Search Documents

By Judy Che, Steven Ceccio, Gretar Tryggvason

"A detailed understanding of drop deformation and solidification is essential for quantitative predictions of geometry and properties of parts made by ballistic particle manufacturing processes. Axisymmetric results of towers built by the deposition of multiple drops are presented. In these computations, fluid flow, heat transfer, and phase change are fully coupled throughout the drop deformation and solidification process. The solution method is based on a single set of conservation equations written for all phases simultaneously. The phase boundaries are treated as imbedded interfaces by adding the appropriate source terms to the conservation equations. A parameter study demonstrates the effect of Weber number, Peclet number, and drop deposition frequency on the final shape of the structure. Numerical results show that most successful method of building uniform towers is when two conditions are met. First, each drop solidifies at the same time in the deformation cycle. Second, the cooling rate is slow enough to allow for good adhesion between drops. The ability to predict the final shape of deposited drops will greatly reduce the amount of experimentation necessary to select the desired set parameters for any artifact.IntroductionMaterial deposition techniques based on layering small molten metal drops holds the promise to build small, coherent three-dimensional structures. In this process, numerous 20-100 µm diameter drops are deposited onto a substrate with a low impact velocity (on the order of 5 mis). Both the momentum and trajectory of each drop are controlled precisely to build up complex parts. This material layering technique differs from processes such as spray forming and splat quenching which involve high impact velocities (on the order of 100 mis) and high frequency deposition with little control over individual drop placement. This process of layering small drops can produce parts with near net shape accuracy, while spray forming produces slabs of material which must then be worked to make a usable part. The ability to computationally predict final drop shape and cooling rate has the advantage of allowing the user to select parameters to produce parts with desired shape and mechanical properties. However, the development of such predictive methods requires a thorough understanding of both drop deformation and solidification"

Jan 1, 1999

By S. J. Gerdemann

The U.S. Bureau of Mines is studying the kinetics of wet oxidation of sphalerite concen- trate (ZnS) as a possible process for a gravity-pressurized reactor (GPR). At tempera- tures in excess of 200' C, a sphalerite water slurry will react with 0, to form zinc sul- fate (ZnSO,). However, the pressure required to keep the water from boiling at these temperatures has kept this reaction from becoming a viable continuous process. The GPR can easily obtain the high pressures required for this reaction. The reaction rate is complicated by the solubility of 0, in water and the further oxidation of ZnSO, to insoluble zinc oxysulfate (Zn4(OH),S04.4H20). The effects of pressure, temperature, and particle size on the rate of reaction were investigated. Reaction rate was found to be limited by the amount of oxygen in solution. However, at 250" C and 1500 psia, over 90 pct of the zinc was solubilized in less than an hour. The conditions for maxi- mizing the Zn++ in solution, while minimizing oxysulfate formation, are discussed.

Jan 1, 1993

By Yanhui Sun, Yanan Zeng, Kaike Cai

"Hot ductility of Nb-V-containing steel has been studied by theoretical calculation and thermal simulation experiment. Meanwhile, microsegregation and precipitates were analyzed. The results showed that segregation degree of elements S, P, 0 is greater in mushy zone, while, the hot ductility was deteriorated by inclusions of Fe(S,O), (Fe,Mn,Si,Al)(S,O) in the interdendritic region. At the temperature 1100°C, a few NbN particles, 60-70nm, have little effect on mechanical property. In the temperature range 1000°C to 975°C, R.A declined rapidly from 82.36% to 69.61% with the diameters decreasing from 20 to 10nm and quantity of particles increased 23 to 45inds/µm2, respectively. In the temperature range from 900°C to 850°C, R.A reduced unobviously from 34.27 % to 30.01 % with ferric films thickening gradually. The critical stress, 52.38MPa, was equal to tensile strength at 975°C. Intergranular fracture was easy to occur with higher critical stress below 975° C.IntroductionProductivity and product quality of slab are seriously affected by cracks during continuous casting and the influencing factors of cracks are various[l]. From microcosmic angle, resisting deformation ability of initial solidification shell decreases obviously with solute elements segregation which can urge the low melting point ofliquid film to form at grain boundaries[2, 3]. Meanwhile, with temperature decreasing, particles would precipitate as the practical solubility product is greater than equilibrium solubility product. The carbonitrides would lead to stress concentration at austenite grain boundaries. Therefore, the transverse cracks of microalloyed steel would form during the straightening operation in the continuous casting process. The hot ductility of steels in the temperature of mushy zone was characterized by microalloy elements segregation, zero strength temperature (ZST) and zero ductility temperature (ZDT). The nature, shape, and size of precipitates have been investigated by TEM (JEM2100). Hot tensile test with low strain rate was simulated by Gleeble-1500. The objective of present study is to provide reference for zero defect of microalloyed steel during continuous casting process."

