Search Documents

By Sepp Härkki

The energy crisis in Finland after World War I1 together with a sharp rise in the price of energy caused Outokumpu Oy to consider replacing the electric furnace smelting of copper concentrates by some other method. The flash smelting method developed under these circumstances offered a considerable saving of fuel through the utilization of the reaction heat of sulphides and yielded a high recovery of sulphur in the form of acid. The pilot plant testing of the new process was carried out in the years 1947 - 1948. The process was adopted for the smelting of copper concentrates (1) (2) (3) on a commercial scale in 1949 and applied successfullv to the smelting of -nickel concentrates' at the Harjavalta Works in 1959 (4) (5) (6). In 1962 Outokumpu adopted another type of flash smelting where elemental sulphur is recovered from the gases after the thermal decomposition of pyrite in the flash smelting furnace (7) (8): In recent years, the copper-nickel flash smelter and pyrite process have been combined to produce elemental sulphur instead of SO2 from the smelter gases (9) (10). The basic idea of the Outokumpu flash smelting process for sulphidic ores is that the conventional methods with separate roasting and smelting operations are replaced by a combined roasting, smelting and part-converting process carried out in one unit. The heat generated from the exothermic reactions can thus be used for smelting the ore so that only a small amount of additional fuel is needed. The characteristic of the method is also that the dried, fine-grained concentrate is smelted in suspension, which offers the best conditions for rapid reactions. The recovery of waste heat from the furnace off-gases had been considered already in the original flash smelting system. A

Jan 1, 1976

By E. J. Peuraniemi

Recently commissioned Kennecott-Outokumpu flash converting was developed to replace the approved but environmentally outdated Peirce-Smith -converting to satisfy the globally tightening emission regulations. In the present study, dust formation and reaction mechanisms of two copper mattes with different experimental parameters were studied in lean suspension conditions. Both mattes had very high copper content of approximately 75 wt% and low iron content of 4.5 wt% and 1.2 wt% Fe. A laboratory scale, vertical laminar-flow furnace with a low feeding rate was used to simulate the phenomena taking place in the reaction shaft of a flash converter. Experimental conditions included temperature of 1300 °C with reaction gas oxygen contents of 20 vol%, 50 vol%, and 75 vol%. In the experiments, sieved particle fractions were fed to the furnace and sampled after short reaction time intervals by quenching them into a water film. Collected particles were analysed chemically for their main elements to define their removal rates. Also, optical and scanning electron microscopy with EDS-analyser were applied to determine phenomena occurring during reactions. Kinetics of oxidation as well as ignition of particles are discussed. Changes in particle morphology, size, and composition are reviewed to describe dust formation and reaction mechanisms.

Jan 1, 1999

By Derek J. Fray

"In order to extend the application of fused salts in\the electrowinning and electrorefining of metals, it is necessary to maximise the current density, minimise the voltage drop and greatly increase the area of electrode surface so as to compete with the space-time yield of pyrometallurgical reactions. The various designs of electrowinning cell are reviewed and it is shown that by the application of a modest centrifugal field it is possible to reduce the anode to cathode interelectrode spacing to 4 mm whilst still maintaining a current efficiency of 85-90%.The thermodynamic potential for electrorefining is far less than for electrowinning yet fused salt electrorefining is only applied in limited cases. The reasons for this are discussed and the important design parameters evaluated. It is concluded that by using packed bed electrodes, separated by a diaphragm, the possibility of electrorefining with very low energy consumption can be achieved. Carbothermically-produced metals are always cheaper than those produced by electrolysis but suffer from the disadvantage of low purity. It is proposed that fused salt electrorefining may offer an energy efficient way of upgrading the metal. IntroductionThe majority of metals can be deposited from fused salts (1,2) but as commercial production is restricted to the more reactive elements, it is worthwhile considering the advantages and disadvantages of fused salt electrolysis as' compared to smelting and aqueous electrolysis. The advantages over aqueous extraction are as follows:1) the much higher conductivities and diffusivities result in much lower IR losses and higher current densities can be achieved at modest voltages;2) the elevated temperatures of operation result in larger exchange currents which give rapid kinetics and lower activation polarisation for the electrode reactions;3) the absence of water as a solvent means that it is not necessary to consider the evolution of hydrogen as a competing cathodic reaction. Furthermore, alkali halide salts, often used as solvents in fused salt electrolytes, have high deposition potentials;4) molten salts generally are mutually soluble and, therefore, concentration polarisation effects are minimised."

