Search Documents

By Tom Blevins, Roland Walker, Jinsheng Chen

"The Dywidag-Systems International DSI Tandem Anchor bolt, with an improved expansion shell-washer design, can substantially reduce potential entry roof falls caused by twisted or deformed expansion shells of the traditional mechanical anchor bolts during installation. In addition, the improved anchorage system can also ensure that a consistent and high installed load is achieved, which is critical for effective beam building under thinly laminated or layered roof conditions. This paper discusses the genesis and anchorage performance of the Tandem Anchor bolt, and analyzes the tension/torque relationship of different mechanical shell anchors using data obtained from both lab and field tests. It also discusses roof bolting mechanisms, roof bolting systems, and factors influencing effective beam building. Finally, numerical modeling was used to analyze the effect of bolt pretension magnitude on entry roof stability.INTRODUCTIONThroughout the history of underground mining, keeping the roof from uncontrollable collapse has been the greatest concern of the miner. Tremendous strides have been made in better understanding, predicting, and supporting the mine roof. This conference has spent the last twenty-eight years sharing information and distributing it to the mining community. A paraphrased statement from former Secretary of Defense Donald Rumsfeld adequately describes the challenges to the mining engineer as it pertains to roof control: it is a study of known knowns, known unknowns, and unknown unknowns. It is the hope of the authors to address some of these unknowns.The paper discusses the development of bolt anchorage systems from dry shells to shells with resin-assisted anchorage. It looks at some of the issues faced with the anchorage shells being used when introducing the insertion pressures caused by resin cartridges. The rationale behind the shell design changes was to compensate for this resin induced stresses.An improved expansion shell assembly (a slotted expansion shell base, a tapered cramming plug, and a novel support nut with tapered top) for mine roof bolts makes up the Tandem Anchor (U.S. Pat. No. 6742966); this minimizes the possibility of twisting seen with traditional mechanical shells and thus prevents springy bolts and shell leaves from breaking. A fully grouted Tandem Anchor bolting system has the advantages of both the pure mechanical point-anchor and the non-pretention fully grouted bolting systems. Once installed, the installed load or pretension will be locked in and never bleed off. Compared with the fully-grouted (2-speed resin) tension rebar bolting system, the fully-grouted Tandem Anchor bolting system can (a) reduce bolting cycle time (about 15 seconds per bolt), boosting coal production and productivity; (b) provide a greater installed load or pretention; and (c) achieve a consistent tension/torque ratio, which gives better bolting quality control. Therefore, a fully grouted Tandem Anchor bolting system is the most effective means to reinforce a weak rock mass intrinsically by the theory of beam building. For thinly laminated or layered roof conditions, a higher installed load or pretention (50% or more of the bolt's yield strength) can make a roof bolting system much stiffer, which results in less roof movement. Numerical modeling results show that the magnitude of the roof's tensile stress and relaxation zone can be substantially reduced under a higher installed load or pretention."

Jan 1, 2010

By Jinwang Zhang, Zhaohui Wang, Jiachen Wang

"Thick coal seams (seam height larger than 3.5 m) account for a large portion of the proven coal reserves of China, and underground thick coal seam mining provides about 50% of the Chinese annual coal production. Such seams are mainly mined using the longwall top-coal caving (LTCC) method. For safe and successful mining, a number of analyses on the stability of surrounding rocks in the LTCC face area have been extensively performed, and certain research achievements have been made. This paper introduces the main findings on rock pressure occurrence in the LTCC face during the last few decades and presents face and roof stability control techniques. INTRODUCTIONUnderground thick coal seams in China provide 1.8 billion tons of coal every year, which accounts for approximately 50% of the total Chinese annual coal production and 25% of the world, indicating that thick coal seams stand an important position in Chinese coal mining industry (Wang, 2005). Before the 1980s, thick coal seams were mined mainly by using the multiple-slice mining method. With the improvement of mining techniques and equipment in last two decades, longwall top-coal caving (LTCC) and high-seam, single-cut longwall are employed for thick coal seam extraction, offering advantages over multiple slicing from entry excavation and production perspectives (Wang, 2013).. The primary author of this paper introduced the most popular thick coal seam mining methods in China at the 30th ICGCM (Wang, 2015). This paper presents the stability of surrounding rocks in face area and ground control techniques for mining thick coal seams. For traditional longwall faces (seam height less than 3.5 m), the well-developed VoussoirVoussoir beam theory has been successfully used to analyze the movement of overlaying strata, which indicates that ground control techniques have become mature for this mining system. In such faces, the four-leg support with loading capacity of 4000–8000 kN is considered adequate for safe and successful mining. These faces normally have an annual yield of 1–2 million tons (Wang, 2007). For thick coal seams, however, the traditional support becomes inadequate and the ground control problem change to be more difficult and complex. Thus, development of large-scale mining equipment and ground control techniques for enlarged mined-out space and entries have been recognized as the most basic technical problems in mining thick coal seams."

