Search Documents

By L. A. Jordan, D. van Vuuren

A two-dimensional finite difference model has been developed to describe the reduction of kilogram quantities of dehydrated phosphogypsum. The model’s scope has been limited to focus on the heat transfer and reactions that occur within a mass of material contained in a vessel inside a furnace rather than also including the effects of heat transfer to the vessel. Changes in the heat transfer properties (k, ρ, and Cp) are incorporated as the composition of the mass changes as the chemical reactions progress. The model is validated against experimental data, with samples heated to 1000°C at 3°C min−1 while purging with nitrogen gas. A sensitivity analysis of model predictions to the pre-exponential factor of the reaction rate constant of the main chemical reaction and the thermal conductivity of the powder bed indicated that, at the envisaged process conditions, the behaviour of the system depends much more on the rate of heat transfer than on the rate of the chemical reaction. The model demonstrated a significant increase in accuracy when the thermal conductivity was modelled to increase linearly with temperature compared to assuming a constant value.

Oct 1, 2022

By E. M. Sacris

The semi-autogenous grinding mill is the bottleneck whenever treating hard and finely fragmented ore at Benguet Corporation's Kaline Concentrator. Low milling rates result from very high and fluctuating mill power draw. Attempts to use a mill horsepower control loop to regulate feed rate were unsuccessful because of operational upsets caused by fluctuations in feed rate on downstream operations. The objective of the computer control was to maximize tonnage throughput by stabilizing the power draw at a high but safe level without upsetting subsequent operations. The semi-autogenous mill is operated in closed circuit with a stationary screen. Instrumentation consists of a feed weightometer, a power transmitter to measure mill load, a headwater flowmeter and an ultrasonic level sensor to measure the mill discharge sump level. A 64 k-byte FOX-3 Foxboro computer processes field data from various sensors and manipulates the input control variables. These variables are the fresh feed rate and the headwater flowrate. Feed rate is controlled through a supervisor-type computer program aimed at maximizing and stabilizing power draw. The control scheme was according to how the operators responded during an operator-directed automatic control mode. Mill dilution is similarly controlled. Results achieved reflect a 3% increase in tonnage milled because of the reduction in control variability that ensued.

Jan 1, 1987

By E. Isokangas

A mine is essentially a series of operations, including drilling and blasting, crushing, milling, flotation, and leaching, that are interconnected and therefore interrelated, with the performance of one operation affecting the performance of another. Optimizing each stage separately without considering the whole system often causes potential economic benefits and energy savings to be missed. However, the PIO methodology is a thorough approach which considers these individual process activities within the context of the whole process. The basic principle is to optimize the process as a whole, rather than each process step in isolation from the others. Metso?s Process Technology and Innovation (PTI) group offers a global consulting service for the mining and construction industries. A significant amount of this consulting work involves process integration and optimization (PIO) studies. When conducting a PIO study, every aspect of the process is considered. In addition to drilling and blasting, transportation, handling and storage, crushing, screening, grinding, flotation, separation, and recovery, other aspects including equipment utilization and energy consumption and even greenhouse gas emissions are also included if necessary. In a PIO project, it is very important to understand what type of material is being processed at any point in time. That is, which domain or domains is the material part of? This is necessary in order to observe the effect of different ore sources (and the blending of sources) on concentrator performance. Linking the ore from the pit to the concentrator required the development of an ore tracking system. As a result, PTI developed a radio-frequency based material tracking system called SmartTag?. This system allows tracking of ore from its source through blasting, run-of-mine (ROM) pads, crushers, intermediate stockpiles, and finally into the concentrator. Using the SmartTag? system, definitive correlations can be made between the performance of the plant and the plant feed characteristics, including the domain from which the feed ore originated. Since its commercialization in 2007, SmartTag? has been used in the majority of PTI?s consulting projects and several permanent systems have been installed worldwide1. Successful applications of the SmartTag? system have encouraged development to allow the system to be used in a wider variety of plants, in particular plants with finer crushing and screening stages. This paper describes how the SmartTag? system is being utilized by PTI and the benefits being gained by its use in PIO projects, as well as presenting some case studies.