Jan 1, 1988

By Jiangtao Li, Zhongwei Zhao, Xingyu Chen, Xuheng Liu

In tungsten ion-exchange process, excessive sodium impurity enters into ammonium tungstate solution. However, the Na content of the final ammonium paratungstate (APT) product must be strictly controlled. Consequently, it is necessary to remove Na from the ammonium tungstate solution during processing in order to obtain the required purity of APT. In this study, porous Na specific absorbent, Na1+xAlxTi2−x(PO4)3, is used to remove Na from the ammonium tungstate solution. Through experiments, the effect of reagent concentration of Na1+xAlxTi2−x(PO4)3, reaction time, reaction temperature and Na concentration on the Na removal were investigated. The results showed that under optimal reaction conditions of reagent amount of NATP 1.0 times of theoretical amount, reaction temperature 25 °C and reaction time 15 min, the Na removal from commercial (NH4)2WO4 solution can reach 98%. Na1+xAlxTi2−x(PO4)3 has a good applicability to different Na+ concentrations. The obtained APT product reaches the national standard purity of zero level.

Jan 1, 2014

By Jonkion M. Font

An expression for the distribution ratio of arsenic between slag and copper matte or liquid copper was developed by both, an extension of the Reddy-Blander moderl for deriving a priori the arsenic capacity, and by a relationship between the arsenic capacity and the arsenic distribution ratio. In this study, the a priori arsenic capacities in the FeO-SiO2, CaO-SiO2,MgO-SiO2, FeO-CaO-SiO2, FeO1.5-CuO0.5-MgO-SiO2, FeO-FeO1.5-CuO0.5-CaO-Mgo and FeO-FeO1.5-CuO0.5-CaO-Mgo-SiO2, slags were calculated at 1573 K. The a priori arsenic distribution ratio between the FeO-FeO1.5-CuO0.5-CaO-MgO-SiO2 slag and copper matte mn (Lx, )' and between the FeO-FeO1.5-SiO2 or FeO-FeO1.5-CuO0.5*-CaO-Mgo slag and liquid copper (Ls/cua) were calculated. The model calculated data are found to be in good agreement with the reported experimental data. The availability of reliable thermodynamic data for slag components and impurities in the slag-matte- metal system is essential for the accurate prediction of impurity capacities and distribution ratio data. The arsenic distribution ratio model developed here, can be extended for predication in multi-componet slags and mattes or liquid metal, and thereby may lead to the development of new slag systems for the efficient removal of arsenic in the copper smelting, converting and refining processes,

Jan 1, 2003

By Shenghui Guo, Jianbo Lan, Hongying Xia, Jinhui Peng, Lihua Zhang, Libo Zhang

Spent Hawaii nut shell was converted into a high-quality activated carbon via steam physical activation. Analysis of the experiment including activation temperature, activation duration, steam flow rate on the adsorption capability and yield of activated carbon were identified. Response surface methodology showed that the activation temperature was identified as 866 , an activation duration of 36 min and a steam flow rate of 2.5mL/min with the methylene blue adsorption number of 195 mg/g and yield of 77.75%. The key parameters that characterize quality of the activated carbon such as the BET surface area, total pore volume and average pore diameter were estimated to be 1125m2 /g, 0.94mL/g and 5.21 nm, respectively. Additionally, by the SEM analyses of char and activated carbon, the surface of activated carbon has large number of pores of irregular and heterogeneous morphology.

