Search Documents

By R. D. H. Bedd

GEOLOGICAL NOTES The area under discussion is situated approximately 150 m north of Loraine No. 3 shaft at ± 1500 m below surface. The block being mined extends from about halfway between 50 and 52 levels to just below 48 level (see Fig. 1). The EB reefs form the lower portion of the EB zone of the Elsburg series and in the 81 line area the various conglomerate bands show the best development. Up to 18 separate reef bands are developed and the distance from the bottom conglomerate band to the top is ± 26 m. The thickness of the quartzite which forms the middling between the various reef bands varies from 0.1 to 2 m. The strike is roughly north-¬south. The reef bands are payable individually. However, owing to the steepness of the reefs and their close prox¬imity, conventional mining would prove very difficult. The nonpayable reef bands all carry varying amounts of gold and the whole area is a massive payable reef body approximately 26 m wide and 60 m high at 300 to 400 m on strike. The major structure of the area consists of a north¬-south trending syncline. The western flank of the syncline has a steep easterly dip, in places approaching the vertical. This flank cuts out against the overlying rocks of the EA zone. The latter forms a noncon¬formity with the underlying EB zone. The eastern flank of the syncline dips to the west at an average dip of 0.17 rad (10°). The 0.1 rad (6°) north-plunging syncline was sub¬jected to severe faulting. The most important are the Nos. 4 and 10 faults, both of which have a roughly north-south strike. The No. 4 fault dips to the west at an angle of 1.04 rad (60°) with a downthrow of approximately 150 m to the west. The dip of the No. 10 fault is 0.69 to 0.81 rad (40° to 50°) west, with the western block having moved 150 m updip relative to the eastern block. The EB reefs are being mined by the sublevel stoping method down from the sub-outcrop position to the cutoff against the No. 4 fault. On the downthrow side of the No. 10 fault, that is just above the 54 level, two reef bands are payable and will be mined conven¬tionally. ROCK MECHANICS From the section in Fig. 1, it can be seen that the area under consideration is surrounded by stoped-out areas. This will naturally change the stress distribution extensively. The only way to calculate the stress field for such a geometry is to use the finite element method. It was established that this method worked for the present geometry and so the method was applied to predict the stress behavior of the final geometry. From the results, it appeared that the effect of the old stopes was to destress the area. There are, however, some areas-such as the 50 and 48 north footwall haulages-which will require continuous attention. In these two footwall haulages, deterioration can take place due to tensile stress which

Jan 1, 1982

By Wolfgang Pietsch

DR iron') is a generic term for metallized product that results from the direct or solid state reduction of iron ore. In direct reduction, iron oxides are reduced to metallic iron in the solid state without an intermediate melting step. MIDREX ® Iron is the DR iron material produced in the MIDREX ® Direct Reduction Process. Except for some thermal and mechanical degradation, the external physical form of as-reduced DR iron is the same as the feed material. Chemically, oxygen associated with iron is removed leaving a very porous structure. Figure 1 is the scanning electron micrograph (SEM) of the internal surface of a MIDREX Iron pellet obtained from a Swedish oxide pellet during reduction at 760 °C. Figure 2 is the SEM of a polished and etched cross-section through the same pellet showing the amount of intraparticle porosity. As a result of this high porosity, apparent density of DR iron is relatively low, typically a¬round 2 g/cm3, and specific surface is extremely high, typically around 1.0 m2/g or more. Both density and specific surface depend on the raw materi¬al and the operating conditions of the direct reduction plant. Normally, more than 97% of the available iron is reduced into metallic iron with the rest mainly in the form of wustite (FeO). During direct reduction, the gangue in the iron remains essentially unchanged. Removal of oxygen and the corre¬sponding reduction in weight result in a slightly higher percentage gangue in the product than in the raw material.

