Search Documents

By Stephen C. Tadolini, Colton Cook, Cody Hildreth, Frederick Cybulski

"Broken and jointed ground is extremely hazardous and requires unique stabilization techniques to protect worker and critical entries. Bolting techniques, even the most advanced with pre-load to create roof compression, can leave large gaps of unconfined and separated roof. This roof can also be susceptible to water inflows which only exacerbate the support problem. These types of conditions existed on long term development main entry accessing several future longwall panels. The geotechnical assessment identified well-defined jointing systems that also permitted water to flow between the roof separations, which “lubricated” the roof material and minimized any frictional advantages. Chemical injection of a Polyurethane material, Minova Carbopur WS, was placed beyond the bolted horizon to move the water to the rib lines and reinforce the fractured and broken roof. The injection material permitted the effective use of bolting patterns and helped ensure long-term stability of these critical entries. The paper describes the evaluation techniques, design patterns, basis for chemical selection and application, and results and recommendations.BACKGROUNDThe injection of mine and underground civil structures using polyurethane (PUR) has been ongoing for over 50 years. The applications in mining have included gate road stabilizations, longwall set-up and tear-down entries, and simple consolidation of coal mine roofs. PURs have also been used for roof stabilization during longwall shield recoveries. Polyurethane injection was initially developed by the Bergbau-Forshung GmbH, a German coal mine research institute, in the early 1960s (Jankowski, 1972). The product became a standard stabilization method in Germany after its commercial introduction in 1971 (Knoblauch, 1994), and was successfully manufactured at the Minova Essen, Germany location for over 50 years. With the recent closing of the German underground mines, that manufacturing facility has been closed and moved to Katowice, Poland, where production continues today Injection products are also being successfully manufactured by Minova in Australia and the United States.Polyurethane injection in underground coal mines is used in difficult ground conditions in fractured immediate and main roofs. It is also common as a rock stabilization remedy to prevent longwall face caving during shield removal. As presented in the case study, polyurethane was applied to minimize the inflow of water from beneath a stream channel while providing reinforcement and consolidation of the fractured roof that had lost confinement. Polyurethane is a two-component system (Part A and Part B) that is injected into a borehole and can chemically bond to the rock, not relying on friction or mechanical interlock to provide support. The material is injected under pressure, coupled with a low viscosity and small particle size; it flows into roof fractures and separations, which are the paths of least resistance. New developments in low viscosity PUR materials allows penetration of cracks as tight as 0.002 inch (0.05 mm) wide. This also allows for the closures of extremely small cracks to minimize the inflow of water, even if the water is under pressure. Combinations of designed expansion properties and low viscosities make the materials ideal for minimizing and stopping flows of water from underground structures."

Jan 1, 2019

By P. Eger, D. Green

"The Soudan Mine was Minnesota’s first iron mine, operating from 1882 to 1962. The mine was donated to the State of Minnesota in 1963 and became a state park in 1965. The mine discharge contains elevated copper and cobalt concentrations and has been treated with an ion-exchange-resin-based system since 2009. The system includes flow equalization tanks, bag and cartridge filters, a carbon tank and two commercial ion exchange tanks. Although effective, the system’s high cost, inefficient removal of suspended material and substantial maintenance have been ongoing and troublesome issues.In November 2012, we initiated a pilot test using a peat-based sorption media. This media is produced from raw reed-sedge peat through a patented, low-temperature carbonization process that produces a hardened granular sorption material. The granules are uniform, have high hydraulic conductivity and maintain the high metal affinity of natural peat.Mine water was pumped through the peat-based sorption media without any pretreatment. Copper input concentrations typically ranged from 30 to 60 µg/L but increased to a high of 364 µg/L in the summer of 2013. Since startup, more than 60 million L (16 million gal or 32,000 bed volumes) have been treated, with average removal rates of 75 percent for particulate copper and 60 percent for dissolved copper. Backwash is required at about 4,000 bed volumes, but with a combination of air sparging and high-flow backwash, the suspended material is removedfrom the media.One tank of the peat-based sorption media was found to remove copper similarly to the first four components of the existing system. By reducing size and complexity, reductions in operation and maintenance costs are possible. A comparison of the estimated costs indicate that replacing the four initial components with the single media tank has the potential to reduce annual operating costs by more than half from around $163,000 to $70,000."

