Search Documents

By Osarnu Inoue

In Mitsubishi Continuous Copper Smelting and Converting Process, smelting, slag-matte separation and matte converting are continuously carried out in series in three furnaces connected by launders. As a result of this operational configuration of the furnaces, influence of the change in operating condition in upper stream, such as variation of feeds in the smelting furnace, propagates to down stream with some delay. In order to achieve stabler operation, process control algorithm based on the dynamic characteristics of each furnace would be very effective. In this study, the dynamic process simulation model was developed for the smelting furnace. The model consists of two mathematical modules, i.e. the thermodynamic module and the mixing module. The calculation results using operating data obtained at Naoshima Smelter showed good agreement with the actually observed change in temperature, composition and flow rate of matte and slag at the outlet of the furnace. In addition, operation parameters such as reaction efficiency of oxygen and coal, dead volume of melts were estimated.

Jan 1, 1999

By Stein Tore Johansen

Some ferro-silicon fumaces have heat-recovery equipment. Here, the recovery of electric energy from the off-gases can be increased by increasing the off-gas temperature. This is easily done by reducing the amount of air which usually is mixed into the off-gas to cool the gas mixture. If the off-gas becomes too hot problems with severe fouling or clogging of the gas channels? close to the fumace is observed~ The result is irregular stops to clean the off-gas channels. The paper focuses on the nature? of the clogging phenomena and some of the ways to avoid clogging. A detailed experimental study was carried out at the Elkem Thamshavn Plant. Theoretical studies were performed to understand the particle deposition, turbulent multiphase fluid flow and off gas combustion in the off-gas channels. The study has resulted in reduced clogging.

Jan 1, 1992

By R. K. F. Lam

Unacceptable levels of impurity were noted in high purity chromium melting. Analysis of recent melting data determined that oxygen content in chromium is the critical parameter. Thermodynamics studies identify zirconia to be the most stable oxide in the presence of liquid chromium, followed by alumina and silica. Iron oxide reacts readily with liquid Cr. A certain degree of chemical reaction between liquid chromium and oxides does occur, contamination by the crucible is therefore unavoidable. Equilibrium constants indicate that a chromium oxide addition decreases 'ceramic dissolution and reduces impurity contamination. Safe operating conditions with oxygen content between 1190 ppm and 2500 ppm were identified. Additions of chromium oxide (Cr2O3) of 161 grams and 264 grams to liquid chromium yielded acceptable levels of impurity, and oxygen content was respectively increased to 1624 ppm and 2 179 ppm. A new process of melting high purity chromium with chromium oxide addition for controlling the activity of Cr2O3 is recommended.

Jan 1, 1997

By Osvaldo A. Bascur

Several new hydrometallurgical plants have been built in the past years. They have implemented new processes to treat new type of ores. New technologies have been used to improve metallurgical performance from the start. The cycle times between knowledge generation and innovation are often neglected in the traditional capital expenditures and building of these new process plants. The paper reviews several implementations in which they have started with new ways of using information management from the beginning. The implementation of a real time performance management infrastructure is reviewed to assist in the implementation of mine to product strategies, metallurgical mass balances, solvent extraction composition statistical process control, methods to minimize organic losses, reduce variable costs and to improve metal extraction. Several examples are provided to improve operations by simplifying the access and analysis of information from assets and metallurgical processes. Continuous improvement and innovations have been enabled to minimize start times and for faster troubleshooting and resolution of operational problems.

Jan 1, 2006

By F. Michael Hosking

Modeling of a furnace brazing process is described. The computational tools predict the thermal response of loaded hardware in a hydrogen brazing furnace to programmed furnace profiles. Experiments were conducted to validate the model and resolve computational uncertainties. The results from selected furnace simulations and measured thermal events were compared. Critical boundary conditions that affect materials and processing response to the furnace environment were determined. "Global" and local issues (i.e., at the furnace/hardware and joint levels, respectively) are discussed. The ability to accurately simulate and control furnace conditions is examined.

Jan 1, 1998

By Stein Tore Johansen

Some ferro-silicon furnaces have heat-recovery equipment. Here, the recovery of electric energy from the off-gases can be increased by increasing the off-gas temperature. This is easily done by reducing the amount of air which usually is mixed into the?off?gas to cool the gas mixture. If the off-gas becomes too hot problems with severe fouling or clogging of the gas channels close to the furnace is observed. The result is irregular stops to clean the off-gas channels. The paper focuses on the nature of the clogging phenomena and some of the ways to avoid clogging. A detailed experimental study was carried out at the Elkem Thamshavn Plant. Theoretical studies were performed to understand the particle deposition, turbulent multiphase fluid flow and off gas combustion in the off-gas channels. The study has resulted in reduced clogging.

