Search Documents

By G. R. Giuliani

Hanna Mining Company's Groveland Mine is located in the Upper Peninsula of Michigan. The low grade iron ore deposit consists of a mixture of magnetite and hematite with chert, jasper, quartz and various iron silicates (1). The ore is beneficiated by magnetic separation and anionic flotation of the iron minerals with chemical depression of the silica. The magnetic concentrate makes up about 75% of the concentrate. The concentrate is pelletized at the rate of 2.0 million LTPY of pellet production. The concentrator facilities were started up in 1959 and the concentrate was marketed as sinter feed until 1963 when the concentrator was expanded and the pelletizing plant was added. The pellet plant now consists of regrinding, elutriation, filtering, balling and induration. The pellet machine is a straight grate which employs updraft drying and cooling and downdraft drying, preheat and firing. It is necessary to regrind the concentrate before pelletizing. The con-centrate is 60% passing 325 mesh, with a surface area of ±lOOO cm2/Gm, and must be ground to about 83% passing 325 mesh, 1600 cm2/Gm blaine surface area, for pelletizing. The energy for regrind has been reduced from 12.5 KW per LT to 8.80 KW ate of 2.0 million per LT. This was the result of changes made in the concentrator where originally a coarse spiral concentrate, instead of the magnetic concentrate which is screened on fine screens to reduce the coarse fraction and prevent overgrinding before flotation, was produced. Also in 1968 an additional concentrating line was added to the concentrator which employs more grinding power than the other three lines. The demand for a high iron grade and lower silica pellet resulted in the investigation of different schemes of upgrading the reground concentrate which had more iron values liberated during grinding for surface area. The reagentized material presented many problems, mainly in selectivity trying to flot the iron and with high reagent consumption having to dereagentize the concentrate for amine silica flotation, in the various flotation systems tried. Tests were then conducted with elutriation (2) which proved satisfactory by removing the lower specific gravity, fine gangue material from the heavier material with the

Jan 1, 1977

By C. A. Rawlins, P. Rostami

"Ventilation systems are not only an integral part of any underground mine design but are a significant contributor to the mine’s capital and operating costs. The ventilation and cooling design systems presented in this paper were part of the prefeasibility evaluation of an underground platinum mine in South Africa. The mine would ultimately operate at the depth of 1,200 m below surface with a proposed 4 Mtpa production rate. The proposed mining operation is a highly mechanized operation using diesel equipment. Significant daily production rate, large amount of equipment and expansive nature of the operation, contributed to a challenging while flexible ventilation design requirements. This paper presents how to safely and efficiently optimize capital expenditure and operating costs associated with the mine air cooling and refrigeration system through practical ventilation design practices. Successful capital and operational savings by modulating installation and commissioning of refrigeration facilities can influence the economic realization of such systems. The adapted planning and design approach provided a cost-effective advantage while complying with design safety and regulations. INTRODUCTION This paper outlines a prefeasibility evaluation of the heat loads and related cooling system to be employed at the proposed platinum mine. The paper also provides appropriate details for a comprehensive understanding of the applied methodology. The proposed mine will be a trackless underground operation using a combination of mining methods. Initially, ore zones with vertical thicknesses greater than or equal to 18 m will be mined using the long-hole stoping (LHS) method, while thinner ore zones will be mined using mechanized drift-and-fill or drift-and-bench methods; hence, a highly mechanized operation with LHDs, trucks, drill rigs, personnel carriers, etc. is envisioned. Broken rock (ore and waste) will be transported by the means of trucks to the main passes (ore and waste) and collection points. Mining zones identified in the project occur at depths ranging between approximately 700 m to 1,600 m below surface. Primary access to the mine will be via a 1,100 m deep, 10 m diameter production shaft (named Shaft No. 2), three additional shafts will be sunk to provide future ventilation and production support. Three main access levels are established as primary haulage levels and include a series of interconnecting ramps. Additional mining sublevels will be developed as necessary. Figure 1 shows the proposed shaft locations and main access levels in a 3-D elevated view. Mining is performed using highly productive mechanized methods. For this reason, an annual ventilation estimate is based on requirements for mobile equipment (i.e., 0.06 m3/s/kW). The air requirements imposed on the underground operation is further influenced by equipment heat loads, auto compression, and virgin rock temperature, as the main sources of in-mine heat."