Jan 1, 2015

By P. M. Soupios

There is an increasing requirement for geophysical surveys carried out during geotechnical investigations to provide direct information about rock quality or other geotechnical parameters. With the paucity of information to correlate geophysical results with actual rock properties, this is still difficult to achieve and additional research effort needs to be performed to address this issue. Nowadays, several researchers have been described detailed studies which designed specifically to investigate this matter. Generally, geophysical techniques which are used to estimate seismic velocities in the subsurface focus on the low strain levels that are not large enough to induce significant nonlinear, nonelastic stress-strain behavior (Luna and Jadi, 2000), which is normally evaluated when addressing liquefaction potential of soils in the shallow subsurface. Soil parameters relevant to seismic ground response (Rechtien, 1996) are density, relative density and void ratio, permeability, shear modulus, water saturation, soil fabric and stress history. Detailed characterization of elastic properties near a major construction site (e.g. a bridge) is useful for near field dynamic analysis of soil-structure interaction (SSI) effects. The coupled effect of the bridge foundation (piles, piers or abutments) and the soil immediately surrounding these substructure elements is essential for dynamic SSI analysis of these critical bridge structures. This paper presents a geophysical investigation performed along the under construction highway of Egnatia Odos, approximately 13 km west from the town of Xanthi in N. Greece. Twelve geotechnical boreholes, drilled at the maximum depth of 75 m, approximately located 20 m from the Nestos River. The objective of the survey was to obtain the high-resolution compressional and shear wave velocities of the shallow subsurface for computation of elastic engineering properties of the unconsolidated material interposed between the investigated boreholes. Joint interpretation of borehole logs and velocity images obtained by P- and S-wave traveltime inversions outlined shallow geological anomalies.

Jan 1, 2005

By Timothy J. Orr, Robin J. Burgess-Limerick, Jennica L. Bellanca, MARGARET E. RYAN

Powered haulage continues to be a large safety concern for the mining industry, accounting for approximately 50%of the mining fatal accidents every year. Among these fatal accidents, haul-truck-related accidents are the most common, with 6 of 28 and 6 of 27 fatal accidents occurring in 2017 and 2018, respectively. To better understand why these accidents continue to occur and what can be done to prevent them, researchers reviewed the 91 haul-truck-related fatal accidents that occurred in the USA from 2005 to 2018 and performed bow-tie analyses using the final reports published by the Mine Safety and Health Administration. The analyses explore the context of the accidents with a focus on the initiating event, event outcome, hazards present, and possible preventative and mitigative controls. Overall, the vast majority of the accidents resulted in a haul truck colliding with the environment, and the majority of these events were initiated by loss of situational awareness or loss of control. The majority of the hazards were related to design and organizational controls. The results of this study suggest a need to investigate operator decision-making and organizational controls and to focus on improving design and operation controls such as mine design and operational procedures.

Feb 22, 2021

By Giovanni Barla

This paper examines the application of gelatin mixture models to the study of factors such as gravity effects, tectonic and residual stresses, anisotropy, physical nonlinearity, time-dependent behavior of the rock mass and connectedness of the geologic space. The calibration technique of gelatin mixtures, proposed by Richards and Mark in 1966, is applied to the particular problem considered. Similitude relationships between model and prototype are discussed with reference to the constitutive equations describing the physical behavior of the rock mass. The interaction between two openings in a linearly elastic medium, under conditions of plane strain, is used as an illustrative example, with the view of describing the history of stress and deformation changes on the rock medium and lining around a slusher drift while undercuts are made in block caving.

