Search Documents

By Leonard Obert

This Bur of Mines investigation considers the deformational behavior (creep) of pillars made from three quasi-plastic rocks--salt, trona, and potash ore. The first phase of this study considers the design of a model pillar suitable for creep tests; in the second phase, six model pillars prepared from salt from two sources, from trona, and from potash ore. The pillars in each group were subjected to a different but constant axial stress, and the axial strain was measured for 1,000 hours.

Jan 1, 1965

By C. Kenneth Eilerts

A method is described for controlling instability in finite-difference computations of liquid saturation near the borehole of a recovery well. Differences of pressure-and saturation-dependent variables are indexed offcenter, upstream and downstream alternately, to provide a stabilizing average. It was found that size of the time step could be increased by a factor of 4 without loss of numerical stability. Finite differences of the variables occur in a variety of relative numerical sizes and combinations. Those relationships of the differences that contribute to instability may be identified by the computing program in which they occur and modified to assist convergence of the computations and execution of the partial differential equations of liquid and gas flow.

Jan 1, 1971

By John H. Perry

The Bureau of Mines has developed several techniques for draining methane from coalbeds in advance of mining. Drilling long horizontal holes from an underground location is one such technique, which was successfully demonstrated in the Pittsburgh and Sunnyside Coalbeds. The same technique has now been applied in the Mary Lee Coal bed at Jim Walter Resources, Inc.'s No. 4 Mine, Brookwood, Ala., where two holes were drilled horizontally--one to a depth of 1,010 feet (308 m) and the other to 540 feet (165 m). The 1,010-foot (308-m) hole proved successful in degasifying a portion of the Mary Lee Coalbed. The hole drained methane for 1 year, during which time the initial gas flow of 200,000 ft3/d (5,663 m3/d) declined to 65,000 ft3/d (1,840 m3/d). Total gas production was 40 x 106 ft3 (1.1 x 106 m3). The gas was of commercial quality, with 98 pct methane and a heat rating of 990 Btu/ft3 (36.89 Mj/m3). The methane emissions from the faces of the mine section advancing into the degasified zone were reduced by 60 pet. The 540-foot (165-m) hole was terminated prematurely when it became impossible to maintain an open hole. Because of caving, very little gas was drained through this hole.

Jan 1, 1982

By Leonard J. Prosser, Joseph Cervik, John H. Perry

The Bureau of Mines has developed several techniques for draining methane from coalbeds in advance of mining. Drilling long horizontal holes from an underground location is one such technique, which was successfully demonstrated in the Pittsburgh and Sunnyside Coalbeds. The same technique has now been applied in the Mary Lee Coalbed at Jim Walter Resources, Inc. 's No. 4 Mine, Brookwood, Ala. , where two holes were drilled horizontally--one to a depth of 1,010 feet (308 m) and the other to 540 feet (165 m). The 1,010-foot (3083) hole proved successful in degasifying a portion of the Mary Lee Coalbed. The hole drained methane for 1 year, during which time the initial gas flow of 200,000 ft3/d (5,663 m3/d) declined to 65,000 ft3/d (1,840 m3/d). Total gas production was 40 x lo6 ft3 (1.1 x lo6 m3 ). The gas was of commercial quality, with 98 pct methane and a heat rating of 990 Btu/ft (36.89 Mj/m3). The methane emissions from the faces of the mine section advancing into the degasified zone were reduced by 60 pct. The 540-foot (165-m) hole was terminated prematurely when it became impossible to maintain an open hole. Because of caving, very little gas was drained through this hole.

Jan 1, 1982

By Michael R. Norland

Surface and subsurface stabilization of mining-related wastes through revegetation depends upon the physical, chemical, and biological condition of the waste following mining. Mining disturbances can significantly alter the soil physical, chemical, and biological characteristics of a site, reducing or eliminating mycorrhizal fungi from the soil. Mycorrhizae are economically and ecologically important because they can alleviate environmental stresses caused by lack of proper soil condition and because they are vital to stabilization of mining waste by increasing plant survival and biomass through increased nutrient and water uptake. This report discusses some of the ecological factors that may affect mycorrhizae-plant associations on mining-related wastes and provides general information on mycorrhizae inoculation technology.