Jan 1, 1976

By D. Van Orden, Y. Kamiya, R. Lee, E. Ilgren

Crocidolite is a well-known causative agent for mesothelioma. However, studies have shown that the pathogenicity of the fiber from different mines varies considerably and it has been postulated the parameter that appears most likely to account for this variation is fiber width although this has never been formally confirmed. To date, crocidolite appears to be the only asbestos mineral for which an epidemiological study comparing the risk of mesothelioma in a population exposed to ‘thin’ fibers with another exposed to ‘thick’ fibers of the same species may be carried out. Finnish anthophyllite, South African amosite, and African Transvaal crocidolite can also be classified as thick fibers, and there is a paucity of mesotheliomas in populations exposed to them compared to those exposed to thin Cape crocidolite. No thin occurrences of these minerals are known. Our previous study looked at crocidolite from several sources. The present study considers the amphibole anthophyllite found in many places in the world. This mineral, regardless of source, does not show the same variation in fiber width found with crocidolite from different areas. All anthophyllite fibers that have been mined may be classified as thick and populations exposed show very low levels of mesothelioma. We suggest the most likely explanation is related to the fiber width distribution and a concomitant reduction in the ‘Stanton fiber size’ fraction.

Jan 1, 2012

By Mei Long, Tawum Juvert Mbah, Jianhua Zhang, Haiwang Ye

There have been many improvements and advancements in the application of neural networks in the mining industry. In this study, two advanced deep learning neural networks called recurrent neural network (RNN) and autoregressive integrated moving average (ARIMA) were implemented in the simulation and prediction of limestone price variation. The RNN uses long shortterm memory layers (LSTM), dropout regularization, activation functions, mean square error (MSE), and the Adam optimizer to simulate the predictions. The LSTM stores previous data over time and uses it in simulating future prices based on defined parameters and algorithms. The ARIMA model is a statistical method that captures different time series based on the level, trend, and seasonality of the data. The auto ARIMA function searches for the best parameters that fit the model. Different layers and parameters are added to the model to simulate the price prediction. The performance of both network models is remarkable in terms of trend variability and factors affecting limestone price. The ARIMA model has an accuracy of 95.7% while RNN has an accuracy of 91.8%. This shows that the ARIMA model outperforms the RNN model. In addition, the time required to train the ARIMA is than that of the RNN. Predicting limestone prices may help both investors and industries in making economical and technical decisions, for example, when to invest, buy, sell, increase, and decrease production.

Jan 6, 2021

By B. P. Sullivan

This paper describes how the author projected the economic benefits of a proposed coal liquefaction project based in Pennsylvania. These benefits were assessed in a successful effort to garner government support for the project. The projections considered such issues as increases in employment, wages, and tax receipts to state and local government, plus other less-obvious benefits, such as site remediation. The paper explains how sponsors of similar projects can use economic projections in making meaningful and compelling presentations to federal, state and local authorities.

Jan 1, 2000

By O. Ofor

Coal fines of less than 0.5 mm particle size, discarded as too fine for gravity separation, were subjected to flotation tests at varying pH and temperatures using modified dosages of kerosene as oil phase and methylisobutylketone (MIBK) as frother. Optimal coal recovery of over 74% was obtained using 200 kg kerosene and 4 kg MIBK per ton of coal fines at a pH of 9.7 and an ambient temperature of 26° C. The coal concentrate obtained under these optimal recovery conditions assayed 9.10% ash, 0.35% sulfur and 0.011% phosphorus, representing reductions in the ash, sulfur and phosphorus contents of approximately 75%, 43% and 8.3%, respectively. Its gross calorific value was 32.9 MJ/kg, its percentage of volatile matter measured 30.6 and the fixed carbon content was 66.3% (d.a.f). Caking tests showed the optimal concentrate has a standard welling number of 1 and is a Gray-King coke type C. These results show that the optimal flotation product could be utilized for such industrial purposes as steam raising or for processing in gasworks, but it would be unsuitable for metallurgical coke production.

Jan 1, 1993

By R. L. Virta

Four companies ? H.C. Spinks Clay Co., Inc., Imerys, Old Hickory Clay Co., and Unimin Corp. ? mined ball clay in four states in 2013. On the basis of preliminary data, production was 1 Mt (1.1 million st) with an estimated value of $47 million. Production increased by 3 percent in tonnage from 973 kt (1.1 million st) with a value of $45.1 million in 2012. Tennessee was the leading producer accounting for 64 percent of domestic production, followed by Texas, Mississippi and Kentucky. About 67 percent of total ball clay production was airfloat, 22 percent was crude or shredded and 11 percent was water-slurried.

