Search Documents

By Thomas Varley

Data on the consumption of reagents used in flotation during the years 1923 and 1924, in metallurgical plants in the Unites States, are presented in this paper. Two previous reports Lave been issued by the Bureau of Mines on consumption of oils and other reagents used to flotation - namely, "Statement of Flotation Oils," by O. C. Ralston, issued in 1913, and Serial No. 2203, "Consumption of Reagents Used in Flotation," by Thomas Varley, for the year 1919, issued in January, 1921.

Jan 1, 1925

By Dennis R. Dolinar, Lewis A. Martin

Cable bolt technology used by the U.S. coal industry was developed to a large extent in the 1990s. Today, these cable systems include both cable bolts and cable trusses to provide supplemental and secondary support in gate roads. This cable technology is significantly different than the cable systems in use in either U.S. hard-rock mines or Australian coal mines. Development of this technology was initiated and spurred by research efforts of the U.S. Bureau of Mines, and has continued under the health and safety programs of the National Institute for Occupational Safety and Health (NIOSH). It was also followed up by work of roof support manufacturers to create an essentially new support system. In this paper, the important support characteristics of both cable bolts and cable trusses are discussed. The design of cable systems and the basis for that design for tailgate and headgate situations are reviewed and explained. Case histories are presented on the application of these support systems based on experience gained at a number of in situ test sites.

Jan 10, 2000

By J. D. Marchant

Solid-state electrotransport of impurities in cerium, lanthanum, and praseodymium, using a pulsed current, was investigated. The results were compared with those of using a steady current. Impurities that showed appreciable movement with the pulsed current, but not with the steady current, were as follows: Molybdenum and oxygen in cerium, aluminum, iron, and molybdenum in lanthanum. The use of a pulsed current enhances the practical application of solid-state electrotransport to remove a wider variety of impurities from the host metals.

Jan 1, 1971

By Craig S. Compton

The failure of the immediate roof or "roof skin" between installed primary and secundary roof supports causes hundreds of injuries and, on average one or two fatalities each year in U.S. underground coal mines. Conventional roof supports cannot cover enough roof area to adequately control these relatively small, but very dangerous rock falls. The 2006 Mine Safety and Health Administration (MSHA) accident database lists a total of 542 ground fall injuries, including 10 fatalities. An analysis of the database suggests that 434 of the injuries and three of the fatali­ties can be attributed to roof skin falls (See Figure 2). The key to controlling falls of the immediate roof or roof skin is maximizing the area of roof coverage ilnd confining these relatively small loose rocks. Roof screen offers maximum coverage of the immediate roof. Depending on the size and configuration of the screen panels, coverage of up to 100% of the roof area is possi­ble. Screen also offers a first line of defense for machine operators working in the face area by confining or deflecting small rocks that can come loose during mining or roof bolt installation. Figure 1 shows an example of the protection screen provides dur­ing bolt installation. Although the benefits of screen are well-known, mining com­panies in some areas of the U.S., mainly Northern Appalachia and the Illinois basin, are not convinced that roof screen is the best tool for dealing with roof skin control issues. The logistics of material handling, possible ergonomic injuries to workers, and the costs associated with installation are delaying the acceptance of screen as an on-cycle roof support tool. Other mines however, have concluded that installing roof screen can be cost-effective when compared to the cost of lost time accidents, training of replacement workers, or returning to already developed entries for the cleaning and rebolting process.

Jan 1, 2009

By Charles H. Atkinson

The Rio Blanco massive hydraulic fracturing demonstration has been undertaken by the Bureau of Mines, Atomic Energy Commission, and a group of 15 industry participants. CER Geonuclear Corp. has been retained as program manager to evaluate the stimulation effects of very long fractures, suitably propped open in thick sections containing multiple intervals of low-permeability gas-bearing sands. The zone of interest for this demonstration includes Fort Union and Mesaverde sands from about 5,800 to 8,.200 feet deep in Rio Blanco County, Colo., about 1 mile from the site of the May 1973 triple nuclear detonation aimed at stimulating production from the same reservoirs. Drilling the test well and evaluating the reservoir prior to fracturing was funded by Government participants; fracturing and production testing will be funded by industry. The test well has row been completed at a total depth of 8,170 feet, and data obtained from logs, cores, production and drill-stem tests indicate reservoir conditions to be less favorable for gas production than anticipated. Structural position is lower than expected, resulting in higher water saturation than was determined for the same sands at the nuclear fracturing location. The lower sands of the Fort Union sequence appear to have higher shale content than has been encountered in other wells in the area. Despite the likelihood that gas productivity will be undesirably low following stimulation, the industry participants decided to proceed with the stimulation program with the thought that the resulting data would be useful. The success of the stimulation test probably will have to be judged by production increase rather than by production volume.

