Search Documents

By Kazuya Nakabo

In this article, influences of restraint and MgO content on densification of alumina-magnesia castable during heating were experimentally studied. High thermal expansion-alumina-magnesia castable specimens were surrounded by low thermal expansion-alumina-silica castables, and heated in an electric furnace. Doing so allows restrained heating of alumina-magnesia castable. According to the results of simple calculations, the restraint stresses were estimated to be between 2 to 20 MPa, so the experimental conditions were considered reasonable. As a result of the experiments, it was verified that restraint densifies alumina-magnesia castable, resulting in an increase in modulus of rupture and modulus of elasticity. The densification effect of restraint became larger as the MgO content increased. The effects are attributable to an in-situ spinel forming reaction, which improves corrosion resistance.Taking the temperature distribution in the castable lining into account, large restraint stress is expected for the hot face while only a little effect is expected for back end. Thus, excessive difference in material property in the thickness direction, which is undesirable in terms of structural spalling, is a concern.Hence, the MgO content of alumina-magnesia castable should be determined carefully, taking not only corrosion resistance but also spalling resistance into consideration.

Oct 30, 2017

By Dagoberto Brandão Santos, Kairo de Barros Guimarães, Túlio Magno Füzessy de Melo

The effect of the cooling conditions on the microstructure and hardness of a Dual Phase hot-rolled steel 800 MPa strength was investigated. Simulations of the cooling conditions using a dilatometer were carried out from samples of a hot rolled coil with variations of the intermediary temperature from 620 to 740°C, isothermal holding time between 1 and 10 s and coiling temperature between 50 and 400°C. In addition, two CCT (Continuous Cooling Transformation) diagrams were developed to evaluate the effect of the isothermal holding time on the phase transformations of the remaining austenite. It was observed that the intermediary temperature has a strong influence on the kinetics of the phase transformation, as well as the isothermal holding time influences the amount of ferrite formed and, consequently, the final microstructure and hardness of the material. The coiling temperature did not cause significant changes in the amount and morphology of the ferrite, but a gradual replacement of martensite with bainite was observed, which, in addition to the self-tempering effect, contributed to the hardness reduction.

Oct 1, 2019

By Fábio Dian Murari, Antônio Adel dos Santos

The effect of reheating temperature of slabs on the precipitates dissolution and mechanical properties of Ti-Nb microalloyed steel was investigated in pilot scale. It was verified, by means of transmission electron microscopy, a significant decrease in precipitates formed during the solidification of the steel as the reheating temperature increased from 1100°C to 1200°C. No significant changes in size and shape of the precipitates were observed with further temperature increase up to 1280°C. In line with the precipitates dissolution behavior, an increase in strength was observed with the elevation of the reheating temperature up to 1200°C, due in part to the reprecipitation of fine Nb-rich precipitates during the hot rolling. At 1200°C the presence of deformed ferrite on the microstructure contributed to the additional increase in strength. After reheating above 1200°C up to 1280°C, a decrease in strength of the rolled plates was noticed. This effect has been credited to the absence of deformed ferrite grains and also to a small increase in the low angle grain boundaries size. The results were in agreement with Thermo-Calc and Dictra simulations.

Oct 1, 2019

By Douglas Glenn Stalheim

The demands for improved mechanical properties in hot rolled long products are increasing as the expectations of global Standards and construction designer’s increase. Cost constraints limit the excessive use of expensive alloys to meet these expectations. In addition, depending on the mill, equipment can limit what can be realized to meet the increasing expectations. The most effective way to meet the increasing expectations for improved mechanical properties of optimum strength and ductility is through producing steel with as fine as possible uniform cross sectional grain size in the “as-rolled” condition. The best solution to the development of this fine and uniform cross sectional grain size is to develop a cost effective alloy design coupled with proper metallurgical process control implemented into an existing mill’s equipment capability and layout. In other words, properly bringing together alloy, metallurgy, process control and existing equipment capabilities to develop an optimum product that can meet the increasing demands of the construction designer. This paper is designed to give a solid understanding of the production and metallurgical requirements to achieve a grain size in “as-rolled” long products that is as fine as possible within the limitations of the process and production parameters of the individual plant.

Jul 30, 2018

By Liao Jianfeng

The Baosteel Zhanjiang 5,050m3 blast furnaces have been built with highly independent integration and innovation technologies and represented the state of the art of the world’s huge BFs. The proper of BF1 and BF2 is designed with long-campaign technology; both BFs share the same set of stockhouse, water and PCI systems; the BCQS serial-hopper no-bell top, TRT and blower are all local equipment as applied; four top-combustion stoves systems are matched; the BFG is cleaned by fully dry process; and the automation control system for the main process is self integrated. The BFs have been started up and performing with sound indicators. Their smooth proceedings symbolize China’s huge blast furnace ironmaking technology ascending a new high.