Jan 1, 2016

By A. W. Worcester

The plant is designed to produce 60,000+ tons of refined lead per year from a nominal feed consisting of 110,000 tons of SLI and industrial batteries, and 10,000 tons of lead contained in drosses and scrap. The plant will also produce as by-products polypropylene chips and detergent grade sodium sulfate, using the Engitec Impianti CX Technology. The battery separation circuit will consist of a battery breaking hammermill and a vibrating screen with water sprays to separate the battery paste from the grid metal and other battery components. The battery components, consisting of ebonite, and separator materials, will be separated' from the grid metal and classified with the use of hydrodynamic water separators. The battery paste will be treated with sodium carbonate to produce a lead carbonate paste for smelting in a reverberatory furnace. The slag from the reverberatory furnace will be campaigned through a traditional primary blast furnace to produce hard lead. The sodium sulfate liquor from the lead carbonate filtration step will be crystallized to produce anhydrous sodium sulfate. The metallic grid metal will be treated through a small rotary smelter of the Engitec design to produce a hard antimonial lead. The plant's scheduled to be commissioned 12 months after receipt of all of the Federal and state permits. The plant will be integrated into the Buick Primary Lead Smelter, located in the center of Missouri's New Lead Belt, at Boss, Missouri. This will allow The Doe Run company to fully utilize all of its existing assets.

Jan 1, 1990

By J. Wendt, P. R. Sahm, T. Uloth, M. Weck, F. Foertsch

"The FEM program systems CASTS (Computer Aided Solidification TechnologieS) (1) and FINELF (FINite ELement Frontal Solver) are used to optimize a thin walled die casting. After a short description of the programs it will be worked out how to use them not only for simulating solidification processes but also for optimizing the design of workpieces. The calculations will be done for an automobile's support bracket which is manufactured in a well known car factory in Stuttgart, FRG.IntroductionAt the Aachen Foundry Institute the software package CASTS was developped to simulate solidification of castings. In order to optimize the whole manufacturing process it does not appear sufficient any more to take into account only the specific aspects of casting. For instance one has to consider additionally the stress situation under service load. For this reason the Foundry Institute together with the Aachen WZL-Institute (Machine Tool Laboratory) and the car factory mentioned above started to probe into a first step in that direction. Figure 1 shows the support bracket which shall be optimized."

Jan 1, 1986

By D. E. Larson

The U. S. Bureau of Mines has developed a image analysis methodology to correlate the energy consumed during the grinding of an ore to the mineral liberation achieved. Energy consumption values are obtained using a laboratory-scale ball mill equipped with a torque sensor, and an automated image analyzer is used to determine the liberation present in ground products. By combining liberation information with energy consumption data an appraisal can be made of the energy required to liberate the mineral(s) of interest. Results of tests performed on a complex sulfide material determined the effects of grind duration on the liberation achieved and the energy efficiency.

Jan 1, 1995

By W. L. Dalmijn

The processing of scrap and scrap cars starts with size reduction by a hammermill, or shredder. After the liberation the magnetic fraction is removed. The remaining non¬magnetic fraction mixed with other materials is screened and each fraction is processed separately. The increased use of plastic has a negative effect on the recovery of metals and waste production. At Huron Valley, Belleville Michigen, USA, the non-ferrous fraction from 5 million obsolete cars per year, containing 200,000 tons of non-ferrous metal, is processed. Aluminium Is recovered with a heavy medium separation process and concentrated with eddy current separators. The remaining heavy non-ferrous fraction is concentrated by a new combination of eddy current separation and image processing. After this separation process the zinc fraction is melted and refined and the copper, brass, stainless steel and other high-quality concentrates are sold to the secondary industries. The recycling of car scrap has become an important source of metals and materials for the secondary. materials processing industry.

Jan 1, 1995

By R. G. Reddy

Reduction of different chromite ores with carbon was studied as a function of C/FeO ratio and temperature in the range 700 °C to 1100 °C by thermogravimetry (TGA) analysis. Powders of chromite ore(-150 mesh) and carbon(-150 mesh) were thoroughly mixed in a desired proportions and were placed in the reaction crucible. The reduction rates of reactions were determined by continuously monitoring the weight loss as a function of time at constant temperature using TGA set up. The analysis of results suggest that FeO present in the chromite ores is reduced to Fe involving gaseous intermediates CO and CO2. The overall rate of FeO reduction is controlled by the oxidation of carbon. A kinetic equation, that of random nucleation, was proposed. The activation energies for the reduction of FeO, present in Roast Movat and Transvaal ores, with carbon were determined to be 55800 and 23000 J/mole, respectively. The results of the present study are compared with the data available in literature. The low activation energy values as determined in this study suggest that the carbon oxidation reaction is catalyzed. It is concluded from the present investigation that the low grade chromite ores can be significantly upgraded to higher value added chromite that can be used as a feed source for economical smelting.