Jan 1, 2015

By Libby R. Ricafort, Nonato S. Retardo, Jose B. Anievas

This paper shows the metallurgical test results that led to the design of the heap leach facilities of Philex Mining Corporation. The design incorporates a water management model as process solution circulation is excessive with high rainfall intensity in the area. This poses problems in the operations requiring stringent controls than would be necessary in a less severe environment. The corporate perspective embraces on environmentally-sound mineral development. A budget is always provided to environmental management making certain that no industrial development is moved forward at the expense of the environment.

Jan 1, 1996

By C. J. Johnson, C. J. Bise

Abstract - As the US coal industry moves into the next century, it is becoming more apparent that the effective application of new technology is the only way it can remain competitive in the energy marketplace. Examples of this emphasis are with us today in such diverse areas as face- ventilation and excavation-equipment applications. The focus of this new technology is directed toward improvements in health and safety, cost control, and productivity. Room-and-pillar mining accounts for approximately 68% of the nation's underground coal production; this percentage is not expected to decrease markedly in the near future. As such, this paper analyzes the impacts of the changing techno- logical climate on future room-and-pillar operations by comparing a base-case section (current) to three scenarios incorporating new or emerging technology. A microcomputer-based comparative analysis will reflect the changes in section production and costs.

Jan 1, 1990

By J. A. Jirestig

Laboratory investigations on the possibility for magnetic separation of sulphide minerals are reported. A survey of several sulphide ores and flotation concentrates shows that magnetic separation in most cases is not a suitable primary method of beneficiation. However encouraging results have been obtained in concentrate purification. At the Boliden complex sulphide ore concentrator in Garpenberg a Allis-SALA MK III carousel High Gradient Magnetic Separator (HGMS) is used together with a small flotation circuit to recover sphalerite lost to the galena concentrate in lead flotation. The result after four years of refining the HGMS process, show increasing zinc recovery and enhanced quality of the lead concentrate.

Jan 1, 1993

By David A. Summers

In May 1975 the U. S. Bureau of Mines contracted with the University of Missouri-Rolla, Rock Mechanics and Explosives Research Center to develop a Hydrominer modification to a long-wall shearer unit, wherein the rotating pick-laced drums and connecting gear drives are replaced by a water jet cutting head.1 The concept of the water jet cutting head is based on using the high localized energy of the water jets to isolate a slice of coal by cutting a slot under, at the back of, and at the top of the web. The plow blade of the head then advances into the cut and wedges the pillar over onto the conveyor (Figure 1). There were several potential advantages foreseen for the system of which perhaps the most significant were the elimination of coal dust from the working area2 and the ability, with a variation in nozzle geometry, to cut webs of greater depth with a small increase in equipment horsepower. The University initially designed the head, based on experiments carried out in the laboratory, under an earlier Bureau of mines contract. The experiments showed that it was more advantageous to work at a pressure of 10,000 psi with an estimated flow rate of 50 gpm than go to the higher pressures and lower flow rates which have been advocated elsewhere.

Jan 1, 1977

By R. B. Elver

The level of steel consumption per capita is one of the principal indicators of a country's standard of living. It is no coincidence that the materially advanced nations possess viable iron and steel industries to provide a reliable and economic source of steal for the manufacturing industries. No other metal is as dominantly important in manufacturing as steel. The blast furnace - steel furnace complex based on coking coal, ferrous scrap and iron ore - continues to be the principal steel-producing method. Less important is the electric furnace method based on scrap, In recent years, there has been considerable interest in the many direct reduction processes that are not dependent on coking coal but usually produce a product for further refining in steel furnaces. No matter which series of processes are used, iron ore is essentially the only source of virgin iron units. Thus, to such a vital and capital-intense industry as steel, access to a relatively inexpensive, long- term supply of iron ore is essential.

Jan 1, 1964

By D. H. White

The term "block caving" as used in this text includes panel caving and mass caving as described by Julin and Tobie (1973). This method reportedly was conceived in 1895 when a block of ore ranging up to 200 ft (61 m) in width was undercut at the Pewabic Mine on the Menominee Range in Michigan (Bucky, 1956). Over the years this method has evolved largely as a consequence of trial and error in which operators became acutely aware of what nature would allow and what it would not. Today block caving remains somewhat of an art rather than a science where experience often dictates what needs to be done. With the plunging prices of base and specialty metals in the early 1980s caving mines sought to reduce operating and development costs in order to return to profitability. For some this became an impossible task given the design, grade and operating costs of the day and closure became the only alternative. One lesson learned from the experiences of the 80s is that survivability depends on cost competitiveness and this implies the efficient use of resources and technology. To this end applied rock mechanics serves as a useful tool. The purpose of this paper is to show how Geomechanics can be used? in block caving to facilitate sound decision making and how this equates to dollars saved. Features of mining method selection, design and operation are discussed as related to this theme.

