Search Documents

By M. Görnerup, A. Kapilashrami, Seetharaman. S., A. K. Lahiri

Simultaneous reduction and foaming of chromium-rich slag have been studied in a laboratory furnace equipped with X-ray image analysis. Reduction of the metal oxides by graphite generated CO, which caused the melt to foam. The slag composition continuously changed due to reactions and dissolution of lining. Gas generation rate, foam height, and gas bubble size were studied and correlated to slag composition. Viscosity increased significantly during the experiments due to a change in slag composition. Bubble sizes varied little during the progress of reactions but differed considerably for different slags. Bubble sizes were largest for V2O5 containing slag, which is contrary to the general understanding that the presence of strong surface active agents reduces the bubble size. The foaming index did not follow expected trends for bubble size and viscosity, suggesting that foaming index is not a suitable parameter for discussion of foams under dynamic conditions. Keywords: slag, foaming, dynamic conditions

Jan 1, 2004

This paper reviews ore pass practice in some Canadian mines in Quebec and Ontario. In particular it reviews ore pass configuration, flow control mechanisms and monitoring practice. A review of the type of problems encountered and the tools to restore flow is also presented.

Jan 1, 2005

By A. M. Milev

A simulated rockburst was conducted underground at Kopanang Mine, previously called Vaal Reefs No. 9 Shaft. The rockburst was simulated by means of a large blast detonated in solid rock close to a crosscut sidewall. The simulated rockburst involved the design of the seismic source, seismic observations in the near and far field, high-speed video filming, a study of rock mass conditions such as fractures, joints, rock strength etc. Knowledge of the site conditions before and after the simulated rockburst was also gained. Some of the important findings are listed below: ?Two areas of damage were identified on the blasting wall: (i) an area of high-intensity damage in which ground velocities of 3.3 m/s were recorded by an accelerometer, which was subsequently ejected in a block of rock, (ii) an area of low-intensity damage where ground velocities of 1.6 m/s were recorded by an accelerometer which remained on the tunnel wall. ?High-speed filming revealed rock fragments being ejected from the wall at velocities in the range of 0.6 m/s to 2.5 m/s. The measurements were taken in the area of low-intensity damage. As planned, no gas pressure was directly involved in damaging the wall of the tunnel. ?The attenuation of peak particle velocities for the main blast in the near field (6 m to 30 m), as a function of distance R, was found to be proportional to R-1.7. ?The simulated rockburst was recorded as a local magnitude ML= 1.3 by the Klerksdorp regional seismic network. ?Peak particle velocities from nearby blasting, recorded on the tunnel wall after the simulated rockburst, were about six times greater then peak particle velocities recorded from the same source area before the simulated rockburst.

Jan 1, 2001

By J. Martinovic

The large proportion of gangue minerals present in platinum bearing ores in South Africa provides challenges to the flotation and downstream processes. In order to take effective measures to reduce their recovery in flotation, an understanding of the mechanisms and factors influencing their behaviour is needed. Typical gangue minerals are pyroxene, feldspar, quartz, chromite and talc. Of these, talc is a naturally hydrophobic mineral and although it is present in relatively small quantities, it has a disproportionate effect as it has a strong froth stabilizing effect, increasing the recovery of other gangue minerals by entrainment. Talc recovery is effectively reduced with the addition of polymeric depressants. Although the other gangue minerals are assumed to be hydrophilic and their recovery by entrainment is expected to follow the water recovery, there is some evidence that they may be activated by the typical reagent suites used. Reagents such as copper sulphate, added as an activator, and collectors are used to selectively induce hydrophobicity on the sulphides. It has been shown that some of these gangue minerals can be activated. This research work investigates whether inadvertent copper activation is mineral specific and evaluates the mechanisms and factors affecting the reversal of activation with the addition of the depressants using electrokinetic measurements, adsorption and microflotation tests. Results are presented that show that the selected minerals do respond differently and that the reversal of activation is dependent on mineral type, depressant type, dosage and ionic strength of the electrolyte.