Jan 1, 1975

By Harvard Eng

An industrial survey was made for the Missouri Basin Field Committee of the Department of the Interior to determine the type and quantity of water-borne mineral wastes and the water requirements of metal-processing industries in the basin in Kansas and western Missouri. Data are presented on metal-processing plants visited through June 30, 1959. Most of the plants were in the greater Kansas City area. This report is to be supplemented with a similar publication on other industries, including those producing sand and gravel, coal, petroleum, and chemicals. In 1958, 19 million pounds of waste materials was discharged from metal processing industries. Approximately 14 million pounds of this waste was in the form of ferrous sulfate, and 2 million pounds was ferric phosphate. Galvanizing, other hot dipping, and automotive industries contributed the greater part of iron compounds wasted; some of this waste occurred as sludge that was not discharged to water courses but was hauled to refuse dumps, podium was present in nearly all industrial wastes, and the total of more than 900,000 pounds constituted one of the larger material losses. Although small in quantity, electroplating and allied coating wastes contained metals that were expensive when originally purchased.

Jan 1, 1961

By H. J. Heinen

Malononitrile [CH2(CN)2J, which forms a carbanion in basic solutions, was investigated as a potential leachant for gold and was shown to be an effective extractant in alkaline pulps. Malononitrile was comparable to equal molar quantities of sodium cyanide (NaCN) in leaching gold from an oxide ore and yielded 10 to 20 percent higher recovery in leaching a refractory carbonaceous ore, although dissolution was slower with malononitrile than with cyanide. Complete recovery of the gold from the pregnant solutions was achieved by coprecipitation with a lead salt on zinc dust; the leachant was shown to be capable of regeneration and recycling a limited number of times. Addition of an anion-exchange resin to the carbonaceous pulp containing malononitri1e increased gold recovery from 67 to 95 percent. Some malononitrile derivatives were also shown to be gold solvents.

Jan 1, 1970

By J. M. Gomes

The Bureau of Mines has investigated the occurrence and recovery of by-product heavy minerals from sand and gravel operations as a means of assessing the Nation's resources. Sand samples from 63 locations in central and southern California were treated to yield heavy-mineral concentrates. The mineral compositions of the concentrates were characterized by chemical and mineralogical examinations. Additional large quantities of concentrates were prepared from selected deposits that contained significant quantities. Beneficiation studies were performed on these concentrates to recover individual mineral products. Gold was recovered by amalgamation; platinum-group metals and radioactive minerals by flotation; magnetite, ilmenite, and chromite by magnetic and high-tension separation techniques.

Jan 1, 1980

By H. E. Peterson

This report revises an earlier publication by the Bureau of Mines on tungsten analytical procedures and expands the coverage by including appropriate procedures for the critical impurity elements that commonly occur in tungsten ores and concentrates (13).3 The basic methods described are not original, but many of the modifications to improve reliability and sensitivity were developed by the Bureau. Gravimetric and colorimetric methods currently used for the determination of tungsten in ores, mill tailings, and concentrates are described. Colorimetric procedures are preferred for low concentrations of tungsten, whereas either procedure is satisfactory for moderate concentrations. Conversely, a gravimetric method is preferred for the determination of tungsten in concentrates.

Jan 1, 1963

By G. M. Potter, F. S. Wartman, M. D. Schmid

"In matte smelting of copper it has been established that the sulphpr present will combine with copper as long as the latter is present, and that thereafter it will combine with iron. The Cu-Fe ratio in the matte is determined by the Cu-S ratio, presumably owing to the much greater affinity of copper for sulphur or, expressed thermodynamically, the greater stability of copper sulphide in contact with silicate slag. Now, the work of Fournet and of Schütz, which is quoted in many elementary metallurgical texts, indicates that manganese ranks ahead of copper in its affinity for sulphur. Hence, we might expect that manganese could be concentrated from its admixture with iron. Compounds by matte smelting, and Rotts / has patented such a process. This greater affinity of manganese or sulphur is used to advantage in iron metallurgy, also, in which it is well-known that sulphur will combine with manganese and separate from metallic iron as manganese sulphide. Manganese sulphide,however, is quite soluble in silicate slags. 5/ The loss of manganese in slag in any attempted matte smelting is therefore great.If this solubility of manganese sulphide is slag is a physical one and the reaction MnO + FeS MnS + FeOIs substantially complete, then it might be expected that the addition of copper sulphide, which is almost entirety insoluble in slag, would serve to extract the manganese sulphide with the formation of a manganese-copper matte on the other hand, if an equilibrium exists in the above reaction, a copper sulphide layer would displace that equilibrium in one direction or the other, according to whether iron sulphide or manganese sulphide were more soluble in the matter layer."

