Search Documents

By M. E. Gershon

Conventional methods of drill hole site selection are reviewed briefly. Two approaches using geostatistics are then discussed, both of which have been shown to yield improved results. Finally, a branch and bound algorithm is described which will select the best locations for drilling from a user specified number of possible drill sites. Two options are discussed. First, the user can specify a maximum drilling investment or a maximum number of drill holes and the program will select the locations yielding the minimum estimation variance. This amounts to getting the most for a given investment. Alternatively, a maximum tolerable estimation variance can be specified and the program will select the number and location of the drill holes to obtain the desired information at a minimum cost. Another benefit of the approach is the quantification of the tradeoffs between investment and information obtained.

Jan 1, 1985

By Eduardo M. Sacris

The performance of the grinding circuit, from the initial stages of operation to the present, is discussed. The mill efficiency as measured by the Bond grindability data and the operating work index is presented. The objective has been to produce a sand cyclone overflow containing not more than 6% +65 mesh. However, this has never been attained even at low milling rates. On the other hand, significant improvements in throughput were achieved by instituting some equipment changes and process modifications within the grinding circuit. The latest approach to solving the coarse grind problem is also discussed.

Jan 1, 1983

By Peter G. Chamberlain

Domestic mining will not produce a significant portion of the manganese consumed in the United States unless new mining and processing techniques are implemented that will enable domestic lean ores to economically compete with rich foreign ores. One mining-processing technique that appears promising for certain deposits is in situ and/or heap leaching with aqueous SO2. Since leaching offers economic advantages of low capital costs, low operating costs, and short start-up times as well as environmental and safety improvements over conventional mining-processing, the Bureau of Mines studied the leachability of manganese deposits from several districts. Manganese oxides, hydroxides, and carbonates were leached to 80 to 90 pct recovery in 7 to 40 days of leaching with a solution containing 5 pct SO2 in column leaching tests. Preliminary cost analyses of surface mining-heap leaching, block caving-in situ leaching, and shrinkage stoping-in situ leaching indicate that the products of manganese leaching may be economically produced for the chemical and electrolytic manganese industries. The easiest marketable product to obtain would be a manganese sulfate commonly used as a fertilizer amendment. Manganese carbonates and hydroxides could also be precipitated from the pregnant leach solutions.

Jan 1, 1983

By İsmail İnce

The purpose of this study is to investigate the index-mechanical properties of igneous rocks by using the electrical resistivity method. Electrical resistivity, index (P-wave velocity, dry density, and porosity), and uniaxial compressive strength values of 48 different igneous rock samples were measured in the laboratory. Simple regression analysis was performed between index-mechanical properties and electrical resistivity values. Strong exponential and logarithmic correlations were found between electrical resistivity and the index-mechanical properties of the igneous rock samples.

Jan 21, 2022

A bearing isolator is a noncontact, nonwearing, permanent bearing protection device. It has a rotor and a stator, and the two are unitized, so that they do not separate from one another while in use. The rotor turns with a rotating shaft, while the stator is pressed into a bearing housing. The two components interact to keep contamination out of the bearing enclosure and the lubricant in. Bearing isolators do not require lubrication or any particular shaft finish or condition. The best bearing isolators are made of metal, usually bronze. They use a vapor-blocking feature that inhibits the free transfer of vapor contamination when the rotating equipment is cycled on and off.

Jan 1, 2004

By N. Chow

The recovery of manganese from lower-grade resources has been studied for a number of years. Of key importance in prior work was the discovery that higher-valent manganese can be readily leached with sulfurous acid. This eliminates the need for high-temperature reduction roasting that is conventionally used in processing high-grade material. High-temperature roasting is energy intensive, emits a large amount of carbon dioxide and would not be economical for processing lower grade material. While the prior work provides important information for extracting manganese from lower-grade resources, the production of unwanted byproducts and high water and energy usage has limited its commercial use. This paper describes the results from laboratory work that demonstrate solutions to problems that to this point have precluded commercial development. Preliminary mass and energy balances show that a significant opportunity exists in producing manganese with this hydrometallurgical scheme in a low-cost, environmentally friendly manner. The emphasis of the work is on low water use, low overall energy use and economic destruction of unwanted byproducts.