Jan 1, 2013

By G. Scavino

A 0.5 wt.% C, 22 wt.% Mn austenitic steel, recently proposed for fabricating automotive body structures by cold sheet forming, due to favorable overall strength and ductility, exhibits plastic localizations during uniaxial tensile tests, whereas no localization happens during biaxial Erichsen cupping tests. Full-thickness tensile and Erichsen specimens, cut from as-produced sheets, were polished and tested at different strain rates. During the tensile tests, the plastic localization phenomena consist first of macroscopic deformation bands traveling along the tensile axis, and then of series of stationary deformation bands, each adjacent to the preceding ones; both types of bands involve the full specimen width and yield macroscopically observable surface relief. No comparable surface relief was observed during the standard Erichsen tests. The stress state being known to influence plastic localization phenomena, reduced-width Erichsen tests were performed with 10 to 30 mm width polished specimens, in order to explore the transition from biaxial to uniaxial loading.

Jan 1, 2009

By Leonel Contreras

The gas treatment system, MALIGAS (in Spanish MAnejo y Llmpieza de GASes which means handling and cleaning of gas), is part of the Codelco-Chile Potrerillos Smelter decontamination plan; which includes the newly designed system for the cooling and cleaning of the gas generated from a Teniente Converter and four Peirce Smith Converters. The gas generated in the process is captured by water cooled hoods and mixed with air. Then the gas enters a cooling pre-chamber which utilizes a water cooled screen to capture and remove the coarse and semi-fused particles. At this stage; the gas loses a portion of its heat with temperature falling below 608°C which is a necessary condition to avoid damage to the pipes, ducts and other metallic structure of the gas handling system. The gas is further cooled at the Radiation Cooler to a temperature ranging between 315 and 380°C. The gas is conditioned to avoid damage to the electrostatic precipitators that are designed to clean the gas by removing significant amount of dusts from the: gas stream. This gas stream is currently discharged to the stack, however, it will be treated in a sulfuric acid plant that is currently under construction and is scheduled for commissioning during the second half of 1999. The gas handing and cleaning system has been operated without any significant interruptions. Minimal emissions of SO2 and dusts in the work place are noted. The system requires minimum maintenance. The key to the high availability of the system is due to the good, performance of he Radiation Cooler, which efficiently cools the gas before entering the electrostatic precipitators (ESPs). This enables the ESPs to remove the dusts efficiently.

Jan 1, 1999

By J. E. Dutrizac

Mineralogical studies were carried out on nodulated copper cathodes from three primary refineries to characterize the nodular growths and to elucidate the causes of the nodulation. Nodulation is often initiated at the surface of the starter sheet or the stainless steel plating blank, although a layer of smooth copper sometimes is deposited before nodulation commences. In some instances, the "roots" of the nodules exhibit a pronounced dendritic texture that is associated with an abundance of cavities. Slimes particles are not usually associated with these growth features which lead to a globular surface deposit. The globules sometimes develop into larger nodules, and this type of nodulation is likely caused by improper addition agent concentrations. The nodules on most cathodes, however, exhibit "roots" at the contact with the substrate that are associated with microcavities and large clusters (>40 µm) of slimes particles. The slimes constituents are commonly Ag powder, PbSO4 and Cu2(Se,Te) but not AgCu(Se,Te) or Ag,(Se,Te). The size of the slimes clusters, rather than their composition, appears to be the important factor causing the copper to grow into nodules. Tiny individual slimes particles themselves do not appear to cause cathode nodulation.

