom for decarburized rimmed steel and around 50 kcal per g-atom for higher alloy contents. The internal oxide is (Fe,Mn)0. Evidence was found for a miscibility gap in the FeO-MnO system. UNTIL very recently, the internal oxidation of metals was studied primarily as a scientific curiosity or, in a few cases, as a means of strengthening alloys by precipitation hardening. However, with the recent development of low-carbon enameling sheet steel, internal oxidation has become a problem of practical importance to the steel industry. For example, in 1961 it was reported1 that internal oxidation of steel can occur during decar-burization by open-coil annealing and will reduce the notch ductility of the sheet unless the process is carefully controlled. The present study was therefore undertaken to learn more about the rates and mechanism of oxygen diffusion and oxide formation in iron alloys. BACKGROUND The process of internal oxidation has been well-defined in the literature:',' oxygen dissolves in an alloy, diffuses inward from the surface of the metal, and reacts to form a precipitate with the alloying element that will provide the most stable oxide. he growth of the finely divided so-called subscale, i.e., the internal-oxidation zone, depends on the diffusion rates of both the oxygen and the reactive element.4 Investigators have generally found that increasing the temperature increases the size of the oxide particles, the rate of subscale growth, and the tendency to transgranular diffusion. With very few exceptions, the square of the thickness of the internal oxide layer is directly proportional to the reaction time. Given two conditions easily satisfied for iron systems— a) an oxygen solubility much less than the concentration of the alloying metal and b) an oxygen-diffusion rate to the oxide boundary much faster than that of the alloying element—then the general expression developed by Rhines and co-workers5 for the parabolic growth rate of the internal-oxide zone can be simplified to the following form: where Co and CM are, respectively, the solubility of oxygen and the concentration of the alloying element, DO is the diffusion coefficient of oxygen, O/M is the weight ratio of oxygen to metal in the precipitated oxide, and x is the thickness of the internal-oxide zone after an annealing time t. Both the oxygen solubility and diffusion coefficient can be approximately expressed as functions of temperature by Arrhenius-type equations: in which H and Q are, respectively, the heat of solution and the activation energy of diffusion. Consequently, the apparent activation energies calculated from Arrhenius plots are the sum of the heat of solution of oxygen in iron and the activation energy for diffusion of oxygen. The data, if not the interpretation, of Schenck et al.8 bear out the fact that oxygen diffuses in the atomic form. The general rate law for atomic diffusion is: the reaction rate being proportional to the square root of the pressure at low pressures. Benard and Moreau8 studied both the surface oxidation of Fe-Ni alloys and the gradual penetration of oxygen into the metal. They observed that oxide particles first form along grain boundaries and then grow to form continuous films that eventually envelop the grains. The parabolic rate law does not usually apply in these cases, especially at the higher temperatures. The oxide formed is wustite which gradually transforms into Fe3O4 and finally into Kennedy and coauthors8 examined Fe-Ni alloys with 26, 75, and 84 pct Ni oxidized at 800°C and

Jan 1, 1964

MODERN mining is based on drilling--everything else stems from that. U. S. and Canadian mining companies and suppliers of mining equipment are constantly seeking new techniques and tools for increased drilling efficiency. Ultimate goal is increased bit-against-rock time. Just how important their efforts are can be seen through a legitimate extension of available statistics. In Canada some 70 million ft of drilling per year is required. While the number of feet actually drilled in the U. S. is unknown, it is possible to compare U. S. and Canadian mineral production, excluding oil and coal. In the U. S. mineral value was $4200 million and across the border $836 million. Taking into account the number of drilled feet required to produce Canada's total, the U. S. total would be 365 million ft in 1953. A saving of 14 per ft would reduce over- all metal and nonmetal mining costs some $3.65 million per year. This does not take into account other indirect savings. Methods have changed and there have been structural and metallurgical advances in blasthole practice in the last ten years. The Editors of MINING ENGINEERING in the articles on the following pages present the most significant innovations coupled with results in the field. Environment plays an important role in selection of materials and equipment -but while unanimity does not exist throughout the industry in reference to drilling problems, a definite trend is evident. For the story of that trend read the articles on the following pages.

Jan 9, 1954

In 1975, the US produced 10 900 tons (12,000 st) of U3O8 from ores whose grade ranged from a low of 0.160% to a high of 0.196% U3O8. By the early 1980's if the current mining projects described here are allowed to go on stream, Australia will be able to produce at least 10 900 tons of U3O8 annually from ores whose grade ranges from a low of 0.150%to a high of 2.300%. As pointed out in the previous article, this initial rate of production could have been reached now-giving an immense boost to the depressed Australian economy. So, let's have a close look at current mining projects.

Jan 1, 1977

By Howard S. Strouth

Investors and mining companies in the U. S. have recently shown increased interest in the Union of South Africa. This has been sparked partially by the founding in the U. S. of a large investment trust which will hold substantial shares in many of the leading gold and uranium producers. The average U. S, mining man's judgment of the Union, however, may be somewhat clouded by recent headline news. We are inclined to take a strong dislike to the stern measures of the present Union government with regard to its native majority. Others possibly think of South Africa in krms of a British colony which, under pressure of rising African nationalism, must eventually be abandoned. These concepts frequently suffer for lack of precise information.