Feb 1, 2012

By M. Deul

For the first half of the 21st Century the USA will rely on the same mix of fuels as for the past 50 years: Petroleum will cost more and availability will decline as developing nations modernize. Increased use of natural gas for electric power generation will result in severe stress on gas supply. Coal will be the fuel of last resort. More than half the petroleum used is imported, about the same amount as used for transportation. Only coal can provide relief by fueling railroads through electrification while encouraging ‘piggy-back’ trailer haulage, co-generation for manufacturing and expanded passenger service.

Jan 1, 2002

By A. M. Gaudin

A new method of measuring the viscosity of unstable suspensions has been developed, using a Heinz viscometer. The technique was applied to kaolin-water suspensions. Spreads in viscosity with lime additive were measured.

Jan 1, 1962

By W. C. Dailey

The Groveland Mine. Concentrator and Pellet Plant are located in Dickinson County in the Upper Peninsula of Michigan. The construction of the Groveland Mine in 1959 was the first United States operation for the Hanna Mining Company in mining and beneficiating low grade iron formations. (1) The plant produced concentrates at 675,000 lt/yr. (746,600 mt/yr.) which was used as sinter feed in the steel industry from 1959 to 1963. Upon completion of a pelletizing plant in April, 1963 production increased to 1.6 million lt/yr (1.77 million mt/yr) of pellets. After the plant expansion, mill capacity increased to 2.2 million 1t/yr (2.43 million mt/yr.), producing 2.0 million It/yr (2.23. million mt/yr.) of pellets assaying 63.0% iron and 7.0% silica. (1) Prior to April, 1971 the concentrator operated with a flowsheet consisting of spirals and a petroleum sultonate iron notation circuit. This was presented in a paper by R. R. Smith and E. E. Sougstad, "Flotation at the Groveland Mine" in the 50th Anniversary Volume entitled "Froth Flotation". The ore body at the Groveland Mine consists basically of two types of iron formation (34% total iron, 20% magnetic iron head), the most abundant of which is a bedded magnetite-chert-silicate rock. This is intermingled to varying degrees with non-bedded to poorly bedded hematite-clastic quartz-chert rock. (1) In developing the Groveland flowsheet, Humphrey spirals were used because of their ability to produce a coarse size concentrate at a low cost. Tests run in the lab and pilot plant on the Groveland ore showed a. spiral weight recovery in the 27 to 33% range. (2) However as the ore body was opened up, it became evident that the most abundant ore type did not liberate at the coarse size fraction needed for spirals. Plant recoveries for the first five years operating the spirals only averaged from 10 to 15% weight recovery. In 1971 the weight recovery on the spirals had dropped to a low of 5%. To increase iron recovery and at the same time increase plant capacity with the least effect on the present operations the mill flaw-sheet proceeded from a spiral-notation circuit to an all flotation circuit to a magnetic separator-flotation circuit. During this changeover the concentrate grade also had to be improved to meet market demands. To do this the following changes evolved

Jan 1, 1978

By G. T. Austin

This is an overview of the gemstone industry with special attention on particular states within the united states. The U.S. Bureau of Mines, Department of the Interior compiled and analyzed the information contained in this report. The report should be viewed as a current "still photograph" of a dynamic system. The information presented on a specific gemstone or for a specific state can and will change with time. This overview presents historical and reference information on the principal gemstones and their production in certain states. The report is not a definitive work on gemstones within the select states or United states.

Jan 1, 1995

By James E. Lawver

Part I describes the general geology of the Florida deposits. As the lucrative Bone Valley Formation is depleted, replacement production will move progressively into areas of total Hawthorn production. The reserves of the immediate future are a mixture of two distinct ore types referred to as the upper (high grade) zone and the lower (low grade) zone. The upper zone is somewhat similar to the Bone Valley Formation that has been Florida's source of production for the past 100 years and will respond favorably to present beneficiation practices. By contrast, the lower zone ore contains significant quantities of dolomite that must be removed in order to produce an acceptable grade pebble or flotation sized product. Part II reviews past practice and describes future trends in mining and ore transportation. This presentation (Part III) is confined to the problems of beneficiation, waste disposal, and environmental regulation.