Jan 1, 2005

By H. G. Oltmann

The equilibrium nitrogen solubility in the CaO-SiO2system was studied by a slag-gas equilibration technique, in graphite crucibles at 1823K under a CO-N2 atmosphere. The nitrogen content of the slags was determined by the Kjeldahl method. A reliable technique was used to obtain an initial nitrogen content in the master slags, from the addition and pre-melting of silicon nitride. Reduction of silica by graphite was found to occur during the equilibration experiments, resulting in compositional changes of the slags. The results were extrapolated to equilibrium by kinetic evaluation of the data. The nitrogen solubility showed good agreement with the result of Suito and Sano, while Fruehan?s results were lower. However, the results of the present study do not support the maximum nitrogen solubility values found by Sano.

Jan 1, 1999

The Gordonsville Operation of Pasminco US Inc. along with the Center for Advanced Mineral and Metallurgical Processing (CAMP) at Montana Tech studied, developed and implemented a pilot-scale hydrometallurgical facility for the industrial recovery of germanium and gallium. This paper describes the joint testing and engineering programme that culminated in this successful process.

Jan 1, 2008

By G. Wendel

Uranium is a naturally occurring radioactive material in the earth?s crust. Geological processes have resulted in concentration of uranium into ore mined for its gold content in South Africa. This uranium is present in the form of discrete particles of uranium minerals, generally oxides, which are normally insoluble. Chemical and physical processes during gold mining and extraction, particularly when carried out in conjunction with uranium extraction and sulphuric acid manufacture, act on the uranium minerals and the radioactive decay products of uranium. This may result insignificant accumulations of radioactive materials in certain parts of the process. There are a number of naturally occurring radioactive materials in the earth?s crust, such as Uranium-235, Thorium-232, andPotassium-40. This paper focuses on Uranium-238, together with its decay products, and how they affect the gold mines. Water plays a significant role in the redistribution of radionuclides, both as a physical transport medium, and as a solvent in which chemical reactions take place.

Jan 1, 1998

By A. Hiltunen, R. Hiltunen

The utilization of blast furnace and BOF slags has long traditions and well-known applications in the building and road construction industries and in soil conditioning. The starting point for product development has been the basic physico-chemical properties of slags. This development has led to the almost 100% utilization of blast furnace slags and also considerable amounts of steel slags. While new methods and applications are continuously being looked for and developed in order to recycle and utilize all types of slag, there is at the same time an increasing debate over the exact nature of the slags, whether they are products or waste material, and whether they should be considered substances or preparations. These questions have emerged as a consequence of the environmental effects of the slags and current environmental legislation. The environmental effects of slags can be seen to be both beneficial and less beneficial. There is no doubt about their benefits in the road construction industry, as they allow significant savings in terms of natural materials and in transportation. It is also a known fact that using slags as fertilizers and in the cement industry leads to reduction in CO2emissions. The less favourable effects are the possible harmful emissions into the soil and groundwater. In this paper we describe the properties of slag products and their environmental effects according to investigations carried out in Finland. Keywords: utilization, blast furnace slag, steel slag, properties, solubility, environment

Jan 1, 2004

By J. Ekengård, H. Srinath, M. Andersson, P. Jönsson, D. S. Sarma

The present paper deals with mixing between the metal and slag phase during the ladle refining process, including vacuum degassing. Dispersion of metal drops in ladle slags has been studied. The results show a larger quantity of metal droplets in ladle slag during the alloying and stirring phase than during the subsequent vacuum degassing phase. The thermodynamic and kinetic aspects of the interaction between metal drops and the slag matrix have been considered and probable reasons for the observed distribution discussed.

