Search Documents

By Singh RN

The Bulli Coal Seam, located in the Illawarra Coalfield of New South Wales, has a long and varied history of sudden outbursts. From available information this problem has resulted in twelve fatalities over the last one hundred and one years, with over five hundred separate outburst incidents being identified. These incidents have varied in severity and intensity from the discharge of 1 to 2 tonne of coal, with a slight increase in gas emission, to the discharge of 200 to 400 tonne of coal with some 6,000 m3 of gas being liberated and large items of mining equipment being pushed 1 to 2 metres down the roadway.Geological features associated with these outbursts can be mapped on a regional and mine by mine basis, to provide some indication or warning. Similarly changes in gas content and gas composition can also be determined on a regional and mine by mine basis. However sudden geological changes (such as a 6.5 metre seam displacement within 15 metres) variations in gas content (such as 6 m3/tonne to 15 m3/tonne) and changes in gas composition (from 95% CH4 to 90% CO2) all within one mine does make the prediction or forecasting of outburst incidents exceedingly difficult.

Jan 1, 1998

By H Ramandi, H Masoumi, I Canbulat, B Hebblewhite, J Oh, S Saydam, W Timms, S Mo

This paper reviews the floor heave mechanisms in underground coal mine roadways. Previous studies have reported three main failure mechanisms: bearing capacity failure, buckling and swelling. The buckling failure has been observed where immediate floor strata are relatively strong and thinly bedded. On the contrary, the weak floor strata have been associated with both the bearing capacity failure and swelling mechanisms. The bearing capacity floor failures are likely to induce other types of instability such as pillar punching, tensile failure of pillar, roof fall and subsidence as well as floor heave. Despite a considerable amount of research, predicting the magnitude, location and timing of floor deformation is challenging with current state of knowledge. CITATION:Mo, S, Ramandi, H, Oh, J, Masoumi, H, Timms, W, Canbulat, I, Hebblewhite, B and Saydam, S, 2018. A review of floor heave mechanisms in underground coal mine roadways, in Proceedings The Fourth Australasian Ground Control in Mining Conference (AusRock), pp 196–206 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 30, 2018

By Xianglin Yang, Hong Zhong, Jingjing Xiao, Guangyi Liu

"The selective adsorption of a flotation collector to a mineral plays a crucial role in enhancing the hydrophobicity of targeted mineral particles for attaching air bubbles in pulp. The recent progress of the structure-reactivity relationship of flotation collectors, the characterization methods for mineral surfaces with adsorbed collectors and their commercial application are reviewed in this paper. Particular emphasis is placed on the density functional theory (DFT) for understanding the reactivity of new collectors, the surface analysis techniques including time-of-flight secondary ion mass spectrometry (ToF-SIMS), in situ scanning electrochemical microscopy (SECM) and atomic force microscope (AFM) to characterize mineral/collector interface, and the flotation technologies for optimizing recovery of valuable minerals. Especially, the recently developing collectors such as Gemini, alkoxyalkylthiourea, dithiourea, amide-hydroxamate and oximido-thiol surfactants, and their specificity to given minerals are evaluated. Based on this crucial review, it is evident that the structural modification approaches for minerophilic or hydrophobic groups, and combined surface analysis approach for further understanding the adsorption mechanism of collectors on mineral surfaces will lay a solid foundation for the future development of flotation collectors. INTRODUCTIONIn mineral processing, flotation is the main process for separation and recovery of valuable minerals from the ores contained them (Fuerstenau et al., 2007). One of the key requirements in flotation process is to increase selectively the surface hydrophobicity of the targeted minerals by collector adsorption so that these mineral particles can preferably attach to air bubbles in a slurry or pulp (Fuerstenau et al., 2007). Flotation collector is a kind of functional surfactant, which is composed of polar and non-polar groups (Somasundaran, & Wang, 2006). Non-polar portion, commonly being linear, branch or ring hydrocarbon group, is termed hydrophobic group. The polar portion, exhibiting strong affinity to mineral surfaces, is known as minerophilic group (Nagaraj, 1988). According to mineral types including saline, oxide and sulfide minerals, flotation collector divides into sulfide and oxide mineral collectors. For efficient recovery of valuable minerals from the refractory complex ores, insights into the adsorption mechanism, hydrophobic model and subsequent flotation approach of flotation collectors have been regarded as an indispensable issue in mineral processing."