Jan 1, 1993

By Alton B. Cook

The practice of using partly depleted oil reservoirs for gas-storage operations is proving successful. Moreover, this practice provides a method of secondary oil recovery when gas is cycled at full-storage reservoir pressure. Because of the relative newness of this operation, a study was undertaken to assist engineers in developing improved gas-injection and production procedures and in calculating the amount of gas needed for completely repressuring reservoirs. This paper is the third in a series reporting the progress of a study by the Federal Bureau of Mines of reservoir performance during complete gas repressuring and gas cycling. A procedure for estimating secondary oil recovery by this method is also under study. One report (7)3/ describes the laboratory equipment. The other report (8) gives (1) data on the New York City field, Clay County, Tex., which has been converted to gas-storage operations; (2) laboratory data from research with a model oil reservoir, in which primary production, complete gas repressuring, and gas cycling for the New York City field were simulated; and (3) theory to explain reservoir performance during gas repressuring.

Jan 1, 1961

By Dennis A. Hansen

The solubility of anhydrous aluminum chloride in solutions of titanium tetrachloride and vanadium tetrachloride was determined as part of a re-search project-by the Bureau of Mines to make a homogeneous alloy sponge of titanium, vanadium, and aluminum. Solubility curves were established using an autoclave at 75°, 100°, 125°, and 150° C. The solubility of AJC13 in TiC14 is 0.2 wt pct at 75° C; it increases to 18.3 wt pct at 150° C. The data concur with data from earlier researchers of this bi-nary system for 75° to 125° C. For the VC14-AlC13 binary system the solubility of AlC13 is 0.1 wt pct at 75° C, increasing to 1.6 wt pct at 150° C. For the TiC14-AlClrVC14 ternary system the solubility of AlC13 decreases from the values found with a pure TiC14-AlC13 system to the lower values found with a pure VC14-AlC13 system at the respective temperatures.

Jan 1, 1986

By Gerald W. Elger

This report describes development of the fusion-leach crystallization precipitation process for producing a hafnium content feed material for hafnium-zirconium separation plants. Mixtures of zircon, potassium silicofluoride, and potassium carbonate (or potassium chloride) were fused to prepare soluble potassium zirconium hexafluoride-potassium hafnium hexafluoride salts. High extraction of these salts was obtained by countercurrent leaching the fused material in dilute hydrofluoric acid. About one-half of the hafnium was recovered in hafnium-enriched mother liquor by cooling clarified lead: liquor to crystallize most of the zirconium salt. Additional hafnium was recovered from the primary crystals in a multiple dissolution-recrystallization step. Hafnium-enriched oxides having a hafnium-zirconium ratio of more than three times that of zircon were precipitated from the combined mother liquors. The hafnium and zirconium recoveries in the precipitate were 83 and 24 percent, respectively. About 71 percent of the zirconium and the remainder of the hafnium were recovered in potassium zirconium hexafluoride crystals of low-hafnium content.

Jan 1, 1966

By Liane L. M. Kacinuck

This U.S. Bureau of Mines publication is intended to provide mining industry representatives and regulatory authorities with a reference package dealing with studies on hydrology and underground mine subsidence. An annotated bibliography and a list of additional sources are given and represent references published prior to June 1993. Ninety-two references ware identified and 72 obtained for assessment. Annotating the references included evaluating the study methodology and summarizing the basic results. The references are also compiled based on geographic location to aid the user in identifying articles of particular interest.