Jan 1, 1983

By K. K. Kohli

Since the adoption of the Surface Mining Reclamation and Control Act of 1977, which mandates that surface subsidence be an intergral part of the underground coal mine design, there has been a sudden rise of demand on guidelines for minimizing surface subsidence and its associated structural damages. Unfortunately there is no sufficient amount of systematic subsidence data to fill such a gap, although considerable research has been devoted to the subsidence-induced damages of surface structures in the past. However, it was said that many surface subsidence surveys have been performed and monitored by coal companies during the past twenty years, and that it will be a great source of information for subsidence engineering design if they can be collected and assembled together. An effort was therefore initiated in the Department of Mining Engineering, West Virginia University, under contract with the U. S. Bureau of Mines in December 1978 to contact each individual coal company in the Northern Appalachian Coal Field for any surface subsidence survey data. After 10 months' survey, the data collected include 17 longwall panels and 2 room and pillar sections. The data in-each panel and section cover the complete set of subsidence survey raw data, underground mine layout maps, surface topo maps, geological loggings showing the stratigraphic sequences and thickness of the overburden, and if available, locations and types of surface structures. On-site visits were followed to study the surface terraines and structures. Interviews were conducted with the owners of the surface structures in most cases about, if any, the history and characteristics of damages.

Jan 1, 1980

By M. Westerstrand

The processes involved in the concentration of magnetite ore with process water as the aqueous medium can have a strong influence on the surface properties of the magnetite particles. In this study, different leaching methods, as well as zeta potential measurements, were used to examine the major easily accessible ions on the particle surfaces and their effect on the surface charge. The results show that the enrichment of elements on the surface of the particles appears early in the refinement process. Ca was enriched up to 15 times and Si up to 50 times compared to what pore water alone would have given. The leaching experiments also showed that the addition of water glass increased the surface enrichment of Si and that the collector might hinder desorption of Ca. An alkali leaching method was evaluated, which showed that Si was much more enriched than S and Cl. Zeta potential measurements on synthetic magnetite particles showed that process water resulted in zeta potentials different from the potentials measured for these particles in aqueous calcium and silicate solutions. Therefore, it is important to consider the complexity of the process water when making predictions about the properties of the particle surfaces in the final magnetite concentrate, which most studies do not. Zeta potential measurements were also used to rule out a strong influence from organic matter in the process water on the magnetite zeta potential.

By Robert Stefanko

13.1-SUBSIDENCE AND GROUND MOVEMENT ROBERT STEFANKO 13.1.1-SUBSIDENCE AND FAILURE This treatment of subsidence and ground movement will be confined to subsidence control for limiting surface damage by assessing the significant parameters affecting ground movements during mining to optimize mining techniques. The material will be equally applicable to evaporite mining as well as coal but will not deal with block caving or similar systems where failure is deliberately induced and surface protection is not necessary or provided. When an underground opening is established, the original equilibrium is disturbed with resultant stress concentrations. While many factors are involved in opening stability, the span (W) undoubtedly is one of the most important factors in failure. Assuming it is relatively small, the overlying rock strata can bridge across the opening and little if any movement or convergence of top and bottom will occur. However, as the span increases, a point is reached where the stress in the overlying rock strata exceeds some strength value of the rock, and the top breaks. If the opening span is limited to some subcritical value (-We) and/or is at great depth (D), a pseudo-arch will form, achielring stability before rupture occurs to the surface. The boundary of this arch is thought to approximate an ellipse in form with the major axis vertical and equal to four times W, although there has been little field research to substantiate this theory. However, if the width of this opening is increased at this horizon to some critical value (W,) or the same span is created in a shallower seam, the overlying strata ill progressively rupture to the surface and the characteristic subsidence trough is formed (Fig. 13-1) The area of the surface affected is much greater than the area of the seam extracted, depending on the "angle of draw" (a), which is the angle between a vertical line from the edge of the opening and another line extended to a point at which subsidence tails out to zero. This angle has been found to be about 35° in Europe but is rather academic, being a function of instrument precision in detecting subsidence. Since the subsidence effect is so small at any point beyond n 25° angle, this latter may be considered the practical limit of subsidence. Further- more, indications are that the angle of draw varies with depth and nature of the strata.' In a field study over a 1,000-ft-deep potash mine in New Mexico, the maximum angle of draw was found to be 51.5°.2 So far, only a single opening has been considered. However, the width of the excavation applies to any complex mining system of entries, rooms and longwalls as long as the seam has been fully extracted and the width represents the distance from one solid rib to another. It will be noted that the amount of vertical displacement varies from point to point on the surface (s), but the maximum subsidence for a given trough occurs at the center (S). This latter value may not he equal to the maximum possible subsidence (Sm) which occurs only if a critical or super- critical (+W,) width has been exceeded (Fig. 13-1). Substantial surface damage can result when subsidence occurs. Factors affecting the amount and type of ground movement are: thickness and properties of the seam, angle of draw, width of excavation, depth and type of overburden, inclinations of strata and surface, and the amount of support left in the gob. In Europe,