Jan 1, 2016

By M. Massinaei, M. R. Yarahmadi, S. Zeidabadi, M. Oliazadeh

"Although the majority of new flotation column installations continue to be for cleaning or recleaning, an increasing number of flotation projects are specifying columns for roughing or scavenging duties. NICICO has recently installed flotation columns operating in rougher, cleaner and re-cleaner circuits at three new copper concentrators; Miduk, Sungun and Sarcheshmeh. Miduk is probably one of the unique operations that use flotation columns in a rougher circuit. The Miduk rougher circuit comprises five CISA parallel columns. The rougher concentrate constitutes 88% of final concentrate and reports to concentrate thickener. The rougher tailings are scavenged with ten 50 m3 mechanical cells. The scavenger concentrate is then reground and cleaned in three 3.2 m columns in parallel. The cleaner tailings are scavenged in six 50 m37mechanical cells. The cleaner tailings along with the rougher scavenger constitute final tailings.In Sarcheshmeh, the cleaner concentrate is re-cleaned in a column. The column tailings are sent back to the cleaning circuit and the concentrate is reported to the concentrate thickener.This paper reviews performance details of the flotation columns utilized in rougher circuits at Miduk and compares their metallurgical performances in an industrial scale with columns at cleaning circuits for copper flotation. Practical limitations for applying the flotation columns in rougher circuits will be discussed in details.INTRODUCTIONThe use of flotation columns has grown rapidly since the first successful commercial application at Mines Gaspe, where columns were used in a cleaning circuit to float molybdenite. Early applications of columns were restricted to replacing or adding final cleaning stages in existing circuits. Columns can achieve superior cleaning as compared to conventional cells due to their ability to support a large froth depth and the use of water for washing froth. Wash water travels down through the froth and crosses the pulp/froth interface, replaces the entrained particles reporting to the froth from pulp and improve the concentrate grade."

Jan 1, 2011

By N. I. Basuki, E. T. C. Spooner

"Abstract - More than 2800 published fluid inclusion data (primary inclusions) from eighteen typical Mississippi Valley-type (MVT) Zn-Pb deposits and districts were examined to study possible relationships between MVT fluid properties and metal tonnages and ore grades. The mean Th and salinity values for fifteen MVT deposits and districts are 122°C ± 21°C and 20.7 ± 2.6 wt% CaCl2 equivalent, respectively. In general, temperatures increase from pre-ore to ore stages, and salinities decrease from ore to post-ore stages. From post-ore to late calcite stages, salinity and temperature decrease with various trends within specific districts.Several conclusions are drawn: first, results show that Hanor’s (1996) salinity threshold for metalrich basinal fluids applies to typical MVT ore fluids (~16 wt% CaCl2 equivalent). Second, the lower limit of mean Th values of measured MVT deposits and districts (n = 15) of ~75°C is similar to Hanor’s (1996) observed temperature threshold for metal-rich basinal brines of ~60°C (n = 224). Third, there is no statistically significant relationship between fluid inclusion homogenization temperatures (Th) and metal tonnages or ore grades. Fourth, there seems to be a tendency for large tonnage districts/deposits to be associated with mean fluid salinities that are relatively low (~16 to 21 wt% CaCl2 equivalent) within the overall range of salinity means (~16 to 26 wt% CaCl2 equivalent). There is also a correlation between higher ore grades and higher salinities. Finally, comparison with other sedimentary rock-hosted Zn-Pb deposit types shows a trend of salinity decrease and temperature increase from MVT, sandstone-hosted and diapir-related Pb-Zn deposits, to vein-type and Irishtype Pb-Zn deposits, and then to sedex deposits. However, more data are needed for sedex deposits. The salinity threshold for significant Zn-Pb transport decreases to =~10 wt% CaCl2 equivalent at ~250°C. This study suggests that fluid inclusion analysis during exploration may be useful in assessing ore-forming potential (threshold salinity) and possible ore grades (salinity)."

