Search Documents

By Susumu Okabe

Injection metallurgy is widely adopted in various fields of metallurgical operations to achieve high productivity. The Mitsubishi Continuous Copper Smelting and Converting Process employs the top blown lance technique for the continuous supply of solid charges and reaction gases into the molten bath, where the agitated bath contributes to enhance the heat and mass transfer and the increased gas/liquid interface area accelerates the reaction. However, excessive splashing of the molten materials accompanied by the injection may cause an unexpected wear of the furnace lining. In order to estimate the splashing rate quantitatively, and to optimize the furnace design and the blowing condition, a physical model study of the top blown gas injection onto the liquid bath was carried out. An equation of the splashing rate was obtained as the function of cavity size, gas velocity and bath properties.

Jan 1, 1995

By Shizhe Liu, Bing Li, Heng Wang, Zuxin Zhao

In this paper, cyclic voltammetry and chronoamperometry have been applied to investigate the effects of Nd2O3 concentration on the anode effects, critical potential for the anode effects and Nd2O3 reduction in LiF-NdF3-Nd2O3 melts at 950℃. The results show that the oxidation peaks in the potential of about 2.7V are attributed to the oxygen ions oxidation and the peak current density increases with Nd2O3 concentration increase from 0 to 0.5wt%. The critical potential caused the anode effects shifts to 0.3V more positive value as Nd2O3 content in the melts decreases from 0.01wt% to 0.5wt%. The cyclic votammograms on W electrodes in the LiF-NdF3-Nd2O3 melts present two pairs of reduction and oxidation peaks, indicating that the reduction of Nd ions in the LiF-NdF3-Nd2O3 melts in two steps rather than one step.

Jan 1, 2014

By M. C. Esposito

Seven pyrite samples purified from coal sources and one ore source pyrite (for comparative purposes) have been characterized by chemical and mineralogical analyses, inherent floatability, apparent specific gravity, surface area, semiconductor type, optical anisotropy, dissolution and oxidation rate. The data clearly demonstrate that pyrites from various coal sources differ not only from ore pyrite but from each other as well.

Jan 1, 1987

By Bo Björkman

A controlled dust generation whereby the dust generated would be enriched with specific metals would considerably facilitate the possibilities of recovering metals from such dusts. A basic understanding of the dust forming mechanisms is of fundamental importance to achieve a controlled dust generation. The present study deals with dust formation in a copper converting process. Dust samples collected from various places in the gas cleaning system were characterised for chemical and mineralogical composition using chemical analysis as well as microprobe analysis. Thermodynamic calculations were used to predict the formation of chemically formed dust at various temperatures and amounts of leakage air to the gas system. The results show that a separation of mechanically formed dust. e.g . Si0:2. Cu and chemically formed dust. e.g .? Ph, Zn, As, Bi. could, to some extent, be obtained due to their different particle sizes. A selective condensation of Pb, Zn and As at various temperatures could. according to thermodynamic calculations, he possible at high temperature. A selective condensation of metals requires an airtight gas cleaning system or a gas cleaning system with a limited amount of leakage air in order to maintain the desired temperature level.

Jan 1, 1996

By Deming Wang, R. A. Overfelt

"The oscillating cup viscometer has become a dominant technique to measure the viscosities of high temperature molten metals. Unfortunately, the viscosity estimation model from the observed logarithmic decrement and period of the oscillation is very complicated. There are still large discrepancies of viscosity estimation values between using different measurement facilities and using different viscosity estimation models for a same molten metal. The purpose of the paper is to evaluate the accuracy of an oscillating cup viscometer in Auburn University. Two well known viscosity estimation models, Roscoe's and Torklep's equations, are compared and discussed. The theoretical literature for the fluid flow inside an oscillating cup is reviewed and a more accurate working equation for the Auburn oscillating cup viscometer is developed. Some design parameters of the oscillating cup viscometer, which directly affect the accuracy of viscosity estimation by using the working equation, are discussed. In addition, applications and experimental measuring data are presented in the paper for several different commercial alloys, such as aluminum alloys: A319, A356 and A201, nickel-base super alloys: In713 and In718, and casting irons, C40 Gray Iron and Ductile Iron.1 IntroductionThe oscillating cup viscometer is the most important and has been most frequently used in viscosity measurement for high temperature liquids [1-4]. The principal advantages of this technique over others are its mechanical simplicity and the ability to measure the time period and amplitude decay with great precision. In the viscometer, a high temperature liquid (such as a molten metal) is contained within a crucible suspended by a wire to form a torsional pendulum, which induces torsional oscillation motion. This motion is damped primarily by viscous dissipation within the viscous liquid inside the cup. The viscosity of the liquid can be calculated by an analytical or numerical solution ofthe equations of motion of the oscillating cup system."