Jan 1, 2012

By T. Z. Sehume, J. R. Bunt, J. C. van Dyk, C. A. Strydom

"SynopsisCo-pyrolysis of four biomass samples (hardwood chip, softwood chip, pinewood chip, and sugarcane bagasse) with an inertinite-rich medium rank C South African coal was investigated. Proximate and ultimate analyses of the chars prepared using a heating rate of 10°C/min up to 1100°C in a nitrogen atmosphere were used to compare the properties of the biomass and the coal chars. Similar gross calorific values (28.5–29.1 MJ/kg) for the woody biomass-coal blended chars were observed, which were slightly higher than that of the coal char sample (26.5 MJ/kg). CO2 surface areas of the chars of the woody biomass samples (328.1–329.4 m2/g) and of the blends (238.5–271.5 m2/g) were higher than that of the coal char sample (94.2 m2/g). Thermogravimetric (TG), differential thermal analyses (DTG), and calculated weighted averaged TG curves indicated that the influence of the biomass on the pyrolysis rate of the coal is small and vice versa. The CO2-producing reactions of the coal were slightly enhanced during co-pyrolysis.IntroductionCoal utilization has led to rising concerns about adverse impacts on the environment (global warming) caused by toxic gases (H2S, SOx, NOx, and CO2) and remaining waste. Biomass is considered to be CO2-neutral with regard to the greenhouse gas balance, and is regarded as a renewable source that assists in reducing CO2 emissions when compared with coal (McGowan, 1991; McKendry, 2002). Biomass currently makes up approximately 14% of the world’s energy sources (McGowan, 1991; McKendry, 2002). Coal combustion and gasification are prominent processes in South Africa (in producing synthesis gas and energy) due to the abundance of coal in the country. Some of South Africa’s coal resources are, however, high in ash content and also are inertinite-rich, which renders them more difficult to use industrially than vitrinite-rich low-ash coal (Jeffrey, 2005; Strydom et al., 2011). There is a need to investigate the properties and behaviour of the inertinite-rich high-ash South African coals and especially their interaction with local biomass sources. The gasification process occurs through various stages, of which pyrolysis of the char residue forms an integral part (Bunt and Waanders, 2009). Currently, particular interest is shown in the co-utilization of coal and biomass to produce synthesis gas via the gasification process (Usón et al., 2010; McGowan, 1991; McKendry, 2002). Investigating the co-pyrolysis of the South African coal and local biomass material is thus the first step in evaluating the use of local biomass sources for co-gasification purposes."

Jan 1, 2015

By V. Maseko, C. Musingwini

"When considered collectively, Mineral Resources and Mineral Reserves are arguably a key asset for any mining company. Mineral Reserves are the economically mineable portions of Mineral Resources. They therefore provide a good indication of the economic prospects in the short to medium term and associated non-financial impairments for mining companies, hence a focus on Mineral Reserves. An assessment of modifying factors for converting Mineral Resources to Mineral Reserves revealed that Mineral Reserves were most sensitive to long-term commodity prices, hence the focus on long-term commodity prices. The justification for selecting gold and platinum mines is that they collectively make a significant contribution to South Africa’s earnings from mining.The introduction of the South African Code for the Reporting of Exploration Results, Mineral Resources and Mineral Reserves (SAMREC Code) in 2000 informed the basis for analysing long-term commodity price assumptions for major South African gold and platinum mining companies between 2000 and 2016. The analysis revealed that the least number of non-financial impairments occurred when long-term commodity prices were within ±5% of spot prices. This finding suggests that this range is the ideal range for long-term commodity price assumptions to improve confidence in Mineral Reserve declarations and minimize impairments. Introduction The South African Code for the Reporting of Exploration Results, Mineral Resources and Mineral Reserves (SAMREC Code) defines a Mineral Resource as ‘a concentration or occurrence of solid material of economic interest in or on the Earth’s crust in such form, grade or quality and quantity that there are reasonable prospects for eventual economic extraction’ (SAMREC, 2016, p. 18). Mineral Resources are categorized according to increasing levels of geoscientific confidence or knowledge, from Inferred to Indicated and lastly, Measured categories. The SAMREC Code defines a Mineral Reserve as ‘the economically mineable part of a Measured and/or Indicated Mineral Resource’ (SAMREC, 2016, p. 25). In some of the other reporting codes such as the Australasian Code for Reporting of Exploration Results, Mineral Resources and Ore Reserves (the JORC Code), a Mineral Reserve is synonymous with an Ore Reserve. The conversion of Mineral Resources to Mineral Reserves involves applying modifying factors, which are non-resource considerations. The modifying factors used in the Mineral Reserve estimation process include mining, metallurgical, processing, infrastructure, economic, marketing, legal, environmental, social, and governmental factors. Each of these modifying factors consists of several components which require due consideration in the estimation of Mineral Reserves. Table I shows some of the components typically considered for each of the modifying factors."