Jan 5, 1959

The ten-year "supply-demand relationship" tables in this chapter for various mineral and metal commodities have been adapted from Minerals in the U.S. Economy, compiled by the Bureau of Mines, U.S. Department of the Interior, published in 1975. Acknowledgment is made to the Bureau of Mines for compilation of the tables. [ ]

Jan 1, 1976

By D. L. Katz, M. J. Rzasa

The derivations of three methods of computing the static pressure gradients in natural gas wells have been presented to show the assumptions made. Charts were developed from which the pressure gradients may be read when the well-head pressure, the well fluid gravity, depth, and the average well temperature are given. A chart for estimating the well fluid gravity from the condensate content and separator gas gravity is included. The effect of the increased average well temperature after flow on the calculation of the static pressure gradient is discussed. Introduction Reservoir pressures have been calculated from well-head pressures for gas wells for many years. As the pressure measurements become more accurate, the need for a reliable calculation of the static pressure gradient often arises. This paper will develop the several methods for computing the pressure gradient in gas wells and make a comparison between them. The method of calculating static pressure gradients in common use is Eq. I (ref. I) or its counterpart which includes a factor for the deviation of the gas from the ideal gas law. P2 - P1 = P1(e0.0000347GX _ I) Eq. [I] in which P1 = pressure at well head, lb. per sq. in. abs. PP = pressure at bottom of well, Ib. per sq. in. abs. G = gas gravity X = depth of well, ft. An alternate method is to compute the average density of the gas in the well and multiply by the well depth in a manner similar to that used for liquid gradients. Derivation of Formulas A static pressure gradient is a special case of the general fluid-flow equation. Consider a pound of fluid flowing in a vertical column from point I to point 2, Fig. I. By an energy balance for fluid flowing from I to 2: U1 + P1V1 + u12/2g + X1 + q = U2 + P2V2+ u22/2g+X2 +W [2] in which U = internal energy, ft-lb. per lb. P = pressure, lb. per sq. ft. V = volume, cu. ft. per lb. u = average linear velocity, ft. per sec. X = height above datum, fl. q = heat absorbed by fluid, ft-Ib. pcr lb. W = work done by system, ft-lb. per lb. An energy balance on the fluid itself gives: U = ?TdS - ?PdV + etc. [3] in which T = temperature, deg- R- S = entropy, ft-lb. per deg. R. per lb.

Jan 1, 1945

By A. E. Dwight, A. F. Berndt

ThE published U-Ru equilibrium diagram indicates the existence of six intermetallic compounds in this system.' The structure of only two of the compounds, u2Ru2,3 and URU3,4 have been identified. This communication reports on the crystal structure and density of Uau3, which is formed by a peritectoid transformation at 1025° ± 5°C: U3Ru4 + U3Ru5 = U2Ru3. An alloy with the stoichiometric formula U2Ru3 was prepared by arc melting electrolytic uranium and ruthenium of 99.9 pct purity on a water-cooled copper hearth under an argon atmosphere. After homo-genization at 1000°C for 3 days, a metallographic examination revealed that the peritectoid transformation was complete and less than 5 pct of a second phase was present. A powdered sample, obtained by crushing the brittle compound, was annealed for 1 hr at 1000°C and air-cooled. Debye-Scherrer patterns were obtained with filtered CrKa, FeKa, CoKa, or CuKa radiation. The X-ray patterns of U2Ru3 weFe indexed as an fcc structure with a. = 12.895 0.00lA. The unit-cell constant and its standard deviation were calculated by a computer program described by Mueller, Heaton, and Miller.5 The density, measured by an immersion method, was 14.45 g cm-3. A calculated density of 14.48 g cm-3 was obtained on the assumption that twenty-four formula units (120 atoms) comprise a unit cell. The space group is either oh7 Fd3m, or the less symmetric, T4h, Fd3, since reflections indexed as hk0 with h + k + 4n are absent. All values of h2 + k2 + 12 permitted by both space groups are listed in Table I together with dc, do, and I. values. The calculated d spacings were obtained by the computer program of Mueller, Meyer, and simonsen.6 The observed d spacings above 0.77A were obtained from X-ray" patterns prepared with CuKa radiation, above 0.90A with CoKa radiaaion, above 0.98A with FeKa radiation, and above 1.16A with CrKa radiation. An attempt was made to identify the crystal structure of U2Ru3 by comparison with published data on other A2B3 compounds. A recent compilation7 of intermetallic compounds lists thirty-two structure types with the A2B3 stoichiometry. Only two of the structure types are fcc and they are Sb2O3(r), senarmontite, with 16 Sb2O3 per unit cell, and In2Te3 for which several structures have been proposed.8 However, the two cases cited do not have twenty-four formula units in the unit cell. We therefore, cannot identify UPRU3 with any of the other known A2B3 compounds. Ternary alloys were made in which 5 at. pct Os, Rh, or A1 were substituted for 5 pct of the Ru in U2Ru3. The osmium substitution increased the unit cell constant to 12.899 * .001A, which is to be expected since the atomic volume of osmium is slightly larger than

Jan 1, 1969

By W. C. Meyer

In an effort to conserve and extend oil resources, the use of powdered coal-in-oil mixtures (COM) as an alternate fuel in oil-fired boilers is receiving increasing attention. For the approach to be successful, some degree of stability of the suspension against settling is needed. The variety of means available to achieve stability of this nonaqueous slurry is reviewed along with some of the physical and chemical concepts which underlie each method.

Jan 1, 1983