Jan 1, 1992

By M. Zamalloa

Slag foaming is an important phenomenon in many metallurgical processes. It creates large surface areas for multi-phase reactions to take place. In other applications, it protects electrodes and improves the energy efficiency by reducing radiation from hot surfaces. However, it may also be a source of serious disturbances. To control and optimize the use of slag foams, an extensive knowledge of the factors controlling the foam formation and stability is required. Slag foaming experiments were carried out using synthetic FeO-CaO-Si02 slags at temperatures ranging from 1200 to 1350 "C. A data acquisition system was used to continuously measure the foam height, gas flow rate, bubble frequency and temperature. The experimental results show that the gas injection rate has a strong effect on the behaviour of slag foams. At high flow rates and rapid bubbling, unstable foams with short decay times were created. The addition of P20, favours the foam formation and stability by lowering the surface tension of the slag. The average foam life increases with decreasing basicity (CaO/Si02). It is proposed that this is attributed to the increase of the surface viscosity due to surface adsorption of a thin film of silica, retarding the drainage of the liquid films.

Jan 1, 1992

By N. Kanari

The kinetics of oxychlorination of MgO by C12+02 was studied in the temperature range of 850 °C - 1025 °C, using thermogravimetric analysis. The effects of C12/02 ratio, gas velocity, temperature and partial pressure of reactive gases on the reaction rate were investigated. The oxychlorination process was characterized by an apparent activation energy of about 214 kJ/mol. The reaction orders with respect to C12+02, C12 and 02 at 950 °C were about 0.65, 0.98, and -0.37, respectively. Some data about oxychlorination kinetics of MgO, Cr2O3, and MgCr2O4 contained in chromite were compared. Efficiency of using oxychlorination for the removal of iron oxides contained in magnesia was demonstrated.

Jan 1, 1999

By Thomas Havlik

It is proposed to realise the direct leaching, during which will be generated elemental sulfur and not sulfate or sulfuric acid as end product, under conditions that sulfur will not cover the leaching surface and Hot hinder the leaching course. The following improvements have been considered: -use of organic sulfur solvents -ultra high-frequency leaching -ultrasonic leaching -use of surface detergents or surfactants in leaching processes -simultaneously crushing and leaching These proposals are under investigation and preliminary results are promising

Jan 1, 1996

By Virgil Optasanu, Yvon Lacroute, Eric Lesniewska, Tony Montessin, Pauline Vitry, Eric Bourillot, Cédric Plassard

A general challenge in metallic components is the need for materials research to improve the service lifetime of the structural tanks or tubes subjected to harsh environments or the storage medium for the products. One major problem is the formation of lightest chemical elements bubbles or different chemical association, which can have a significant impact on the mechanical properties and structural stability of materials. The high migration mobility of these light chemical elements in solids presents a challenge for experimental characterization. Here, we present work relating to an original non-destructive, with high spatial resolution, tomographic technique based on Scanning Microwave Microscopy (SMM), which is used to visualize in-depth chemical composition of solid solution of a light chemical element in a metal. The experiments showed the capacity of SMM to detect volume. Measurements realized at different frequencies give access to a tomographic study of the sample.

Jan 1, 2015

By Cui Wang, Qian Li, Kexin Jiao, Haibin Zuo, Jianliang Zhang

Abstract：A rational cooling water system is the assurance for long campaign life of blast furnace．In the paper, the heat transfer of different furnace period and different furnace condition based on the water quality characteristics were analysed, and the reason of the heat flux over the normal from the hydrodynamics was analysed. The results showed that, the vapour-film and scale existence significantly influenced the hearth heat transfer, which accelerated the brick lining erosion. The water dynamic characteristics of the parallel inner pipe or among the pipes were the main reason for the abnormal heat flux and film boiling. As to the reasonable cooling water flow, the gas film and the scale should be controlled and the energy saving should be considered.

Jan 1, 2015

By A. J. Davidson

A novel sensor is described for the measurement of the copper content of copper matte. Due to the high copper concentrations found in matte, potentiometric sensors are not sufficiently sensitive. A highly sensitive sensor has been developed based on a modification of the amperometric technique using a copper ion conductor, Cusicon. The results correlate closely with the theoretical predictions.