Jan 1, 2002

By John W. Vanderwilt

THE fluorescence of scheelite has been an important aid in recent years in the discovery and development of scheelite deposits. The use of fluorescence of synthetic compounds in industry, particularly in advertising, also has expanded greatly during the past decade. As a result, a number of new and convenient units for producing ultraviolet energy have become available, which have led to a greater application of fluorescence in the study of minerals. Studies have shown that the fluorescent color of a mineral may vary: (I) with the kind and quantity of trace elements, and (2) with the particular wave length of ultraviolet energy used. The wave length is dependent first on the type of generating equipment used, and finally on the filter employed to remove the visible light that may be present. A number of so-called ultraviolet lamps are listed and described, together with suitable filters known to be available. Scheelite fluoresces brilliantly with wave lengths of 2200 to about 3000Å., but not with longer wave lengths. The most convenient and efficient sources of ultraviolet for scheelite fluorescence- are portable and laboratory units designed particularly for use with scheelite. So-called ultraviolet light globes of the photo-flood type emit wave lengths too long to cause scheelite to fluoresce. Attention is called to the minerals that fluoresce in a manner similar to scheelite, which necessitates a check test by means of characteristic physical properties. Chemical tests are the final authority both for identity and content of tungsten in scheelite ore.

Jan 1, 1946

By Jan E. Nesset, Julie Fournier, Jorge Torrealba, Colin Hardie

"Gas dispersion studies have been used to benchmark and optimize plant flotation performance for more than a decade, although this technology is not as widely in use as it likely should be based on the significant improvements that have been reported. Part of the reason may be a general lack of awareness within the industry of just what these improvements have been. This paper reviews a number of the reported case studies, groups them into categories of improvement, and draws some general conclusions. The paper will be of interest to plant engineers and technology providers seeking new approaches and tools for improving their own and clients’ processes.INTRODUCTIONThe sector of flotation hydrodynamics that is now known as gas dispersion technology, and the corresponding terminology, had its beginnings in the 1980’s and early 1990’s in the laboratories of McGill University where the students of Prof. J.A. Finch and Dr. C. Gomez conducted studies of gas holdup, superficial gas rate and water recovery on laboratory flotation columns (Laplante et al., 1983; Xu et al., 1991;, Banisi and Finch, 1994; Finch et al., 1999; Nesset, 2011). Sensors were developed for gas holdup (eg), gas rate (Jg) and bubble size (Db) distribution (Tavera et al., 1996: Finch et al., 1999; Dahlke et al., 2001; Chen at al., 2001; Hernandez-Aguilar et al, 2002, 2005). The sensor measurements were rapidly adapted for use in mechanical flotation machines in plant environments (Gomez and Finch, 2002; Gomez et al., 2003; Cooper et al, 2004; Torrealba-Vargas et al, 2004; Nesset et al., 2007). Somewhat parallel developments were being conducted by Gorain and colleagues at the University of Queensland’s JKMRC on pilot and industrial flotation machines using the McGill approach but utilizing alternate sensor designs for eg, Jg and Db (Gorain et al., 1997, 1999; Schwarz and Alexander, 2006) to link flotation kinetics to bubble surface area flux (Sb). Early industrial applications were those led by the university teams from McGill (Canada), the JKMRC (Australia) and the University of Santa Maria (Chile) at plants in North and South America, Australia, South Africa, Asia and Europe. Industrial organizations that brought the technology on-board in the early 2000’s included Teck Resources (then Teck Cominco), COREM, Vale (then Inco), Anglo American Platinum. Several of the major flotation cell manufacturers also purchased the McGill bubble viewer technology for their own equipment studies. The sensors have continued to evolve with multiple and continuous measurement of Jg (Torrealba-Vargas and Finch, 2006, Bartolacci et al., 2008), gas holdup by acoustic means (O’Keefe, 2007) and a combined Jg-Db device called the Anglo Bubble Sizer (Harbort and Schwarz, 2010). A review of the gas dispersion technology use and development have been provided by Gomez and Finch (2002), Harbort and Schwarz (2010) and Nesset (2010)."

Jan 1, 2015

By P Lilly

Blasting is the primary comminution process in most mining operations. This process involves the highly complex and dynamic interaction between two main components. The first is the detonating explosive and the second is the rock mass into which the explosive is loaded. The mechanical properties of the rock material (such as dynamic strength, tensile strength, dynamic modulus and fracture toughness) are important considerations in understanding the blasting process. However, it is the characteristics of the geological defects (joints, foliation planes, bedding planes) within the rock mass that ultimately determine how effectively a blast performs in terms of fragmentation, all else being equal. The defect characteristics include, but are not limited to, their orientation, spacing, and mechanical properties. During the blasting process, some of the geotechnical characteristics of the rock mass are substantially changed. From the blasting outcome point of view, the most notable and important is the change in fragment size distribution that the rock mass undergoes. The pre-blast in situ defect-bounded block size distribution is transformed into the post-blast muckpile fragment size distribution. Consequently, it is fundamental to our understanding of and ability to predict the blasting process that both the blastability of a rock mass and its transformation into the fragment size distribution can be appropriately quantified.