By S. K. Kawatra, J. A. Halt

"Low-grade iron ores are finely ground and processed to recover iron-bearing minerals. However, the iron-rich powder is too fine to be used directly in blast furnaces and most direct reduction furnaces, and must be agglomerated or pelletized into a usable product called “pellets.” Bentonite clay has traditionally been used as a binder to make iron ore concentrate pellets, but it is expensive and contaminates the pellets. Organic binders may be a viable alternative to bentonite clay. This manuscript reviews organic materials that have been used to make iron ore concentrate pellets. Included are discussions on the development of organic binders, common pros and cons to organic binder use, organic binder structure and its effects on agglomeration, and additives to organic binders.IntroductionIron ore agglomeration turns finely disseminated, low-grade iron ores into a usable product, called pellets. During pellet production, fine-grained, iron-rich minerals are liberated from low-grade ores, concentrated, and agglomerated into round balls that are thermally hardened or cold-bonded to form pellets. Pellets are then transported to blast furnaces or direct reduction operations where they are used to produce iron; iron is further refined and shaped into the wide variety of steel-based industrial and consumer products in use today.Over the years, pellet production has become increasingly more prevalent with the increased exploitation of low-grade iron ores and increased iron and steel consumption around the world. In 2010, world iron ore pellet production was 388 Mt. It could be argued that the current pellet production process has been enabled by the use of binders – practical experience has shown that it would be nearly impossible to agglomerate iron ore concentrates using rotary drums and discs without using a binder."

Jan 1, 2015

By M. Bunch

"THE SUPER CYCLE IS GONE The utopia of the rising sales volume, for mining companies from 2002-2011, was entirely due to rising production volume and prices. The Australian mining sector experienced an 18 percent annual growth rate in revenues, and 11 percent growth in prices. (1) However, EBIT remained flat during the same time period. In addition, Australian mines saw a 7 percent annual decline in both labor and capital productivity. (2) Mines in the U.S. and Canada produced similar results, whereas the world-wide mining industry has seen a productivity drop of 40% since 2001. (3) The decade “Bull Run” of rising prices was trashed by companies that chased low-quality assets while increasing debt on their balance sheet. It seemed everyone believed the “super cycle” would last forever, while completely ignoring the history of cycle downturns. Worldwide mining operations are as much as 28 percent less productive today than a decade ago, according to new McKinsey research. The results from McKinsey’s new MineLens Productivity Index (MPI), which adjusts for declining ore grades and mine cost inflation, show that the pronounced decline in productivity is evident across different commodities and is seen in most mining players and geographies. (4) McKinsey sees three important areas of focus to address the root causes of productivity decline. 1) Embed effective management operating systems at mines 2) Prioritized operational excellence and capabilities development 3) Focus on innovation Reality has now settled back in and companies are struggling to make ends meet. The basic management staple of controlling costs and improving the production/productivity that was lost in the excitement is now back in play. Traditional cost-cutting approaches, such as across-the-board spending cuts, layoffs, and hiring freezes are only short-term initiatives and will not permanently improve a company’s cost structure or improve long- term competitiveness. This can only be accomplished by engaging front-line employees and empowering them to make necessary improvements in their daily work. It is time for leaders to lead and develop cultures of continuous improvement within their organizations in order to sustain their mining project to the end of mine life. Successful operating managers require two different skill sets of Leadership and Management; knowing how to lead people in their organization and how to manage the work they do."