Oct 30, 2017

By J. Bas A. F. Smeulders

Traditional laboratory lubrication tests, including those for cold rolling lubricants often involve measurement of neat oils. To achieve increased levels of test severity, such tests are often carried out at high temperatures and prolonged durations. However, we found that the levels of lubricant degradation and wear in these tests can be much higher than in the field. Moreover, steel rolling is not done with neat oils, but with emulsions, where the presence of water influences film formation, surface chemistry and oil composition in the roll bite. To better approach the situation in the field, and thus to be able to develop rolling oils with improved lubrication performance, several lubrication tests were developed for emulsions: direct measurement of film formation and measurement of Stribeck curves, in which the emulsions can be assessed in terms of their boundary lubrication and elastohydrodynamic behaviour. The key innovation is that also another test method was developed, which focuses on boundary lubrication and wear, and the role of extreme pressure and anti-wear additives. Realistic levels of test severity are achieved in the tribometer by mimicking frictional power intensities and flash temperatures for typical cold rolling or tinplate mills. Test conditions can be adapted according to the mill stand or pass number and other cold rolling process parameters. The emulsions are kept at normal operational temperature. Clear differences could be observed between emulsions of various concentration and composition. The viability of the method is illustrated by a number of field cases, in which a good correlation is demonstrated between the laboratory tests and the performance in a pilot or production mill.

Jul 30, 2018

By John Ross Middleton

Based upon 30 years+ experience in the Development, Implementation and Ongoing Support of Computer based Melt Shop Management Systems in about 40 plants in the UK, Europe and the USA, consideration of the overall facilities of a state of the art, comprehensive, Integrated Melt Shop System covering Melting and Secondary processes for all grades of steels and superalloys; the scope of functionality of these systems, covering Raw Materials and Consumables Procurement and Inventory Management, Laboratory Management, Melt Shop Scheduling, Furnace Charge and Additions Optimisation, Level 1.5 to Level 2.5 Materials Optimisation and Process Control Calculations, Process Data Recording, Management of Ladles, Furnace Bodies, Vessels and Moulds, Comprehensive Management Reporting and Integration with Corporate ERP Systems. The second section of the paper reviews the key ‘Success Factors’ to achieve rapid, successful implementation, comprehensive, fast response user support, continuing system improvement and maintaining ‘perfect fit’ of system to operations in an ever changing future technical, operations and business environment.

Jul 29, 2018

By Karl Berger

The paper gives a comprehensive overview of the historical development of various metal rolling technologies and also describes the influence to industrial and socio-economic developments. The rolling of steel, in particular of rails, beams, rebar, strip and plate has enabled the large scale transport and travel, the building of bridges and buildings, the manufacturing of ships and cars. All this has changed the face of the world significantly. Further the paper approaches technological highlights in the design, manufacturing, drive and control of modern mills and the various types developed to create industrial economic units for the different markets and customers’ requirements. An outlook of future challenges is as well discussed in the paper. Various solution approaches for the rolling technologies, from continuous improvement of existing plants to more radical new concepts like endless rolling, near net-shape casting and rolling are approached. A positive conclusion is drawn that rolling technologies will remain a valuable area for engineers with scientific and economic challenges, but also a clear vision for positive contribution to further industrial and social development.

Jul 30, 2018

By Luiz Antônio Fonseca Peçanha Júnior

As propriedades e caracteristicas do diboreto de titânio (TiB2) e nitreto de alumínio (AlN) tornam esses materiais ideais para aplicações termomecânicas. Entretanto, a dificuldade de sinterizar compósitos cerâmicos à base de TiB2 – AlN tem limitado suas aplicações na indústria contemporânea. Nesse sentido, o presente trabalho tem por objetivo avaliar a técnica de sinterização por plasma pulsado (SPS), como uma alternativa para consolidação de compósito cerâmico em um curto intervalo de tempo. Após a caracterização das matérias primas, as amostras foram sinterizadas utilizando temperaturas entre 1.500°C e 1.900°C, além de 80 MPa de pressão e 10 minutos de permanência na temperatura máxima. A técnica “SPS” mostrou-se eficiente na sinterização desse sistema, alcançando densificações de até 98%. E ainda, como era esperado, a incompatibilidade dos coeficientes de expansão térmica entre o TiB2 e o AlN provocaram um processo de tenacificação nos compósitos.

Aug 16, 2017

By Joaquim Luiz Monteiro de Barros, Fabiana Moreira Costa

Este trabalho tem como objetivo principal apresentar de forma didática e através de exemplo prático, os processos de limpeza de gases de exaustão durante a produção de ferro e aço para atendimento as normas ambientais e a possibilidade da recuperação de energia térmica desses gases captados para aumento da eficiência energética das plantas siderúrgicas.

