Search Documents

By Wallace W. Roepke, Jon I. Voltz

"The Bureau of Mines determined coal-cutting forces and primary dust generation of four styles of radial gage bits as used on end rings of continuous mining machines. Direct comparisons for reference were made with two widely used conical plumb-bob types having 60° and 90° (nominal) included tip angles. The cutting forces for all of the gage bits were similar to those of the 60°-tip plumb-bob bit. All bits except the RAD-3 gage bit generated similar amounts of primary total dust at shallow cutting, but during deeper cutting, the amounts varied and the gage bits produced as much as 2-1/2 times the dust produced by the 60° bit. This seems atypical since past experience has always shown differences in dust generation at shallow cutting. The specific energy was more like that found previously with other bits, since the values were spread at shallow cutting but became nearly similar at deeper cuts. The 90° bit and the RAD-3 gage bit are not recommended for use except in extremely difficult cutting conditions where dust and forces are of secondary importance. The choice among the remaining four bits can be made on the basis of dust, energy, forces, or cost, as circumstances dictate. INTRODUCTIONThe Federal Coal Mine Health and Safety Act of 1969, with revisions in 1977, was enacted to ensure more healthful and safer working conditions for miners. The Bureau of Mines coal-cutting research facility at Twin Cities (MN) is examining fundamental aspects of the cutting system, including generation of primary dust causing pneumoconiosis in miners and ignition of methane by the frictional impact of cutting bits used on continuous mining machines (CMM's). The cutting system is defined as the cutter-mineral interface area with all its variables, e.g., forces, speed, cutter geometry, bit-mounting geometry, and wear. It has become obvious over the past several years that the cutting system directly affects the economics and design of the ""total system,"" which is defined as all areas of the operation, from the mine face to the preparation plant, which support the mineral recovery by cutting tools to obtain a salable product."

Jan 1, 1983

By J. Dean Warner

In 1984, as part of a project to evaluate Alaskan occurrences of certain critical and strategic minerals, the Bureau of Mines investigated a columbium-bearing regolith on upper Idaho Gulch, near Tofty, AK. The regolith is derived from weathering of a dolomitic marble and consists mostly of iron oxide minerals with accessory apatite, zircon, xenotime, rutile, monazite, and the columbium minerals aeschynite, columbite, and ilmenorutile. Two regolith lenses contain 340,000 lb of columbium resources at an average grade of 0.07 pct. Calculated composite concentrates from two regolith samples (approximately 200 lb each) contained 53 and 57 pct of the columbium at grades of 0.97 and 0.86 pct, respectively. In each case the grade could be improved to 1.1 pct Cb with a sacrifice of 9-pct recovery. The regolith's mineralogy, trace-element geochemistry, and similarity to descriptions of other columbium-enriched regoliths suggest that the underlying marble may be a carbonatite. The lack of associated alkalic igneous rocks and the stratiform nature of the regolith, however, may be interpreted as evidence for sedimentary origin of the marble. The marble and regolith are a lode source for some of the minerals in the Idaho Gulch placer deposit.

Jan 1, 1986

By H. B. Humphrey, F. E. Cash

From 1900 to 1929 , 1,005 or approximately 30 per cent of all fatalities in the coal mines of Alabama were caused by fires or explosions of gas and dust . In the 3 -year period from 1927 to 1929 only 15 men were killed by these causes , a reduction from 30 to 9 per cent of the total . Notwithstanding this marked improvement , which is due largely to the efforts made by the State inspection department , the operators , and the Bureau of Mines to stamp out this type of disaster , Alabama still has more than its share of such fatalities which can and should be prevented. A list of explosions from 1894 to 1929 compiled from information obtained through the records of the State Inspector's office , the reports of Engineers of the Bureau of Mines , and the operators , is given in Table

Oct 1, 1930

By Manuel Gomez

A general prediction model for the Hardgrove grindability index was constructed from 735 coal samples using the proximate analysis, heating value, and sulfur content. The coals used to develop the general model ranged in volatile matter from 12.8 to 49.2 percent, dry basis, and had grindability indexes ranging from 35 to 121. A restricted model applicable to bituminous coals having grindabilities in the 40 to 110 range was developed from the proximate analysis and the petrographic composition of the coal. The prediction of coal grindability within a single seam was also investigated. The results reported support the belief that mechanical properties of the coal are related to both chemical and petrographic factors of the coal. The mechanical properties of coal may be forecast in advance of mining because the variables used as input to the prediction models can be measured from drill core samples collected during exploration.