Jan 1, 2004

By A. Z. Toper

This is a sampling of the papers presented at the conference, the proceedings can be bought from the SAIMM An extensive research programme to address the issue of rockburst control has been undertaken over a number of years. This paper discusses the development of preconditioning techniques to control face bursts, for safer mining in seismically hazardous areas. Preconditioning involves regularly setting off carefully tailored blasts in the fractured rock immediately ahead of a mining face, so as to encourage slip on pre-existing fractures, in order not to allow the accumulation of high strain energy density in the rock mass. Two different preconditioning techniques have been developed, namely face-perpendicular preconditioning and face-parallel preconditioning. Both have prevented face bursting in areas to which they have been applied, even though several large seismic events have occurred close to the faces in some areas. In addition, minimal overall damage was observed in the preconditioned panels following these events, compared to similarly exposed unpreconditioned panels. Preconditioning has also provided some protection to the face area from distant events, through the capacity of the preconditioned ground to absorb energy. An improvement in hangingwall stability and productivity has also been noted in preconditioned areas. In order to determine the optimum blast parameters for achieving the most effective preconditioning, an extensive optimization study was carried out for the face-perpendicular preconditioning technique. While optimum values for parameters such as hole length, diameter and spacing were determined, it was ultimately concluded that the differences in results obtained by varying the preconditioning parameters were less significant than the clear positive differences observed when comparing preconditioned areas with non-preconditioned areas.

Jan 1, 2000

The unpaved road network on a surface mine is extensive, comprising numerous roads of varying construction and material qualities with highly variable traffic volumes. Existing haul road maintenance management systems (MMS) work well for predictable traffic volumes, but for complex mine road networks, the MMS becomes onerous. This results in sub-optimal road maintenance strategies with the attendant increase in total road-user costs and reduction in service. A real-time maintenance management system was thus sought to overcome the deficiencies of existing MMS for mine roads. Since most large mines operate trucks with on-board diagnostic data collation, linked through a centralized communication and GPS backbone, it was proposed that road condition could be monitored on a real-time basis through on-board vibration signature analysis. The aim of this paper is to present the development of a real-time mine haul road maintenance management system. Following are view of mine road maintenance practices, the real-time system architecture is introduced and the results of a field trial of on-board vibration signature assessment is presented. The trial results are discussed in the light of road defect signature recognition, analysis, signature repeatability and system limitations. This approach has applicability to other situations such as a network of district roads, subject to an analysis of the economic feasibility. The paper concludes that modern technology has the potential to apply maintenance as and where needed with possible reductions in authority cost and an improvement in service provided for the road user.

Jan 1, 2003

The results of a series of physical model studies of the stability of jointed rock slopes carried out some years ago are described. These models were tested under centrifugal loading. Four ?geological? structures were tested; all had the same joint orientations and strengths, but the relative spacing of the joints was different. The results showed that the mechanisms of failure of the slopes varied for the different models, and the gravitational loads at which failure developed also varied. The following conclusions are drawn from the results of the physical model tests: ?the mechanism of slope failure is by progressive deformations throughout the slope ?the ratio of the spacings between the different sets of discontinuities exerts considerable influence on the slope failure ?in the models tested, the intact material strength had no noticeable influence on the stability of the jointed rock slopes(note that for hard rock, similitude conditions indicate a prototype slope height of 300 to 400 m, and therefore intact rock failure might not be expected under simple gravity conditions, i.e. no tectonic stresses) ?rock slope failures are three-dimensional and in general are not amenable to two-dimensional simplification ?knowledge of the orientations of discontinuities in the slopes does not allow prediction of a unique failure surface, nor of a volume of failure. The volume of failure is determined to a large extent by the plan configuration of the slope.

Jan 1, 2006

By L. Bircumshaw

Paper written on project work carried out in partial fulfilment of BSc (Eng) (Chemical) degree This paper details the formulation of a mathematical model for the simulation of a primary bioleach reactor, with specific reference to the leaching of pyrite. The model is based on the direct reaction mechanism, where the leaching of pyrite is said to occur via a two-step process. The process involves the formation of ferrous?iron through the chemical leaching of pyrite and subsequent bacterial oxidation of ferrous-iron back into ferric-iron. At steady state the rate of chemical leaching and bacterial oxidation are linked by the ratio of ferrous-iron to ferric-iron in solution. The extent of conversion of pyrite in the reactor system is described using the segregated flow model, with the exit age distribution of the solid phase being described by the Tanks-in-Series model. The final phase in model formulation involves the inclusion of steady state material balances on the bacteria and fluid phase components. The model is compared to pilot plant data and laboratory data for two different types of pyrite concentrates, with simulation results showing that the model is in good agreement with the data. Author key words: Bioleaching; pyrite; primary reactor; modeling; segregated-flow model; tanks-in series model.