Aug 1, 2019

By Hormando Leocadio, CWM van der Geld, Julio Cesar Passos

Impinging water jets promote high heat flux extraction rate. Steel industry widely employs the process for accurate temperature control to improve the microstructure and to ensure adequate mechanical properties. The range of surface temperatures, heat fluxes and cooling rates are very large, which makes it important to obtain an accurate value of the heat transfer coefficient. This paper presents an experimental and numerical study of the heat transfer behavior of a high temperature (450°C - 900°C) steel plate cooled by a water jet at 20°C to 70°C. High-speed imaging (up to 20,000 fps) within water jet impingement zone allowed the characterization of the boiling regimes in the early stages of cooling. The effects of initial temperature, water jet temperature and velocity on the heat transfer coefficient were analyzed by inverse heat conduction method that predicts the heat flux and temperature on the top surface from temperatures measured with thermocouples inserted in test plate. Heat transfer is strongly affected by the initial temperature of the hot steel, water jet temperature and, less intensely, by jet velocity. High cooling rates start when liquid water is in direct contact with surface temperatures above 700°C.The results will contribute to the enhancement of the temperature cooling control on the runout table and cooling model employed at Usiminas Hot Strip Mill.

Oct 1, 2019

By Bernhard Hiebl

Global trends that are constantly challenging the iron and steel producers are related to worsening of the iron ore grades, higher substitution rates of main iron ores to cheaper raw materials due to economic pressure and increased environmental standards. Changing the raw materials in an operating plant can significantly influence the sintering or pelletizing process. Adjusting all process parameters to regain stable and high productive operation takes considerable time and causes production losses. Furthermore changes in raw materials lead to variations in the process gas flows and emission concentrations.Therefore SVAI developed two models for numerical simulation of sintering process and pelletizing process. Amongst others the models are based on Ergun equation and include chemical reactions of the related process. For already operating plants the simulations shall predict changes of the process parameters when raw materials are exchanged or when operational parameters are varied. Furthermore the simulations give advantageous information for the design of green field plants and allow the simulation of different plant configurations.The objective of this paper is to demonstrate what the latest developments are in these numerical simulations and what Siemens VAI is doing to overcome the remaining challenges in this field.

Aug 2, 2018

By Andreas Jungbauer

Two Arvedi ESP plants going into operation in 2015 will allow a Chinese steel producer to better serve the extremely attractive local and export markets for high-quality, thin-gauge strip products. The energy consumption and the related costs are reduced by up to 45% compared to conventional casting and rolling processes. This also means a major reduction in CO2 emissions. The new plants are designed for an annual production capacity of 2 x 2.55 million tons of high-quality, ultra-thin, hot-rolled strip products with widths of up to 1,600 mm and thicknesses down to 0.8 mm. The project scope also features a comprehensive training and assistance package for plant start-up and operations by personnel from the existing ESP plant at Acciaieria Arvedi SpA, Italy. The plant setup, the trainings and assistance program as well as latest results from the ESP plant in Italy will be presented. While this project is under execution three further ESP lines have been ordered by the same customer summing up now to five ESP lines at the same location.

Jul 30, 2018

By Dr. Steven G. Jansto

The market demand for reduced fuel consumption and CO2 emissions in the automotive, energy and construction sectors have further increased the demand for new and advanced higher quality microalloyed grades produced via TMCP. The technological integration of the process and physical metallurgical advancements of value-added niobium (Nb) microalloyed thermo-mechanical controlled process (TMCP) steels continue to be developed and is an important element for these more demanding end user requirements and cost-effective steel production. The reheat furnace process step has a profound effect on the TMCP performance, final hot rolled steel quality and mechanical property consistency during the production of hot rolled steels. The uniformity of heating applied across the entire width, thickness and length of the slab or billet is essential in the successful achievement of consistent customer properties regardless of the chemistry. The resultant ferrite grain size in the final hot rolled product is significantly governed by the initial prior austenite grain size. However, the transition from laboratory melted and TMCP hot rolled heats to the production scale is often quite challenging. Aberrations in the reheating process step at the industrial furnace are often the root cause of mechanical property quality issues. These combustion process metallurgy parameters connect directly to the resultant TMCP product quality and is defined as Combustion Metallurgy

Oct 1, 2019

By Cleber Caetano Thomazi

Rotary kilns are continuous process equipment used on calcining of nickel ore. The chemical and physical reactions are created by means of heat up the material to predetermined temperatures. Tertiary air fans are attached to the kiln shell to maintain oxidizing/reduction conditions. Special ducts orientate the air flow inside the kiln. In the present work, two types of failure on distinct tertiary ducts mounted on the same kiln are reported. Chemical analysis, hardness test, metallographic and fractographic examinations were carried out. Fabrication related problems and creep were identified as the root causes of damages.