Mar 1, 2019

By C. A. Snyders

This paper investigates the recovery of platinum group metals (PGMs) from a dilute cyanide leach solution containing base metals, in a manner similar to that used for gold extraction in a typical CIP process, and focuses on both the adsorption and elution stages. The carrier-phase extraction of precious metals using activated carbon offers significant advantages over other processes in terms of simplicity, the high pre-concentration factor, rapid phase separation, and relatively low capital and operating costs. As a sorbent, activated carbon is still by far the most important material because of its large surface area, high adsorption capacity, porous structure, negligible environmental toxicity, low cost, and high purity standards. Adsorption tests were performed on a pregnant alkaline leach solution (0.15 ppm Pt, 0.38 ppm Pd, 0.1 ppm Au) resulting from cyanide extraction performed in column leach tests. The initial adsorption rates of platinum, palladium, and gold were very fast and recoveries of these three metals were approximately 90 per cent after 2 hours and 100 per cent, 97.4 per cent, and 99.9 per cent respectively after 72 hours. The parameters that influence the extraction of PGMs and Au were examined to assess their relative importance during the adsorption process in order to provide the basis for process optimization. The concentration of thiocyanate was not identified as significant factor for PGMs adsorption, while nickel concentration was the most significant extraction process parameter. Base metal cyanide complexes adsorb and compete with the PGM complexes for sites on activated carbon, and while copper adsorption can be minimized by adjusting the residence time, nickel adsorbs at approximately the same rate as that of the PGMs, influencing the loading capacity and adsorption kinetics of the PGMs. The feasibility of eluting platinum and palladium cyanide complexes from activated carbon using an analogue of the AARL process was investigated. Platinum and palladium elute from activated carbon almost to completion in 4 to 5 bed volumes at 80°C, while the elution of gold at this temperature is slow, with a significant amount of gold still to be eluted after 16 bed volumes. Cyanide pre-treatment was found to have a significant influence on PGM elution. Higher cyanide concentration in the pre-treatment step results in more efficient elution up to a point, and experiments suggest the possibility of an optimum cyanide concentration, beyond which elution efficiency starts decreasing.

Jan 1, 2012

By Q. Zhang, X. C. Wang, X. Q. Ao

The flotation separation of apatite and calcium-bearing gangue minerals (dolomite and calcite) has always been a problem in phosphate ore mineral processing research. The crystal structure and surface properties of minerals have an important influence on their floatability. In this paper, the theoretical and comparative analysis of the crystal structure and surface electronic properties of apatite, dolomite and calcite were carried out using the first principle calculation based on density functional theory. As a supplement and validation, the surface wettability of three minerals under different flotation conditions were compared and analysed by contact angle test. The results theoretically revealed that the three calcium-bearing mineral surfaces have similar surface electronic properties and thus exhibit similar floatability. In the flotation process, the anion difference between apatite and carbonate gangue should be fully utilised, and the minerals can be separated only after surface modification by flotation reagent. The contact angle test shows that phosphate and carbonate can be separated by using anion flotation collector after surface modification with acid. It is expected that this research is of interest for understanding the surface structure and electronic properties of apatite and carbonate gangue minerals and providing the theoretical basis for surface interaction. Keywords: Apatite, dolomite, calcite, surface structure, electronic property, density functional theory