May 1, 1937

By A. A. Campoli

Retreat pillar mining concentrates stresses on workings directly outby gob areas, which can result in coal mine bumps. The development of bump-control design criteria by the U.S. Bureau of Mines was furthered by data from a novel bump control mining method at the Olga Mine, McDowell County, WY. The pillar splitting, retreat mining system induced large pillar pressure increases and roof-to-floor con-vergence. Roof-to-floor convergence monitoring proved to be a valuable tool in evaluating the pillar splitting mining method and localized destressing techniques. Maximum strain energy storage in chain pillars appears to have occurred just prior to the first of four split cuts. At that point a 15-ft-wide, highly fractured perimeter confined the core of the 55-by 70-ft pillars, permitting the pillar core to support tremendous pressures. Splitting the chain pillars into two 17.5-by 70-ft wings removed the confinement load, resulting in pillar yield. Thus, the pillar splitting mining method successfully redistributed the weight of the roof away from the pillar line. Shot fire and auger drilling destressing techniques aug-mented the pillar splitting mining method by redistributing the weight of the roof.

Jan 1, 1989

By A. R. Taylor

Low-temperature heat capacities of cesium chloride (7° - 300° K) and cesium iodide (13° - 300°K) were measured with an adiabatic calorimeter. The heat-capacity measurements were analyzed graphically to determine smooth values of heat capacity, entropy, enthalpy function, and free-energy function at 10° K intervals and at 273.15° and 298.15° K.

Jan 1, 1963

By Manuel Gomez

The mean and the standard deviation were used to describe general sulfur and ash populations as well as specific populations of these variables from one coal seam. Both the mean and the standard deviation were incorporated in the exploration process to determine the number of drill cores necessary for seam evaluation and to guide the sequential drilling plan. Probability regions were computed to establish a basis for predicting probable ranges of average sulfur and ash concentrations that may be expected upon continued or future drilling. A computerized plot program was utilized to interpolate sulfur and ash concentrations between grid points. The plot program, which is essentially a moving average technique, permits a rapid evaluation of sulfur, sulfur forms, and ash spatial distributions as a drilling program progresses sequentially. This information, in the form of contour plots, can be made available to both the mining engineer and the fuel technologist in advance of mining to outline reserves, to improve selective mining, and to anticipate preparation facilities.

Jan 1, 1972

By Dean E. Bluman

The Bureau of Mines investigated the convective heat transfer coefficients for recirculated suspensions of 30-micron glass beads in inert gas. Coefficients for the suspensions were not significantly higher than coefficients for the pure gas. Reynolds numbers of the suspensions were 20,000 to 35,000; solids loadings ranged from 0.0 to 0.7 pound per pound of gas. Comparison of the results with published data showed the direction of heat flow to have no effect at the test conditions.

Jan 1, 1967

By A. A. Sonnek

A simple, portable helium analyzer was developed primarily for field use. Its utility lies in making preliminary surveys before exact analyses are required. The analyzer is based upon chromatographic principles; that is, separation of gas mixtures resulting from variable retention times of the components with respect to a separation medium (column-packing material). It uses thermistors for sensing detectors, a dry battery as source of power, and a micro-ammeter for indicating helium concentration. The absolute accuracy of the instrument depends upon the recency and care with which the instrument is calibrated with a standard gas. The unknown gas should be analyzed immediately after calibration, and another calibration should be made before another unknown sample is analyzed. The instrument is simple to operate, requiring approximately 15 minutes, after calibration, to determine the helium content of a natural gas sample. Although developed primarily for helium determination, the analyzer possibly can be used for other analyses that can be performed at ambient temperatures.