Jan 1, 1970

The initial results from the magnetic sludge factorial experiment are summarized in Table 2. For ease in interpretation, the four separate variables are identified with the high and low level of each variable being represented by + and - signs, respectively. Several important relationships are evident from an inspection of the data in Table 2. For example, magnetic sludges were obtained only during the high temperature tests. Secondly, with the exception of the last three tests, there is an apparent correlation between settled sludge volume (or sludge settling rate) and pH. Data on residual dissolved Fee+ indicate that precipitation of iron is not complete at pH 8 and room temperature (Tests l, 3, 5, and 7). Although this should not have any confounding effect on the interpretation of the results, it is an important observation and an aspect of the overall conceptual process that should be considered carefully during any future developmental work. The data in Table 2 were employed more fully in the calculation of main effects and variable interactions for each of the three responses. For this purpose, a codified design and calculation matrix, shown in Table 3, was used. The derivation of this matrix is described by Davies.(9) The positive or negative signs for variable interactions are obtained simply by algebraic multiplication of the signs for each single variable involved in the interaction. Main effects and interactions are calculated by multiplying the response values (Table 2) by the corresponding effect elements (Table 3), summing the results, and dividing by 8. The resulting value for single variables is also sometimes designated as an average effect, since (for tyro levels of the variable only) it is simply the difference between the average response of all trials carried out at the first level of the variable (factor) and that of all trials at the second level. If the effect of one variable changes at different levels of another variable, the two variables are said to interact. The relative importance of the variable or variables in question is reflected by the absolute magnitude of the calculated main effect or interaction. First-order (two variable) interactions are usually easy to interpret in terms of the physical behavior of the system. Second- and higher-order interactions are often less readily understood, and are often of minor significance in any case. The main effects and interactions derived from the present study in the manner described above are listed in Table 4. It should be noted that

Jan 1, 1971

By D. N. Nilsen

The Bureau of Mines is investigating a method to recover Ni, Cu, and Co from low-grade domestic laterites through reduction roasting, leaching, sol-vent extraction, and electrowinning unit operations. The objective of this research is to develop processing technology that can convert low-grade domestic deposits containing critical metals into national reserves. As a part of this research, a solvent extraction system was investigated for the extraction of nickel and copper, followed by the separation and production of suitable electrolytes. Nickel and copper were coextracted from ammoniacal ammonium sulfate leach liquors (pH~9.5) with LIX 64N extractant in a laboratory-size mixer-settler continuous circuit. Three extraction stages resulted in >99-pct extraction of nickel, substantial copper extraction, and essentially no cobalt extraction from leach liquors. A crowd stage reduced the ammonia loading on the solvent by maximizing nickel loading. Residual ammonia was removed from the loaded solvent with a pH-controlled scrub. Nickel and copper loaded on the solvent were separated by selective stripping. Typical nickel strip circuit operation using electrolyte containing 90 grams per liter (g/l) Ni and 11.9 g/l H2S04 yielded >99.9 pct Ni stripped from the solvent in five stages. The copper loading on the recycled solvent was controlled in a copper strip stage using electrolyte containing 25 g/l Cu and 160 g/l H2S04,

Jan 1, 1981

By P. T. Brooks

The selective recovery of nickel and cobalt from impure raw materials is being investigated by the Bureau of Mines as part of a program to develop improved procedures for preparation of pure metals. A combination solvent extraction-electrolytic process has been developed in the laboratory that enables preparation of high-quality nickel and cobalt from nickel oxide containing, in percent, 76 nickel, 0.8 cobalt, 0.5 magnesium, 0.2 iron, and lesser quantities of copper, zinc, and other metals. The oxide was smelted, using carbon as reductant, and cast into anodes. These anodes subsequently were dissolved in diaphragm-type electrolytic cells. Nickel and cobalt were deposited separately from appropriate electrolytes, concurrent with dissolution of the impure anodes. Anolyte containing nickel and cobalt in the form of chlorides and sulfates was treated for removal of impurities and separation of nickel and cobalt. First, iron and aluminum were removed as hydroxides by adding nickel hydroxide to raise the pH of the anolyte from 2.3 to 4.5. Next, the pH was adjusted to 2 by adding hydrochloric acid, and the solution was treated by solvent extraction to separate nickel and cobalt.