Jan 1, 1998

By Go-Gi Lee, Jae-Young Jung, Myung-Duk Seo, Hyun-Na Bae, Seon-Hyo Kim

"Bubbles form at the anode during the electrowinning of magnesium and cause hydrodynamic acceleration and electrical field disturbance. A three-dimensional computational model was developed to investigate the effects of the geometry of the electrochemical chamber and the size distribution of bubbles on the fluid flow in the pilot plant. The results are validated by measurements of the surface characteristics of molten salt and the bubbles formed. Fluid flow at the surface was recorded with a high speed camera, and the distribution of bubble size is determined by inspecting the video images frame by frame. The measured size distribution of the bubbles is entered into the computer simulation of a multi-phase flow. A sloped roof is installed above the electrodes, to enhance the flow of the molten salt, thus resulting in higher current efficiency, lower energy consumption, and higher quality of magnesium metal.IntroductionTitanium's excellent properties of low density, high specific strength, high temperature strength, and exceptional resistance to corrosion are highly beneficial to diverse applications including aerospace, automotive, construction, and medical implants. Although the Kroll process[l] and Hunter process have been used for the extraction of titanium in the 20th century, their complicated engineering stages and high production cost, have led to further research into new processes such as FCC Cambridge, Armstrong and TiRO. Despite these intense research efforts, no process has yet been developed that is more economical than the Kroll process, by which most of the global commercial titanium is still being produced."

Jan 1, 2011

By Jyri Talja, Shaolong Chen, Hannu Mansikkaviita

"For optimum smelting results, proper treatment of the feed is needed to ensure favourable conditions for ignition characteristics, heat balance, mass balance with tolerable impurity levels, and overall process economics. Feed preparation consists of physical treatments before drying (blending), chemical treatments before drying, (roasting, if required), drying itself and physical treatments after drying (fractioning, if required).Effects of fluctuation on mineralogy and moisture should be minimized by blending the concentrates in a bedding plant prior to drying. As an alternative to drying, additional treatments such as roasting for impurity removal may be needed for part of the concentrate.Sustainability, energy efficiency, utilization of waste energy, low gas and dust emissions, product quality, availability and occupational exposure reduction are decisive criteria in drying today. These criteria are best met by the Kumera steam dryer, which has the best energy efficiency, zero CO2 emission, lowest operational and maintenance expenses, and superior availability and product quality.IntroductionFeed preparation plays a crucial role in having a smooth smelting operation and also the overall smelting economics in metal production. Therefore, it is of significant importance for all copper, nickel and lead smelter operations in which sulphide concentrates are fed to the primary smelting furnace. Generally speaking, the higher the metal content in the matte after primary smelting, the more important the feed preparation. This is of particular importance in the direct blister (DB) process for copper production and direct oxygen nickel (DON) for nickel production.Bedding is the first stage in feed preparation. This is very important for the sake of smoothing the mineralogical fluctuation in the feed for better smelting control. Its importance increases as the number of concentrates available for the feed mix decreases."

Jan 1, 2012

By Robert H. Hsu

Palladium finely dispersed in a substrate of kieselguhr, Pd/k for short, has been successfully used for hydrogen storage, separation and pumping for a number of years at the Savannah River Site (SRS). Recently SRS has developed a new pd/k flow through bed (FTB) prototype for separating hydrogen from other gases and simultaneously storing the hydrogen on palladium. The FTB uses single-pass liquid nitrogen cooling during hydrogen absorption/separation/storage and electrical heating for desorption/unloading of hydrogen. Fourteen absorption-desorption or loading/unloading cycles using hydrogen have been conducted with the new FTB prototype. Test results show that all design performance objectives have been successfully achieved: recover 295% of hydrogen gas from feed gas, produce 99.9% hydrogen product gas and < 5% hydrogen in discharge gas. This paper will discuss characteristics of the palladium-coated kieselguhr or diatomaceous earth, design and operation of the FTB, and results of performance tests such as separation efficiency, hydrogen storage capacity and system heat transfer characteristics.