Jan 1, 1965

By Frank G. Schwartz

The Bureau of Mines developed a rapid test method for predicting the stability of motor gasoline during long-term storage. The amounts of gum and inorganic residue formed in 13 gasolines during a l6-hour oven test at 200° F were compared with the amounts formed in the same gasolines stored at 110° F, and analyzed following 8-, 16-, 32-, 44-, and 52-week storage periods. Satisfactory methods were developed for predicting gum and inorganic residue formation during fuel storage periods as long as 32 weeks at 110° F, the approximate equivalent of 5.7 years at 80° F. The only data required to apply the methods are the amount of gum and inorganic residue formed, and the amount of oxygen that reacted, during a l6-hour oven test. A direct relationship existed between inorganic residue formed during the oven test and during 110° F storage. Statistical treatment of the data showed predicted values were as reliable as determined values. By use of a modified Arrhenius equation, the 110° F storage time can be extrapolated to equivalent time at any temperature below 110° F. Thus by combining the stability prediction method with the mathematical extrapolation, the storage performance of motor gasoline for extended periods can be estimated at any temperature up to 110° F.

Jan 1, 1968

By B. W. Madsen

A nearly dormant copper sulfide pilot-scale experimental leach containing 8.7 tons of are was injected with oxygen to determine its effect on the copper-leaching rate. Prior treatment of the uncrushed 0.25-percent-copper, mine-run stripping material consisted of 461 days of acid ferric sulfate leaching, which extracted 47 percent of the total copper. The permeability of the bed had decreased, and the percolation rate had decreased from an initial 20 gallons to 0.8 gallon per square foot per day. Copper extraction had nearly stopped. After injecting oxygen into the ore column and leaching for 30 days, the percolation rate was increased to 6 gallons per square foot per day. In an additional 298 days of leaching, an additional 40.7 percent of the copper was extracted. The improved leaching after the use of oxygen is attributed to stimulated bacterial action, better oxidation, and increased permeability.

Jan 1, 1975

By H .. B. HUMPHREY, F. E. Cash

Sixty-one fatal accidents were reported in the mines of Alabama during 1930. This number is a decrease of 15 per cent as compared with 1929; however, production was 13 per cent and the man-hours worked were 16 per cent less than in the previous year. There were 21,731 men employed inside and 3,386 outside. Table 1 gives the comparative rates per million tons and per million man-hours for the United States and for Alabama for 1929 and 1930. These rates are based on figures published by the State and by the United States Bureau of Mines, with preliminary figures for 1930. (These sources of data are used throughout this paper.)

Oct 1, 1931

By C. R. Stephan, N. B. Greninger, J. R. Lipscomb

The U.S. Bureau of Mines and the U.S. Mine Safety and Health Administration (MSHA) are participating jointly in a research program to evaluate the strength characteristics and air-leakage resistance of various proposed seal designs for use in underground coal mines. The full-scale seals were constructed in the USBM's experimental mine at the Lake Lynn Laboratory, air-leakage tested, then subjected to pressure pulses of 20 psig or greater. bjected to pressure pulses of 20 psig or greater. In experiments prior to this study, seven seal designs using solid-concrete blocks were tested. Only the standard-type seal passed the explosion and air-leakage criteria. Tests also were performed on four seals constructed with low-density foam blocks. All four of these seal designs withstood the pressure pulse. In more recent studies, nine cementitious foam seal designs of varying thicknesses and densities were investigated. Six of the nine designs successfully survived the explosion overpressures. Six wood- block convergence seals also have been tested. The typical 3-ft-thick, wood-block seal design currently used in many coal mines did not maintain its integrity, in the absence of convergence forces, following the explosion test. Five modified wood-block seals successfully withstood the 20-psig pressure pulse. Based on these tests, three alternative seal construction materials, cementitious foam, low-density foam block, and wood, have been approved by MSHA for use in underground coal mines.

Jan 1, 1993

By Michael T. Nigbor

The Bureau of Mines assisted the Rocky Mountain Energy Co. in a pilot-scale in situ leaching experiment at Casper, Wyo., to determine if sulfuric acid can be used as a cost-effective alternative lixiviant (leachant) for uranium in situ leaching. This experiment, which lasted more than 2 years, is the first fully documented pilot-scale operation in which the leaching-restoration cycle was completed using sulfuric acid instead of the more common carbonate-bicarbonate leachant This report describes activities at the experimental site, presents extensive geochemical data from startup to site restoration, compares laboratory and field experiments, and discusses the environmental aspects of acid leaching. The data showed that sulfuric acid is apparently an effective leaching solution. Three to five grams of acid per liter of ground water resulted in a production solution grade of 80 to 100 ppm uranium. Restoration was successful, but required extended flushing. The pH was the last chemical parameterto return to baseline, requiring about 350 days. This was longer than was predicted in laboratory simulations. The data also showed that mobilization of toxic elements such as selenium, arsenic, radium, thorium, and molybdenum stayed within reasonable limits and quickly fell back to preleach concentrations during restoration.

Jan 1, 1982