Jan 1, 2016

By F. B. Kuhnow

When performing blasting operations in open pit settings, energy is released and transmitted through the geology. Some negative effects can have significant impacts on mining operations and adversely affect mine production. This technical paper presents recommendations for blast design to prevent damage due to ground motion from blasting on adjacent concrete structures of underground operations. The paper includes a case study describing a problem regarding an open pit mine expansion and asks whether production blasting will damage concrete shaft structures due to blast stress waves and blastinduced ground motion. Based on the results, a set of criteria is provided to implement in current and future mining operations that involve blasting near underground concrete structures. A set of techniques on how to improve vibration levels for safe operations is also presented. Knowledge of particle velocity and wave propagation for site-specific circumstances to determine a safe level of vibration is recommended. Emphasis is placed on making use of electronic detonators and early delay detonators to achieve successful levels of vibration. A dynamic analysis is necessary to determine if vibration from blasting can damage the concrete shaft structure. When reinforced concrete structures are subject to blast loading, both concrete and steel are subject to very high strain rates. As opposed to static loads, when subject to high strain rate loads these materials increase their strength significantly. In fact, they increase by more than 50% for reinforcing steel, by more than 100% for concrete in compression, and by more than 600% for concrete in tension. This finding is of significant importance in mining operations because it allows an increase in flexural capacity of individual members as a result of high strain rates. Therefore, an elevated ground vibration (PPV) or particle velocity is permissible when blasting takes place near concrete structures.

Jan 1, 2014

By D. R. Tweeton

A modified push-pull field test and a computer model of cation exchange were developed to aid in evaluating cation exchange parameters prior to in situ mining. Reliable determination of these parameters is essential when modeling restoration of groundwater quality. The field test involves a much larger volume and much less disturbance to the ore sample than is feasible with laboratory measurements. This test can be performed in two or three weeks. It is relatively inexpensive, requiring one injection- production well and two or more wells for collecting samples of leach solution. The use of the model in interpreting test results is illustrated with field data from an in situ uranium mine. Much of the research was performed by the University of Texas at Austin, and was partially funded by the Bureau of Mines.

Jan 1, 1986

The Earth?s population is approaching 6.6 billion people. More than half live in urban areas. And, as those figures continue to grow, the need to make wise use of the world?s natural resources as well as its living space will also grow. Thus, the concept of sustainable development ? meeting the needs of the current generation while preserving resources for future generations. The use of underground space is only one part of the sustainable development concept. But it is an important one. Tunnels and underground space are environmentally friendly and contribute significantly to sustainable development. But it takes years to plan and build tunnels and other underground infrastructure. And the demand for infrastructure in the world?s mega cities has grown significantly. In December, about 100 people representing several developed and developing nations spent a day at the United Nations (UN) in New York City discussing the future of underground space development throughout the world. The meeting was put on by the UN?s Department of Economic and Social Affairs and the International Tunnelling and Underground Space Association (ITA). The conference was titled ?The Use of Underground Space as an Unexpected Solution for Promoting Sustainable Development.? Its aim was to promote practical solutions to the use of underground space and tunnels as feasible alternatives to promote sustainable development throughout the world. A panel of speakers from government, academia, the UN and the ITA stressed that development is not sustainable without infrastructure. And, as the world?s population grows, there is now an urgent requirement to efficiently plan for the use of underground space to preserve it for the future benefit of mankind. The benefits of the use of underground space are many, they said. Among them: ? Tunnels channel clean water in and waste water out. This promotes health and sustainability worldwide, particularly in developing countries. ? The use of tunnels and underground space helps conserve energy and increases its efficient use ? the use of tunnels cuts commuting time and so saves energy. ? Tunnels, microtunnels and other underground structures promote the more efficient use of space in large cities ? the bulk storage of water, fuel and other goods. ? Underground structures are subject to less stress than surface structures, making them safe havens for natural and man-made hazards, including earthquakes. And, because underground structures are more durable, lifecycle costs are less than surface structures. ? Underground structures promote the multiple use of available land. Land owner-ship at several layers increases land use and provides more usable space. Han Admiraal is director of the Center for Underground Construction in the Netherlands. He said that urban planners need a new vision concerning the use of underground space. Going underground protects historical and archaeological surface facilities, he said. Underground space use can also protect populations located in adverse climates. And sensitive environmental areas on the surface can also be protected from development. In addition to the transportation of people, freight and water, underground development can also store water, as well as provide storage for waste, hazardous materials, carbon dioxide and geothermal energy. The upshot of this new awareness and vision for under-ground space is that its use should be considered before surface development, Admiraal said. And planners and developers are placing more emphasis on underground space development as part of their overall development plans for urban areas. That was not always the case, he said. In the past, underground space was not considered until after the surface space had run out, he said.