Jan 1, 2001

By John E. Riddell

This review is based on a questionnaire sent out to 24 Canadian exploration companies, known to be active in the mineral exploration field, concerning their practice in the use of applied geochemical techniques in Precambrian terrains. Of the companies questioned, 16 returned completed questionnaires and of these, ten companies stated that they had some experience in this type of work. Of the companies who did not answer or return the questionnaire in time I know that at least three have been quite heavily engaged in applied geochemical work in the glaciated Precambrian areas. I also know that these three companies have been reasonably successful in their ventures, so I feel the following figures and opinions are, if anything, on the pessimistic side. Before continuing with the paper I would like to express my personal thanks to the Chief Geologists, Geologists and Exploration Managers of the various companies who cooperated in making this review possible by answering the questionnaires and making available summaries of their work in the glaciated terrains. Of the companies who stated that they had no experience in geochemical prospecting in glaciated Precambrian areas it is interesting to note that only two have reported that they do not use applied geochemistry at all. Two companies have reported that they make use of applied geochemistry in New Brunswick in areas of-light glaciation. Their opinion is that it is a useful aid to other techniques in evaluating mineralized areas.

Jan 1, 1960

Intensive exploration for iron ore in the banded iron-formations (BIF) of the Pilbara region of Western Australia began in the early sixties and almost immediately established the Hamersley area as a major iron province. The early genetic models for the BIF-hosted ores were based mainly on macroscopic examinations of ores from the "hardcap" zone, and generally accepted a direct relationship with weathering effects on a Mesozoic to Tertiary land surface. Brandt (1964) was the first to suggest a difference in age between the high-grade hematite ores and the more common hematite-goethite types. He initially accepted a supergene origin for both, but later opted for a hydrothermal origin for the hematite ores. Apart from MacLeod (1966), the published views of the next decade reflect a largely parochial interpretation of individual ore bodies, centred mainly on supergene models but with some support for hydrothermal concepts. Except for Ayres (1971), none of the models were backed by detailed mineragraphic data. In 1976, an AMIRA-sponsored CSIRO group began a Province-wide investigation of the wide variety of ore types and BIF, with emphasis on geochemical and textural studies. The resulting conceptual model for a world-wide unified supergene and supergene-metamorphic hypothesis is generally accepted in the Hamersleys.

Jan 1, 1986

The Beaconsfield Gold Mine within the township of Beaconsfield in northern Tasmania has been established in recent years to exploit a known resource in the Tasmania Reef which was mined to a depth of 450 m below surface between 1877 and 1914 yielding 850 000 ounces of gold. Activity at Beaconsfield over the past 30 years has involved drilling to assess the resource and rehabilitation of the top 100 m of the Hart Shaft that had collapsed since the original closure. More recently the mine has been dewatered to the 375 m Level and work is well advanced establishing infrastructure aimed at recommencing production during 1998 - 99. This paper reviews geotechnical studies undertaken to-date and provides a brief overview of some practical methods of analysing ground conditions. It pursues simple observation and analysis as a tool for assessing mine design and ground support options without recourse to extensive monitoring and measurement and avoids the use of elaborate models before the basics are understood.

Jan 1, 1997

By Dight P. M

The challenge of narrow vein mining is to produce ore with as little dilution as possible, at the least cost -commensurate with the increasing degrees of safety being demanded for mine workers by the modem 'duty of care' legislation. Geotechnical factors play an important, if not overriding, role in these areas. The geotechnical factors cover the complex interaction over a period of time, between the in situ and induced rock stresses, rock structures, rock mass strength and the cable, rock bolt and other ground support members. In the Archaean schist belt areas where many of our narrow vein mines occur the pre-mining in situ rock stresses are commonly significantly higher than the overburden stresses. These are concentrated in areas beneath previous open pits and may be highly concentrated in the pillars and abutments of stopes on narrow veins. The presence of high in situ stresses may be suspected from the appearance of drill cores and underground development long before they become sufficiently concentrated by mining to cause damage or bursts. These initial indications are discussed and modem low cost methods of stress measurement are described. Practical and quick methods of analysing the stress redistribution around scopes and other underground excavations are now available and guidelines for interpreting them in terms of rockmass characteristics, stope stability and support requirements are developed with the object of increasing safety, whilst reducing overall costs and dilution.

