Search Documents

By H. C. Miller

[California's sensational rise to supremacy as an oil-producing State in 1923 was accompanied by a loss of 62 lives. These 62 deaths were from oil-producing accidents alone and do not include fatalities at the refineries, on tankers, or on any work not directly connected with the drilling for and the production of oil. The number of facilities for 1923 was 82 per cent greater than in 1922, the next most fatal year, with a record of 34 lives lost. The data submitted in Table 1 show that for the calendar years 1917 to 1923 inclusive, an average of 4.74 million barrels of oil were produced per Vitality in the California oil fields. On this basis, the record for 1923, hough a trifle below the average, shove up slightly better than that for 1922.]

Jan 1, 1924

This report was prepared by Jacob Tolsma and Arnold N. Johnson of the Uniroya 1 Research Center, Wayne, New Jersey. The valuable assistance and suggestions of the project officers, Mr. Ronald D. Hill, Dr. David R. Maneval and Mr. John J. Buscavage is gratefully acknowledged. The authors are grateful to the following Uniroyal personnel: Mr. Daniel Shichman, manager of Engineering Research, and Dr. Emmanuel G. Kontos, manager of the Polymer Physics Research for their direction, encouragement and suggestions regarding the experimental work, and Mr. Mark Olson for the design of the hollow auger soil sampler. We also wish to gratefully acknowledge the efforts and contributions of ideas proposed by our consultants, Dr. Frank T. Caruccio, assistant professor of geology at State University College, New Paltz, New York, and Dr. Pa Ho Hsu, associate professor of soil chemistry, Rutgers University , New Brunswick, New Jersey.

Jan 1, 1972

By J. Whyatt

A variety of dynamic failure cases with regional impact were described at a bump symposium held in 1958. These types of events, while rare, are of particular interest because their ability to impact a large area has disaster potential. These cases can be grouped into two broad classes of events by mechanism. These are (1) slip along steeply dipping faults and (2) fracturing of strong strata above, or below, the coal seam. Both failure modes produce dynamic or ?shock? loads on the perimeter (roof, rib, floor) of mine openings. Special consideration should be given to these failure modes in planning of deep coal mines since their occurrence is not within the professional experience of many contemporary workers, and their potential is not evaluated by many of the analysis tools commonly used to evaluate hazards in coal mine plans.

Jan 1, 2009

By Jack E. Fraley

Magnesium oxysulfate cement has been specially formulated as a sealant in underground coal mines for reducing sloughing of shale roofs and coal ribs, for reducing air losses through block stoppings, for constructing sprayed stop-pings over approved jute cloth or metal lath, and for reducing combustibility of polyurethane foam. A standard spray machine (Mining Enforcement and Safety Administration (MESA) approved) was used for the underground testing. Our research shows that a 1/2-inch coating reduces shale and coal sloughing, reduces air losses through block stoppings, and prevents fire propagation through a metal tunnel lined with polyurethane foam. During the underground tests, excess mixing water was used to improve pumping the slurry to the spray nozzle. This was later found to increase shrinkage cracks in the cured coatings. Controlling excess water is important to an acceptable coating.

Jan 1, 1976

By A. T. Coumbe

The Bureau of Mines has compiled pipeline mileage every 5 years since 1926, with the exception of the war period 1941 to 1949. The present survey has been made to reflect the progress under mobilization of the petroleum pipeline industry where efforts have been made by the government to stimulate construction of those facilities that would best equip the nation for a possible major emergency. This report summarizes the total mileage change 1n petroleum pipelines for 1950 through 1952. In order to increase the value of the information gathered the reporting companies were requested for the first time to report not only the net change in mileage as formerly, but also all new and used pipe laid and the total taken up. This new information permits effective appraisal of the construction effort of the industry and relates it to steel requirements.

