Search Documents

By Theodore L. Turner

This Bureau of Mines report describes calcination of kaolinitic clay in a direct-fired 2-1/2- by 24-ft rotary kiln at 750° and 775° C. Methods for preparing kaolin feed materials and characterization of calcined products are discussed. Approximately 99 pct of the alumina in a typical eastern Georgia kaolin was soluble in HC1 after calcination at either 750° or 775° C.

Jan 1, 1982

By Michael G. Zabetakis

Vaporization of a solvent into an airstream at temperatures above the flash point of the solvent is hazardous if vapor is liberated at a rate that is sufficient to produce a flammable mixture. In may operations, the formation of such a mixture is prevented by rapid diluton of the vapors with air. The minimum air requirements for the dilution process are determined by the composition of the lower limit mixture at the temperature and pressure of interest. Because limits of flammability cannot always be calculated with sufficient accuracy for a proposed operation, they .rust often be determined experimentally. The present Bureau of Mines investigation was prompted by an application in which the lower limits of flammability of a number of solvent mixtures were required over a range of temperatures at atmospheric pressure. These limits were to be used along with available solvent-vaporization-rate data to establish minimum airflow rates needed to prevent the formation of flammable mixtures in an industrial process. Lower limits of flammability were determined for a number of mixtures containing methyl ethyl ketone, tetrahydrofuran, toluene, ethyl alcohol, and ethyl acetate in dry air-at atmospheric pressure and temperatures between 16° and 200° C. The experimental values were found to be in good agreement at with those predicted by Le Chatelier's law; variations with temperature were in fair agreement with those predicted by a modified Burgess-Wheeler law.

Jan 1, 1962

By G. L. Mowrey, S. D. Maksimovic

An important element of the U.S. Bureau of Mines (USBM) mining research program is the development and evaluation of reliable coal interface detection (CID) systems. Commercially available CID sensors based on natural gamma radiation (NGR) are only applicable if the immediate roof is composed of shaley material. The USBM has made numerous underground and laboratory measurements using several NGR systems approved for installation on mining machines by the Mine Safety and Health Administration. In addition, two small handheld NGR instruments were used to make comparative measurements. Underground NGR measurements in 10 different coal seams, potassium-uranium-thorium radiometric analyses on samples from 16 seams, and chemical analyses of coal and rock for correlation with NGR counts were made. Laboratory test results on the effect of air gap and sample thickness, size, and weight on the NGR measurements, as well as general results of the various NGR systems, are discussed.

Jan 1, 1995

The Aluminum Company of America (Alcoa) announced plans to shut down production at the remaining two potlines at its Point Comfort, Texas primary aluminum smelter due to the increased costs of natural gas. Total capacity of the facility, which had been partially closed since 1976, was 185,000 tons per year representing 3.6 percent of current capacity in the United States. There were practically no price movements in March on 99.5 percent aluminum ingot, with producers at 53¢ per pound and dealers, 48¢-48.5¢. BISMUTH The March selling position of U.S. producer metal was held at $3.50 per pound. In contrast, east coast dealers and traders adjusted their quotes from $2.55-$2.60 to a wider range of $2.40-$2.60.

Jan 1, 1978

By D. L. Paulson

The Bureau of Mines is investigating pyrometallurgical and chemical methods for extracting copper from sulfide ores under conditions that provide for control of gaseous and solid emissions. Under this program, a new electrothermic reduction process was developed to produce blister copper after collecting essentially all of the sulfur by a single-unit operation. The process feasibility was indicated by a laboratory-scale investigation that demonstrated chalcopyrite concentrate can be roasted to less than 1 percent sulfur and that the resulting calcine can be reduced with carbon to blister copper by a cyclic process in a single arc-smelting furnace. Pilot-scale tests in an 800-kV-A electric-arc furnace demonstrated that 98.4 pct of the contained copper can be continuously recovered as metal by operating at bath temperatures between 1,350° and 1,375° C. Smelting rates of approximately 225 lb of blend ft2 of bath surface/hr resulted in power consumptions of approximately 520 kW-hr/ton of blend. The blister copper that was produced contained less than 0.1 pct iron while the precious metals reporting to the copper product and gangue material elimination were similar to those in a conventional smelting operation.