Jan 1, 2020

By P. Michalcik, V. Petros, M. N. Bagde, K. Holub

The objective of this paper is to present some results of laboratory experiments during the investigation of stress-strain characteristics of Carboniferous sandstones at dynamic loading. During these experiments increasing frequency and the constant amplitude of dynamic loading and/or constant frequency at different amplitude of dynamic loading were applied. Der Gegenstand dieses Artikels ist, irgendeine von Ergebnissen von Laborexperimenten bei Messung der Spannungs- und Deformationscharakteristik der Karbonsandsteine bei ihrer dynamischen Belastung vorzustellen. Im Laufe diesen Experimenten wurden entweder anwachsende Frequenzen bei konstanter Amplitude der dynamischen Belastung, oder gleiche Frequenzen bei variabler Amplitude der dynamischen Belastung verwendet. L'objectif de ce papier est présenter quelques résultats d'expériences de laboratoire pendant l'enquête de caractéristiques de la tension – deformation de grès Carbonifère à sollicitation dynamique. Pendant ces expériences fréquence croissante et l'amplitude constante de sollicitation dynamique et/ou fréquence de la constante à amplitude différente de sollicitation dynamique ont été appliquées.

Jan 1, 2003

By J. Petersen, H. Naderi, M. H. Nikzad, M. Karimi

In this research, the thermodynamic study of sodium persulfate (Na2S2O8) solution in the presence and absence of H2SO4 and Fe3(SO4)3 was done. Eh-pH and equilibrium distribution diagrams were constructed using Outotec HSC Chemistry Software and the main stable ionic species were determined. Also, the mean activity coefficient and Pitzer model coefficients were evaluated. Effects of system composition, sodium persulfate concentration and temperature were investigated. According to the results, HS2O7 -, HS2O8 -, S5O3 2-, S4O3 2-, S3O3 2-, HS- and NaSO4 - are the main stable species in these three systems. Increasing of sodium persulfate concentration resulted in disappearing of SO4 2- and the appearance of NaSO4 -. The main effect of increasing the temperature from 25 to 75oC, is changing the stability regions of HS2O7 -, NaSO4 -, SO4 2- and S2-. From equilibrium studies, it was concluded that at 25 and 50oC, increasing the persulfate concentration results in a 55-60% decrease for HS2O7 - and an 20- 30% increase for HS2O8 -. At 75oC, HS2O8 - becomes the main species and its percentage decreases with increasing the persulfate concentration. Keywords: Thermodynamic, sodium persulfate, activity coefficient

Jan 1, 2020

By A. G. Royle

The reasons for constructing a model of an orebody for which both the parent population and the sampling distribution are known are discussed and details of the model are given. A brief summary of Matheron's theory of regionalized variables is included, with particular reference to his kriging estimators and their variances. Using the model, a comparison is then made between these kriging estimators and other commonly-used estimators. These are compared to find the one with the minimum variance, and an analysis is included to investigate whether any of the estimators is biased. Also included is a comparison between theoretical and experimental variances for some of the estimators.

Jan 1, 2014

By N. Mangadoddy, M. Padhi

The simulation of multi-component classification with modified viscosity model is the key focus in the current study. The classification of the ores using hydrocyclone is a renowned process and has a convoluted flow separation phenomenon. The highly turbulent flow inside hydrocyclone depends on the operating and design parameters apart from the feed mixture. Slurry viscosity also plays a dominant role in the classification of solid particles under the centrifugal settling action. A heterogeneous mixture with different components would result in different settling and rheological behaviour of particles’ suspension in the water medium. The newly proposed multi-component viscosity model (Mandakini et al. 2020) is implemented as a user-defined function to define the material property during the CFD study of the mixture rheology inside hydrocyclone classifier. The multiphase and turbulence model is solved using the modified Algebraic Slip Model and Large Eddy Simulation model. A comparison of the predicted component performance curves is evaluated with and without the corrected viscosity model. The density and size effect on the particle phase distribution inside the classifier are compared, where the misplacements of the finer particles are carefully assessed. Validation of the component classification in hydrocyclone with the laboratory experiments found a close agreement with the rheology based CFD data. Keywords: Dual-component, multi-component viscosity model, double-gap rheometer, computational fluid dynamics, high solids concentration