Jan 1, 1990

By W. R. Reed, D. E. Pollock, T. W. Beck, J. A. Organiscak, J. D. Potts

"In underground continuous mining operations, ventilation, water sprays, and machine-mounted flooded bed scrubbers are the primary means of controlling respirable dust exposures at the working face. Changes in mining arrangements, such as, face ventilation configuration, orientation of crosscuts mined in relation to the section ventilation, and equipment operator positioning, can impact the ability of dust controls to reduce occupational respirable dust exposures. This study reports and analyzes dust concentrations measured by the Office of Mine Safety and Health Research for both remote-controlled continuous mining machine operators and haulage operators at ten U.S. underground mines. Results of these respirable dust surveys show that continuous miner exposures varied little based on depth of cut, but are significantly affected by ventilation configuration. Haulage operators experienced elevated concentrations in blowing face ventilation. The type of cut influenced exposures, with elevated exposures observed for both continuous miner operators and haulage operators when working in crosscuts driven into, or counter to, the section airflow. Individual cuts are highlighted to demonstrate instances of minimal and excessive dust exposure attributable to particular mining configurations. These findings form the basis of recommendations for lowering face worker respirable dust exposures when performing a variety of continuous mining cuts.INTRODUCTION Underground continuous coal mining operations may encounter a wide range of conditions and arrangements during production and development activities. These activities typically produce respirable coal mine dust, putting operators of continuous mining machines and coal haulers at risk for elevated exposures. In order to comply with federal regulations limiting respirable dust exposures for the duration of a working shift, mine operators typically implement ventilation, water sprays, and machine-mounted flooded-bed dust collectors (scrubbers) to dilute and control mine dusts during coal cutting. Nevertheless, changes in operational conditions can limit the ability of these controls to effectively reduce dust exposures. Some examples of conditions that can change during the course of mining include face ventilation configuration, orientation of crosscuts mined in relation to the section ventilation, and operator positioning. Because these arrangements are largely under the control of mine operators, any insight into associated exposures may inform future plans and behaviors, reducing occupational exposures to respirable dust. The objective of this OMSHR study is to evaluate respirable dust exposures associated with a range of continuous mining arrangements by comparing occupational dust concentrations measured during a series of field surveys. These comparisons consider face ventilation configurations, depths of cut, and crosscut mining practices."

Jan 1, 2015

By J. J. Kellar

The near-infrared (NIR) (12,000-4,000 cm-1) region of the electromagnetic spectrum, between the mid-infrared and visible, has often been viewed by spectroscopists to be of limited utility. This is unfortunate, and recently the use of the NIR has increased greatly, primarily for the quantitative analysis of food and agricultural products. However, many other areas of application of NIR spectroscopy remain unexamined. In this paper a novel use of NIR in the area of flotation chemistry is demonstrated. Specifically, it is shown that NIR/Internal Reflection Spectroscopy (IRS) can be used to quantify collector adsorption reactions in-situ.

Jan 1, 1990

By R. E. Ray

As coal reserves at shallow depths continue to be exhausted, a number of US coal companies are developing seams previously considered too deep to mine economically. Because of increased cover load, mines operating in deeper seams face unique ground control problems. In addition, the volume of methane gas in coal beds increases with depth, and ventilation requirements are much more stringent for deep mines than for shallower mines. When the longwall mining method is wed at great depths, ventilation, ground control, and operational considerations all influence the design of longwall panels. This paper examines these influences, particularly ventilation and operational considerations, on the feasibility of two-, three-, and four-entry longwall development panels in Jim Walter Resources' four deep mines.