Jan 1, 1998

By Masao Miyake, Eiichiro Matsubara, Tetsuji Hirato, Yasuhiro Awakura

"Zn-Cr alloy coating with around 15 wt% Cr has been found to have much higher chemical corrosion-resistance to steel than conventional zinc plating, while· its structure has not been clarified. The Zn-Cr alloy plating is performed at high current densities around 1 A cm-2 and for 10 to 20 sec using acidic aqueous sulfate solutions with some additives in the iron-steel industry. Due to the high current densities, it seems reasonable to consider that the Zn-Cr alloy plating proceeds under an unsteady-state condition and that the resulting coatings have a non-equilibrium phase and have a structure change in the .direction of thickness. In this research, the crystal structure of the Zn-Cr alloy coating electrodeposited at high current densities and change of the structure in the direction of thickness were examined by X-ray diffraction. The coatings containing under 20 and 35-40 wt% Cr had hcp and bee structure, respectively, while the coatings containing 20-35 wt% Cr comprised two phases with the hcp and the bee structure. The structure of the coating varied in the direction of thickness; both the hcp and bcc phases coexisted in the vicinity of the substrate, while the hcp phase became predominant with increasing distance from the substrate.IntroductionRecently it has been reported that Zn-Cr alloy coating containing around 15 wt% Cr has much higher corrosion-resistance to steel than conventional zinc plating.1-3) The corrosion-resistanc·e of Zn-Cr alloy plated steel sheet with a plating amount of 20 g m·2 is, for example, superior to that of Zn plated steel with a plating amount in the range 60 to 90 g m·2 , which is widely used for automotive bodies today.4l The Zn-Cr alloy plating is obtained by electrodeposition at current densities over 0.5 A cm·2 from a sulfate solution containing zinc and trivalent chromium ions and some additives.5•6) The deposition current densities mentioned above are much higher than those for usual electroplating processes, e.g., Zn, Cu and Ni plating, carried out about 0.05 A cm·2 • Therefore, the time required for plating is very short; around 10-20 sec. Due to the high current densities, it seems reasonable to consider that the· Zn-Cr alloy plating proceeds under an unsteady-state condition and that the resulting coatings do not have a phase expected from equilibrium diagrams; no phase diagram of the Zn-Cr system with a full composition range has been available. 7). In other words, the alloy phase plated would be a non-equilibrium phase with unknown structures."

Jan 1, 2000

By Sven Reutzel

Investigations show that Co-based melts embedded by glass flux in a crucible can be under- cooled nearly as strong as samples processed containerlessly by electromagnetic levitation. This allows to measure magnetic susceptibility on undercooled melts while combining the use of a Faraday-balance and undercooling technique. The magnetic susceptibility of Co and Co-based alloys (such as Co-Pd and Co-Cu) is investigated as a function of temperature from superheated to undercooled state. This is done by measuring the change of magnetic force F, on a sample in a constant magnetic field Bo and an additional gradient field by means of a Faraday-balance. When liquid Co-based alloys are undercooled the magnetisation steeply rises if temperature approaches the Curie temperature. The magnetisation is measured for some Co-based alloys in liquid state as a function of alloy system and its concentration. The results show that the magnetic susceptibility of the liquid undercooled samples follows a Curie-Weiss behaviour, from which Curie temperature and magnetic moments for the liquid state are inferred.