Jan 1, 2017

By Katya V. Babenko, Victor V. Nazimko

We address the problem of the stochastic nature of ground pressure manifestation. Stress distribution in a rock mass and ground irreversible movement are governed with a set of random factors that affect the over-peak strength of the rocks, making them extremely sensitive to any perturbation of the external environment and to internal fluctuations of the thermodynamic state of the rock. We investigate the fluctuation evolution during a longwall face movement to find out whether the fluctuation dissipates or builds up. Five adjacent powered support failures simulate the ground pressure fluctuation. The main roof has been presented as a plate that reposed on the rigid base. The stiffness of the base depends on the thickness of the extracted coal seam and on the dilation of the caving roof. Maximum stiffness occurs in situ, and minimum stiffness is in the gob when the roof is highly flexible and subsides elastically, without caving. The more stress acts in the roof, the higher the cavity that occurs and the larger increment of the base stiffness. The wave of the fluctuation has extended both to the direction of the longwall advance and along the face from the point of the fluctuation agitation. There was an incubation period when the fluctuation was negligible, and the process of the main roof caving remained unaffected. The distance of the longwall advance during the incubation period was twice the longwall length when the fluctuation magnitude was 1% relative to the maximum possible disturbance and 0.76 of the longwall length for the magnitude of 24%. However, the pattern of the roof caving has dramatically changed during further movement of the longwall. All caving parameters have changed: step of the caving, ground pressure distribution, and the manifestation in the longwall and entries. A histogram of the fluctuation magnitude is symmetric in accordance with normal distribution. However, the distribution has abnormal excess. These findings are the first step toward answering the question whether it is possible to forecast the process of main roof caving and weighting consistently. Our preliminary conclusion is that the space and time intervals where this prediction can be made with certain reliability are limited, so further investigation is needed.

Jan 1, 2017

By David Hill

"End of panel longwall face recovery is almost certainly the most involved recurring geotechnical problem faced by operators, with major loss potential should problems occur. The paper presents Australian experiences and updates the outcomes of an industry sponsored research project on the geotechnical issues associated with conventional longwall recoveries.A number of critical features of the geotechnical environment, support design and mining geometry have a pronounced impact on ground control during face recovery. A model of roof behaviour at the take-off point has been developed and validated. Key geotechnical issues include low roof competency, an adverse weighting environment, geological structure, horizontal stress concentrations at the gate ends and the capacity and. integrity of the shields. All of these are identifiable either at the support design stage or, at worst, prior to the start of powered support removal, which is the critical stage of the recovery process.Key aspects of the geometry and process are the ability to maintain powered support resistance during bolt-up and recovery, the direction of shield removal, the impact of chutes and the speed of the shield removal process.The author presents case studies that illustrate these issues and the associated ground behavior.INTRODUCTIONEnd of panel face recovery is almost certainly the most involved recurring geotechnical problem faced by operators, with major loss potential should problems occur. However, unlike most geotechnical aspects of coal mining, very little research has historically been undertaken on the issue of conventional longwall recoveries. This is in marked contrast to the design of pre-driven recovery rooms, an issue which has attracted considerable research interest (Thomas, 2008). In 2006, Strata Engineering completed an Australian industry (ACARP) sponsored research project aimed at defining and minimising the geotechnical threats during longwall face recovery (Strata Engineering, 2006). The research project had the overall objective of developing guidelines for the specification of ground control strategies, so as to minimise the likely geotechnical threats relating to the safety, operational costs and production delays associated with the recovery of a longwall face."