Jan 1, 1988

By James J. Komadina

INTRODUCTION Newmont Gold Company's Rain operations are located in Elko County, Nevada, approximately 9 miles southeast of the Town of Carlin.The property was submitted to Newmont Exploration Limited in 1979 and underwent development drilling over the course of the next four years, culminating in the completion of a project feasibility study in October 1986. Initial project scope included development of an open pit mine, an 815,000 DSTPY heap leach, a 572,000 DSTPY mill (Mill No. 3), and associated support facilities. Approval to proceed was given by Newmont Gold Company management in June 1987. Detailed engineering began in early July, followed immediately thereafter by procurement of major equipment components through various second hand sources. PROJECT DESIGN Keep It Simple In early August, Newmont Mining Corporation, parent company of Newmont Gold Company, became the takeover target of an "investor" group headed by T. Boone Pickens. Details of the ensuing events have been well documented by the press; suffice to say their impact on this project was material and required immediate flowsheet changes. Project design throughputs were increased to 1,000,000 DSTPY and 760,000 DSTPY for the heap leach and mill, respectively, in mid- September. These changes caused major project headaches as all general arrangement drawings had been approved and structural steel as well as concrete contracts were in place. Additionally, ground breaking was to commence in two weeks time! Rain project management assembled shortly after the announced changes, to devise an engineering and construction strategy capable of handling these new business conditions. The project had been justified using a gold price of $325 per ounce with a forecasted overall cash cost per ounce of $230. Hence, strict control of capital expenditures was necessary to maintain development economics. Mill start-up had also been moved forward one month, to August 1, 1988. To meet an already ambitious schedule, construction techniques needed to be simple and proven as most of the facilities were planned for erection during winter at a site with design criteria of -40F and 90 mile per hour winds. Perhaps the most critical factor requiring consideration was that of personnel. Newmont Gold's revised business plan called for corporate-wide production increases from 587,000 ounces per year in 1987, to 1,400,000 ounces by mid- 1989. Labor requirements were forecasted to grow from 900 employees to over 2,100. This fact, in combination with the rapid growth of Nevada's gold industry, led to the expectation that turnover of operating personnel would be extremely high. It was concluded that, to meet cost, time, and operational goals, the necessary strategy could be succinctly put - "Keep It Simple." Mining/Metallurgical Factors The Rain deposit consists of three interconnecting mineable shapes with host rocks ranging from 90%+ barite to a highly silicified jasperoid. Due to a limited number of mining faces in the first two years, in-pit blending

Jan 1, 1990

By J. R. Riding

In situ solution mining of uranium has environ- mental advantages over conventional mining. The leaching of uranium, however, alters the groundwater quality in the aquifer where the mining occurs. Currently, regulations require that the groundwater be restored to approximately its original condition. This paper, a summary of a study funded by the Bureau of Mines, reviews the state of the art in restoring groundwater quality after in situ uranium leaching. Current restoration practices discussed include disposal of liquid wastes in deep disposal wells and evaporation ponds, producing from all wells during restoration, and recirculating water purified in surface plants. Methods for predicting the effectiveness and cost of current techniques are presented. Possible alternative techniques are also described. Two restoration operations are discussed.

Jan 1, 1979

By M. Dondi, M. Surracco, G. Alfano, P. Saba

Recent investigations on fine grinding with jet mill miprototypes of original design, constructed at the DIMM and Centro Studi of the National Research Council at Cagliari University, have led to the realization of a third generation micronizer characterized by large capacity and high efficiency. The new model and its distinctive features are described here and the results are presented of grinding tests on typical, high grade Sardinian minerals used for quality products. The operating principles of the jet mill are described in relation to the mechanico-elastic properties of the minerals treated. In particular the efficacy of the comminution process is demonstrated in terms of both solid treated and of impact, attrition and shearing forces generated in the micronizer. Particle size distribution of the finished products are reported, that satisfy the most stringent market specifications for the different minerals, as well as energy consumptions. The alternative operating options for solving particular grinding problems and minimizing energy consumption are discussed. Lastly, the main developments of the jet mill for a possible application at industrial scale are suggested.

Jan 1, 1995

By P. R. Taylor

Three refractory gold concentrates have been tested to evaluate the effect of roasting with hydrated lime followed by cyanidation. The results indicate that it may be possible to roast in such a manner as to contain nearly all of the sulfur, arsenic and antimony in the roaster calcine. Cyanidation results indicate that the gold recoveries are greater than 80% for all three concentrates.

Jan 1, 1993

By H. Colijn

Belt conveyors have proven themselves for many years as a dependable and low cost method of handling bulk materials at high flow rates. The success of a belt conveyor system greatly depends on the initial loading of the material on the belt. If the material is loaded on the belt at the center, at approximately the same speed and with minimum impact, then most of all belt conveyor problems disappear. Proper belt loading is primarily determined by the engineering and design of the conveyor transfer point. This paper will establish and discuss some general design criteria required for proper loading and transfer of materials from one conveyor to another. Specific attention is given to loading points, chutes, skirt board length and general design of transfer structures.