Jan 1, 1993

By Ho SE, Neil Phillips G, Houstoun SM

There are numerous individual gold deposits in the Archaean greenstone belts of Western Australia, but only 26 have productions and/or quoted reserves in excess of 10 tonnes Au. Most gold production has come from mineralization in shear zones, quartz veins or stockworks in volcanic or intrusive host rocks, particularly tholeiitic basalts or dolerites metamorphosed at sub-amphibolite facies (e.g. Kalgoorlie). Significant prod- uction has also come from BIF-hosted deposits (e.g. Hill 50), and large reserves are quoted for mafic hosts at high metamorphic grade (e.g. Big Bell). Most deposits have marked structural control, great depth extension, and are characterized by zoned alteration haloes of pyritization (with Au), K-metasomatism and carbonation. On the regional scale, most larger volcanic- or intrusive-hosted deposits occur in younger (ca 2.8 b.y.) rift-phase green- stones (Norseman-Wiluna Belt). These belts also have a high prospectivity (36 kg Au/km2 of greenstone belt). Younger (ca 3.0 b.y.) and older (ca 3.5 b.y.) platform-phase green stones of the Murchison and Sodthern Cross Provinces and the east Pilbara, respectively, are progressively less prospective (14 kg Au/km2 and 0.8 kg Au/km2, respectively) and also have progressively smaller deposits. The important regional- and local-scale characteristics of most gold deposits can be explained in terms of a metamorphic- replacement model. In this model, metamorphic H2O-CO2 fluids, focussed by faults and shear zones, infiltrated host rocks and deposit gold at 350 + 50¦C and 1-2 kb, largely in response to fluid-wallrock interaction. In many large deposits, gold precipitation was synchronous with sulphidation of Fe-rich host rocks, but the diversity and abundance of smaller deposits reflects the variety of reactions precipitating gold from ubiquitous, auriferous metamorphic fluids. Regional variations in abundance and size of deposits relate to factors such as tectonic setting, alteration styles and possibly source rocks.

Jan 1, 1986

A number of mineral deposits occur in close proximity to the Pacific plate fronts. Among these deposits are gold-silver and the base metal sulphide deposits of copper, zinc and lead. Gold deposits that commonly occur in these areas are of hydrothermal origin. Of these the epithermal deposits have attracted the attention of the exploration geologists as well as the metallurgists. One vital aspect of the activity of the geologists is the development of models for epithermal gold mineralisation in the Pacific Rim. These models can also be used by metallurgists for predicting gold extraction processes. This paper reviews the mineralogy, fineness and the host minerals of gold and examines the data in the light of gold mineralisation in the southwest Pacific Rim. The gold mineralisation models proposed for the Pacific Rim have been used to predict gold extraction processes suitable for the various mineralisation types. Discussed also are the mineralisation and treatment processes of some selected epithermal gold deposits and gold-rich porphyry copper deposits in Indonesia, Papua New Guinea, Solomon Islands, Fiji and New Zealand.

Jan 1, 1999

By M. Melih Demirkan, Jared Deible, Michael Rosenmeier, Mazen Elias Adib, Juan J. Gutierrez, Raghav Ramanathan

Dewatering and groundwater control is required frequently for construction projects and needs to be accounted for and dealt with care during design and construction to complete the project successfully. Dewatering can cause changes in porewater pressure, which changes the effective vertical stress in a soil mass. Dewatering can also cause changes in groundwater chemistry which in turn can cause changes in porewater pressure and also dissolution of soluble minerals in the soil and rock. The Guideline developed in this study addresses the engineering issues, approaches to lessen the potential risks associated with construction dewatering, and presents dewatering practices to support dewatering applications regulated by the Municipality of Abu Dhabi City (ADM) in the United Arab Emirates (UAE). The subsurface condition within the city presents significant geotechnical problems due to presence of shallow subsurface cavities and soluble minerals in the soil and rock. Therefore it is critical to develop standards for dewatering practices to provide information for local dewatering engineers and contractors with special emphasis to control and to eliminate the subsidence/collapse problems related to dewatering projects within the Abu Dhabi city. The ADM is also responsible for approval of permit applications for projects that involve dewatering. In order to minimize the risk related to subsidence/collapse problems due to dewatering, construction companies and dewatering contractors need to be informed about possible mitigative measures that can be employed to reduce risks. The guidelines were developed as part of this study based on detailed analysis of the local subsurface conditions. A set of rules and regulations are developed for geotechnical and hydrogeological investigations, dewatering design and monitoring criteria depending on the hazard zones, proximity of excavation to critical structures, excavation depth. The Guidelines include examples of permit application packages for three types of dewatering projects; one involving shallow dewatering, one involving intermediate depth dewatering, and one involving deep dewatering. These Guidelines are considered as living document and will be updated as required, as additional information is collected and additional local experience is gained.