Jan 1, 1953

Reduce exposure of longwall face workers to respirable dust generated during the advancement of roof supports. Approach Identify and implement current water-application and improved support-movement practices used to lower support-generated dust. Defining the Problem Bureau studies have shown that on some longwall faces support dust can contribute over 30 percent of the respirable dust exposure of face workers. Conditions contributing to high levels of respirable dust generation during support movement are: depth of cover greater than 1,000 ft; immediate roof consisting of coal top or friable shales; and face-air velocities in excess of 500 fpm. Moreover, at most longwalls, supports are advanced on the intake-air side of the shearer as it travels with the airflow. This places the shearer operators, and in many cases the support movers, downwind of support advance, thus increasing their respirable dust exposures.

Jan 1, 1984

Louisiana's coal reserves, located in the north-western part of the state, consist entirely of lignite, with estimated recoverable reserves of about a billion tons. Although lignite deposits were discovered in the early 1800s, the first documented use of lignite occurred at the federal arsenal near Shreveport during the Civil War. By the late 1800s, lignite use was common by blacksmiths, railroads, and steamboats. Lignite production ceased, however, from the early 1900s until 1985. A new lignite mine permitted September 1, 1985, produced 0.2 million tons in its first year. The operation uses a seven-mile-long conveyor to transport lignite to the associated mine-mouth power plant. The surface coal mining reclamation and enforcement program in Louisiana was approved October 10,1980. Louisiana's Abandoned Mine Reclamation Plan was approved December 10, 1986

Jan 1, 1992

By L. J. Prosser, A. T. Iannacchione

From 1991 through 1995, 44 miners out of a total workforce of less than 2,000 were fatally injured in the stone industry. Of these, 12 occurred at underground mining operations with nine deaths resulting from roof or rib falls. A safer environment can be achieved by evaluating the nature of the hazardous ground and by developing more efficient and effective ground-control strategies Roof and rib conditions were observed and assessed in 33 underground stone mines in Illinois, Indiana, Kentucky, Maryland, Missouri, Pennsylvania and West Virginia (Fig. 1). Hazard assessment indicated that the ground failures that occurred under moderate to substantial overburden. i.e., >30 at (100 ft), were caused by stress concentrations and geologic strictures. Ground failures near the surface are caused by solution (water) processes. Selection of the mining horizon and mine-layout decisions tremendously influence ground stability.

By Jack Wasserman, Don Wasserman, Gretchen Hinton, Logan Mullinix, Shekar Khanal

Human testing has always been a needed way to provide information on the effects of vehicle vibration, however, the manner of testing has not reflected the real situations of driver’s hands on a steering wheel and a seat with back support and driving tasks. The typical system have used a standard sinusoidal excitation rather than the typical types of road – truck excitations The new truck driver training simulators provide the combination of road roughness, speed effects, cab environment and individual tasks. The system has a full six axis simulation potential. The simulators have the protection of the individual by a combination of two ways for the individual to stop the motion as well as an operator with visual capability who can stop the testing. The closed simulator, shown in Figure 1, has the potential for providing motion during the operation.

Jan 6, 2006

By H. K. Kutter

The pressure pulse generated by an underwater spark \vas investigated in relation to its potential use for rock fragmentation. The study established (1) the relation between the peak discharge current and the peak wave pressure; (2) the relationships among the peak wave pressure, the discharge voltage, and the spark gap width; (3) the type and pulse duration of the generated wave; (4) the percentage of energy transmitted in the spark as a function of spark gap width and discharge voltage; and (5) the percentage of energy converted into the pressure wave as a function of gap width and discharge voltage. Spark-generated fractures were studied in two-and three-dimensional rock and plastic specimens. The laboratory results indicated that the pressure pulse generated by an underwater spark is a potential practical tool for rock fragmentation. The paper contains an appendix describing the capacitive pressure gage specially developed for the laboratory tests.