Jan 1, 1963

By Manuel Gomez

Dehydrogenation factors, proximate analysis, and ultimate analysis were examined as predictors of the low-temperature -carbonization properties of coals varying in rank from lignite through anthracite. All factors studied contributed to reduction in variance of the sample populations investigated. Response surface regression models based on variables from proximate and ultimate analyses of coal were constructed for eight low-temperature carbonization assay product and gas component Fields. These models were tested with independent samples that included drill cores, sized fractions, petrographic fractions, and run-of-mine coal. The models developed were used to predict low-temperature carbonization yields or coals from major fields of Wyoming. This information was cast in the form of contour plots describing the potential low-temperature carbonization product yields of Wyoming coals and the properties of the resultant char or coke. The variables used as input v the models may be measured and collected during exploration; thus, the carbonization properties of a seam can be determined in advance of mining. The information presented in this report is useful in that it broadens the deciionmaking base for management when either mine locations or coal conversicl plant sites, or both, are being considered.

Jan 1, 1971

By Stephen D. Cramer

The solubility of methane, carbon dioxide, and oxygen was measured in brines at temperatures from 0° to 300° as part of Federal Bureau of Mines research on the corrosion of metals in high-temperature geothermal and mineral processing environments. Solubilities were measured by the technique of extracting pure gas, dissolved at pressures where Henry's law was applicable, from known volumes of brine. The results were smoothed with respect to temperature. The solubility, expressed in terms of the Henry's law constant, reaches a maximum at temperatures ranging from 60° to 100° C for methane and oxygen, and from 160° to 170° C for carbon dioxide. The Henry's law constant increases, that is, gases are salted out of the brines, in the presence of dissolved salts. Salting-out coefficients are strongly dependent upon temperature. The temperature dependence of the Henry's law constant for geothermal brines is different from that for sodium chloride brines owing to the more complex chemistry of the geothermal brines. The solubility of oxygen and carbon dioxide in brines exposed to air saturated with water vapor and at a total pressure of 760 mm Hg is reported for temperatures from 0° C to the normal boiling point.

Jan 1, 1982

By Richard C. Repsher

Intermittent mining in the slope section at Dutch Creek No. 1 mine, Carbondale, Colo., of the Mid-Continent Coal and Coke Co. has resulted in erratic and minimal rock noise data, which, in turn, has necessitated a change in the method used to plot daily mine noise in order to be useful to the researchers at the mine. Daily and weekly cumulative plots of rock noise under these conditions have not shown significant stress changes as clearly as bimonthly or longer noise rate plots. Hence, longer term cumulative rock noise plots, as described in this Bureau of Mines report, have been added to the data analysis at Dutch Creek No. 1 mine, and have been shown to delineate unique areas of rock noise activity more clearly than shorter term plots. The longer term plots should aid in the detection and delineation of potential failure areas, when used in conjunction with other proven forms of data analysis.

Jan 1, 1979

By C. K. Lee

This Bureau of Mines report presents results from experimental studies on wood fires in a laboratory-scale tunnel network. Experimental measurements include ignition delay time, flame spread rate, ventilation air and gas flow rates, wood temperature, gas temperature, pressure and composition, thermal flux, and smoke particulates. These measurements form a data base for fire-scaling studies and provide information on various fire processes, such as flow interaction between ventilation air and fire, fire throttling and reverse flow, and duct fire energetics. Results show how hazards of duct fires relate to the development of (1) asphyxiating and toxic fumes, (2) explosive gas mixtures, (3) throttling of ventilation air, and (4) high-temperature combustion products. Such fire hazards should be carefully considered when testing flammabilities of materials used in a confined underground mine environment.