Jan 1, 2010

By William G. Pariseau, Mark K. Larson, Douglas R. Tesarik, Heather E. Lawson

"This contribution describes development and application of a user-friendly finite element program, UT3PC, to address three important problems in underground coal mine design: (1) safety of main entries, (2) barrier pillar size needed for entry protection, and (3) safety of bleeder entries during the advance of an adjacent longwall panel. While the finite element method is by far the most popular engineering design tool of the digital age, widespread use by the mining community has been impeded by the relatively high cost of and the need for lengthy specialized training in numerical methods. Implementation of UT3PC overcomes these impediments in three easy steps: First, a material properties file is prepared for the considered site. Next, mesh generation is automatic through an interactive process. A third and last step is simply execution of the program. Examples using data from several western coal mines illustrate the ease of using the application for analysis of main entries, barrier pillars, and bleeder entry safety.INTRODUCTIONRational design of safe underground entries and crosscuts, barrier pillars, and bleeder entries begins with a site-specific analysis of stress. An analysis of stress identifies the critical regions of high-stress concentration where yielding is likely and additional or more focused ground control measures are needed. This analysis also identifies regions where stress concentration is low, and risk mitigation is less urgent. Displacements induced by mining, including roof sag, floor heave, and pillar squeeze, are also of importance to stability. The popular finite element method is well-suited for such analysis and has been in use for studying coal mine engineering problems since the late 1960s (Dahl, 1969). The method has been taught in undergraduate engineering curricula for many years and offers an alternative to existing design procedures based mostly on rules of thumb, empirical methods based on mine data, and predigital-age concepts of strata mechanics. However, despite the versatility of the finite element method, usage has been limited, mainly because of the cost of the software and the required training in numerical methods.The program UT3PC (Pariseau, 2017) has evolved from early two-dimensional versions in the era of mainframe computers. These early versions were still quite limited using only a few hundred elements that required overnight turnaround times. Recent versions of UT3PC are convenient and efficient desktop programs that use several million elements. With the advent of personal computers in the mid-1980s and subsequent increase in computer speed, expanded memory, and lower costs, applications for mining increased in three-way cooperative projects among industry, the former U.S. Bureau of Mines, and academia. The Spokane Research Center of the U.S. Bureau of Mines, in cooperation with the University of Utah, developed a two-dimensional desktop finite element program, UT2PC, available to the mining community in 1991. This was a short course offered at the 1991 SME Annual Meeting in Denver, CO."

Jan 1, 2017

By Elia Elias, Alan Crosky, Paul Hagan, Damon Vandermaat, Serkan Saydam, Peter H. Craig

"The University of New South Wales (UNSW Australia) had been involved in the study of premature failure of rock bolts in Australian coal mines from the initial identification of the problem in 1999 (Crosky et al 2002). Rock bolt steel changes over the last decade appear to have not reduced the incidence of failures. A broadened UNSW research project funded by the Australian Research Council (ARC) and Industry has targeted finding the environmental causes through extensive field and laboratory experiments. This paper describes the field studies conducted in underground coal mines, in particular attempts to measure the contribution to corrosion from groundwater, mineralogy and microbial activity. Various underground survey techniques were used to determine the extent of broken bolts, with the presence of both stress corrosion cracking (SCC) and localized deep pitting making no single technique suitable on their own. Groundwater found dripping from bolts across various coalfields in Australia were found to be not aggressive and known groundwater corrosivity classification systems did not correlate to where broken bolts were found. In-hole coupon bolts placed in roof strata containing claystone bands confirmed the clay as being a major contributor to corrosion. Microbes capable of contributing to steel corrosion were found to be present in groundwater, and culturing of the microbes taken from in-situ coupon bolts proved that the bacteria was present on the bolt surface. An ‘in-hole bolt corrosion coupon’ development by the project may have multiple benefits of 1) helping quantify newly developed corrosivity classification systems, 2) providing an in-situ ground support corrosion monitoring tool, and 3) for testing possible corrosion protection solutions.introductionThe problem of premature rock bolt failure in Australian coal mines was published in 2002 and 2004 by UNSW Australia from Australian Coal Association Research Program (ACARP) funded projects. The majority of the broken bolts examined had steel Charpy impact toughness values of 4 – 7 Joules, and the failure mechanism was most often stress corrosion cracking (SCC). Steel fracture mechanics predicts that an increase in impact toughness will increase the length of the crack before sudden brittle failure. In the final report of 2004, anecdotal evidence from one coal mine indicated that the problem may be eliminated in some environments by a change to steel grades with higher Charpy impact values of ~16. (Crosky et al, 2002 and 2004)"