Jan 1, 2006

By M. A. Amarante

Beneficiation studies were conducted on a Portuguese feldspar ore, in order to obtain final products capable of being used in the ceramic industry. A simple scrubbing operation is enough to break the lumps in the feed. The ore deposit contains ca 35 x 106tonnesfrom which, by screening, three main products could be obtained. This paper focuses on the beneficiation of the 500/74 µm fraction, which constitutes about 27% of the ore, assaying 9.42% Al2O3,equivalent to approximately ca 46% feldspar, with a mean iron content of 0.29% iron oxides. Magnetic separation and froth flotation testwork was carried out, in order to decrease the iron contamination and increase the feldspar content. Magnetic separation alone decreased the iron content of the feed to values between 0.04 and 0.08% iron oxides with an average yield greater than 90%. Flotation with HF, provided a feldspar recovery of 45?46% with a concentrate assaying 17.6% Al2O3. The use of H2SO4, gave a recovery of 35?36% of feldspar concentrate, assaying 16.1% Al2O3. However, economic and environmental advantages of using sulphuric acid may compensate for the lower mass recovery. The iron content of0.12% iron oxides in these concentrates, could be reduced to 0.04?0.05%, by further magnetic separation.

Jan 1, 1997

The corrosion behaviour of a low carbon steel was investigated in natural seawater and various synthetic seawaters. It was found that the steel corroded nearly four times faster in a 3.5% NaCl solution than in natural seawater for an exposure time of 21 days. The corrosion rate after immersion in synthetic seawaters (ASTM D1141 and Marine Biological Laboratory seawater) is similar to the corrosion rate after immersion in natural seawater. Calcium carbonate (aragonite) deposits were found on the surface of the steel after immersion in natural seawater and the synthetic seawaters. Some magnesium-containing deposits were also found after immersion in the natural seawater. These deposits act as a barrier against oxygen diffusion and thereby lower the corrosion rate. The morphology of the calcium carbonate deposits that formed during immersion in the natural seawater is different from those formed during immersion in the synthetic seawaters. This may explain the slightly lower corrosion rates obtained in the natural seawater. X-ray diffraction also showed that the oxy-hydroxides formed in the 3.5% NaCl solution differed from those formed in the other solutions. Keywords: Corrosion, seawater, low carbon steel, 3.5% NaCl, aragonite

Jan 1, 2006

By C. Daly

The Faculty of Engineering at the University of New South Wales (UNSW) offers a core first-year engineering design and innovation course, ENGG1000, undertaken during the first and second semesters. This course is highly regarded in the sense that it provides an introduction to many concepts and activities that students will experience over the four-year minimum for which they are undergraduates at UNSW. Approximately 1400 students enrol in the semester 1 course across the Faculty, typically 80 of which undertake the Mining Engineering stream. Students in teams of between six and eight design and construct a physical model to represent an aspect of their chosen discipline. For example, in 2013 the mining engineers designed and built a model dragline. This paper concentrates a major aspect of the course ? the involvement of team members in group activities and the development of the associated skills of peer assessment and peer review as the course progresses over a period of 12 weeks. The term ?peer assessment? in this paper refers to the requirement for students to assess the design components of their peers. This course has a structured requirement in terms of how a successful design is a result of a sound design process rather than a ?try and see? approach. Each student must describe in detail the process they undertook to achieve their final design ? hence the approach is independent of the discipline and/or project selected. Peer review is a process whereby students review the contribution of their team members to the overall design. This activity encourages team involvement and interaction. The final assessment mark can be moderated by the outcome of this peer review, although it is run twice during the semester. The first ?run? is for feedback only during week six and hence no moderation is undertaken. It was found through consultation with students and from questionnaires that both processes are well accepted and highly regarded by students, as they give them a degree of ownership of the assessment process. In addition, the processes provide rapid and relevant feedback on the progress of individual students. Peer review and peer assessment are also considered to be very valuable tools for use in courses in succeeding years. For instance, many of the courses in mining engineering rely heavily on group assessment tasks.