Jan 1, 1980

By H. R. Grau

NIOSH’s Pittsburgh Research Laboratory is currently involved in research to identify silica dust generation in underground metal/nonmetal mines. The ultimate goal of this research is to develop control technologies to reduce worker exposure to respirable silica dust. Commodities and job classifications with the highest silica dust exposure have been identified through analysis of the Mine Safety and Health Administration (MSHA) compliance dust sampling database. Dust surveys were conducted in an underground limestone and gold mine to investigate silica dust sources, generation levels, and controls being used. A summary of the mining operations, sampling procedures, resulting data, and suggested methods to improve the dust control will be provided.

By Mark R. Stephenson

Everyone knows that mining is a noisy job, but did you know that you are nine times more likely to lose your hearing than someone who works in a quieter job? If unprotected from noise on the job, by age 50, you will probably need hearing aids. Obviously, the best solution is to engineer out the noise, but that isn?t always im­mediately possible. Until mines are quieter, one way you can help save your vital sense of hearing is to use hearing protectors whenever the noise around you is hazardous. Even if you already have some hearing loss, you can use hearing protectors to prevent your hearing from getting worse. When loud noise is present, proper use of hearing protectors will help miners pre-vent most or all noise-induced hearing loss.

Jan 1, 1998

By W. H. Young, R. L. Anderson

"Physical conditions, such as thickness and character of the coal seam, dip or pitch of the seam, depth of cover, character of roof and overlying strata, mine water, etc., affect the productivity in bituminous-coal mining. Thickness of the coal seam being mined is probably the most important single item that determines whether the output per man per day shall be low or high; however, in strip mining the depth of cover or overburden to be moved is of equal importance.Bituminous coal is mined today from seams of exceedingly variable thickness - less than 2 feet to more than 50 feet; however, a large majority of the mines are producing .coal from seams 3 to 6 feet thick. The average thickness of the coal seams mined in the United States has not changed materially in the past 25 years. The average seam thickness for all bituminous-coal mines was 63 inches in 1920 4/ and 65 inches in 19)45. As thick seams have been exhausted in the older fields, other thick seams, have been opened in the newer fields.Productivity increased from 4 net tons per man per day in 1920 to 5.78 in 1945. This 45 percent increase in productivity resulted from increased mechanization. The percentage of underground production represented by coal cut by machines increased from 61 in 1920 to 91 in 1945 Mechanical loading increased from less than 1 percent of underground production in 1920 to 56 percent in 1945, and strip mining increased from less than 2 percent to 19 percent of the total production during the same period."

Dec 1, 1947

By Donald E. Graham

A mineral survey of a 12,350-acre portion of the 13,150-acre Juniper Creek Wilderness Study Area (WSA) in southwestern Idaho was conducted by the U.S. Bureau of Mines in 1984. The area is entirely underlain by thick flows of Banbury Basalt. Rhyolitic tuff of Little Jacks Creek is exposed in the walls of the Owyhee River canyon beneath the basalt. Minor units of lacustrine sediment occur between the volcanic layers. No mines or claims occur in the area, and no mineralized zones were found. The study area is covered by oil and gas leases or lease applications; there has been no known exploration.

Jan 1, 1985

Reduce the exposure of diesel vehicle operators to diesel exhaust generated during mucking in deadend drifts. Approach Direct the diesel engine exhaust upward and rearward thereby using the thermal buoyancy of the hot exhaust to form a layer at the roof, above the breathing zone of the vehicle operator. Modifying the Exhaust Outlets Diesel front-end loaders used in nocoal mines to remove blasted ore usually operate in entries open only at one end to cross cut ventilation. These deadend drifts are not usually ventilated with the use of auxiliary fans and vent tubing because of frequent blasting. The existing ventilation, therefore, is usually poor, and a diesel engine operating in such a drift emits exhaust which is not immediately swept away from the operator. On most load machines, the diesel engine's exhaust outlet is located near the floor and directed downward or to the side, so that when the hot exhaust is emitted, it mixes with the mine air as it rises into the vehicle operator's breathing zone. In this way, a uniform concentration of diesel exhaust forms around the operator.