Jan 1, 1968

By R. E. Lindstrom

The mineral bastnasite is utilized to describe alternate processes for the extraction and separation of the rare-earth elements by solvent extraction. The rare earths can be acid-leached directly or fused with NaOH before acid leaching. Cerium, the major constituent, can be recovered by fractional precipitation, fractional leaching, or solvent extraction with tri-nbutyl phosphate. The latter process is capable of producing 99.5-percent pure CeO2 at 98+ percent recovery. Lanthanum is subsequently recovered by fractional precipitation or solvent extraction with a nitrogen-based extractant. A 20-stage mixer-settler operation with a primary amine extractant results in a 95-percent pure La203 fraction at 96 percent recovery. Europium is amenable to extraction from most of the remaining rare earths with an organophosphate extractant. Selective stripping of the europium, followed by reductive precipitation, produces high-purity Eu203. Another possibility for europium purification involves the differential extraction of europium with an amine followed by a sub- sequent reducing strip. Separation of the remaining elements is more difficult but can be accomplished with amine or quaternary ammonium extracts. Typical separation factors achieved are 3. 8 for praseodymium-neodymium and 10. 5 for neodymium-samarium.

Jan 1, 1967

By Brij M. Moudgil

Florida produced more than eighty percent of domestic phosphate during 1974. This amounted to more than thirty-five million short tons. Ninety percent of this production was used in the production of fertilizers. Other uses of phosphate include food preservatives, fabric dyes, optical glass, photographic films, soaps, plastics, pharmaceuticals and animal feed ingredients. Marketable phosphate rock projections for the nest decade forecast a very healthy growth for the Florida phosphate industry. Associated with the expansion, however, are the corresponding problems of water conservation, air and water pollution and land reclamation. Recognizing mining as an interim land use, the industry is presently engaged in a very active reclamation program. The proximity of the central Florida deposits to rapidly developing urban areas makes it important to undertake successful and well planned reclamation programs. Water use and conservation is of vitil importance to the industry. Water withdrawal from existing aquifers and discharges into drainage systems are closely regulated by state agencies. Water is stored and recycled to maximize usage. In some instances water is even returned to major aquifers through a series of recharge or connector wells. The phosphate industry has spent over 200 million dollars in the past decade for research, development and implementation of pollution abatement and water conservation systems.1 The following discussion outlines various phases of phosphate mining in central Florida today, with emphasis on research in waste disposal techniques and progressive land reclamation programs.

Jan 1, 1975

By Kallam V. K. Reddy, VADAPALLI SANJANA, Veerendra Singh, Gajanan Kapure

This work describes a leaching process for the conversion of high-magnesium peridotite rock, which is a chromite ore overburden, into two valuable products: magnesium salts and micro silica. Under normal leaching conditions, residue remaining after leaching is of a gelatinous nature and thus hinders the filtration process. To address this issue, oxidative leaching with the addition of H2O2 was employed, and it significantly improved the filtration kinetics. Four different approaches for H2O2 addition were tried, and they all proved effective in controlling gelation. The optimum oxidative leaching condition was 70 °C, 2 h time, 2 M H2SO4, 0.5MH2O2 and 400 RPM; under these conditions, 92% magnesium leaching efficiency was achieved. After leaching, the leach liquor obtained was purified and dried into Mg(OH)2 and MgSO4 salts. The leach residue contained mainly silica particles, with size in the 10–30 μm range. This material thus represents an attractive candidate for the production of highperformance concrete for the construction industry. The oxidative leaching process described here enabled the complete conversion of peridotite into valuable products, magnesium salts and micro silica.

May 5, 2020

By Ernest M. Spokes

Maximum fan efficiency can only be obtained when the fan has the correct combination of size, speed, and blade setting to provide the required flow of air against the mine resistance. As the mine grows older, resistance decreases unless old workings flow is restricted, and new combinations of speed and blade setting or different fan sizes may provide greater economy.