Jan 1, 1994

By W. P. Yant

[At the majority of mines where flame safety lamps are used either as working lights or as a means of detecting gas, no check it made on this condition of the various parts of the lamp and their assembly other than a visual ink inspection. Although this inspection should be made carefully in view of tae serious consequence that may follow Vie use of a faulty lama, In many instances the inspection is of a perfunctory nature. The Bureau of Mines has therefore designed a small box or gallery for testing lamps for defects and improper assembly before they are taken into the mine. The test simulates the condition when a lamp is extinguished by its introduction into an explosive mixture and the operator attempts to relight the wick while the lamp contains the explosive mixture. This test is more rigorous than merely subjecting a lighted lamp to an explosive methane-air mixture. In the latter test the products of combustion tend to blanket the propagation of flame from within the lamp to the exterior, especially if there are defects at the top of the gauzes. Moreover, when the lighted lamp is subjected to an explosive methane-air mixture the methane builds up slowly within the lamp until the lower inflammable limit is attained, whereupon a feeble explosion occurs within. If the nonlighted lamps is first filled with the methane-air mixture that gives the maximum violence and is than ignited, the dampening effect of products of combustion is obviated and the strain on defects is]

Jan 1, 1930

By J. R. Thoenen

The objective of this circular is threefold: First, to describe briefly the various modes of occurrence of sand and gravel. Second, to emphasize the need for adequate prospect¬ ing and exploration prior to the expenditure of funds for development and plant construction. Third, to describe various methods of prospecting and exploration and their application to the several modes of occurrence of sand and gravel. Sand and gravel may be found in nearly every county or township in the United States. Commercial deposits, however, are by no means so widespread. The introduction of concrete and the consequent impetus given to consumption of gravel and sand aggregates has seriously depleted deposits in some congested areas. Increasing re¬ strictions in the specification requirements for marketing sands and gravels have further narrowed the economic areas. On the other hand, the combination of increasing transportation costs and decreasing selling prices has forced the decentralization of gravel production. As a result smaller, intermittently operated, and widely scattered portable or semiportable unit plants have been encroaching on the territory formerly supplied from centrally located pits with large tr.atment plants. Generally speaking, the small portable plant can not produce any great variety of ma¬ terials to as exacting specifications nor as economically as the large permanent plant.

Dec 1, 1932

By BUREAU OF MINES

This summary of State laws on explosives was compiled primarily to ascertain what subjects relating to their control have been acted upon by each State legislature and , in general , how they have been treated . It does not include any legislation passed after 1942 , or any proclamations , regulations , or administrative orders . It does not purport or attempt to be authoritative . If any problem arises involving interpretation of the statutes of any particular State , the original source must be consulted for the exact words used by the legislature . This summary , however , will be useful in determining whether relevant statutes exist , and in locating thern quickly, with a minimum of effort . It will be of value also in comparing statutes in one State with similar statutes in other States to determine what construction has been placed upon them by the courts of these jurisdictions or to contrast the varying provisions of many States upon a similar subject . To make these comparisons easier , the statutory provisions for each State have been grouped under several major topics in outline form . Although this sometimes has resulted in disruption of the continuity of individual acts , the increased general clarity and availability of comparable sections have more than justified the procedure followed ,

Jul 1, 1943

By Earle S. Burnett

This report outlines the experimental procedures for using a Burnett apparatus to obtain compressibility coefficients for multiphase, multicomponent fluid mixtures. The conventional Burnett method is described briefly whereby multiphase compressibility data can be obtained by first determining the compressibility factor, Z, as an isothermal function of pressure alone. Then starting at conditions of temperature and pressure where Z is known, the fluid is cooled at constant volume to some lower temperature at which the resulting pressure is measured, and a corresponding value of Z is obtained from a fundamental relationship between compressibility factors, pressures, and temperatures at constant volume. The isochoric treatment of the fluid, extended to still lower temperatures and along other isochors, eventually results in compressibility determinations for the whole two-phase system thus covered experimentally.

Jan 1, 1963

By George A. Bell

This paper reviewing the leaching practice of the New Cornelia mines of the Calumet & Arizona Mining Co. at Ajo, Ariz., is the first of a series being prepared by the Bureau of Mines on leaching methods and costs in the various mining districts. ACKNOWLEDGMENTS The author acknowledges the assistance of T. G. Chapman, consulting engineer, and E. D. Gardner, supervising engineer of the Southwest Experiment Station, Bureau of Mines, Tucson, Ariz.