Jan 1, 2015

By William G. Pariseau, Michael K. McCarter

"The challenge of estimating mine-wide subsidence and linkages to seismicity over tabular deposits is addressed by a special finite element technique (dual node - dual mesh). Subsidence and mine-induced seismicity begins near the face when caving occurs and propagates to the surface as extraction reaches a critical extent. Thus, the challenge is to obtain details at the face at the meter scale and also at the surface over the whole mine at the kilometer scale. Interactions between old and new sections of a mine are automatically taken into account with this technique. The finite element method is well established technology based on fundamentals of physical laws, kinematics and material laws. With this technique, no empirical ""scaling"" or fitting computer output by input data ""adjustment"" to mine measurements is necessary. Capability is demonstrated for doing practical whole-mine subsidence analysis from first principles. Mine-induced seismicity is shown to correlate well with face advance and element failure.INTRODUCTIONSeismicity associated with coal mining has been under study for several years by a team at the University of Utah. Team members include mining faculty, research geophysicists and students from the Departments of Mining Engineering and Geology & Geophysics. Mines in central Utah that have been studied include the Trail Mountain Mine (Pariseau, 2015; Pariseau and McCarter, 2015), the Beehive Mine, also known as the Des-BeeDove (Pariseau, 2014), and the Crandall Canyon Mine (Pariseau, 2015). These mines were developed from outcrops in the Wasatch Plateau coal field west of Price, Utah, where the topography is characterized by . steeply incised canyon drainages and high plateaus with relief of a thousand meters or so.Seismicity associated with coal mining in central Utah has been of interest for many years and includes studies in the Book Cliffs to the east of Price, Utah, where mining is still active (Smith et al, 1974; Agapito, Goodrich and Moon, 1997; Arabasz et al, 2001; Arabasz et al, 2002; Fletcher and McGarr, 2005; McGarr and Fletcher 2005; Maleki, 2005) and to the northwest (Ellenberger et al, 2001). Results of many micro-seismic studies are summarized perhaps best by lannacchione, et al (2005) in stating, ""Deviations from normal strata response can provide useful stability information.""This study concerns a fourth underground coal mine in the southern portion of the Wasatch Plateau coalfield, hereafter referred to as the MINE. Focus is on mining from 2004-2008 with the objective of examining mining in relation to seismicity."

Jan 1, 2016

By Anthony T. Iannacchione

This study, funded by the Appalachian Research Initiative for Environmental Science (ARIES), examines how mine layout, mining method, and geology interacted to allow water from the Grove No.1 mine pool to discharge into local surface waters. Federal and State regulations prohibit the discharge of acid or iron-producing waters from underground coal mines. Mining companies design barriers around their operations to prevent mine waters from discharging to the surface. The Grove No.1 represents one mine where these designs proved inadequate. Unique geologic conditions at the Grove No.1 mine pool, combined with retreat room-and-pillar mining, contributed to a discharge that required passive water treatment.

Jan 1, 2013

By Mark K. Larson

Panel-scale modeling of stress changes induced by longwall coal mining is a challenging problem, particularly in deep mines of the western United States. Two common approaches to this problem are the empirical and boundary element modeling methods. One boundary element method, LaModel, was recently calibrated to field measurements at a mine in Colorado (Larson and Whyatt, 2012). However, the calibrated overburden properties were extreme, resulting in very low estimates of gob loading. Next, the empirical method was calibrated to field measurements and applied to the problem, but this approach clearly extrapolated this method well beyond the characteristics of underlying cases. This paper examines a third option, the elastic continuum boundary element program Mulsim. The program was expanded to handle LaModel-size meshes in a version dubbed Mulsim/ Large. Properties for the elastic, homogeneous overburden model in Mulsim were estimated as a thickness-weighted average of typical published elastic properties for each major stratum. These properties, along with a commonly used pillar strength equation and coal properties, produced the measured load transfer distance and reasonable gob loading without further calibration. Given the number of input parameters required for all of these methods, it is not surprising that LaModel and the empirical approach could be adjusted further to incorporate similar gob loads. However, these extraordinary measures failed to bring gate road pillar loading in line with Mulsim results. Differences in pillar load estimates continued to be significant (as large as 65% in this study). These results demonstrate that, for this particular case, the choice of analysis method impacts results in ways that cannot be removed by calibration of input parameters. Finally, the natural fit between the Mulsim model and mine conditions suggests that approximating overburden at the particular site used for this research as an elastic continuum is superior to the alternatives examined.