Jan 1, 1973

According to the Balandin's (1) "multiplet theory of catalysis", adsorption can occur only if atoms of the reactant molecules are congruent with surface atoms of the catalyst. Such a condition calls for certain definite geometrical relationships between the reactant molecules and the atoms at the surface of the catalyst. If such a match or geometrical 'fit' is not provided, the surface reaction will not take place. An appropriate analogy to this may be the lock and key theory that enzymes should fit a substrate just as a key fits a lock. Similar geometrical considerations in adsorption studies were made in connection with the flotation of minerals. Gaudin(2) and Gaudin and Preller (3) proposed that if the dimensions of collector ions are in registry with the mineral lattice, an ordered layer of adsorbed species is formed. They explained that the structural fit is one reason for good flotation of galena with xanthate. In another study, Bachmann (4) attributed the selective flotation of KC1 from NaCl with amine to the fact that the lattice parameter of the amine collector is closer to that of KC1. Schubert(5) investigated the flotation of various nonmetallic minerals with amine and pyridine, and related the dimensions of the collector ions with the anion distances of the mineral surface. He concluded that good flotation is obtained when the tolerance is within 20%. The geometrical theory has also been used by Groszek (6) to explain the preferential adsorption of n-paraffin onto the basal plane of graphite. The geometrical theory has thus been found useful in explaining adsorptive properties of an adsorbate relative to the substrate structure. The purpose of the present work is to examine the possibilities of a geometrical fit between sodium dodecyl sulfate and Cu(OH)2 surface, and to construct a crystallographic model of the surface compound.

Jan 1, 1974

By Stanisław Prusek, CHONG WEI, Huawei Xu, Jun Wang, Andrzej Walentek, Artur Dyczko, Derek B. Apel

The excavation-induced stresses transferred from the panels or pillars in upper coal seams play a key role in the occurrence of rockbursts in driving roadways during close-distance coal seam mining, which has become a common problem and threat to many underground mines. The authors established a 3D finite-difference numerical model via FLAC3D software using the closedistance coal seam mining conditions in the Zofiówka Mine as a case example to reveal the rockburst mechanism in such conditions. The excavation-induced vertical stresses are analyzed, which provides a basis to build a conceptual model to explain the possible source mechanism of the rockburst under such conditions. Nine typical rockburst indicators considering different contributing factors are then selected as the evaluation criteria to assess rockburst potential in the study site. The results suggest that the superposition of multiple excavation-induced stresses of the main drift and tailgate provides an environment for stress concentration and energy accumulation. The side abutment stress induced by mining in the upper coal seam has a “strengthening” effect to the rockburst occurrence. The great deviatoric stress induced by complex excavating situations is another important exterior cause. A strict calibration procedure should be implemented before using indicators to predict rockburst potential. A methodology was proposed to estimate the location and magnitude of rockbursts combined with numerical modeling, laboratory tests, and feedbacks from the field. The study could provide some references and guidelines for preventing and mitigating rockbursts in underground mines under similar engineering conditions.