Jan 1, 2001

By Markus Aspiala, Fiseha Tesfaye, Pekka Taskinen

In this paper, the standard thermodynamic properties of Ag3Sb and Ag6Sb intermetallic compounds have been studied by the solid state EMF-method, using Ag+ ion conducting β- alumina and AgI. The intermetallic compounds were synthesized from pure substances in evacuated silica ampoules and their formation were confirmed by the SEM-EDS analyses. The EMF measurements were made on electrochemical cells of the type [Ag | β-alumina | Ag-Sb] and [Ag | AgI | Ag-Sb]. The usage of β-alumina electrolyte, in this study, enabled thermodynamic measurements of the Ag-Sb-intermetallic compounds above 710 K, hitherto unreported. Based on the new experimental data, thermodynamic properties of the Ag-Sb-intermetallic compounds have been determined. The obtained experimental values have been compared with the available literature data.

Jan 1, 2015

By E. J. Peuraniemi

Primary copper production using suspension smelting techniques like Outokumpu Flash Smelting always causes some dust formation. Flue dust particles are formed when sulphide feed material reacts violently with oxygen inducing particle disintegration and total desulphurisation of fragments. In the process, flue dust follows the off-gases to the heat recovery boiler (HRB) where its sulphation takes place because of prevailing conditions. Sulphation releases heat and causes also a drop in particle melting temperature and, further, particle sticking to the walls and heat exchange tube banks. Sulphation of synthetic CU20 particles were examined using a laboratory scale fluid-bed reactor. This study aims to a better understanding of flue dust behaviour in a HRB and, thus, to a better operational practise and design of a HRB. The effect of PSO/PO2 -ratio and temperature on the sulphation kinetics were tested. Standard chemical analysis, light optical and scanning electron microscopy with energy dispersive spectroscopy were used to examine the samples.

Jan 1, 2001

By George S. Dulikravich

An advanced semi-stochastic algorithm for constrained multi-objective optimization has been adapted and combined with experimental testing and verification to determine optimum concentrations of aJ10ying elements in heat-resistant and corrosion-resistant H-Series austenitic stainless steel alloys. The objective was to simultaneously maximize a number of alloy's mechanical properties. This research will result in a rigorous tool for the design of high-strength H-Series steels and other types of alloys unattainable by any means existing at the present time. Such a material-by-design tool will also be able to reduce or minimize the need for the addition of expensive elements such as Cr, Ni, Co, Nb, Ti, V, etc. and still obtain the optimum properties of an aJ1oy.

Jan 1, 2003

By Gervais Soucy, François Quesnel, Pierre Hovington, Wen Zhu, Karim Zaghib, Jocelyn Veilleux

The properties of lithium titanates anodes in Li-ion batteries are highly dependent on their secondary constituents. While their main phase is usually constituted of Li4Ti5O12, significant quantity of lithium titanates compounds of various stoichiometry are often present, due to either the processing, usage or aging of the material. These may go underreported, as many of these spectrums overlap or display low signal in X-ray diffraction (XRD). Samples of nanosized lithium titanates synthetized by inductive plasma were characterized by XRD and scanning electron microscopy (SEM), as they provide a regular yet typical crystallite size and shape including multiple phases. A Rietveld refinement was developed to extract the composition of these samples. Mass balance through further annealing and differential scanning calorimetry (DSC) enthalpy measurements from phase transformations were also used as identification and validation techniques.