Jan 1, 1976

By A. U. Miller

"Ventilation is one of the meet important factors in mining, although until recent years less thought has probably been given to effective ventilation than to any other one phase of mining. In the past, very little, if any, attention was given air courses until they became so constricted by falls that the volume of air was greatly reduced; and, in addition, the stoppings and doors were so poorly constructed that only a very small percentage of air reached the face workings.As a matter of fact, mines have been visited where the volume of air being circulated in certain sections was much larger than in others, and where the management was striving to increase the flow of air in those sections with the least air current, believing the ventilation to be deficient. After sampling and analyzing the return air from the various sections in such mines it has been found that the quality of the air in certain places with the largest flow was more impure than in some of those with the least flow.In past years, practically all mine fans were operated by steam-driven engines supplied with steam from the mire boiler plant. No check was made on the steam consumption or the power cost of operating the fan, therefore the management had very little if any definite information as to cost of ventilating the mine.With the increased use of electrically-driven equipment in mines electricity is being used more and more to drive mine ventilating fans, and since in many instances the current is purchased from central power plants operators have come to realize that in many cases the cost of operating the fans is very high. Some engineers estimate that it ranges from 20 to 50 per cent of the total power cost of the mine. This information, together with the fact that mines are now being developed on a larger scale, requiring larger quantities of air for the men to dilute the gases liberated, has caused the large progressive companies to make, a more comprehensive study of mine ventilation, resulting in a decided improvement in the quality and quantity of air at the face workings, as well as reducing materially the ventilating costs."

Oct 1, 1930

By R. W. Watson

A belt-wearable self-contained self-rescuer (SCSR) manufactured by the CSE Corp. and designated the "SR-1OO" was evaluated for safety in the underground mine environment by the U.S. Bureau of Mines. The evaluation consisted of laboratory tests on the chemicals contained in the unit and field trials to simulate the mine environment. This report summarizes the test results and compares the results with those from earlier tests with chemical and compressed oxygen self-rescuers. It was concluded that the new SCSR did not pose any different or more severe hazards than the earlier units. In view of the mine-proven safety record of the SCSR's now in service, no reason could be found to disallow use of the belt-wearable unit.

Jan 1, 1991

By William J. Campbell

The purpose of this investigation was to extend the analytical services which are required for Bureau of Mines programs in developing and evaluating high-purity materials. Determination of trace elements in minerals and ores as an aid in geochemical evaluation and prospecting was considered. Serious consideration should be given to the merits of using the avail- able fluorescent X-ray spectrographic instrumentation and techniques for determining trace elements. Limits of detectability for trace elements in metal, oxide, solution or mineral samples range from 0.1 to 100 p.p.m, depending on the element being determined, overall sample composition, and the complexity of the X-ray spectra; limits of detectability range from 0.01 to 1 microgram for elements that have been preconcentrated by a chemical or physical process, for example, by ion-exchange membrane.

Jan 1, 1962

By F. P. Haver

The Federal Bureau of Mines developed a 10,000-ampere cell to determine the economic feasibility of producing high-purity electrolytic titanium from mill scrap or offgrade sponge. Operating variables were investigated, matetial handling procedures were established, and the cost of electrorefining titanium was determined. The prototype cell produced premium-grade metal (<100 Brinell hardness number (B.h.n.)) from very impure Kroll sponge at a processing cost of less than $0.60 per pound. Refined metal was deposited at the cathode in the form of coarse (85 percent plus 34-mesh), hexagonal crystals of a titanium when the cell was operated an 850° C. A cathode current density of 1,000 amperes per square foot and a molten sodium chloride electrolyte containing approximately 5 percent by weight of soluble titanium were used. In continuous operation, at the optimum number of ampere-hours, (40,000), the current efficiency averaged slightly less than 60 percent. It was possible to supply large enough amounts of electric current for electrolysis to maintain the temperature of the bath, thus reducing overall power consumption to less than 5 kilowatt-hours per pound of metal refined.

Jan 1, 1961

By Mandius C. Lundal

This report describes the work done to develop a coal mining machine to increase productivity and recovery from thin seams beyond the highwall, in addition to decreasing the miner&apos;s susceptibility to to highwall hazards First, radar transducers were adapted to measure coal thinkness and detect rock and coal interfaces; Then, the radar was incorporated into a cutterhead with steering controls. Next, visual displays were designed to show cutter position in the coal seam, and anticipated change in coal seam inclination, Finally, development of a telemetry system made remote control of the cutterhead possible. Simultaneously, a high-performance extended depth (HPxD) auger machine was designed with an automatic system to handle 600 ft of 36-in, diameter dual spiral flight conveyor sections. A two man crew controls all operations from a weather conditioned cab outside the VDZ, either at night or day time. As a primary mining tool, working 4000 hr/yr (2 shifts/day) recovering 60% of the coal 600 ft beyond the highwall, productlon to 500,000 ton/yr can be achieved. Volume I provides an overview of machine, systems and productivity.