Jan 1, 2002

By K. S. Jeong

Since the start-up of the Onsan Smelter in 1979, LS-Nikko Copper has grown into a competitive smelter through continuous development. Several environmental improvements have been carried out, in particular, intensive investments in reducing SOx emissions, such as de-sulfurization plants, fugitive gas capturing and TMS(Tele Metering System). In addition, in recent years LS-Nikko Copper has spent more than 10 million USD every year to improve environmental conditions. In order to be a global leading smelter in every aspect especially environmentally, LS-Nikko Copper plans to inspire environment-friendly minds, co-operate with shareholders, and participate in global conventions. This paper describes the environment improvements carried out at Onsan and briefly introduces a sustainable vision for a green smelter.

Jan 1, 2006

Many studies have been conducted over the past 3 decades on the leaching of gold in solutions containing thiosulfate, ammonia and copper. However, most of these studies have been carried out using ore samples, with very few fundamental studies of this system being attempted. The majority of the published studies have failed to acknowledge the undesirable side reaction between copper(H) and thiosulfate, let alone account for its effect. The fact that the solution chemistry is constantly changing makes it very difficult to perform a fundamental study of gold leaching. With the advent of the rotating electrochemical quartz crystal microbalance (REQCM), such fundamental studies are possible as this instrument measures mass in real time. This has allowed leach kinetics to be measured in a matter of minutes and hence at essentially constant solution conditions; The present paper highlights that a sufficient concentration of copper(II) and ammonia are required in order to achieve appreciable gold leach rates. However, the use of air (oxygen) to maintain the copper(Il) concentration catalyses the undesirable copper(II) reaction with thiosulfate. The presence of ammonium ions is shown to have an effect on this undesirable reaction as well as on the gold leaching ?reaction. Preliminary electrochemical studies into .gold electrowinning using the REQCM show that gold(I) thiosulfate cannot be readily reduced to metallic gold in the potential region at which cementation usually occurs. However, it is well known that gold cementation onto copper occurs rapidly. The current study addresses this discrepancy by studying the effect that copper and silver have on the reduction of gold thiosulfate. It has been found that the presence of both silver and copper enhance gold deposition, particularly at low over potentials. While this is beneficial in cementation, the presence of copper and silver in solution has been found to cause passivation of the cathode surface during electrowinning at &apos;higher overpotentials.

Jan 1, 1998

By M. Sahoo

The development of new alloys containing bismuth and selenium for potable water supplies are reviewed. The new alloys are replacements for the leaded red- and semi-red brasses by the low-lead alloys, SeBiLOYS I and II, for sand casting, and SeBiLOY III replaces the lead containing yellow brass, C85800, for permanent mold casting. As the new alloys use bismuth and selenium, the supply and demand of these elements are discussed. The key casting characteristics discussed are: tendency to dross formation, freezing range (liquidus and solidus temperatures), fluidity, resistance to hot tearing, microstructures, mechanical properties, machinability, grain refinement and corrosion behaviour.

Jan 1, 1999

By Xinghui Meng

The recovery of platinum and palladium from automotive catalysts has been investigated by leaching in iodide solutions with oxidants including oxygen and iodine in an autoclave. An ammonium salt was presented in a neutral leaching solution as a key leaching reagent to achieve high recoveries of the platinum group metals (PGM). The effect of temperature, and concentrations of oxidants and of ammonium salt on the recovery of PGM was examined. Under the experimental conditions studied, the recovery of platinum and palladium was found to be greater than 95%. An economical assessment of this process has also been examined and discussed.

Jan 1, 1995

By Ricardo Badilla-Ohlbaum

Copper has been used by man for a very long time and unlike certain other metals, it is an essential element for life. Its toxicity arises both from a deficit and excess copper exposure/intake. The focus of the current discussions in countries of the European Union (EU) and in some USA States, is based on the concerns, independent of the scientific facts and the economic status of these claims, of the negative influence of copper and other metals on health and the environment. These discussions have influenced the new regulations of copper in drinking water, and the approach to regulate the appropriate levels of copper in surface water, soils and sediments. To illustrate the challenges ahead for copper, the evidence by which the current US Environmental Protection Agency (USEPA), the World Health Organization (WHO) and EU recommendation and regulations regarding copper in drinking water have been derived is presented and discussed. The gaps between the demands for new standards of health and the environment and the practical scientific tools to achieve these goals are presented, and the need to develop new regulating paradigms is also illustrated. The introduction of methodologies for the regulation of essential elements and acute inorganic substances in drinking water is discussed, as well as the status of the present approach contained in the International Program of Chemical Safety Environmental Health Criteria, (EHC) N° 170. The impact of the possible restrictions on the use of copper in the EU because of health and environmental concerns in terms of the world market for copper is discussed.

Jan 1, 1999