Jan 1, 2020

By C. T. O’Connor

Since the first IMPC took place in London in 1952 there have been many developments in our understanding of flotation, both in terms of chemical and physical factors influencing the process. Many of these developments have been captured in the proceedings of thirty congresses that have taken place since that first event, as well as in numerous journal papers and special volumes dedicated to flotation. This paper attempts to highlight the individual contributions which many eminent researchers and engineers have made over the past 70 years towards extending our understanding of, especially, the effects of chemical factors on flotation. Although the focus is mainly on more fundamental aspects, it seems that the ‘pull’ of practice has often preceded the ‘push’ from laboratory-based research. As the fundamental understanding of the role of chemical factors on flotation continues to be developed, the major challenge remains to transfer this knowledge effectively into the domain of operations of this profoundly complex process.

Jan 1, 2020

By A. F. Silva, R. Dockendorff, J. M. Girao Sotomayor, V. F. Navarro Torres, C. Castro

This paper shows the importance of performing probabilistic analyses in open pits, especially for mine planning, which can lead to more efficient ore extraction and meeting the acceptability criteria for safety in mine slopes. Three-dimensional stability analyses were performed to evaluate the future geometry of a large open pit for iron ore extraction in Brazil. The strength parameters of the lithologies were calibrated using ruptures in the pit walls. After determining the factors of safety (FoSs) from the calibrated parameters, probabilistic analyses were performed using the total range of values of each parameter under different field conditions to verify the reliability of the initial analysis. In this sense, it was possible to plot the probability of failure (PoF) and the FoS on the graph of slope height versus slope interramp angle (IRA) for the future pit in each lithology. IRA recommendations are made for two scenarios: (1) the best scenario: dry without ubiquitous joints and (2) the worst scenario: the water table at 10 m depth with ubiquitous joints in the most unfavourable direction. The results show that probabilistic evaluation is an important tool for establishing alert mechanisms in slopes that can be termed stable.

Jul 2, 2022

By I. Mitov, A. Stoilova, D. Krastev, B. Yordanov

We present three technological scenarios for the recovery of valuable components from gangue, stored in the tailings dam at Kremikovtzi metallurgical plant in Bulgaria, into marketable iron-containing pellets. In the first approach the iron concentrate was recovered through a two-stage flotation process, desliming, and magnetic separation. In the second proposed process, the iron concentrate was subjected to four sequential stages of magnetic separation coupled with selective magnetic flocculation. The third route entails the not very common practice of magnetizing roasting, followed by selective magnetic flocculation, desliming, and magnetic separation. The iron concentrate was pelletized in a laboratoryscale pelletizer. Each technology has been assessed with regard to the mass yield of iron concentrate, the iron recovery. and the iron, lead, and zinc content in order to identify the most effective route.

May 1, 2021

By A. V. Wilke

The metallurgical balance is a tool usually applied in the mining industry. The final result is used for different objectives. All the existing software for the calculation of the metallurgical balance fits the numbers in such way that a logical correspondence between the input and output materials exist. Nevertheless, the accuracy of the metallurgical balance strongly depends on the quality of the input data. Division El Teniente of Codelco Chile has been optimizing the metallurgical balance system the last 14 years. As well, it has participated in the development of corporate norms to optimize the operations of sampling and weighting systems. As a consequence, the precision and the accuracy of the metallurgical balance have been improved in a significant way. Also the understanding of process variability was enhanced. The improvements have allowed Codelco to discover and minimize hidden losses and to better support top management decisions. The present paper describes the main aspect of the continuous improvement process.