Jan 1, 2008

By W. K. Katoto

The Tailings Leach Plant (TLP) of the Zambia Consolidated Copper Mines Ltd at Nchanga was commissioned in 1974 as the world's first largest successfully operated agitation leach SX-EW plant for copper production. The design, development and operation of the plant soon after commissioning termed as TLP stage II has been described by Holmes et al (1). In the initial phase the plant was designed to treat approximately 25,000 tonnes per day of current flotation tailings from the Nchanga Concentrator operations, and had a design capacity to produce 75,000 tonnes per annum of copper. Further expansion took place in 1986, and TLP stage III was successfully commissioned to treat an additional 20,000 -25,000 tonnes per day of large reserves (over 135m tonnes) of reclaimed tailings stockpiled since the early 1930's in four paddock type tailings dams (T01 to T04). The salient feature of TLP stage III expansion described by S K Mwenechanya et al (2 -3) was the installation of the world's largest Horizontal Belt Filter Plant with 26 filters each of 80 m2 filtration area.

Jan 1, 1996

By V. K. Gupta

The phenomenon of zero order production of fines associated with the batch comminution of monosize feeds in tumbling mills has been examined in the context of the size discretized population balance model. It has been shown that the model admits zero order production kinetics only in an approximate sense. The necessary and sufficient conditions for approximate zero order production of fines have been obtained. As these conditions cannot be expressed in terms of the model parameters Sj and Bi,j alone,. several examples have been used to illustrate some of the important characteristics of the zero order production systems. One of the important characteristics of these systems has been identified as a "weak necessary condition", and the other as a " favourable condition ".

Jan 1, 1985

By G. L. Smit

The Buffelsfontein Gold Mining Company is situated in the Klerks-dorp district of the Province of the Transvaal in the Republic of South Africa, approximately 100 miles west of Johannesburg. Gold production commenced in January 1957 and Uranium treatment of residue slimes as a by-product started in July 1957. The mining property is 5435 mining claims in extent, the equivalent of 7,988 acres or 12.5 square miles. The mine was initially exploited by the Pioneer Twin Shaft System, consisting of a 26 feet diameter down-cast shaft and a 22 feet diameter up-cast shaft, sunk in the north-west area of the mine to cater for the hoisting and ventilation requirements for a milling rate of 150,000 tons per month.

Jan 1, 1964

By Rudrajit Mitra, Erik Hulthén, TOBIAS HARTMANN, ELISABETH CLAUSEN, Aarti Sörensen

There has been an ongoing debate on how to transform engineering education to better prepare students for today`s professional world that is characterized by increasingly complex problems and challenges that engineers are tasked with upon entering the industry. Within the conceive–design–implement–operate (CDIO) framework, entrepreneurship education presents a valuable pedagogical approach to foster the necessary skills of the students through integrated, hands-on, active learning experiences. While numerous publications have addressed possibilities of how experiential, problem-based, project-based and active learning can be integrated into engineering curriculum, there has been hardly any attention on mining engineering with respect to adopting this approach. This paper will address the possibilities of integrating entrepreneurship education into mining engineering programs in particular. This paper will enhance and foster discussion among academics from mining engineering on how to integrate elements of entrepreneurship education on a course, program and departmental level to infuse value creation experiences across the curriculum.