Jan 1, 2002

By P. J. Mackey

New and emerging, as well as proven technologies for the smelting of copper, nickel, lead and zinc are briefly reviewed. The number of new technologies available today is greater than at any time in the past, and interest and development activities remain high despite the economic dif-ficulties faced by the non-ferrous metallurgical industry. Part of the impetus is provided by the realization that only the most cost effective producers will remain competitive, and that new technology is one key to cost effectiveness. The commercially proven "new" copper smelting processes can now be considered to be conventional- technology, and are expected to dominate copper smelting for acme time. There is a growing. interest in continuous copper converting, although direct smelting and converting to copper in one vessel remains the- ideal. There is little activity in nickel smelting. After many years. of development, it appears that several new direct lead smelting processes will soon be a commercial reality. The electrolytic zinc process is expected to continue its dominance, although there is a renewed interest in pyrometallurgical approaches. One of the new zinc processes, and a molybdenum smelting process, illustrate the possibilities of using plasma technology in non-ferrous metallurgy. In the area of complex sulphides, there is perhaps less interest in the treatment of bulk con¬centrate, and more in the treatment of so-called dirty copper concentrates. Much of the technology ancillary to smelting has remained relatively unchanged, and more effort must be made to advance the technology in areas such as materials handling, gas cleaning and sulphur fixation, and energy recovery. More attention to engineering design is also needed. Escalating capital costs may make mini-smelters attractive, but imaginative technology and innovative engineering will be required to make them cost effective. Finally, a glimpse is offered of the smelter of the future.

Jan 1, 1983

By E. A. Werner, W. Liebfahrt, J. Blaha

"The influence of the composition and the microstructure on the plane strain fracture toughness of five cold work tool steels all processed via the powder metallurgical route is investigated using 3-point bending specimens. The steels differ in composition and therefore possess different volume fractions of carbides. The amount, size and distribution of the carbides in the matrix are estimated by quantitative image analysis on a plane parallel to the fracture surface without discrimination of the carbide type, since the carbides are always much harder [1,2] than the matrix, irrespective of their composition. Due to the production of the steels via the powder metallurgical route almost all carbides are spherical in shape. The mechanical in-situ properties of the matrix are characterized by indentation tests performed with an ""UltraMicro"" -indenter in a scanning electron microscope.IntroductionCold work tool steels are used as tools in applications where excellent wear resistance and high hardness are required. Examples are cutting, woodworking, thread rolling, wire and deep drawing, cold extrusion and pressing of parts at process temperatures below 200°C. For such applications the steels must show an optimum combination of hardness, wear resistance and toughness while offering good machinability. Hardness and wear resistance are controlled by the amount of carbon and carbide forming elements such as molybdenum, tungsten, vanadium, chromium and niobium. These elements are present in the MC-, M6C and M7C3-carbides and are also responsible for the precepitation of secondary carbides during tempering. In this report attention is paid to the influence of the primary carbides only, while the very small ~~nm) secondary carbides will be treated as constituent of the homogeneous matrix. Increasing the amount of carbides (alloying elements) usually results in a decrease of the material's toughness which is caused by the presence of clusters and/or bands of carbides. To achieve an optimum combination of hardness, wear resistance and toughness many of the today's cold work tool steels are processed via the powder metallurgical (PM) route, which helps to prevent non-uniform element/carbide distribution because of the rapid solidification of the powders used. The resulting microstructure of the tool steel then consists of a tough matrix with uniformly distributed hard carbides· of globular shape. This shape of the carbides is also desirable instead of blocky carbides present in non-PM tool steels, since they improve the machinability of the steel. An additional advantage of PM-steels lies in the possibility to produce near net shaped tools thus lowering the costs of machining."

Jan 1, 2000

By Józef Czemecki

Polish copper concentrates are characterized by high levels of impurities, particularly Pb and As. Two technologies are being used for copper concentrate smelting at KGHM Polska Meidz S.A., namely the shaft furnace process (Legnica Copper Smelter, Glogów I Copper Smelter) and a single-stage process for direct to blister concentrate smelting in a flash furnace (Glogów II Copper Smelter). Both technologies are used at different physical and chemical conditions which results, in different impurities behavior. The paper presents flow sheets for copper production in a plant using the shaft furnace process and in another in which a single stage flash process is used. The metals distribution in particular semi-products is given as well as a method for elimination of impurities from the copper production cycle. Methods are also discussed for alloy and matte converting and copper refining to obtain low Pb and As concentrations in anode copper (0.3% Pb and 1500 ppm As maximum) that are being used in the KGHM Polska Meidz plants. Useful co-operation between the plants using different technologies, aimed at the limiting the effect of undesired impurities on the quality of blister copper produced, is also described.