Jan 1, 2015

By Toshiki Kabutomori

In fuel cell powered automobiles, hydrogen is required to be stored in materials that have a hydrogen storage density of over 4 mass%; further, these materials should be capable of supplying hydrogen by using the waste heat from a fuel cell, which is at a temperature of 373 K, in order to match the mileage of gasoline-powered vehicles. A Ti-Cr-V alloy, which exhibits a BCC structure and forms a solid solution, is a promising candidate for onboard hydrogen storage materials. Although it has a large hydrogen storage capacity of over 3.9 mass%, the rechargeable hydrogen capacity is limited to approximately 2.6 mass%. In this study, the effects of fine pulverization of the alloy on PCT (hydrogen pressure-composition-isotherm) characteristics were investigated in order to improve the rechargeable hydrogen storage capacity of the alloy. From the PCT measurements of the finely pulverized samples of the alloy, a plateau in the absorption curve was observed to begin at a hydrogen concentration of 0.5 mass%; further, a rechargeable hydrogen storage capacity of 3.3 mass% was obtained. This was greater than that obtained from the sample that was not finely pulverized, i.e., 2.5 mass%. However, the plateau width in the desorption curve was 2.5 mass%, which was the same as that observed for the sample that was not finely pulverized. The increase in the rechargeable hydrogen capacity during absorption is attributed to the precipitation of the -hydride phase (MH~2) directly from the metal phase (phase). The precipitation of the phase (MH~0.5), which should be formed in low hydrogen concentrations, is suppressed as a result of a possible reduction in the internal defects such as dislocations, vacancies, and grain boundaries by fine pulverization and annealing of the alloy.

Jan 1, 2006

By Jing-she Li, Hai-yan Tang, Cheng-song Liu, Wei Liu

"In order to effectively utilize cheap and low quality iron ores, a hematite ore in a certain steel plant in Xinjiang was researched on to obtain ""iron increase and silicon reduction"" by ore dressing operation experiment and the performance indexes of the hematite ore were optimized. Based on the fundamental characteristics and high-temperature properties of the concentrate after ore dressing and other five kinds of iron ores which were co=only used in this steel plant, ore matching principles were proposed and a sintering ore blending optimization model was established. Finally, sinter pot test was carried out to verify the validity and practicability of the sintering ore blending optimization model which was aimed at giving consideration to the sintering indexes and the cost.IntroductionIn recent years, the price of imported iron ore with high quality is always at a high level, while iron ore self-sufficient rate in China is less than 50%. Enormous market demand and high dependence of domestic enterprises on imported iron ore makes the price of it hardly return to rational. In order to get rid of the situation of long-term meager profit and even deficit, more and more iron and steel enterprises in China transit their focus of reducing production cost to the utilization and development of relatively cheap but low-grade iron ore resources at home[l-4l_ However, besides the disadvantages of low iron grade, high content of impurities and complex embedded properties, the high-temperature properties of iron ore often go beyond the suitable ranges for producing sinter with high quality. Thus directly utilization of this kind of iron ore without ore dressing process would probably affect the metallurgical performance and indexes of sinter ore.Previous research and production practice have shown that traditional iron ore matching in sintering mainly focus on the reasonable collocation of properties of iron ores with low quality and high quality, but pay less attention to ore dressing process of low quality iron ores and matching them with high quality iron ores. Actually, compare with directly utilization, iron ores with low quality after ore dressing have higher suitability for matching with high quality ones which is beneficial to reduce the consumption of iron ores with high quality and control the production cost of sintering [5-s1."