May 25, 2022

By Jürgen Kretschmann, Christina Suarez, Jürgen Brune, Stefan Möllerherm

"The Ruhr region in Germany’s North-Rhine Westphalia is going through significant change. By the end of 2018, the last two underground hard coal mines in the Ruhr, Ibbenbüren and Prosper-Haniel collieries, will close their portals and bring an end to more than 200 years of coal mining and an industry that was once the economic and cultural backbone of the area. Ruhr is undergoing an impressive economic and cultural transformation, as it gradually shifts from being a region once dependent on coal and steelmaking to a post-mining region focused on redesigning itself as a cultural center. This article focuses on the socioeconomic impacts of the transformation into post-mining and the roles of the government, labor unions and local community to aid the transformation from the perspective of an American student. It will look into the cultural values that are helping to drive the transformation and compare them to American standards and values in order to determine if a similar approach can be used in the United States and its coal industry. History and backgroundUnderground hard coal mining has had a long history and a significant impact on the culture and economy in Ruhr since the early 19th 20century. The Ruhr region is located in the heart of the German state of North- Rhine Westphalia. Ruhr is bounded by the Rhine River in the west, the Ruhr River in the south and the Lippe River in the north, with the Emscher River running through its center.The Ruhr is home to around 5.1 million people and spans an area of approximately 4,500 km2 (1,730 sq miles). Before the era of industrialization, the Ruhr was a rural, agricultural region. Small-scale coal mining began in the 13th century, with coal being used for heating, cooking and metallurgical processes, including steelmaking. With 19th-century industrialization, coal mining became a significant driver of the region’s economic structure. Steam engines, and soon, electric motors, allowed for the pumping of mine water and for powerful hoists hauling from deep shafts, enabling miners to reach deeper coal seams that were once thought impossible to mine. The Ruhr mining boom began in the 1850s, supported by Prussian economic policies that attracted many workers and their families to the region. The population grew from 400,000 in 1850 to 5.7 million in 1957. The coal and steel industries were key contributors to Germany’s “Wirtschaftswunder” — or “miraculous economic recovery”— in the 1950s. In 1956, the coal industry reached its peak production of around 112 Mt/a (124 million stpy) of coal and employed almost 600,000 miners."

Mar 1, 2019

By Swades Kumar Chaulya, Vikash Kumar, Sushma Kumari, Naresh Kumar, Girendra Mohan Prasad, Monika Choudhary

Opencast mines are vulnerable to inclement weather conditions as it disrupts the day-to-day activities at these mines. To address the problem, a perceptive driving assistant system (PDAS) has been developed to increase the visibility of real-time video of the road in front of the vehicle for operators of heavy earth-moving machinery (HEMM) at opencast mines in harsh weather conditions.

Apr 1, 2023

By Michael Day, Paul Kos, Scott Brinton

A hydrogeologic characterization and impact analysis was performed for a proposed quarry at the Hitch Rack Ranch located in the Little Turkey Creek watershed southwest of Colorado Springs, Colorado. Continuous multiple channel tubing, nested piezometers, stream flow measurements, and mapping of known seeps were used to define the three-dimensional potentiometric distribution and areas of groundwater recharge and discharge. Water balance considerations, mass balance calculations, and potentiometric response to earth tides and barometric fluctuations confirmed that the granite fracture system in the ridge area of the proposed quarry has an extremely low bulk hydraulic conductivity resulting in minimal groundwater discharge to sustain the baseflow of Little Turkey Creek. The Little Turkey Creek valley forms the major conduit for groundwater flow exiting from the upper part of watershed underlain by granite. This conclusion has significant implications with respect to mine planning to minimize projected impacts to the hydrologic system and preserve this recharge component to downgradient Denver Basin sedimentary deposits.

By Silas Li, Michael Harris-Gifford, Jason Choi, William H. Hansmire

Twin-bore tunnels with a single track in each tunnel are currently the most common subway tunnel configuration. However, a large diameter single-bore tunnel with two tracks separated by a center wall could replace twin-bore tunnels and introduce potential benefits but require necessary modifications to the subway system. In particular, a nominal 40-foot-diameter single-bore tunnel can be considered in lieu of nominal 20-foot-diameter twin-bore tunnels. This paper discusses the benefits and modifications introduced by replacing twin-bore tunnels with a single-bore tunnel, with respect to various elements of the subway related to the tunnel, stations, track, and tunnel systems.

Dec 1, 2022