Jan 1, 1977

By R. L. Beatty

Bond International Gold's Colosseum gold mine was discovered in 1865. No recorded production occurred, however, until the 1930s, with production of about 19 kg (615 oz) of gold. The mine was closed in 1942 as a nonessential industry during World War II. The property was acquired by Dallhold Resources in mid-1986. Construction of a 1.1-million Mt (1.2-million st), carbon-in-pulp (CIP), cyanide mill began in November 1986 and was completed in September 1987. Minable reserves are estimated to be 9.5 Mt (10.5 million st), with an average grade of 2.1 g/t (0.061 oz per st). This article describes the general process flow and plant equipment. And it looks at the maintenance and operational problems encountered in the first six months of operation. Process description Ore is direct hauled from the open-pit mine 1.5 km (1 mile) to the crushing facility. There it is crushed to -152 mm (-6 in.) with a single- stage, 1.5-m x 1.2-m (60-in. x 48-in.), 186.5-kW (250-hp), Fuller-Traylor jaw crusher. The ore is then stockpiled in a 31.7-kt (35,000-st) reclaim ore pile. Lime is added to the crushed product as it is conveyed to a single 6.4-m x 4-m (21-ft x 13-ft), Hardinge semiautogenous grinding (SAG) mill, followed by a single 4.3-m x 7.3-m (14-ft x 24-ft) Hardinge overflow ball mill. After grinding, the slurry is thickened and then preaereated for three hours. Following preaereation, the pulp is leached with NaCN at a pH of 11, also for three hours. The slurry then goes through a seven-stage CIP circuit for 21 hours. Then the tailings slurry is preaereated for three hours before cyanide destruction using the Inco process. Loaded carbon is eluted using an Anglo American strip, followed by electrowinning on stainless steel wire. The stainless steel wire is transferred to refinery cells where the gold and silver is plated on stainless steel plates. Following electrore-fining, the gold-silver foil is removed, melted, and poured into dore bars for shipment. The crushing, milling, refining, and maintenance processes require 37 people. Crushing The crushing area required changes and modifications following start-up. Several areas are of specific note. Structural failures Rubber support cushion blocks located under the coarse ore bin failed. These were replaced with heavier, more durable blocks and have since appeared to be satisfactory. A severe structural vibration was encountered in the entire crushing facility. A mechanical engineer, brought in by the contractor, determined the structure needed more support and cross-bracing.

Jan 1, 1989

By Bo-Hyun Kim, Mark K. Larson

"Researchers at the National Institute for Occupational Safety and Health (NIOSH) have advocated the use of instrumentation in underground mine ground control studies to aid in understanding failure mechanisms and to calibrate numerical models. The purpose of these efforts is to reduce accidents and fatalities in underground mines resulting from inadequate design of mining layout or supports. A recent examination of some results of stress change measurement raised some questions about the validity of elastic solutions in ground, such as coal. Particularly under deep cover as is prevalent in the western United States, the coal around a borehole would likely have yielded so that post-yield behavior would govern the response of the instrument.A numerical experiment was conducted by NIOSH researchers using the FLAC software (Itasca Consulting Group, 2016) to investigate the response of the borehole pressure cell (BPC) and the biaxial stressmeter to varying degrees of plastic behavior. The pre-encapsulated BPC cell pressure exhibits increasing departure from the elastic case with decreasing post-peak-strength slope of the stress-strain curve. On the other hand, because the BSM usually provides much more confinement to the surrounding rock than does the BPC, the measurements obtained from the BSM do not depart significantly from the changes in secondary principal stresses and directions as calculated by the elastic solution.INTRODUCTIONSeveral years ago, Larson et al. (2000) described several instruments that NIOSH had used in underground field studies and how to monitor them with dataloggers. This information is still relevant because of the need to understand how excavation affects the stability of mines and thus, the safety of mining personnel. One class of instruments described in that paper includes those instruments that measure change in rock stress. Although several such instruments might be used to measure stress change, the focus of this paper is on two instruments with which NIOSH has had more recent experience—the borehole pressure cell (BPC) (Geokon, 2018a; RST Instruments, 2018) and the biaxial stressmeter (BSM) (Geokon, 2018b). Other instruments, such as the CSIRO hollow inclusion stress cell (HICell) (Earth Sciences, 2019; Worotnicki and Walton, 1976) may be included in future studies.Early studies in the development of the BPC were those of Panek and Stock (USBM, 1964), Sellers (1970), Lu (1984), and Babcock (1986). Babcock’s work is particularly useful, but his setting and testing range was far below what we experienced in the NIOSH study, and it was Babcock’s data reduction scheme from his laboratory experiments that was used to calculate stress change in the NIOSH study (NIOSH, 2019a)."