Jan 1, 1998

By R. Schaller, Ch. Karcher, A. Thess

"Electron beam evaporation of liquid metals is an innovative technology increasingly used in industry to produce very thin coatings of high purity. In this process the surface of a metal ingot, placed in a water-cooled copper crucible, is heated by bombarding it with a high-energy electron beam gun. The material melts, forming a free surface and eventually starting to evaporate. The rising vapor cloud condensates as a thin film on a moving substrate. The strong energy input at the free surface gives rise to vigorous thermos capillary and buoyancy driven convective motion within the melt, leading to unwelcome heat losses. This paper aims to show how these losses can be reduced by optimizing the geometry of the crucible and by using external magnetic fields. We present both experimental and numerical results.IntroductionElectron beam evaporation of liquid metals [l] is an innovative PVD-technology which is excellently suited for the industrial production of high-quality coatings. In this vacuum process a high-energy electron beam heats up the surface of a metal ingot. The ingot melts and forms a free surface. A schematic view of the arrangement is shown in Figure 1. When the temperature of the free surface exceeds the actual (pressure-dependent) saturation temperature of the ambient gas, the liquid starts to vaporize. The rising vapor cloud finally condensates on a moving substrate located at some distance above. To guarantee a superior quality of the coating the melt is typically confined in a water-cooled copper crucible. The intensive cooling is necessary to avoid chemical reactions between the melt and the crucible walls, that is, crucible materials and their reaction products are practically excluded from evaporation."

Jan 1, 1999

By B. L. Chulu

In the carbothermic reduction of lead sulfate to produce lead, the inclusion of soda ash (Na,CO,) in the charge provides for the control of sulfur dioxide in the effluent gas. An important mechanism in the process appears to be the carbothermic reduction of the sodium carbonate whereby sodium gas and carbon monoxide are produced. These intermediates then participate in the reduction of the lead sulfate to produce lead metal and stable sulfur species in the molten slag phase. In addition, there is some evidence that the presence of lead metal in the charge may also serve to increase the lead recovery in the process. These aspects were investigated by conducting laboratory-scale smelting tests with small charges (;3g), at 1173°K(9000C). Recovery did not exceed 74w% and the role of incipient lead metal in the charge could not be clearly assessed.

Jan 1, 1993

By A. Kontopoulos

The extraction of nickel and cobalt from low-grade greek laterites by sulfuric acid leaching has been studied. Batch and continuous mini-plant atmospheric leaching as well as pressure leaching techniques were employed. Atmospheric leaching at temperatures as high as 95 OC generally resulted in low Ni extractions (up to 82%), high acid consumption (650-850 kg/t ore or 80-100 kg/kg Ni) and high Fe co-dissolution (30%). Pressure leaching at 260 OC increased Ni extraction to over 98%, with minimal Fe co-dissolution (2.5%); acid consumption was 300 kg/t ore (31 kg/kg Ni). Detailed experimental results and conceptual flow sheets for atmospheric and pressure leaching are presented.

Jan 1, 1991

By Oluwatosin A. Aladejebi, Apsara S. Jayasekara, Raymond J. Longbottom, Mark Reid, Marc in het Panhuis, Brian J. Monaghan

The coke analogue is a new research tool that has been developed to quantify and characterize the effect minerals in coke have on coke reactivity. The analogue material is made from a number of different carbon or carbon containing materials and minerals to in part replicate real industrial coke’s reactivity behavior. Elucidation of the effects of minerals on coke reactivity has proved difficult due to the complex and heterogeneous nature of industrial coke and the potential non-additive effects of minerals on coke reactivity. The coke analogue addresses this complexity and heterogeneity through control of its mineralogy, mineral size and mineral dispersion through the analogue, porosity and carbon structures. Initial studies using the analogue were focused on coke dissolution kinetics in liquid iron but recent work has focused in characterization of its porosity, carbon structure and rate of reaction.

Jan 1, 2014