Jan 1, 2014

By Anna Wasilkowska

The study concentrates on the effects exerted by microstructure, deformation history and uniaxial stress conditions (temperature, stress state, strain rate) on the mechanical properties offerritic TRIP-aided steels for automotive applications. In low-alloyed TRIP-steels it is quite difficult to separate the effect of the austenite to martensite phase transformation from the influence of the ferritic matrix contributing to the yield stress and uniform elongation. Investigation of transformation kinetics of retained austenite as a function of the deformation temperature show that using the parameter k to characterize the retained austenite stability allows to identify regious of different temperature sensitivity separated by a transition temperature of 10±5°C. The observed low strain-rate sensitivity of the flow stress is an intrinsic property of the ferritix matrix and points to defomtation governed by slip. The ultimate tensile strength is much stronger affected by temperature than the yield stress. The influence of the temperature on the elongation is complex, because of the heating of the specimens by 60-l20°C at moderate and high strain rates. The increase of the total strain can be understood in terms of thermal softening of the ferrite. On the other hand, the steep increase of the stress during dynamic testing is an effect of accommodated elastic and plastic strains in the matrix. The strain- hardening exponent is dependent on the conditions imposed during testing. The martensite transfomtation rate is lower and the critical stress for martensite nucleation is much higher under compression compared to tensile loading. In secondary tensile tests, the yield stress increases steeply, and the ultimate tensile strength and the total elongation depend linearly on the amount of pre-straining. The results confirm that in the range of 8=10-4 s-l the TRIP-effect governs room temperature plasticity. Keywords: TRIP-steels, mechanical properties, strain rate sensitivity, temperature sensitivity, austenite stability

Jan 1, 2003

By Vasil Kopaleishvili

The bainitic Fe-C-Si alloys with optimum content of retained austenite serve as ?containers? for storing of hydrogen. Both the vacancies of fcc lattice and the possibility of forming hydrides of silicon and other alloying elements will be used. The idea is based on our scientific hypothesis. There is the silicon threshold (Si=0,50%) in "Fe-Si" system and Fe-C bainitic alloys, above which it causes self-organized phenomena: sudden increase of hydrogen solubility and amount of retained austenite in the alloy after ??ß transformation, formation of two supersaturated solid solutions <a??r>, "rejuvenation? and its reverse process. Rapprochement of iron atoms when Si=0,50%, causes appearance of new covalent forces where uncompensated electrons of 3d-subshell are involved and it provokes synergetic phenomena. They ?free? silicon atoms from the previous bonds. After that silicon itself becomes a getter of hydrogen using vacancies (14) of 3P2(6)d0(10) subshell and it results in sudden increase of hydrogen solubility in metal. Simultaneously sudden decrease of iron activity takes place. That in its turn ?releases? the carbon. Thus, its redistribution, controlling the bainitic transformation, is hastened. It stipulates for creation of ?brittle bainite" B[a(C,H)+?r(C,H)] after ??ß transformation. While weathering of metal, "rejuvenating", hydrogen diffuses in ?islets? of retained austenite and ?relaxed bainite? (B[(C)+?r(C,H+H)]) is obtained. When heating austenite ?(C,H) is obtained, and after cooling ?brittle bainite? is obtained, etc. Presented scientific hypothesis explains the available experimental facts ("rejuvenation? and its reverse process, graphitization, weldability, forming of flakes, reaching high strength, etc.) in a new manner, as well as, gives real opportunity for creating of new trends in many fields, e.g. iron based HAA. Provisional data having been obtained are encouraging.

Jan 1, 2006

By A. R. G. Azevedo, G. C. Xavier

"The search for technological innovations in the Civil Construction takes as an objective the reduction of costs and increase of the productivity. However, these technologies demand analysis and studies of parameters of control that provide the quality of the products. With the intention of improve the knowledge on industrialized mortars used in mechanized projection machines, a characterization was done in the state anidro, fresh and hardening of three mortars, being each one of a State, Rio de Janeiro, Sao Paulo and Bahia. The tenors of water/ mortar was obtained through tests done in built environment, it varied from 0,17 to 0,26. From these results, the mortars were projected by his respective consistency, analyzing its compressive strength, and traction adherence resistance, in this way, the good performance of the revetments was provided.IntroductionThe market competitiveness of Construction has led companies to invest in construction processes and techniques in order to rationalize and optimize the buildings. Thus, changes emerged in coating system providing improvements in conventional materials and novel construction techniques, such as mortar industrialized and mechanized projection.Adopting projection equipment mortar is flagged as one of the solutions to reduce the interference of hand labor in construction, optimizing the performance of internal and external coatings, as well as streamline the production process and transportation, reducing lossesMaterials and deadline for execution of the casing(l)The process has been used due to its benefits, however, studies are necessary parameters for quality control of these mortars used in the projection to greater knowledge of mixing and market acceptance. It is therefore quite relevant information processing techniques available on the subject, as necessary to carry out research aiming at defining specific indicators of quality."