Jan 1, 1930

By A. C. Johnson

This paper is one of a series being prepared by the Bureau of Mines on exploration, development, mining methods and costs at various mines in the United States. It describes such methods at the Lincoln tungsten mine of the Wah Chang Mining Corp., Lincoln County, Nev. The purpose of these reports is to promote development and conservation of our mineral resources by disseminating technologic information on mining methods, practices and costs. The Lincoln mine in Lincoln County, Nev., in the southeastern part of the [tate], was acquired by the Wah Chang Mining Corp., in April 1951. Mining methods and costs are of special interest at this property because of the low costs and good production record achieved through a well planned program of exploration, development, and exploitation. Operations were discontinued in July 1957 after the Federal Government suspended the tungsten purchase program.

Jan 1, 1959

By D. R. Hanson

This Bureau of Mines study examines the acoustic vibrational spectra of rock slabs in the range of 0 to 5,000 Hz. The power spectra of so-called drummy rocks were found to be diagnostically enhanced in the range of 200 to 1,000 Hz. Comparison of the power in this band with that in a band from 3,000 to 3,500 Hz provides a quantitative measure of rock stability. A prototype field instrument was designed, constructed, and field-tested. This battery-powered instrument computes the power contained in the two frequency bands mentioned, compares the magnitude of these two quantities, and displays a number that is related to the detachment of the block tested. Field tests show that this instrument is capable of giving reliable measurements of block stability under conditions of noise and dust that would seriously degrade the accuracy of normal sounding techniques.

Jan 1, 1985

By Jingcheng Li

Currently many underground coal mines worldwide have installed or been planning to install a tracking system to trace miners mainly for their safety. Although many systems have been reported functional, a lack of sophisticated and systematic error correction methods apparently is still an issue for them; often it results in a low system resolution. To improve the system resolutions, this paper introduces two position adjustment methods for mine tracking systems. The first is an entry-matching method that optimally adjusts an off-course tracking device to the closest tunnel (entry). The second is a distance measurement adjustment method that accurately adjusts the position of a tracking device along an entry according to a measured distance from the device to a reference point. The coplanar node-path network mine model is used as the foundation for the development of these two methods.

Jan 1, 2009

By R. H. Sprute

This report describes a feasibility study to consolidate coal waste sludge in a 100-acre pond by applying direct current between floating and buried electrodes. The study was conducted by the Bureau of Mines under a cooperative agreement with Washington Irrigation and Development Co., located near Centralia, Wash. Part 1 covers results of laboratory tests at the Bureau's Spokane Research Center and a small-scale field test at the cooperator's coal preparation plant in western Washington. The process is efficient and cost-effective when power is applied at low current density. A proposed system, fully described in part 2, has electrodes covering 21 acres of pond surface radially arranged around a central power platform. Densification of pond contents would require 2 to 3 years of treatment. Total cost of equipment, labor, and material is approximately $500,000.

Jan 1, 1982

By J. F. Barkley

Under the procedure of the American Standards Association, with the American Society for Testing Materials as sponsor, the Sectional Committee on Classification of Coals has arrived at the classification of coals by rank as shown in Table 14/. The standard explains the term "agglomerating" used for classification under physical properties, as follows: Agglomerating Index. - Coals which in the volatile-matter determination produce either an agglomerate button that will support a 500-g weight without pulverizing, or a button showing swelling or cell structure, shall be considered agglomerating from the standpoint of classification.***. Pending the adoption of a method by the American Society for Testing Materials, the coke-button grading test5,/ afforded by the examination of the residue in the platinum crucible incident to the volatile matter determination, shall be used.

Jan 1, 1937

By O. H. Metzger

This is one of a series of papers being published by the Bureau of Mines on mining areas and districts in the Western states. It describes mining and milling practices in the vicinity of Wickenburg in Maricopa and Yavapai Counties, Ariz. ACKNOWLEDGMENTS The author acknowledges the aid and cooperation of the operators of the mines visited. Reports of geologists and engineers who previously visited the area were drawn upon freely. Individual acknowledgments are made in the text.

Jan 1, 1938