Jan 1, 2019

By L. B. Rothfeld

This paper presents preliminary results of a Bureau of Mines study of potential costs of compliance with the federal Resource Conservation and Recovery Act for copper heap and dump leaching. Specifically, estimates are given for the cost of compliance with possible technology standards that would require the use of liners and closure caps regardless of terrain and underlying geology and hydrology. This cost is compared to the co lit of compliance with present state requirements for terrain a typical of those found at existing copper leach sites in the Southwestern U.S.A. Incremental compliance costs are found to widely exceed screening criteria used by the Environmental Protection Agency to denote significant economic impact.

Jan 1, 1993

By S. Rukhaiyar, M. Ramulu, G. Pradeep, P. K. Singh, P. B. Choudhury

The drill and blast method is the most prominent rock excavation method used in mining and civil engineering projects. The ground vibration is the most undesirable effect of the blasting and needs to be controlled. The blasts are designed so that ground vibration at nearby structures must remain under the prescribed limit. Various empirical blast vibration attenuation models have been presented to estimate the ground vibration for designing purposes. These models assume ground vibration as a function of distance and maximum charge per delay. United States Bureau of Mines (USBM) model is most commonly used for the blast design. However, the uncertainty associated with these models is seldom characterized, thus diminishing its reliability. The probabilistic Bayesian approach associated with the Monte Carlo method can easily quantify uncertainties associated with the model and its parameters. Thirty-three blast vibration observation data from a granite quarry in Kerala, India, is used to estimate the probability distribution of model parameters. Markov Chain Monte Carlo (MCMC) approach is used for sampling 12,000 samples for obtaining the posterior distribution of parameters. The uncertainty associated with model parameters is quantified from the posterior distribution, and this is further used to estimate the credible and prediction limits of the model. The point estimate of the most optimum value of the parameter is estimated using maximum-aposteriori or MAP estimate. The model parameters are also obtained using the commonly used least-square error method, which is a maximum likelihood estimation or MLE approach. It has been observed that the accuracy of the model obtained using both MAP and MLE approach is almost equal. However, the MAP estimate as per Bayesian probabilistic analysis has the added advantage that it can estimate the uncertainty of parameters as well as the model, which is not possible using the MLE approach.

Sep 27, 2021

By H. Jiang, Y. Luo

The study develops an automated, high-efficiency drilling control system to reduce respirable dust and increase energy efficiency in underground coal mines. It uses specific energy to evaluate efficiency and proposes a comprehensive drilling control algorithm based on laboratory tests. The algorithm optimizes drilling parameters to maintain high efficiency, reduce dust generation, and improve safety.

Feb 12, 2022

By Mirjana Boskovic

LKAB’s Kiirunavaara Mine is a sublevel caving iron-ore mine located above the polar circle in northern Sweden. The mine has been proclaimed seismically active since 2008 after a magnitude 3 seismic event, according to Swedish National Seismic Network (SNSN). At that time the Kiruna Mine did not have mine-wide seismic system. Since then, the Kiruna Mine experienced several damaging seismic events of which the largest one on the May 18, 2020. The magnitude, based on the moment tensor inversion results on data from the SNSN as well as seismic stations in Finland and Norway, is estimated to 4.2 ± 0.2 moment magnitude. The seismic event on the May 18, 2020 was located in the middle of the one of the productions areas and caused the major damage in the mine, damaging several kilometres of drifts on six mining levels, some of them beyond the practical repair. These damages affected four of ten production areas on several levels, some more some less. Luckily, no person got injured from the seismic event and the very long aftershock series. An important part in the whole process after the seismic event was information flow and decision-making process. It was very important to keep workers and community informed as that contributed transparency of decision-making and decreased the speculations. Resuming the production in the damaged areas in the safe manner, very soon become main focus for the mine management. It was obvious that not only rehabilitation of the areas is needed to resume the production. It was A MUST to understand the factors behind the seismic event and its mechanism to be able to avoid same situation and prevent seismic event of similar size. Mine engineers had to think outside the box to find the solutions to ‘rescue’ every drift that they could to be able to make good enough base for continued mining of the area. The paper describes actions taken in a very complex process of recovering the area that we from the beginning thought need to be abandon. Seismological analyses of the event on May 18, 2020 and past activity in the area, damage mapping, detailed studies of structures and geology, numerical modelling as well as engineering judgement were used as base for all our decisions how to proceed in attempt to restore mining of the area heavily damaged by 4.2 moment magnitude seismic event, in a safe way.