Jan 1, 2016

By T. Payne

Underground heat issues are mainly focused on the detrimental effects to a workers health. However, working in hot, humid conditions has other negative effects. Studies have shown that safety, productivity, workforce morale and operating cost are also worsened in these conditions. The human body has several mechanisms for rejecting heat and remaining cool. However, once the air temperature exceeds about 34°C, the only effective mechanism is by evaporation of sweat from the skin. This is assisted by acclimatisation which is the human body?s enhanced ability to combat extended exposure to heat. The body has to remain well hydrated when working in heat as even small degrees of dehydration cause significant decreases in the ability to work in heat. There are two ways in which heat load can be reduced: Through use of refrigeration/vent/cooling to reduce thermal stress on workers; Reduce the contribution that heat sources have to underground heat load (e.g. reduce idle time, fleet size, etc). Some of the sources of underground heat have the potential to be more manageable than others. Geothermal heat and heat from autocompression will be found in all mining situations in varying degrees depending on geothermal gradient and surface temperature, however, the use of equipment and blasting may be streamlined to reduce the underground heat load. It is through a combination of the available options that most mines will successfully control their heat related problems. Mt Isa, which has been a focus for heat related study in Australia, has successfully implemented protocols for working in heat. Through combining these with the installation of a surface bulk air cooling plant, Mt Isa has consistently reduced the incidence of heat illness. This is likely to be the most cost effective method of reducing heat load for deep mines in Australia. Shallower mines which may only occasionally encounter hot conditions should consider more portable cooling options. This study will review the heat issues in underground Australian metalliferous mines.

Jan 1, 2009

By F. Grant

"General *The mining experiences of the coal mining industry in Western Canada have been extremely varied, with the mining companies having to adjust their operations or fail due to the harsh economy of the country in the first part of the century. The bituminous or mountain mines had the railways as main consumers with, at times, optimism that potential steel producers would require metallurgical coal. The prairie and foothills mines mainly provided household fuels, with the fine coal sold to local thermal power plants at discounted prices. In practically all cases fuel competition was very keen, and the less successful mines ceased operations in short-time spans. Knowledge of the parameters that governed the success or failures of the past coal operations should be of value to the present and future mining companies. The initial coal mines were small and were started to supply local demand. These mines had little in the way of capital machinery, engineering, or transportation equipment; therefore the mining methods and mine plans were very simple. The first industrial-sized mines imported most of their management and mining methods from other mining areas, mainly Great Britain. It took time to change the bias of management and mining methods to the requirements of strata characteristics, with rapid closure to those mines that were slow to adapt working methods. The main markets for coal were for household fuel, thermal power plants and railways, with very few other industrial markets developed. The economy of the period was harsh and cyclic and the coal mines were affected more than most industries by these boom and bust periods. It led to the survival of the fittest or the most efficient. Due to the economy, mechanization was introduced to the mines very slowly, with the inability to sell coal fines at a profit being another reason for the delay. Manual labour with hand tools was the main means of production. The work was heavy and arduous, and the pay was based on contract coal tonnage; therefore both men and management paid close attention to details so that nonessential work could be eliminated. Mine openings were dimensioned so that coal could be loaded easily by hand and support requirements were kept to the minimum. Transporting and handling the timber supports required heavy labour; thus the most efficient dimensions were chosen to suit the strata. On the other hand, during the main production seasons the mines tried to make the strata stress work for them so that the pressure was kept on the coal face to keep the coal loose while the strata, a short distance back, was induced to cave to minimize the abutment stresses. This caused mining to be an art, using skills developed by experience with the strata. This led to the development of efficient mine layouts with the openings dimensioned to the strength of the strata and the type of support available. The lack of capital and mechanization, and the manual labour, induced the mines to correlate their service and haulage systems with their mining methods. This caused many innovations that proved very practical."