Jan 1, 1969

By Ted C. Briggs

The Bureau of Mines is evaluating the thermodynamic properties of helium and helium-containing mixtures. Twenty-two compressibility runs were made with helium at 0° C and pressures to 800 atmospheres using a Burnett-type apparatus. Data from the 22 runs were treated simultaneously and as separate runs while different functional forms and weighting factors were used. A fourth-degree-polynomial equation in the pressure gives a statistically satisfactory representation of the compressibility factor when the data are treated simultaneously and a weighting factor of Pr-3/4 is used. The second virial coefficient of helium at 0° C from this investigation is 11.997±0.015 cm3 mole-1. The stated uncertainty is the random error standard deviation. Compressibility factors determined by this investigation are precise to better than 0.01 percent and are believed to be accurate to better than 0.02 percent.

Jan 1, 1969

By R. L. Schmidt

The Methane Control and the Respirable Dust Groups at the Twin Cities Mining Research Center (TCMRC) cooperated recently in obtaining production samples of approximately 1 ton each, from the loading conveyors of a ripper, a borer, and a loading machine in conventional development headings. These samples were sized, in four stages, from plus 4 in to minus 10 µm. The conventional product had the least fines of the three production methods. The borer product had more fines than did the ripper product, but it also had a greater amount of large pieces. All three products, as sampled, had essentially the same amount of minus 10-µm particles. Photomicrographs and surface?-area comparisons were made. Gas -adsorption, surface-area determinations on particles under 37 µm give essentially the same value. Surface-area calculations, assuming spherical particles and no porosity, give a smaller area to the conventional product.

Jan 1, 1972

By C. Melvin Lepper

To provide the U.S. mining and energy industries with information in the selection of seismic detectors for high-resolution applications, the Bureau of Mines evaluated 35 velocity detectors (geophones) and 9 accelerometers. It was found that velocity detectors with natural frequencies from 10 to 100 Hz were effective for seismic studies in the 5-to 600-Hz spectrum and that accelerometers were most effective in the 100-to 1,000-Hz range. Although the accelerometers described in this report performed about equally with the better velocity detectors tested, the accelerometers showed higher output voltage levels at higher frequencies, which is an advantage. It is important that a seismic detector and its intended purpose be matched properly to achieve the intended results in high-resolution applications. There are many factors that could affect proper matching, thus careful selection of the best detector for a particular application must be exercised.

Jan 1, 1981

By J. A. Lamonica

The Bureau of Mines studied two types of approved coal mine dust personal samplers to determine the effect of decreasing the amplitude of airflow velocity fluctuations on cyclone performance. Results indicate that more dust is collected when pulsation free flow is used. Velocity fluctuations were reduced by means of a pulsation damper; damper efficiency of about 85 percent was needed to reduce the fluctuations to an acceptable level. The data were obtained employing both pulsating and non-pulsating flow. A comparison was made of (1) the masses of respirable coal dust as determined by weighing and of (2) the particle size distributions as determined by an electronic counter. An empirical relationship is given between the ratio of masses collected using pulsating and nonpulsating flow (M') and the ratio of the maximum air velocity to the minimum air velocity (V') as measured in the cyclone entrance channel.

Jan 1, 1972

By B. Dimitriades

The Bureau of Mines measured the reactivities of 19 hydrocarbons known to be prominently present in automotive exhaust and ambient air in a smog chamber. Results agreed well with those obtained using two other smog chambers. Reactivity scales were developed for hydrocarbons and aldehydes using the results of this work and those of a previous study. Application of the reactivity scales to automotive exhaust samples gave fair agreement between predicted and observed rate-of-N02-formation values; however, predicted and observed ozone yields were neither in agreement nor did they correlate well. This lack of correlation for ozone yield was attributed to the inappropriateness of (1) the individual component reactivity data, (2) the reactivity classification scheme used, and (3) the linear summation method. In seeking to understand this problem and to develop more appropriate reactivity scales, the data were examined from a reaction mechanism standpoint, and further studies were suggested.