Apr 26, 2022

By S. S. Peng

In dealing with the mining engineering problems, the traditional approaches of laboratory experimental simulations and/or analytical solutions are not very effective. Mainly because the field problems are too complex to be solved with a few simplified assumptions. Conversely it is also true that the experimental and analytical/ numerical models currently available are far from being able to model the actual cases. Under such conditions, the most effective mean of research into mining engineering problems is to combine the mine (field) investigations with laboratory and / or analytical modelings. It is with this concept in mind this research was initiated in 1973. 'The field investigations which began in the fall of 1978 consisted of mainly visiting the mines where surface subsidence monitorings had been or were being monitored and/or surface structural changes had occurred. From such visits, subsidence data were collected. A quick analysis of those data provided preliminary understandings of the characteristics of the surface subsidence parameters in the regions (1-5). Using those date, models of various types are being developed for subsidence prediction / control. So far, a total of 44 longwall subsidence profiles in 22 longwall panels and 10 room-and-pillar profiles in 5 room and-pillar sections have been collected. This paper summarizes the combined results published previously (1-5) and present the preliminary results of the predictive models developed.

Jan 1, 1982

By E. Cameron

Yeelirrie lies toward the center of Western Australia, 650 km (404 miles) northeast of Perth (Fig. 1). The ore reserves have been estimated as 52.5 kt (57,871 tons) of contained U3O8, at an average grade of 0.15%, of which almost two-thirds average 0.24% U3O8. the ore body is a thin, elliptical, more or less horizontal sheet measuring approximately 9 km (5.6 miles) in length, between 0.5 and 1.5 km (0.3 and 0.9 miles) in width, and up to 7 m (23 ft) in thickness, extending from the surface to a depth of 8 m (26 ft). In spite of its near surface position, there is only one small outcrop of significant mineralization. Carnotite is the only uranium mineral recognized so far, dispersed through a calcrete horizon, and deposited from circulating ground water which was also responsible for the carbonation of the clays completely filling an Early Tertiary drainage system. Calcrete, as seen at Yeelirrie, is quite distinct from the widespread, thin pedogenic horizons, as it often forms bodies many kilometers in length and up to 20 m (65.6 ft) in thickness, elongated parallel to the drainage lines. It is variously referred to as "valley calcrete" or "ground water calcrete" to emphasize the occurrence and mode of origin. The discovery of Yeelirrie in mid-1971 was the successful culmination of a grass-roots exploration program initiated in 1968 as part of Western Mining Cop's program of diversification from its historical position as a major gold producer. The object was simply to find an economic uranium deposit - with no constaints other than those normally taken as applying in the mineral search. There was, therefore, complete freedom in the selection of the exploration model, or models, to be applied and the areas to be considered, though the choice was inevitably influenced by both the nature of world occurrences and the local geology. One of the options avail- able was the sandstone environment. Yeelirrie was the direct result of pursuing this line of investigation through three sequential, but quite distinct, stages: first, a regional study; second, establishing a case for exploring the inland drainage systems of Western Australia; and finally, an evaluation of the calcrete environment. An assessment of the potential for sandstone-type deposits in Australia necessitated going back to first principles, since there were no known precedents in this country for guiding exploration and, as a consequence, the search need not be influenced by established prejudices. Previous uranium exploration during the 1950s had been preoccupied with vein-type deposits, and, although the sandstone environment was undoubtedly being examined in 1968, no discoveries had been announced to that time. When considering the necessary ingredients -a source of leachable uranium, a circulating ground water system, and a suitable reducing environment - it could be argued that considerable areas in the eastern part of the continent were theoretically prospective, but basin depth and the extensive superficial cover of Mesozoic and Cainozoic sediments presented considerable practical difficulties.