Jan 1, 2013

By Lightfoot. Nicholas, Na Liu

"Mining in multi-seam workings has been undertaken for many years in the VK Remnant pillars above and/or below current working areas have an important influence on retreat gateroad conditions at five of the remaining six deep coal mines. These interaction effects need lo be predicted ahead of mining so that longwall panels can be positioned to minimize roadway damage and to identify areas where additional support should be installed early into competent strata when and where it is most effective.Currently, three-dimensional elastic stress analysis using MAP3D is undertaken to predict local vertical and horizontal stress magnitudes during gateroad development and in front of the face on retreat. The predicted stress fields are often used as input to FLAC for roadway modelling.Using Maltby Colliery in South Yorkshire as a case study, this paper illustrates the MAP3D approach, together with its current limitations and uncertainties. Possible future improvements in the analysis method are proposed and the authors would welcome comments on these, or suggestions for alternative approaches.MODELLING OF MULTl-SEAM LAYOUT & MULTI-SEAM INTERACTIONThe remaining large coal mines in the UK arc operating at depths of 800-1, 150 m (2,625-3,773 ft). Production panels are now mined on retreat after the accompanying single entry access roadways have been completed. These gateroads are typically supported with a system of steel rock bolts and cable in the roof and steel bolts and glass re in forced polymer (G RP) dowels in the sidewalls.In addition to new panels being mined in the vicinity of old goafed districts, a significant amount of extraction has usually already taken place in coal seams above and/or below the current working areas. This means that there is also interaction between the current workings and the remnants of the old workings in other seams. As a consequence of the mining methods employed, old workings can have a complex geometry compri ing collapsed and partially collapsed excavations intersper ed with small and large pillars of unmined coal. The unmined coal pillar act as stress concentrators that carry the overburden load while the mined out excavations create stress shadows of varying degrees depending on how much collap e and reconsolidat ion has occurred. This is illustrated by a simple elastic model as shown in Figure I."

Jan 1, 2010

By Gang Ren, Behrooz Ghabraie

"Observational data suggest that the ground surface subsidence profile from multiple-seam longwall mining is rather different from that of single seam. Despite the increase of coal production from multiple-seam mining, available predictive methods are mostly unable to predict a reliable subsidence profile for multiple-seam extractions. In this paper, a case study of multiple-seam subsidence is modelled using physical modelling techniques. The subsidence mechanism as revealed in the physical model is explained and the differences between multiple and single-seam subsidence are highlighted. On the same case study, a commonly used influence function method (IFM) and Generalised Influence Function Method (GIFM) are utilised to predict the subsidence profile. The results are compared with predictions achieved by a newly developed predictive method based on the understanding of mechanism of the multiple-seam subsidence. Results show a significantly improved correlation between the newly developed method in comparison with the conventional IFM and GIFM. INTRODUCTIONField observations and subsidence monitoring data from multiple-seam coal mining cases show a different subsidence profile as compared with single-seam ones (Sheorey et al., 2000; Li, et al, 2007; Luo and Qiu, 2012; Unlu et al, 2013). The multiple-seam subsidence curve is generally deeper and steeper than of single-seam cases, and varies from one mining configuration to another. Various researchers had made efforts to understand the mechanism behind this phenomenon and the interaction between the two mining horizons (Li et al., 2010, Sui et al., 2014; Zhang et al., 2014). However, the mechanism of the multiple-seam subsidence is yet to be comprehensively understood (Suchowerska, 2014; Ghabraie et al., 2015b).In addition, differences between the single and multiple-seam subsidence profiles make it difficult to adapt single-seam subsidence prediction tools for predicting the subsidence over multiple-seam cases, unless significant modifications are applied This requires understanding the mechanism of the multiple-seam subsidence as the first step to achieve reliable predictive results.The mechanism of the subsidence due to a multiple-seam case study can be investigated via physical modelling. The physical model allows observing the substrata movement as well as the interaction of the two mining activities. An understanding of the mechanism of the multiple-seam subsidence can be developed based on these observations, which would provide basis for developing a subsidence prediction tool."

Jan 1, 2016

By Zbigniew Lubosik, Andrzej Walentek, Stanislaw Prusek, Aleksander Wrana

"The Carboniferous coal measures, mined across Europe including the major European underground coal mining countries of Poland, UK, Germany, and Czech Republic, suffer from increasing extraction depth. This results in major geomechanics problems associated with ground control and support design.With production being concentrated into ever fewer high performance longwalls, located at greater and greater depth, pressure to ensure the roadways’ functionality (required dimensions) continues to increase. Mining in deeper and more highly stressed mining environments creates several problems. The high stress and deterioration in geological and mining conditions in many cases causes problems with gateroads maintenance (due to excess convergence). That leads to costly production gaps, longwall slowing, transport problems, an increase in the methane hazard and in the general health and safety of the workforce, and deterioration in climatic conditions with major economic risk associated with interruption of the revenue stream. Time—and thus production—delays due to maintenance often result from insufficient geological and geotechnical data acquisition and misinterpretation combined with inadequate support for the type of rock mass.longwall face on the gateroad stability (described by the gateroad convergence, support load, and shape and height of the fractured zone around the longwall gateroad) are presented. The investigations were carried out in the longwall panel with roof caving located at the great depth, in conditions of the Upper Silesian Coal Basin in Poland.The measurement results showed that the gateroad fractures in roof strata began to occur at the distance of about 1000 m ahead of the face. Additionally, the load on support and gateroad convergence increased as the longwall face got closer.It is very important for coal mining research institutes and mine operators to investigate and develop practical solutions and apply innovative support technologies at a great depth (particularly for reinforcement and stabilization of roadways and other openings).Underground measurements of stability conditions around the gateroad is of great importance to mining practice, especially in planning and designing supports for longwall gateroads.The influence of the front abutment pressure results in an increase of support load, gateroad convergence, and shape of fractured rock zone."