Jan 1, 1999

By M. Okido, R. Ichino, K. Kuroda

"Compound semiconductor, ZnTe, was electrodeposited in an acidic solution with K2TeO3, ZnSO4 and Na2SO4 solution. Since the reduction potential Te(IV)/Te(O) is remarkably noble from the solution comparing to Zn(II)/Zn(O), code position of Te and Zn was thought to be difficult from this solution. Resulting from EQCM analysis, furthermore, Te(IV) reduced to Te(O) and Te(-II) in this order so that Te catholically dissolved from the electrode surface at more negative potential. But ZnTe alloy were formed by the UPD of Zn at -0.7V at 298K on Te surface in lmM K2TeO3, 100mM ZnSO4 and 100mM Na2SO4 solution adjusted at pH 4. Content of Te in the deposits is, however, more than 80%.Electrolytic temperature is well known to affect on the deposits characteristics. The higher bath temperature was, the better ZnTe crystal was detected in this study. Thermal electrode method is a. process of heating only substrate by flowing ac current in substrate. This process makes the surface temperature of substrate higher than boiling point of the solution, 373K. From EDX analysis, deposits without thermal current were Te-rich, Te content in the deposits with thermal current decreased with increasing of thermal current. Te content was 62% for 5A ac current, 51 % for I OA and 45% for 20A, respectively. The deposits that produced with ac current of IOA were closed to the stoichiometric ratio, i.e. ZnTe.Consequently, thermal electrode method is more effective to obtain a good crystallized ZnTe without heat treatment after deposition.IntroductionThe current subject of solar cell materials is silicon. Compound semiconductors including GaAs and II-VI group are generally used in the developing field of digital information such as the rapid cellular phone and car telephone. Compound semiconductors consist of more than 2 kinds of element. There are many materials for these compound semiconductors such a SiC, InSb, CdS for binary system and CuinSe2 for ternary system. It becomes generally difficult, to produce high quality crystal with increasing of kinds of element due to a complicated structure and a compound ratio of element. Semiconductor materials as a device are usually simple binary compounds and/or these mixed crystals. Properties of compound semiconductors have variety of the forbidden band and lattice constant and that can be change easily by addition of another element for the usage of the solar cell. Since most compound semiconductors are direct interband transition type, which has steep optics absorption edge and large light absorption coefficient."

Jan 1, 2000

By K. V. Sreenivas Rao

Solidification experiments have been conducted to study the effect of interface heat flux and air gap formation on cooling rate of the casting during solidification of Al-4.5wt%Cu alloy. The thermal history of the casting and mold during solidification is recorded using thermocouples connected to computer interfaced data logger. The measured temperatures in the mold are used as input to the IHCP (inverse heat conduction problem) algorithm for simulating multiple heat flux components at the boundary. It is observed that the filling effects induce spatial variation in the thermal field in the mold and casting regions and greatly influence the cooling rate of the casting. The study demonstrates the use of IHCP and in-situ measured thermal profile in analyzing the cooling rate and microstructure.

Jan 1, 2008

By Angus Hellawell

The application of the common tangent principle to free energy - composition surfaces is considered. It is shown that the construction requires that single phase surfaces on either side of a two phase volume must always exhibit the same sign of curvature - contrary to that shown in many published phase diagrams. In general, these curvatures will be such that the surfaces are mutually concave towards the more stable phase. A number of examples are discussed.

Jan 1, 1991

By T. T. Chen

The manganese oxide scales, consisting mainly of MnO2, characteristically occur in banded colloform structures which adhere to porous layers of PbSO4 and PbO2 that oxidized from the rolled Pb-0.7% Ag anodes. Hydrous Mn oxides, Mn3O4 and amorphous Mn oxides are believed to be also present. Tiny particles of gypsum, PbSO4, SrSO4 and AgCl are entrapped in the colloform masses. The gypsum originated from the Zn electrolyte; strontium carbonate was added to the ZnSO4 solution to control Pb, and silver originated from the anodes. Some of the colloform bands contain minor amounts of Pb, implying a limited degree of dissolution of the Pb during electrolysis. Other colloform bands incorporate trace amounts of Zn. Colloform structures permeated with silica gel are presumably caused by the high silica content of the electrolyte.