Jan 1, 2014

By C. Daly

"The Faculty of Engineering at the University of New South Wales (UNSW) offers a core first-year engineering design and innovation course,ENGG1000, undertaken during the first and second semesters. This course is highly regarded in the sense that it provides an introduction to many concepts and activities that students will experience over the four-year minimum for which they are undergraduates at UNSW. Approximately 1400 students enrol in the semester 1 course across the Faculty, typically 80 of which undertake the Mining Engineering stream. Students in teams of between six and eight design and construct a physical model to represent an aspect of their chosen discipline. For example, in 2013 the mining engineers designed and built a model dragline. This paper concentrates a major aspect of the course - the involvement of team members in group activities and the development of the associated skills of peer assessment and peer review as the course progresses over a period of 12 weeks.The term ‘peer assessment’ in this paper refers to the requirement for students to assess the design components of their peers. This course has a structured requirement in terms of how a successful design is a result of a sound design process rather than a ‘try and see’ approach. Each student must describe in detail the process they undertook to achieve their final design - hence the approach is independent of the discipline and/or project selected.Peer review is a process whereby students review the contribution of their team members to the overall design. This activity encourages team involvement and interaction. The final assessment mark can be moderated by the outcome of this peer review, although it is run twice during the semester. The first ‘run’ is for feedback only during week six and hence no moderation is undertaken.It was found through consultation with students and from questionnaires that both processes are well accepted and highly regarded by students, as they give them a degree of ownership of the assessment process. In addition, the processes provide rapid and relevant feedback on the progress of individual students.Peer review and peer assessment are also considered to be very valuable tools for use in courses in succeeding years. For instance, many of the courses in mining engineering rely heavily on group assessment tasks."

Jan 1, 2014

By S. Achilleoudes

This paper describes the various factors that contribute to the maximum design pressures acting on box fronts and how these factors influence the mass and economy of box front steelwork. The influence of material density, rock size and moisture content on the incidence of hang ups and mud rushes in the rock pass is also highlighted. The loads acting on any box front are a function of several different parameters. These include natural, operational and excavational parameters. A case study analysis was carried out using UG2 ore and a typical box front structure to demonstrate the relationship between the mass of the box front and the material pressures resulting from variations in the above parameters. Based on the results of this case study, the required design mass of a side mounted box front for a rock pass containing platinumUG2 increases in (close to) linear proportion to % overbreak and is also linearly proportional to the pressure on the face of the box front beyond saturated conditions. The mass of the box front structure also doubles with a 100%increase in over-break which emphasises that a box hole excavation that is as neat as possible will yield a lighter and more econimical box front structure.

Jan 1, 2005

By L. Bbosa

Paper written on project work carried out in partial fulfilment of BSc (Hons) (Eng) (Mechanical) degree Discrete element methods (DEM) are being used to provide detailed impact histories of the particles in comminution devices, such as mills. To match this immense detail of information, far more informative breakage tests than those that are generally conducted are now required. The split Hopkinson pressure bar apparatus is used in this study, as it allows the calculation of breakage forces and absorbed energies. The geometry of rock particles has been identified as significant, so this project undertook to identify the influence of shape on the breakage pattern of blue stone. Comparisons are then made between the breakage pattern of angular rocks and rounded, milled rocks for single impact fracture and consecutive impact loading at low energy. Results of this experiment indicate that although breakage for both geometries occurs over a similar energy range, rounded particles have the greater probability of fracture because they absorb more of the impact energy for a given loading. Size distributions of progeny show that five pebbles or more are sufficient to predict the distribution of most particles in small energy regimes. Cumulative impact testing shows that considerably more energy is required to break a rock through cumulative damage than through a single impact?this is of considerable importance in the light of the indications from DEM simulations that most breakage in a mill will be from cumulative damage rather than single impact breakage.

Jan 1, 2006

By E. Swart

The purpose of this paper is to provide an overview of the current legislative framework for mine closure within South Africa as well as the new requirements in terms of the Mineral and Petroleum Resources Development Act, 2002. The roles and responsibilities of Government, the mining industry and other stakeholders and confusion caused are also highlighted.

Jan 1, 2003