Jan 1, 1991

By K. V. Raj, R. Jacksha

Conveyor systems persist in being a source of injuries and fatalities in the mining industry. To reduce these incidents, better methods are needed to enhance the monitoring of probable hazards and improve situational awareness during the normal operation and maintenance of conveyor systems. To address these issues, researchers from the National Institute for Occupational Safety and Health (NIOSH) continue to investigate emerging technologies that show the potential to improve miner safety around conveyors. This paper presents a feasibility assessment by NIOSH researchers of a fully integrated, commercially available wireless Internet of Things (IoT) system to improve situational awareness around conveyor systems. Included are discussions of a full-scale laboratory test bed that was designed to simulate a working conveyor system as well as the challenges and successes of integrating the IoT system with the test bed.

Oct 6, 2020

By Roberto L. Romero

The dressing of Bolivian tin ores has been done up to the present by classical. gravity methods, taking advantage of the high specific gravity of cassiterite compared with that of the accompanying gangue. For this purpose, jigs and shaking tables are used in the treatment of the various size fractions in which the ore is classified. Bolivian ores are mainly of the vein type and, to obtain a reasonable separation, crushing and several stages of grinding are necessary during the process to substantially liberate the cassiterite from the gangue. Gravity processes for cassiterite are effective for sizes down to 200 mesh. Below this size the efficiency of the gravity methods falls off very rapidly with increasing fineness of the mineral grains. The conventional treatment for this material is desliming followed by tabling on shaking tables various other types of machines have been designed for the gravity treatment of these fine particles but they have had limited success. Bolivian ores contain an appreciable amount of minus 200 mesh material constituted by "primary fines" caning from the mine itself, and "secondary fines" originated during the crushing and grinding necessary for liberation of the difficulty in the treatment of these fine particles is one of the causes why the recovery of tin in concentrates is only of around 50% in the mines owned by Corporacidn Minera de Bolivia, the State owned enterprise. The average figure for other Bolivian mines is

Jan 1, 1971

By D. R. Tesarik, T. C. Trancynger, W. G. Pariseau

The Davis detector cavern was excavated on the 4850 Level of the former Homestake Mine in the mid- 1960s to house a novel neutrino detector developed by Nobel Prize winner Dr. R. Davis. The original cavern was about 9.1 x 16.8 x 9.7 m high, excavated in a Precambrian amphibolite known as the Yates unit and enlarged in 2010. In 2009, the National Science Foundation selected the site for development as a national Deep Underground Science and Engineering Laboratory (DUSEL). This retrospective rock mechanics study of the Davis cavern is intended to inform design of the much larger caverns and laboratory rooms being considered for the same 4850 Level. Provision for rock mass variability, sequential excavation, jointing and wall damage from blasting are included in analyses that were done using two different computer codes and methods (FLAC3D and UTAH3). The results are in agreement with observations and show that cavern stability is indeed the case. The main conclusions are: (1) if conventional scaling of laboratory rock elastic moduli and strengths is done, then 0.25 and 0.50 scale factors are reasonable, (2) measured statistical and spatial variability in rock properties should be incorporated into geomechanical analyses to better reflect reality, (3) discontinuities (“joints”) are essential to reliable analysis of excavation safety and when properly taken into account eliminate the need for empirical “scaling” of laboratory rock properties, (4) major geologic features such as rhyolite dikes and breccia zones may be important to excavation safety at Homestake and should be explicitly represented in analyses and (5) quantifying wall blast damage is important to engineering design of underground excavations.

Jan 1, 2012