Jan 1, 2009

By D. Georgiou

Direct sulphuric acid leaching of nickeliferous limonites is the process of choice to recover nickel and cobalt from equatorially located lateritic ores. These ores are rich-in-iron (-45 wt%) existing in the form of goethite enriched with nickel. The merit of this process is due to its high nickel selectivity because of simultaneous iron separation and acid regeneration. Under acid leaching conditions (-250 to 270°C) iron follows an acid dissolution-hydrolytic precipitation path yielding a very low concentration level depending on temperature and acidity of the final leach liquor. The primary precipitation product of iron is hematite which also forms as a scale on reactor internals along with co-existing aluminum. In this paper, an overview of the behaviour of iron solid products under process conditions is made. The evolution of goethite to hematite transformation, as well as the role of iron in reactor scale production, are studied using SEM/EDX characterization techniques.

Jan 1, 1995

By Kimura. E.

Continuous estimation of phosphorus content of molten copper is required to produce phosphorus deoxidized copper in a continuous casting operation. The phosphorus content of molten copper was related to its electric resistivity, which was measured by the four-probed technique with a specially-shaped cell. In a laboratory scale, the linear relationship between the above factors was confirmed in the temperature range of 1083OC through 1200°C. The phosphorus concentration range measured was from 40 to 500 ppm. The phosphorus content was monitored successfully by measuring the electric resistivity of the molten copper in the distributor of a continuous caster in an industrial scale.

Jan 1, 1992

By Joel Anderson

Allvac 718Plus is a newly developed superalloy with a good potential for use in fabricated aircraft engine structures when service temperatures exceed 650°C; the limit for standard alloy 718. Fabrication involves welding, where cracking usually is a prohibitive factor. Comparison of the solidification cracking behavior between these two alloys was made by Transvarestraint testing. It was shown that the total amount of cracking was significantly lower for 718Plus alloy, which was associated with a lower amount of ?/Laves or ?/NbC eutectic-type constituents. This in turn is believed to be due to the lower iron content of the Allvac 718Plus material. The analysis of alloying element segregation both within primary dendrite and interdendritic constituents clearly indicates that the segregation of Nb is the controlling factor in determining the final solidification microstructure in these alloys. The Nb concentrations of these constituents are significantly higher compared to the bulk alloy concentration. This was confirmed by the SEM-EDS analysis and calculations assessed with JMatPro, the latter also indicated that alloy 718 is more prone to form Laves and NbC eutectic-type constituents compared to Allvac 718Plus material.

Jan 1, 2008

By Ch. -A. Gandin, M. Rappaz

"The grain selection mechanism which occurs during the growth of columnar dendritic structures is routinely used in the investment casting industry to produce directionally solidified (DS) and single crystal turbine blades. However, the evolution of the grain density with increasing distance from the chill has rarely been correlated with the evolution of the grain texture. This contribution presents a three-dimensional (3-D) stochastic modeling approach which permits the computation of grain maps, pole figures and grain density evolutions in DS superalloys. These predictions are compared with measurements resulting from an automatic indexing technique of Electron Back-Scattered diffraction Patterns. This 3-D stochastic model, which applies to uniform temperature situations, has to be extended to the dendritic growth in a thermal gradient. As a preliminary step, a 2-D Cellular Automaton (CA) has been coupled recently to Finite Element (FE) heat flow computations in order to predict the grain structures in complex shape investment cast part. The application of this CAFE model to the investment casting of a turbine blade is presented. Considering these results, the extension of the CAFE algorithm to three dimensions is discussed.INTRODUCTIONThe selection of columnar grains during the directional solidification of alloys plays a key role during the investment casting of directionally solidified (DS) and single crystal (SC) components for aerospace applications [I]. This selection mechanism, leading to a competition of the dendritic network propagation at grain boundaries, has been the subject of many investigations. In particular, the study of Walton and Chalmers [2] is remarkable since it provides a link between the evolutions of the density and of the texture of columnar grains with increasing distance from the mold wall. Since this original work of Walton and Chalmers, two new tools have become available, which enable one to revisit the problem of grain selection in much greater depth. The first one is a fully automatic indexing technique of Electron Back-Scattered diffraction Patterns (EBSPs) [3-6] which directly gives the crystallographic orientation of the solid at any location of the specimen. Pole figures, orientation distributions, misorientations between grains can be visualized very easily with this technique. This information can be directly compared with the results of a second tool: a three-dimensional (3-D) stochastic model (SM) describing the nucleation and growth of grains in a uniform temperature field [6-9]. In order to extend this model to non-uniform temperature situations, a preliminary 2-D model has been developed [10]. It is based on a Cellular Automaton (CA) algorithm coupled with Finite Element (FE) heat flow computations. Since the details of both the automatic indexing technique of EBSPs and the simulation tools have already been published [3-10], only a brief summary is given here."