Jan 1, 1983

By G. R. Hopkins, A. B. Coons

A survey of the petroleum pipe lines by the Bureau of Mines as of May 1, 1923, shows that on that date there was a total of slightly more than 90,000 miles of pipe lines in the United States, having a capacity of approximately 15,750,000 barrels, which is equivalent to one-fourth of the nation's average production for one month. These lines varied in diameter from 2 to 16 inches, the weighted average being 6 inches. The total pipe-line milenge was about equally divided between trunk lines and gathering lines, though the capacity of the former was about four times that of the latter. This was due, of course, to the difference in average diameter, that for the former being 7.4 inches as compared with 3.7 inches for the latter. The common size for trunk lines was 8 inches, and for gathering lines 2 inches. Oklahora, with 19,180 miles of pipe lines, is the leading State in total mileage, with Texas second and Pennsylvania third. From point of trunk lines alone Texas is considerably ahead of any of the other States, a position which it owes to its size and to the growth in the rovement to its Gulf ports. Cali- fornia, though the leading State from point of production, ranks only seventh in pipe-line mileage. This is due to the fortunate location of the Los Angeles Basin fields, some of which are within sight of the refineries to which their oil is delivered or of the port of San Pedro through which their oil is shipped. The last survey of this nature, made in the spring of 1924 by the U. S. Geological Survey, recorded a total mileage of nearly 83,000 with a capacity of approximately 14,450,000 barrels. This indicates an increase of 9 per cent in both mileage and capacity during the two years.

Jan 1, 1927

By John Ward Smith

Methods for estimating the amounts of nahcolite, dawsonite, and the sum of these two sodium carbonate minerals from oil-yield assay data are developed and evaluated for Green River Formation oil shales from the saline section of Colorado's Piceance Creek Basin. Derived statistically, these estimation methods depend on the fact that these minerals yield water and gas measured during oil-yield assay. The estimation procedures yield values for nahcolite and nahcolite-plus-dawsonite of sufficient accuracy for stratigraphic plotting and correlation, whereas estimates for dawsonite are more generalized. However, resource estimates and reserve computations for both nahcolite and dawsonite accurate within 10 percent of the real value are readily available by summing the mineral amounts calculated by the procedures presented. These estimation procedures are applicable to oil-yield assay data on core samples from more than 30 coreholes which have penetrated the saline section of the Green River Formation in Colorado.

Jan 1, 1972

By David A. Monaghan, Kenneth R. Maser, Adi R. Gurdar, D. Randolph Berry

5. Development of Initial Probing System 5. 1 Introduction The preliminary evaluation of a variety of potential methods for initial probing showed that the optical system using closed circuit television (CCTV) and the sonar, or acoustic ranging, system were the most promising. The former is capable of pro¬viding a visual display of the mine passages in a clear, non-smoky environment, and the latter is capable of providing a map of the spatial location of the coal surfaces making up the entries, as well as objects, such as cribs, mining machines, etc., in the passages in both smoky and non-smoky environments. The sonar system used in conjunction with the CCTV in a clear environment can greatly assist in resolving the spatial distribution of objects seen on the TV screen. Further, in a smoky environment the interpretation of the sonar information could be facilitated if some visual information were also available. CCTV systems exist but require some modifications to suit this particular application. The Industrial Hazards and Communications Division of the Bureau has an ongoing program for the development of such a CCTV system. Rather than duplicate this effort in developing a CCTV system, it was decided to evaluate the possibility of utilizing their system for initial probing, while continuing with the develop¬ment of a system which would work in any environment, including the presence of dense smoke. The concept of using sonar for the initial probing of mine passages represents the application of new technology requiring development. The results of such a development effort undertaken during the course of this program are described in the following sections.

Jan 1, 1973

By Wesley A. Grosh

The Toncrae-Howard copper deposits in Floyd County, Va., were first mined about 1800. The property has been operated or under development at various times since then for iron, copper or sulfur, although the total production has been small. The deposit consists of a vein or zone of sulfide mineralization in schist composed mainly of pyrrhotite with minor copper values in the primary zone and some rich areas of copper mineralization in the altered zone. The Bureau of Mines, in an attempt to develop minable copper ore during the war, opened part of the mine for examination and sampling, deepened the shaft and other underground work, and drilled 29 holes totaling 2,187 feet.

Jan 1, 1948