Jan 1, 1971

By Rudolph H. Jacobson

The leaching of heaps or sub-marginal waste ore dumps as it is practiced throughout the Southwest as well as other parts of the world, is the major method of secondary recovery of copper. In 1970, twenty percent of all domestic copper was produced by dump leaching operations (l). In recent years, this method has been successfully extended on a limited scale, for the recovery of uranium from low-grade ores (2). It is inevitable that this technique will be increasingly employed in metal production to satisfy the insatiable demand of our mineral based society. Although dump and heap leaching has been used effectively for some time (3) , its application has been more of an art than a science. Therefore, it is essential that we learn about the important factors and parameters affecting this versatile process so that we may make increasing use of this technique in the future. The dump or heap leaching process encompasses the preparation of ore for-subsequent inplace leaching, the flow of solutions and ionic species through porous rock masses, the leaching of minerals with inexpensive and, if possible, regenerable lixiviants under prevailing conditions of the inplace environment, and the recovery of metals from the pregnant liquors. It is evident that this comprehensive scope of dump or heap leaching falls under the realm of interdisciplinary science and engineering requiring the application of the principles of physics, mineral engineering, hydrology, computer modeling, operations research, economics, and allied disciplines. An exhaustive study of the phenomenology of a leach dump or heap requires detailed knowledge of the simultaneous interaction of'

Jan 1, 1972

By P. Somasundaran

Flotation of oxide minerals is controlled by a number of factors, such as surface potential and solubility of the mineral, concentration and type of various inorganics, properties of the collector, pH, ionic strength and temperature. The role these factors play depends on the mechanisms of adsorption of the collector inorganics or polymer additives. The major mechanisms include electrostatic interactions, chemical adsorption, chain-chain interaction between adsorbed collector species and modifications of the surface by inorganics. In real systems, flotation is, however, markedly affected by various other processes, including aging of the minerals, surface precipitation of the collector on the mineral and associative interactions between various collector species leading to highly surface active, for example, ionomolecular complexes. These effects are reviewed here with selected examples.

Jan 1, 1999

By Z. Abdel-Khalek, Hassan El-Shall, S. Farrah, C. Boice

Selective adsorption and surface modification of minerals by surfactants is the primary step in the process of separating certain minerals with similar physical and chemical characteristics in the flotation process. In this study, microorgan- isms are used as surface modifiers for francolite and dolomite. Results of adsorption experiments with francolite and dolomite show that the microbes selectively adsorb to one of the minerals under specific operating conditions. In preliminary flotation experiments, it is found that the microorganisms enhance or depress flotation of the minerals leading to an increase in the efficiency of separation between the francolite and dolomite. The conditions leading to selective adsorption (surface modification) and subsequently to possible efficient separation of these two minerals are discussed in this paper.

Jan 1, 2002

By Paul Lenchuk

The concrete block industry can trace its beginnings to the early 18th century when most of the experimental work was being carried out in England. In America, the concrete masonry industry got started shortly after the Civil War and has had sometimes a spectacular, but always a steady growth since then. From a few hundred thousand concrete masonry units made in the late 19th century, the industry today produces approximately 3.3 billion concrete masonry units making it the largest industry in the United States for masonry wall materials. There were 3500 concrete masonry plants manufacturing these units after World War II. This nwnber decreased to 1500 by 1970 although the production of concrete masonry units increased by over 100% in the last 25 years. One of the reasons for this increase in production by less than half of the plants which once existed, is the tremendous strides made in automation of production machinery. The concrete masonry plant of today is probably one of the most automated small businesses in existence. Within a few years it will be possible to push a button and the entire manufacturing process will begin with no human hands touching the units until they are laid up in a wall at the manufacturing plant and are trans-ported to the job site. No other concrete product has reached this state of manufacturing sophistication and it is one of the reasons why the price of a concrete masonry unit is not much different than it was 2S years ago. Because of automation, it is safe to say that concrete masonry will remain a highly competitive building material for many years to come. The problems that beset the continued use of this material are not related to the cost of manufacturing and delivering the product. What are some of the problems as well as some of the opportunities and is the golden age of opportunity knocking rather than a wolf in disguise? The use of concrete masonry has grown each year because a larger unit was provided at less cost than other competitive materials. Concrete masonry has had severe competition from the clay products industry as well as masons who laid the product in the wall and who resisted concrete masonry for many years. Even today

Jan 1, 1971