Oct 30, 2017

By Pedro Cunha Alves, Wagner Viana Bielefeldt, Vinicius Cardoso da Rocha, Augusto Lachini Pereira, Julio Aníbal Morales Pereira

The capacity of steelmaking slags (CaO-SiO2-Al2O3-MgO) on inclusion removal from liquid steel was investigated through experimental conditions. Laboratory experiments with slag and steel samples (with inclusion population known) were performed using a vertical electric resistance furnace at 1600 ºC. After the melting experiments, slag and steel samples were separated and analyzed regarding their chemical composition and inclusion population evolution. The capacity of slags on inclusion removal was evaluated based on the thermodynamics (solid and liquid phases proportion, phase composition and effective viscosity of slags) calculated using the FactSageTM 7.2. Results indicated that changes in the composition of slags (regarding CaO/SiO2 e Al2O3) presented effects on the steel cleanliness. The total inclusion density decreased in all steel samples and the removal of inclusions by slags shows a tendency to improve as their viscosity decreases (< 0.23 Pa.s).

Oct 1, 2019

By Franco de Castro Bubani

Cu-base alloys (Cu-Zn-Al, Cu-Al-Be, Cu-Al-Ni), depending on their composition, have martensitic transformations that can be thermally or mechanically induced between a metastable structure called austenite and one or more metastable structures called martensites. In single crystals, depending on the specific composition of the alloy and the crystallographic orientation of the tensile axis, martensite-martensite transformations can be mechanically induced. The hysteresis associated to these martensite-martensite transitions is usually much greater than the one associated to the austenite-martensite transformation. Thus, martensite-martensite transitions are potential candidates for energy dissipation in a mechanical damper. Possible applications that would benefit from high hysteresis include seismic damping devices, dampers for satellites and the aerospace industry, defense and others. We present pseudoelastic cycling results of alloys submitted to different thermal treatments. Our conclusions highlight the fact that, under certain conditions, Cu-base alloys deliver better damping performance than commercially available SMAs and even the new Fe-base SMAs.

Aug 7, 2018

By Elson Renato Santos Souza, Ricardo Pondé Weber, João Carlos Miguez Suarez, Sergio Neves Monteiro, Suzane de Sant’ Ana Oliveira

Foi estudado a influência do aporte térmico, de soldagem, sobre a resistência balística de um aço de alta dureza (HHA) temperado e revenido (HHA), utilizando o processo de soldagem a arco. O aço HHA, temperado e revenido, foi caracterizado por análise metalográfica, ensaios mecânicos e ensaios balísticos. Os resultados mostram que o aporte térmico da soldagem teve influência significativa nas propriedades mecânicas da Zona de Fusão (ZF) e da Zona Termicamante Afetada (ZTA), ocasionando mudanças na resistência balística. O melhor desempenho balístico do material soldado foi obtido para a soldagem de baixo aporte térmico.

Oct 30, 2017

By João Luiz do Vale

In standard wear tests, such as pin on disk (ASTM-G99) or block on ring (ASTM-G77), the apparatus simulates conditions that are often different from a machine element real application. Therefore, for an accurate investigation of a tribological application, it is essential to test the real condition in which there are similarities as: geometry, contact details, force application mode, materials, among others. It emphasizes that for studies involving polymeric materials it becomes extremely relevant. Thus, the Laboratory of Surfaces and Contact (LASC) at UTFPR developed an apparatus for sliding bearing on shaft test. In that equipment, loads are applied by a dead-weight system and the frictional force is measured on a load cell. The apparatus operating ranges for load added to the dead weight system and rotation shaft are from 0.2 to 5.0 kgf and from 260 to 3500 rpm, respectively. This paper presents a detailed evaluation of such apparatus, which includes free-body diagrams analysis and a deduction to obtain an equation for the kinetic friction coefficient. Also, the standard measurement uncertainties of a caliper, an electronic scale, and a cell load were determined. It was verified that the kinetic friction coefficient equation is dependent on the apparatus geometry, the applied load, and the frictional force value. Additionally, through the statistical significance analysis it was concluded that some terms in the equation were not significant. Finally, through the application of the error propagation theory in the kinetic friction coefficient equation, the standard measurement uncertainty of the apparatus which showed a value nearby 0.002 along the operating range of the apparatus was obtained.

Jul 31, 2018

By Juarez Linhares

A mini sinterização processo JL patenteada sob o número PI-9202973-6, é caracterizada por soprar o ar pelo fundo da panela, dispensando o uso de grelhas, caixa de ignição além de proporcionar um baixo consumo de energia elétrica, o que se traduz em vantagens técnicas e econômicas ao processo de sinterização.

Aug 16, 2017