Jan 1, 2009

1. Book reviews Physiochemical properties of molten slags and glasses, by E.T. Turkdogan. London, Metals Society, 1983.516 pp. £35. Reviewer: A.F .S. Scboukens Microstructural characterisation of metals and alloys, by P.E.J. Flewitt and R.K. Wild. London, Institute of Metals, 1984. £14. Reviewer: M.P. Sbaw Metallurgical applications of magnetohydrodynamics, edited by H.K. Moffatt and M.R.E. Proctor. London, Metals Society, 1984.346 pp. U.K. £35, U.S. $70. Reviewer: N.A. Barcza Extractive metallurgy symposium. Proceedings of a meeting on 12-14 November, 1984, organised by the Melbourne Branch. Parkville (Victoria), Australasian Institute of Mining and Metallurgy, 1985. Reviewer: B.K. Loveday Conference on gold mining, metallurgy and geology. Proceedings of a meeting on 9-11 October, 1984, organisedby the Perth and Kalgoorlie Branch. Parkville (Victoria), Australasian Institute of Mining and Metallurgy, 1985. Reviewer: B.K. Loveday Corporate policies for the 1980's in the steel industry, by Patrick Genevaz in collaboration with B.A. Bloom. La Chambre des Cartes, 26 rue de Piepus, 75012 Paris (France). U.S.$7oo, additional copies $140. Reviewer: D.C. Maree Mineral processing technology, by B.A. Wills. Oxford, Pergamon Press, 1984 (3rd edition). 629 pp. Hard cover £31.50, soft cover £9.75. Reviewer: B.K. Loveday Ma1lllgement information-ma1lllging for improYement, volume 2: symposium proceedings and additional papers. edited by M. Hammond. Doncaster (England), The Institution of Mining Engineers, 1984. 86 pp. £60 for vols. 1 and 2 (124 pp.). Reviewer: M.J .R. Meyer 2. Recent publications Tins and its and its uses no. 144, 1985. This issue by the International Tin Research Institute (Fraser Road, Greenford, Middlesex, UB6 7AQ, Canadian minerals yearbook 1983-84. Department of Energy, Mines and Resources Canada, Mineral Report 33. Ottawa, Canadian Government Publishing Centre, 1985. $35.40. 82 Year 1984, edited by 1.0. Jones and RM. Louthean. Kalgoorlie (Australia), Western Australian School of Mines, 1985. 100 pp. Johnson Matthey Chemicals 1984-85, issued by Matthey Catalogue Sales (Orchard Road, Royston, Hertfordshire SG8 SHE, England). 416 pp. South Africa's mineral industry 1984. Johannesburg, Minerals Bureau, 1985. 190 pp. Coal 1985. Operating and developing coal mines in the Republic of South Africa. Johannesburg, Minerals Bureau, Directory 2/8S. 1985. 72 pp. Gold 1985. Operating gold mines and gold recovery plants in the Republic of South Africa. Johannesburg, Minerals Bureau, Directory 3/8S. 98 pp. 3. New journal Pergamon Press, New York, have announced the publication of a new quarterly known as the International Journal of Plasticity. 4. Mintek reports Report M93D Hydrochloric acid leaching and low-temperature roasting of tin-tungsten concentrates from Van Roois Vley. (First issued April 1983.) Report M99D The upgrading of coarse kyanite crystals. (First issued Report M105D The development and installation of a microcomputer based data logger, and the analysis and evaluation of data. (First issued July 1983.) Report M109D The remelting ofsi/iconfines. (First issued July 1983.) Report M180 An assessment of available corrosion inhibitors for the reticulation systems of South African gold mines. Report MW1 Quantitative assessments of abrasive and impactive wear from ball-size distributions in rotary mills.

Jan 1, 1985

By S. Dessureault

Computer Integrated Mining (CIMG) is a process of using computer networks to transform islands of enabling technologies into a highly interconnected mining system. CIMG involves the integration of advanced technologies at various levels in the mine business to achieve higher flexibility, better quality of processes and control, and improved profitability. Justifying the benefits of CIMG are difficult as many of the advantages are derived from improved flexibility, quality, and control. Justification is based on the evaluation of the benefits to be gained, compared to the required capital investment. Management tools used in mining are currently inadequate in assessing the value of advanced technology whose benefits are primarily qualitative. A key aspect of successful implementation is management acceptance, which has to be won through the capability to justify the technology's financial costs and the true value of all of its benefits. The manufacturing industry faced similar justification difficulties when adopting advanced technology in factories. A significant amount of funding and research was invested into developing management strategies and approaches to justification. Many of the problems that faced the transformation of the manufacturing industry in the late eighties and early nineties are now facing mining. The solutions derived for manufacturing may help mining in its transition to an increased reliance on integration technology. Reviewing the industrial history of computer integrated manufacturing identifies several tools and strategic frameworks that can be adapted for mining. Keywords: Computer integrated mining, justification techniques, CIM, information technology.