Jan 1, 2013

By Yuanpei LAN, Minren XU, Deliang NIU, Zhu WANG, Qingcai Liu, Shan Ren

Removal of gas is the major function of RH degasser. To optimize the RH refining craft in Chongqing Iron and Steel Co. Ltd, the degassing effect of RH degasser at different degrees of vacuum was investigated using a vacuum induction furnace. In addition, the effect of processing time on the gas content dissolved in molten steel was also studied. The results showed that degree of vacuum was one of the important factors that determined the degassing efficiency in RH refining process. High vacuum degree is helpful in the removal of gas, especially in the removal of [H] dissolved in molten steel. The processing time could be reduced from 25-30 min to 15 minutes and gas content could also meet the demand of RH refining

Jan 1, 2015

By Seetharama C. Deevi, Mohammad R. Hajaligol, Sarojini Deevi

"Carbides and nitrides of iron are being considered as magnetic materials for high-density recording due to their chemical stability and high-saturation magnetization values (> 100 emu/g). Iron carbides and iron nitrides with magnetic properties suitable for magnetic media were synthesized by employing a novel synthesis procedure based on fluidization of powders in reactive atmospheres. Fluidized-bed reactors of laboratory, bench, and pilot scale were employed for the synthesis of iron carbide, FeSC2, by reducing and carburizing U-Fe203 in the temperature range of 300 to 550 ºC. A temperature of 400· ºC and a reaction time of 2 to 3 h are found to be optimal for the synthesis of iron carbide. When the carburization was carried out in a reducing and carburizing atmosphere such as carbon monoxide, nucleation and growth of FeSC2 occurred directly from Fe304 with no intermediate phases such as FeO or Fe. Longer carburization times resulted in the deposition of carbon on the surfaces of FeSC2 particles due to Boudouard reaction, and higher temperatures favored the formation of a mixture of carbides such as FesC2 and Fe3C. Iron nitrides were synthesized by reducing u-Fe203 in the temperature range of 350 to 550 ºC, followed by nitriding in the temperature range of 350 to 550·ºC. The powders were characterized using X-ray diffraction, scanning electron microscopy, thermogravimetric analyzer, and a vibrating sample magnetometer.IntroductionRecent demand for high-quality recording of optical, electrical, and audio signals generated interest in magnetic tapes with high-recording densities as compared to the conventional magnetic tapes based on U-Fe203. At present, commercially available magnetic tapes contain maghematite, U-Fe203, as a magnetic material with a saturation magnetization of90 emu/g and a coercive force of 400 Oe. Recording of signals at a higher density per unit volume of magnetic material demands magnetic materials with high-saturation magnetization and a reasonable coercive force. Although metallic iron particles possess a saturation magnetization of 130 to 150 emu/g and a high coercive force of 1000 Oe, the gradual oxidation of iron-to-iron oxides (of lower saturation magnetization) prevents the use of iron particles for high-density recording. In contrast, iron carbides such as FesC2, Fe7C3 and iron nitrides such as Fe4N and Fe3N possess excellent magnetic properties coupled with good electrical conductivities and high hardness. The carbides and nitrides of iron have generated significant interest as magnetic materials for the next generation of magnetic tapes due to their unique magnetic properties and relatively greater oxidation resistance as compared to metallic iron particles [1-4]."