Jan 1, 1975

By J. E. Zeilinger

This Bureau of Mines report describes the preparation characteristics of the significant coalbeds of Beaver and Lawrence Counties, Pa. Washability analyses were made on seven coalbed samples, none of which were of metallurgical quality as received. Five of the samples could be sufficiently upgraded to produce acceptable products, and the remaining two samples could not be upgraded to metallurgical quality because their sulfur contents could not be lowered to meet the standard. For steam or power generation, one sample was of low sulfur content as received, one sample could be upgraded to low sulfur content, and three samples could be upgraded to medium sulfur content. The original sulfur content of the remaining two samples can be appreciably reduced by removal of the sink 1.58 speci fic gravity material; however, these coals would be classified as medium sulfur coals both before and after removal of the sink material.

Jan 1, 1969

By Donald O. Capstick

In 1481, U.S. Bureau of Mines personnel conducted a survey of mines, prospects, and mineral resources in the Table Mountain RARE II area. There are no mines or active prospects in the study area. One prospect in the study area, the Waterfall Prospect, is estimated to contain 480 tons (440 t) of indicated subeconomic tungsten resources averaging about 0.18 percent tungsten trioxide (W03). Other tungsten occurrences are at the Stevens Prospect, just northwest of the area. Stone and sand and gravel deposits in the area are not considered to be resources because equal or better quality material is available closer to major markets. INTRODUCTION The 4,400-acre Table Mountain study area is 13 mi (21 km) southwest of Bishop, California, on the eastern flank of the Sierra Nevada range. The John Muir wilderness adjoins the study area on the southwest (fig. 1).

Jan 1, 1982

By F. N. Kissell, R. J. Bielicki

The Bureau of Mines found sulfur hexafluoride (SF6), released from a lecture bottle, to be an ideal gaseous tracer for studying mine ventilation systems. Air samples were collected in glass syringes and analyzed by electron-capture gas chromatography. In these studies, the lower limit of detection was about 1 part per billion by volume (ppb) of SF6 per part of air. Experiments conducted in a Pennsylvania limestone mine showed this technique useful in evaluating the effectiveness of auxiliary fans, measuring low flow velocities, probing the air circulating near a working face region where ventilation appeared to be poor, and estimating volumetric flow rates in airways of large cross-sectional area and having low flow velocities. This technique was also used in a western vein-type metal mine to measure the amount of return air being recirculated into the intake air due to leakage through old stoped areas.

Jan 1, 1974

Reduce mine worker dust exposure by capturing airborne coal and quartz dust generated by a continuous mining machine. Approach Install a water-powered scrubber system operating at 1,000 psi on the side of a continuous miner boom. Dusty air under the boom is drawn through the scrubber, and cleaned air is discharged into the face return. How It Works Most coal mines use exhaust face ventilation to send fresh air over the miner operator, and contaminated air behind the line curtain to the section return. The difficulty with exhaust face ventilation is that the line curtain should be within 10 feet of the face for maximum effectiveness. If the line curtain is not extended properly, or water sprays for dust control are poorly installed, dust rolls back toward the operator. A scrubber mounted on the mining machine will effectively reduce this dust rollback and the dust in the return airstream.

Jan 1, 1989

Provide mine personnel with a convenient means of determining the optimum installation geometry of roof trusses in bedded roof. Background Mine operators frequently ask the following questions concerning roof truss installations: 1. Where should the bearing plates or brackets be placed or where should the inclined holes be started? 2. At what angle should the holes for the inclined chords or angle holts be drilled? 3. What tension should be put into the inclined chords so as to achieve the most effective results for the effort and expense? Truss hardware manufacturers have responded to these questions with answers based on what seems to work best. While designs based on past experience are frequently reliable, there was a need for a rational approach that could accommodate a variety of conditions. The Bureau has developed a procedure that enables mine operators to optimize roof truss installations in bedded roof.

Jan 1, 1989