Jan 1, 2015

By Bo-Hyun Kim, Mark K. Larson

"While faults are commonly simulated as a single planar or non-planar interface for a safety or stability analysis in underground mining excavation, the real 3D structure of a fault is often very complex with different branches that reactivate at different times. Furthermore, these branches are zones of non-zero thickness where material continuously undergoes damage even during interseismic periods. In this study, the initiation and the initial evolution of a strike-slip fault was modeled using the FLAC3D™ software program. The initial and boundary conditions are simplified and mimic the Riedel shear experiment and the constitutive model in the literature. The FLAC3D model successfully replicates and creates the 3D fault zone as a strike-slip type structure in the entire thickness of the model. The strike-slip fault structure and normal displacement result in the formation of valleys in the model. Three panels of a longwall excavation are virtually placed and excavated beneath a main valley. The characteristics of stored and dissipated energy associated with the panel excavations are examined and observed at different stages of shear strain in the fault to evaluate bump potential. Depending on the shear strain in the fault, the energy characteristics adjacent to the longwall panels present different degrees of bump potential, which is not possible to capture by conventional fault simulation using an interface.INTRODUCTIONThis paper is part of an effort by the National Institute for Occupational Safety and Health (NIOSH) to identify risk factors associated with bump-prone potential in highly stressed ground conditions. More specifically, this paper reports an exploratory effort with an unconventional approach using a numerical tool to try to better understand a possible scenario where bump risk might be increased—that is, a scenario involving a strike-slip fault. The objective is to assess whether a numerical tool might be useful or practical in forecasting bump potential associated with a strike-slip fault for a typical, structural geologic setting."

Jan 1, 2018

By David F. Gearhart, Mark Van Dyke, Heather Dougherty, Ted Klemetti, Gabriel S. Esterhuizen

"Coal mine longwall gateroads are subject to changing loading conditions induced by the advancing longwall face. The ground response and support requirements are closely related to the magnitude and orientation of the stress changes, as well as the local geology. This paper presents the monitoring results of gateroad response and support performance at two longwall mines at a 600-ft and 2,000-ft depth of cover. At the first mine, a three-entry gateroad layout was used. The second mine used a four-entry, yield-abutment-yield gateroad pillar system. Local ground deformation and support response were monitored at both sites. The monitoring period started during the development stage and continued during first panel retreat and up to second panel retreat. The two data sets were used to compare the response of the entries in two very different geotechnical settings and different gateroad layouts. The monitoring results were used to validate numerical models that simulate the loading conditions and entry response for these widely differing conditions. The validated models were used to compare the load path and ground response at the two mines. This paper demonstrates the potential for numerical models to assist mine engineers in optimizing longwall layouts and gateroad support systems.INTRODUCTIONThe need for roof stability in coal mine longwall gateroads places significant demands on the gateroad ground support system. The variable loading conditions associated with the approaching longwall face can cause excessive ground deformations that need to be accommodated by the support system. In coal mines in the United States several different types of supports are used to maintain the stability of gateroads. The supports may include grouted roof bolts, cable bolts, and roof trusses as intrinsic support. Standing supports include timber cribs, engineered timber props, and various types of cement-based cribs. The intensity of support is governed by the expected geologic conditions and the expected stress changes that will occur during longwall mining. At present, the design of ground support for gateroads is largely based on local experience. In-mine trials are usually conducted when new support technologies become available or ground conditions dictate a change in the support system. The research reported in this paper has the objective to assist mining engineers in evaluating alternative gateroad supports and to design suitable support systems for the local ground conditions."