Jan 1, 1985

There have been many developments in recent years in pipeline transport to enable them to be more widely used in industry. Substantial tonnages of materials that are not affected by water, such as coal and other minerals, aggregates and wastes, can be moved over considerable distances in quite small diameter pipes. Where there are no existing road or rail facilities, long-distance pipelines are usually cheaper to install, and this advantage increases in difficult terrain. Pipeline operators all over the world assert that hydraulic lines pay for themselves in a relatively short time, in spite of the heavy capital outlay, and this is equally true for lines convey-ing slurries or pastes within a plant complex.'This paper reviews some of the more important investigations in the hydraulic transport field. Although reference to systems carrying a wide range of materials is made, the majority of recent published data centres on coal transport.The paper looks at the application to a wide range of particle sizes, the development of non-aqueous slurrying media and coal/water fuels. The review also looks at some of the equipment being proposed to provide more reliable operation and in particular the range of solids-handling pumps now available.-The paper goes on to identify areas where further research and development is required and some of the many organisations undertaking this work.

Jan 1, 1985

By Guy Reed, Russell Frith

In situ or pre-mining horizontal stresses are arguably the least well understood of the principal inputs into underground coal mining geotechnical engineering design, whether analytical, empirical, or numerical. This is a direct result of both the cost and difficulty of obtaining meaningful stress measurements, the various limitations of the measurement method in terms of sourcing strata types that approximate the assumed conditions of the post-measurement mathematics to convert measured strains into stresses, and a common practice by some geotechnical professionals to preferentially utilise generic values rather than interrogate the available measurement data for cause and effect relationships between horizontal stress magnitudes, directions and a range of associated controls. That numerical modelling simulations attempt to mimic reality but often rely on simplified generic horizontal stress input assumptions is a particular cause for further consideratio The paper attempts to further explore the nature of in situ horizontal stresses using a range of stress measurement results from the Australian coal sector supplemented by several international studies addressing the same basic issue, the result being a number of credible and highly relevant “cause and effect" inter-relationships between the three principal in situ stresses in addition to the influence of rock properties (e. Young's Modulus and Poisson's Ratio), cover depth and the larger-scale structural geological environment. In particular, the paper demonstrates that despite being commonly overlooked as a primary rock/coal material property, Poisson's Ratio and the associated K Effect are intrinsic to understanding 3D in situ stress measurement results and therefore, predicting in situ stress magni- tudes more generally for geotechnical analyses purposes. As a fundamental question, the paper addresses whether it is necessary and of engineering value to characterise in situ horizontal stresses: according to distinct "domains," in the same way that more easily identifiable geotechnical properties such as rock mass ratings, coal seam thickness, ply splits, and cover depth are often treated.

Jun 25, 2024

By C. G. Hunkin

In situ, or in-place leaching is concerned with the extraction of metals from natural mineral disseminations without removal from their geologic location which, in many cases, amounts to the reversal of the deposition process accompanied by a presumed increase in velocity of the processes, if the project is to be profitable. Solution mining processes involve removal of minerals such as sulfur, common salt, and potash, generally leaving cavernous voids, in contrast to in situ leaching which term is applied to the selective dissolution of a mineral from its gangue without sensible disturbance of the formation. Where such a process can be operated, the advantages are manifold and have been so recognized by miners from the earliest days of mining. Recent technological developments have encouraged a reassessment of the status of in situ leaching, and it now appears possible to extend the application of the method from a few isolated special situations to many uranium and copper deposits. Anaconda's interest in the techniques stems from long experience with vat and heap leaching, 'dump leaching, and natural leach activities associated with several established mines. Increasing activity through-out the industry has been noted, particularly in leaching low grade pillars and the peripheral zones of operating mines, often by the introduction of leach solutions via boreholes drilled from surface. Reactivation of dormant mines] using similar techniques has been successful. Over the long term, environmental improvement activity will lead to excess sulfuric acid production, even to a disposal problem. The cost of leach solutions and reagents must be reexamined in this light. The mineral industry now classifies as uneconomic deposits of readily soluole minerals whose potential value, on a per acre basis, may De several times that of many currently profitable oil field reser-

Jan 1, 1971