Jan 1, 1994

By Vladimir Panjkovic, Ostrovski. Oieg, Campbell Cripps Clark, John Truelove

"Effects of properties of raw materials and blast on the performance of an iron bath reactor have been examined by a mathematical model. The model consists of three modules: 1) chemical reactions in the gas phase and heat transfer from gas to droplets ejected from the bath; 2) heat losses from the vessel and radiative heat transfer from the freeboard to the bath; and 3) heat and mass balances for the bath. The following parameters of the process are calculated: coal, ore, flux and oxygen consumption, post-combustion ratio and heat-transfer efficiency, temperature and composition of the off-gas, and slag and metal chemistry.IntroductionOne of the anticipated advantages of smelting reduction over conventional ironmaking is the use of lower-grade raw materials. In this work, the effect of-properties of raw materials on the performance of an iron-bath reactor is examined with a numerical model. The model is also used to assess the effect of properties of the blast (flowrate, temperature and oxygen enrichment) and ejected droplets (generation rate, size and ratio of total weights of slag and iron droplets) on the key parameters of the process. In the process coal, oxygen, ore (which may be partly prereduced) and fluxes for specified slag composition are charged to the bath. Slag and iron droplets are ejected from the bath into the gas phase, where they are heated before returning to the bath. Iron droplets undergo decarburisation and reoxidation with CO2 and H2O. Dust is also generated from the bath, and oxygen or preheated air for post combustion is injected from the top of the vessel.The model consists of three modules: 1) reactions in the gas phase and heat transfer from gas to droplets ejected from the bath; 2) heat losses from the vessel and radiative heat transfer from the freeboard to the bath; and 3) heat and mass balances for the bath. The structure of the model and the data exchange between the modules are shown in Fig. 1. The following parameters of the process are calculated: coal, ore, flux and oxygen consumption, postcombustion ratio (PCR), heat transfer efficiency (HTE), off-gas temperature and composition, slag and metal chemistry, and rates of decarburisation and reoxidation of the iron droplets."

Jan 1, 1996

By Shuqiang Guo, Xionggang Lu, Yuyang Bian, Weizhong Ding, Lan Jiang, Kai Tang, Changyuan Lu

For recovery of rare earth elements from the NdFeB based permanent magnet scraps, a high temperature process was used. Permanent magnets scraps were firstly oxidized in air. The optimal oxidation conditions under air are at temperature of 700oC holding for 30min. After the oxidation process, the oxides were reduced by graphite crucible at 1500oC under Ar atmosphere. By this way, the rare earth elements were recovered in the form of oxides, and Fe was separated to the metal phase. Boron distributed in both the rare earth oxides (REO) containing slag and the metal phase. In order to reduce the boron contents in the rare earth oxides, the carbon saturated iron bath and NdFeB added carbon saturated iron bath were used to refine the slag. By this process, the rare earth oxides with a comparatively high purity of 98.2% were gotten.

Jan 1, 2015

By Richard D. Hagni

Process mineralogy has not been given adequate attention in years past, because geologists have not been sufficiently interested in applying mineralogical techniques to industrial processes, and most process engineers are not adequately trained to use them. Although some individuals and institutions have made efforts to improve the situation, it is only in the last few years that the significance of applying the methods of mineralogy to a wide variety of industrial processes has been fully appreciated. Presently, the formation and organization of several groups devoted to applied mineralogy have created a more amenable climate for the development of process mineralogy. As a result, the presentation, discussion, and publication of the results and case histories of process mineralogy have become fairly common. Short courses affording hands-on experience with applied techniques are now available to the many geologists and process engineers engaged in industrial mineralogical processes. The future role of the process mineralogist is viewed as an expanded one, which will increase in value.

Jan 1, 1982

By P. Maraboutis

Iron removal by precipitation as jarosite from Fe-Ni-Co sulfate solutions, (synthetic or real, resulting from laterites leaching) has been investigated. Precipitation was carried out at 95 C, and at an initial pH 1.6, which was either kept constant with CaCO3 or Li2CO3 additions, or left to drift with the evolution of the reaction to lower values. The precipitation of K-, NH4- and Na- jarosite was initially examined using synthetic solutions. In all cases, hydronium ions were incorporated into the precipitate as well. Residual iron in solution was lower (0.2-1 g/1) and equilibrium was achieved faster (within 4-8 h) when precipitating K¬jarosite at constant pH, using CaCO3 for neutralization. Nickel and cobalt losses were small. Na- jarosite precipitation was also studied from real solutions with high initial iron content, under constant pH=1.5, controlled with CaCO3 additions, and it was shown that low residual iron concentration in solution (0.3-0.5 g/1) can be achieved again, with relatively small nickel and cobalt losses. The thickening and filtration characteristics of the precipitates were excellent in all cases examined.

Jan 1, 1988