Aug 26, 2021

By J. Perlacia, J. M. Eguiluz

"INTRODUCTION The Bulk Handling Technology has suffered an important development in the recent years, allowing the use of conveyor belts in the most important and critical applications. As a consequence of this, the reliability and lasting performance of the conveyor belt components is becoming more and more significant, thus the implementation of preventive maintenance programs is a must. The rollers are one of the consumables in the conveyor belts, which have to be changed once arrived to the end of life. The actual ways of detecting this moment always require intensive use of labour and they are not very accurate. Indeed, if the rollers get broken before replacement, the consequences could be very important, generating additional costs and operational losses. The R&D Department of ULMA Conveyor Components, has been working since early 2012 on the development of Monitored Rollers along with a Management Software to provide users the capacity to Manage and Monitor the rollers from its desk, getting continuous online information on the internal temperature of the bearings, on the working status of the rollers as well as the identification of the rollers close to their end of life so that they could be changed during the next maintenance stop of the conveyor belt. In short, a system of Preventive Maintenance for Conveyor Belt Rollers BACKGROUND AND CURRENT STATE The malfunction of a single roller in certain conveyor belts can suppose the standstill of the whole installation until its replacement, due to the risk of greater and more expensive failures like the rip of the belt. In the case of a bulk handling installation where a continuous supply of material is necessary, a bare stop of one hour could entail huge economical losses. What’s more, many conveyor belts are several kilometers length or the access to some parts of them is very complicated. Due to these difficulties the inspection and maintenance operations can become expensive and hard going, with staff going over the whole area checking the correct condition of the conveyor and rollers, which means a dangerous activity. In addition, it’s quite common to find rollers working in very harsh conditions, completely exposed to the elements or working in corrosive closed environments like underground mines. These tough working conditions together with the very demanding features of Bulk Handling sector (high loads, speed, dangerous materials etc.) can bring the unexpected failure of a roller, even being designed to support them. Thus, to have the working conditions of the rollers real time is clearly required, in order to achieve an actual predictive maintenance of the system and avoid fatal failures. Nowadays the most common procedures to identify a broken roller is to hear how it sounds or use thermo-graphic cameras to measure their internal temperature, both of them implying workers inspecting the whole length of the conveyor while the conveyor is running. This means intense use of workmanship and operational safety level reduction."

Jan 1, 2018

By S. P. Fleming

An acid mine drainage sludge containing 0.26% nickel, 0.21 % cobalt and 4.5% manganese was leached in a one-liter reactor with sulfuric acid in the absence and presence of sodium sulfite. The effects of temperature (25°C and 52°C) and sodium sulfite concentration (up to 0.03 molar) on the leaching rate were particularly investigated. The leaching rates of nickel and cobalt with sulfuric acid have been determined to be controlled by diffusion through product layer. It has been found that effective leaching conditions to give more than 90% extraction of nickel, cobalt and manganese while keeping the iron extraction below 10% come with an elevated temperature and a low sodium sulfite concentration at pH 3; for example, 52°C and 0.01 molar sodium sulfite.

Jan 1, 1992

By J. de Bakker

It hardly needs to be repeated that if coal is to continue as America’s premier source of cheap energy, it is absolutely necessary that the carbon dioxide from its combustion somehow be sequestered. A promising method proposed to accomplish this is the “indirect” carbonation of serpentine in a concentrated magnesium chloride brine. Indirect carbonation could be also applied to precipitate magnesium in lateritic nickel processing: this would not only solve magnesium-control problems in laterite hydrometallurgy, but also reduce its energy requirements and create CO2-sequestration credits. Fifty-five percent of the electricity generated in the United States comes from coal-fired power plants, and American coal reserves can last over 500 years at 1990-level consumption1. Coal is therefore both abundant and cheap: it could (and in fact probably will) continue to be an affordable source of energy, both for producing electricity and as a feedstock for liquid hydrocarbon production by Fischer-Tropsch reactions. As a result, it is important to find a workable method of permanently sequestering CO2.

Jan 1, 2007

By J. A. Cooper, M. R. Petersen, P. O. Jackson, J. C. Langford

The organic, inorganic, and radiological characteristics of airborne aerosols have been measured as a function of particle size in controlled atmosphere test chambers and operating uranium mines. Concentrations of benzo(a)pyrene in two mines ranged from 26 to 57 ng/m3 of air. The carbon chain length of adsorbed n-alkanes was correlated with particle size. Normal mining activities produced an ore dust aerosol with mass median aerodynamic diameter (MMAD) greater than 2 µm. The elements Na, Al, Si, K, Ca, Ti, V, Fe, and U exhibited elemental ratios similar to bulk ore and had comparable MMAD's. The S, Zn, and Pb were higher in aerosols than bulk ore and were associated with smaller MMAD particulates. Radon daughter particle size distributions were influenced by the kinds of particulates

Jan 1, 1981