Jan 1, 1994

By Ephraim Jeya Kumari

The demand for the titanium dioxide pigments and the shortage of higher-grade titaniferous ores with low radioactivity and zircon sands worldwide has encouraged the development of new techniques for the beneficiation of lesser grade titaniferous ores. The inferior quality ores are invariably richer in radio-active and lanthanide oxides, which severely interfere with the fluidized bed chlorination reaction (FBCR), in which ultra-high purity titanium tetrachloride is distilled off for pigment manufacture. However the present beneficiation techniques require high quality ilmenite ores and are not suitable for upgrading lower grade ilmenite ores which do posses trace metals in the form of lanthanides and actinides as Al-phosphates and zirconium silicates, respectively. The presence of mineral hosts, zircon sand and monazite in ilmenite and anatase also increase in chlorine gas consumption in the FBCR and contribute to a larger volume of hazardous waste production, which must be neutralised at a significant cost before being disposed off safely. In view of the problems described for lanthanide (Ce, Nd etc) and actinide (Th, U) trace impurities in titaniferous ores, an alternative route, which is flexible and more accommodating for processing difficult ores, is discussed. In the new process, which may be used for richer grades of ores too, the ore is roasted in air with sodium carbonate below 950°C to promote the formation of water-soluble sodium ferrite and insoluble sodium titanate phases. In this investigation, the high-temperature roasting process and the ensuing hydrometallurgical leaching steps have been analysed in the context of selective separation of lanthanide and actinide minerals from the main titaniferous mineral structures. Evidences for the selective separation are presented based on the chemical (XRD, XRF, AA) and microstructural analysis (SEM, EDX, EPMA) of roasted mass and the leached product. The efficiency of selective separation is also reported based on the chemicals analysis and the particle size of the materials derived after leaching. The paper highlights the various thermodynamic aspects of reaction equilibrium in the Fe-Ti-O-Na system, and the effect of Eh-pH diagram in the determination of pH required for the better control of the removal of iron and sodium. Two different types of Ti ores, namely ilmenite and anatase, their crystal structure and the phase transformation will also be explained on the basis of wet chemical analysis, XRF, XRD, EPMA and SEM-EDX studies. The method developed examines the technological feasibility of the selective separation process.

Jan 1, 2006

By J. T. Stanley

The identification of crystal phases and crystal chemistry can be critical to understanding the mechanisms of waste material interaction with native soils. Understanding these mechanisms can suggest correct methods for remediation and treatment. A program is outlined and examples are given of the development of effective techniques for rapid phase identification of environmental samples using electron microscopy. The program concentrates on the development of integrated object oriented software to aid rapid searching of online databases and rapid simulation of potential crystal diffraction patterns. Examples come from dried sludge taken from a former hard-chrome plating facility.

Jan 1, 1993

By Cesar O. Gomez

A procedure has been developed for mounting at random particles of mineral samples to be characterized using image analysis. The procedure is based on the generation of a random distribution of sample particles in particles of a diluent material. and the embedding of this particle mixture in an epoxy resin without disturbing the initial distribution. Two materials with atomic number similar to that of the epoxy resin were successfully used as diluents: activated charcoal and graphite. The proportion of diluent material to be mixed with the sample to have a large number of mineral particles in the field of view while keeping the occurrence of touching particles at an acceptable level was determined empirically. The randomization achieved with the procedure developed in this work was tested using as samples known mixtures of silica and pyrite particles of the same sieve class. The agreement obtained between the mass ratio of minerals used in the preparation of a particular specimen and that resulting from image analysis demonstrates that the procedure developed is successful in producing a specimen where the embedded particles are randomly distributed.