Jan 1, 2018

By Shuren Wang, Wenbing Guo, Paul C. Hagan, Yanhai Zhao

"The overlying strata is often destroyed in large scale during shallow coal seam mining, and the sliding instability of the caved roof seriously threatens the safety of the mining field. The typical shallow coal mining in Shendong Mining Area in China was used as engineering background; the load distribution characteristics of the overlying strata were analyzed based on the monitoring data of the support resistance. Through theoretical analysis and numerical simulation, the formation and changing process of the pressure-arch in the overlying strata were studied, and the instability mechanism of the overlying strata was revealed by focusing on the accumulation and release law of the elastic energy in the pressure-arch. The results show that the continuous pressure-arch was formed when the horizontal stress exceeded the primary vertical stress of the mining field, and the elastic energy of the roof was released by the mining unloading effect. The elastic energy was accumulated in the pressure-arch, and the energy arrived the highest at the front arch foot. The accumulated energy at the arch foot was released by coal mining, and the shear zone could be formed. Therefore, the sliding of the caved zone along the shear zone induced strong roof weighting. The concentrated stress and the released energy during each mining increased with the panel advancing, and the height of the shear zone also increased. The conclusions obtained in the study are of important theoretical value to direct similar engineering practice.INTRODUCTIONThe instability of overlying strata during shallow coal mining, such as the large-scale roof falling and step-like ground subsidence, is a key problem that can restrict the safety mining in the mines (Ju and Xu, 2015). The self-bearing structure of the pressure-arch can form in the overlying strata after coal mining, and this structure can support the load of the upper strata and soil layer, so the weighting intensity of the panel is determined by the caved rock in the unloading zone under the inner boundary of the pressure-arch. A large amount of elastic energy is accumulated in the pressure-arch under the concentrated stress, and the released energy for mining is the internal cause of rock failure (Wang et al., 2017). It is an important problem to reveal the distribution characteristics of the stress and energy fields in the mine and to analyze the stability of the overlying strata during shallow coal mining based on the evolution characteristics of the pressure-arch."

Jan 1, 2018

By Francis S. Kendorski

Rock reinforcement has been in widespread use and generally has been accepted in underground mining and tunneling since the 1950s. The first rock reinforcement technologies employed were mechanical anchors such as split wedges or expansion shells with 5/8-inch-diameter steel bolts. Failures occurred in weak strata which provided poor anchorage or in ground with corrosive waters. Friction rock fixtures consisting of relatively thin-walled tubes have been in use for about 15 to 20 years. While generally performing adequately, longevity problems have developed from corrosion in water bearing ground Longevity of rock reinforcement is much enhanced with grouted bolts. Portland-cement-grouted rock reinforcement has been in use since the mid-1950s, primarily in funneling and other civil engineering underground construction. Tests of decades-old installations have revealed few problems except in ground with aggressive waters. Polyester-resin-grouted rock reinforcement was introduced in the United states to musing in the late 1960s and to tunneling in the early 1970s. Experience from 30 years of resin-grouted bolt installations and field tests have identified longevity problems associated with degradation of steel reinforcing bars, but in generally unusual situations. Improvements continue in resin chemistries, packaging, corrosion protection, grout quantities, and mixing and distribution in the drilled hole to achieve long-term performance. Specific case histories cited with resin- or Portland-cement-grouted rock reinforcement longevity or performance problems, upon close examination, reveal that the causes of the problems were qualify control procedures being inadequate and not in accordance with good practice. Manufacturers' recommendations and engineering specifications, if followed in the field, and with competent inspection and supervision, would have prevented must, if not all, reported longevity or performance difficulties.

Jan 1, 2000

Results of direct shear tests on rock discontinuities and triaxial compression tests on intact rocks are presented and - discussed. The main parameters considered area stress functions, angle of internal friction and cohesion variations. Primary objective of this work is to determine relationships that adequately describe the rock behaviour for design of mining excavations, while still maintaining a certain degree of simplicity.

Jan 1, 1987

By Kot Unrug

For the purposes of underground mine design, twelve cores of the Springfield (V) Coal (Pennsylvanian) roof and floor were retrieved. Each core was photographed, described fresh in the barrel, and the rock quality designation (RQD) was measured. Cores were wrapped in plastic and delivered to the rock mechanics lab. At the lab RQD was remeasured and new photographs were taken before running geotechnical tests including weatherability. Significant differences in barrel RQD's vs. lab RQD's have been noticed in spite of careful handling. The drill site RQD is generally used to calculate geotechnical results, but in some types of coal measure rocks, further fragmentation of core takes place with slight changes of moisture content, which occur even in well wrapped core. This creates a dilemma which RQD should be used for support design. Rocks around excavations are exposed to the significant changes in moisture content due to the seasonal weather changes and related fluctuation of humidity of air ventilating a mine. Therefore, it appears to be more realistic using laboratory RQD which corresponds closer to the actual rock condition around the excavation. Weatherability test, developed for characterization of time dependent behavior of rock exposed to fluctuations in moisture content, is thought to be related to the above-mentioned changes of RQD. In weak shales, mudstones and claystones which weather rapidly, it is essential to characterize their future behavior in the pre-mining stage. This can allow for a realistic design of primary, and particularly secondary support in coal mines, especially in coal fields where such geologic conditions exist.