Jan 1, 2003

By L. Roux

The initial evaluation of a coal deposit often raises uncertainty with regard to the accuracy of the reported Resources and Reserves. Reconciliation of results from mining and beneficiation with the original raw field data highlights deficiencies in original estimations. Credible Resource and Reserve estimation forms the basis on which an entire mining enterprise is motivated, initiated, funded, and established as a commercially viable proposition. This is required for sustainable extraction purposes and to support vital downstream industries such as power generation. Accurate determination of the density of the matrix of the material being evaluated is the key to credible values being obtained for Resources and Reserves. Losses between 15% and 20% of the Resource/Reserve can be realized if incorrect densities are applied to the tonnage derivation. Coal plies and particles have different relative densities, determined by the maceral composition, rank, and mineral and moisture content. These factors in turn contribute to the moisture, volatile matter, ash and carbon contents of a coal, which affect the overall density of the raw coal. More specifically, the relationship of ash to density and the effective matrix porosity were found to be critical in solving the greater majority of the problems in predictive calculations. A major deficiency identified is the inability to determine effective porosity, allowing absorption of adventitious moisture and altering the mass of the core sample. Although the volume of the raw material is altered through crushing, the change in mass after controlled air-drying, used with the original geometrical volume of the raw material, provides a credible air-dry density and allows the determination of the volumetric change related to effective porosity. This parameter can be validated through the evaluation of proximate ash using the ash-adjusted algorithm and a correction for the inherent moisture applied to also give a credible relative density value for an air-dried sample. A combination of theoretical, empirical, and reconciliatory evaluations of the available data, taken from the exploration phase through the mining process to final production, has shown that an integrated approach using the ash-adjusted density (AAD) methodology, in conjunction with other evaluative techniques, provides credible results with a considerably higher degree of accuracy than is currently possible.

May 1, 2021

The current global economic climate has adversely affected the resources industry in general. For the gold mining industry, even though the gold price has been stable as compared to other resources, there is still a need to cut costs even further in order to be profitable and sustainable. Of all the costs that are associated with mining, comminution of ore accounts for the majority. Comminution costs constitute mainly electricity, grinding balls and liners. Of these three components, grinding balls form the major portion of the consumable costs, and can be as high as 40%?45% of the total. As a result, proper grinding ball selection is a key consideration towards reducing mining costs. This paper discusses quality control procedures that can be conducted in order to select the best grinding balls for a particular application. Keywords: grinding balls, forged, semi steel, hardness, chemical, metallography, wear testing, impact test

Jan 1, 2009

Broken Hill Mines-1968, edited by M. Radmanovich and J. T. Woodcock, published by The Australian Institute of Mining and Metallurgy, Melbourne, 613 pages. Price $A15. This volume, containing some 65 technical papers, was produced for the 1968 annual conference of the Australasian Institute held at Broken Hill to mark the 75th Anniversary of that Institute, founded at Broken Hill in 1893. That conference also coincided with the 85th Anniversary of the discovery of the Broken Hill mining field. This closely reflects the position in this country, where the Witwatersrand gold fields were discovered in 1886, and our South African Institute of Mining and Metallurgy will in March, 1969 be celebrating the 75th Anniversary of the founding of the forerunners of our Institute. There is a comprehensive report of the geology of the Broken Hill area and the mineralogy of the ore body, and there are reports on the mining methods and the metallurgical procedures which have been developed over 85 years of operation of one of the great mining fields of the world. The value of most of the papers is enhanced by a large number of illustrations and photographs. An early section covers the academic and practical aspects of rock mechanics, prospecting, and exploration techniques are described in some detail. A third of the volume is devoted to mining, with papers on 26 aspects. The breadth of the coverage gives an indication of much specialized development, research, and consequent maturity in all departments. The detailed treatment of metallurgical aspects such as sizings of individual mineral particles throughout the milling stages and the development of an on-stream analysis system for lead will commend this volume to the specialist. The committee responsible for the production of this volume, which brings together much information previously only to be found after searching through numerous publications, are to be congratulated on a well produced comprehensive review of many aspects of the mining and metallurgical fields. H.B.