Jan 1, 1988

By M. Rosales

By a physical and mathematical modeling, the behavior of the tri-dimensional waving, and the movement of the gases at the Teniente Converter was studied. The mathematical model considers the condensed phases of white metal and slag, along the gas phase, and includes the k-e model for the turbulence description. Both the physical model and the mathematical model allow to conclude that from a fluidynamic stand point the Teniente Converter clearly can melt 3000 tpd of concentrates. Also, both models are suitable to predict the slag fluidynamics and its spacial distribution inside the Teniente Converter, and the splashing in the tuyere zone as well.

Jan 1, 2006

By Ying Li, Xuling Chen, Xiaohui Fan

"In the sintering process, the behavior and performance of iron ores is extremely complex. Different minerals have different sintering properties. In order to use iron ores rationally and effectively, multilevel fuzzy evaluation method is used to establish the comprehensive evaluation model of iron ores. Because of the relative independent characters of iron ores in sintering process, the characters can be divided into physical and chemical properties, granulation performance, and sintering properties, are divided, and together with iron ores prices as the first level index for judging, which are used as the second level index for judging. Using the analytic hierarchy process (AHP) to determine the weight of each index, which is used as the second level index. The relative membership matrix is determined by triangular membership function, the comprehensive evaluation model is established.IntroductionIn China, sintering is the main method for iron ores agglomeration. Sinter accounts for more than 80% of the blast furnace. Sinter production in the iron and steel enterprises in China plays an important role[l-2]. As the main raw material of iron ores sintering, the objectivity and integration of iron ores evaluation is essential. The iron ores evaluation methods include of metric ton price evaluation method, iron grade of a single iron ores sintering, acid-base balance method, composition assessment method and other methods which are based on the chemical composition and physical properties of iron ores to measure the quality of iron ores[3]. The high-temperature mineralization is an important process in sintering process, which affects the structure and mineral composition of the sinter, and has a close relationship with the quality of the sinter[ 4]. Therefore, in consideration of the physical and chemical properties, granulation properties, mineralization performance and sintering properties, the iron ores are evaluated by multi-level fuzzy comprehensive evaluation. The multi-level fuzzy comprehensive evaluation method makes a comprehensive evaluation, applying fuzzy transform principle and maximum membership degree principle, considering a number of factors related to the things which are evaluated. The method has lower requirements for the amount of data, and which integrates qualitative with quantitative judgment. It has a unique advantage to make up for the deficiencies of traditional evaluation methods. It also can comprehensively evaluate the iron ores in a relatively short period, reduce a lot of experiments, improve efficiency and guide the sinter production[5-6]."

Jan 1, 2013

By Shize Jin

Effect of four polyols, namely ethylene glycol (EGL), glycerol (GCL), propanediol (PDL), butanediol (BDL) and three organic acids, namely oxalic acid (OA), malonic acid (MA) and succinic acid (SA) on the current efficiency (CE) and the cell voltage during zinc electrowinning was studied. Galvanostatic polarization was conducted in a supporting electrolyte (SE) containing 180 g dm-³ H2SO4, 60 g dm-³ Zn2+ and 8 g dm-³ Mn2+ at 38°C with magnetic stirring. The imposed current density was 50 mA cm-². The anodes were made of a Pb-Ag alloy and the cathodes were made of an aluminum alloy. The results showed that all the polyols tested in this study decreased the current efficiency and the cell voltage, but the decrease of the cell voltage was not important. Oxalic and succinic acids decreased the current efficiency to a less extent than the polyols, but did not decrease the cell voltage much. The only compound that increased the current efficiency was malonic acid, and its capacity of decreasing the cell voltage was the highest within the seven tested organic compounds.

Jan 1, 2003