Jan 1, 2003

By Khaled M. Mohamed, Michael M. Murphy, Ted M. Klemetti, Heather E. Lawson

"The design of rib support systems in U.S. coal mines is based primarily on local practices and experience. A better understanding of current rib support practices in U.S. coal mines is crucial for developing a sound engineering rib support design tool.The objective of this paper is to analyze the current practices of rib control in US coal mines. Twenty (20) underground coal mines were studied representing various coal basins, coal seams, geology, loading conditions, and rib control strategies.The key findings are: (1) any rib design guideline or tool should take into account external rib support as well as internal bolting; (2) rib bolts on their own cannot contain rib spall, especially in soft ribs subjected to significant load—external rib control devices such as mesh are required in such cases to contain rib sloughing; (3) the majority of the studied mines follow the overburden depth and entry height thresholds recommended by the Program Information Bulletin (PIB) 11-29; (4) potential rib instability occurred when certain geological features prevailed—these include draw slate and/or bone coal near the rib/roof line, claystone partings, and soft coal bench overlain by rock strata; (5) 47% of the studied rib spall was classified as blocky—this could indicate a high potential of rib hazards; and (6) rib injury rates of the studied mines for the last three years emphasize the need for more rib control management for mines operating at overburden depths between 500 ft and 1,000 ft.IntroductionEfforts to improve the stability of underground mine ribs have continued for decades. These efforts by mining professionals around the world persisted throughout the 1990s and 2000s as well, though much of this work focused on rib support methodology and selection of proper support for a specific location. Despite these efforts, it is unfortunate that there has been a continual occurrence of rib-related fatalities in underground coal mines. While overall improvements in rib safety have been achieved, the average fatality rate is still about 1.3 fatalities per year over the last 18 years (Jones, 2014).To manage and control the rib hazard, rib support is used in U.S. coal mines. The current rib support methods for U.S. mines fall into two main categories: rib control based on intrinsic support systems and those based on external support systems. Intrinsic or rib-bolt support requires a roof bolting machine that can install a bolt fixture into the rib. Furthermore, the appropriate level of support needed to control the ribs with an intrinsic-based support system as well as the design parameters for those support systems for various mine conditions have not been established in U.S. coal mines. Furthermore, surface control systems are often an integral part of these support systems and must be considered in the system design."

Jan 1, 2015

By Xingkai Wang, Wenbing Xie

"To control the large deformation of soft rock around the roadway subjected to high stress, it is important to improve the stability of support structure, in addition to increasing support strength. In this study, the causes for the destabilization of U-steel frame and its loading characteristics were analyzed by theoretical analysis, laboratory experiments and field tests. The technology of constant support resistance, the principle of support structure compensation and the compensation technique are proposed. The results indicated that the main reasons for frame structure destabilization are caused by low strength of connector, irrational structure of connector, poor interaction between the surrounding rocks and support frame and structure, and unstable support structure. Thus, the corresponding technological measures, such as connector with high strength and rational structure are adopted. The bearing capacity of frame is unstable after slipping. In order to maintain the high support resistance when the frame is performing the support function, the frame connector should be retightened after slipping. Though the working resistance may be improved greatly by using the backfilling or back grouting of U-steel, the frame remains unstable because of the unstable frame structure. Therefore, according to the deformation characteristics of rocks surrounding the roadway and the structure instability of U- steel frame, the stable structure device is used to carry out the structural compensation of U-steel frame, and the whole bearing capacity of the frame and its structural stability are improved greatly.INTRODUCTIONThroughout the development of the roadway supports for coal mines in China, it can be seen that the supporting strength and supporting resistance increase continuously with increase in mining depth and supporting difficulties [1]. With respect to the ground control mechanism and supporting technology of rocks surrounding the soft rock roadways subjected to high stress, considerable research has been done both at home and abroad. The backfilling technology behind the high-resistance and yieldable U-steel wall, the new type of grout/bolt support technology and the bolting with high-strength mesh support technology were developed, and have been used widely in coal mines with notable economic benefits [2-7]. However, a large number of engineering practices show that in many cases the existing rock control technology of roadway may not control the large deformation of the soft rock roadways subjected to high stress. The reason that the large deformation of soft rock roadway occurs is mainly due to poor structure stability of existing frame bearing structure, not insufficient support strength."

Jan 1, 2015