Jan 1, 1977

By Victor R. Spironello

The Bureau of Mines has studied slags associated with ferrous melting, to evaluate substitutes for the auxiliary flux mineral, fluorspar. A waste material recovered from alumina reduction cells, "used potlining," was tested in an 18-in-ID basic-lined cupola and in a 1/4-ton, pilot-scale, basic oxygen furnace (BOF). One potlining fraction, No. 1 cut, is a carbonaceous (graphitic) material and represents the bulk of the entire cell lining. The other fraction, No. 2 cut, is a refractory backup. These materials contain significant quantities of fluorine and other elements fn various compounds. The potlining fractions were blended in ratios believed representative of available materials. Both lump and pelletized forms provided extremely fluid slag. No adverse effects were found on furnace performance, chemistry or strength of the metals produced, or the environment. Fluorine recovery in the slag and fluorine losses to the scrubber water and solids were about the same as when fluorspar was used. There was apparently no lining loss from the cupola, but there was lining attack in the BOF. Since the fluidizing ability of potlining is due in part to sodium and other elements such as aluminum and silicon, less fluorine is needed in the slags when potlining is used.

Jan 1, 1983

By Henry M. Harris

The roll forming of oxide powders was studied in a Bureau of Mines investigation to find the conditions and parameters required to make satisfactory ceramic strip. High-quality porous or dense alumina, zirconia, and porcelain shapes were made by sintering strip roll-formed at room temperature from powders containing minor amounts of binder and water. Strips with thicknesses of 0.04 to 0.08 inch and bulk densities from 40 to 90 percent of theoretical densities were made. The parameters most important to formability were particle size, condition of the powders, and roll gap. Other factors affecting quality were speed and surface condition of the rolls, amount and type of binder, water content, and sintering conditions. Ceramic strip was formed at rates up to 78 feet/minute, which is 13 to 23 times faster than reported by previous investigators, and forming was done in a simple and inexpensive roll unit. Reshaping the strip was possible by cutting, grinding, shearing, and stamping. The following innovations were developed that allow roll processing not normally possible with ceramic powders: (1) Fine-sized powders were made into strip by preparing these as partially sintered granules; (2) thick strip was formed by pressure feeding powders into the rolls; (3) flexible strip was made using a rubber-base bonding agent; (4) corrugated strip was formed on shaped rolls; and (5) porcelain strip was densified and reduced in thickness by rerolling while hot.

Jan 1, 1970

By Robert I. Fujimoto

The work described was conducted to develop standards for the application of wire rope clips on wire rope. These standards include optimum number of clips and clip nut torques for wire rope sizes 1/4 through 2-1/4 inches, when used for forming an eye attachment in wire rope. Wire rope test specimens with clip attachments were load tested on tensile testing machines to determine an effective combination of clip nut torques and number of clips for each size of wire rope to develop efficiencies above 90 percent of the catalog ultimate rope strength.

Jan 1, 1973

The Bureau of Mines analyzed the cycle of secondary gold to determine the quantity of gold not being recovered from scrap, and to identify areas for research to increase the supply of gold from scrap. Secondary gold in 1967 was estimated to be 2.4 million troy ounces; this excludes secondary gold which is recycled within consuming plants. Firms contacted included consumers using about 41 percent of the gold in 1967, And refiners that recovered about 90 percent of the secondary gold. Results of the study indicate that loss of gold is small, and refiners and consumers are accelerating programs designed to reduce recovery costs. With the increasing generation of low-grade industrial scrap, research is needed to improve present recovery techniques and to develop methods to accelerate the flow of secondary gold back to supply.

Jan 1, 1970

By J. P. BONARDI, C. W. Davis, R. B. Moore, J. W. MARDEN, S. C. Lind, J. E. Conley

The rare metals are becoming increasingly important to our industries. Rare-metal alloys have properties which indicate that we are only on the threshold of the possibilities of their utilization, not only in making nonferrous alloys, but also as special steels. Not only are their uses broadening rapidly, but the metals are affecting our industries in other ways. The oxides and some salts are used as pigments; others have medicinal value. The pure metals are made into filaments for incandescent lamps, and targets for X-ray tubes. By their efficient use in alloys, the weight of automobiles is reduced, • and the wear and tear on tires and roads is thus minimized; in machine shops they help to give greater efficiency to tools and reduce production costs. Their development has marked a milestone in the progress of civilization. There has been considerable uncertainty regarding analytical methods for the rare metals. A great deal has been published, but the weak and the strong points of the various methods have not been investigated as carefully as is needed. The Bureau of Mines at its Rare Metals station in Colorado necessarily had to do a great deal of analytical work in connection with the metals covered by this bulletin, which aims to give the results of the experience so acquired. No claim for much originality is made, although some published methods given have been modified, and some new ones have been developed by members of the staff. The principal methods available were studied critically, and it is to be hoped that the work will assist those interested in analytical work in connection with the metals named.

Jan 1, 1923

By M. R. Geer

Efforts to evaluate washery performance are nearly as old as the art of coal cleaning, and in former years there was no uniformity in either the methods used or the basic terminology employed. This situation, and the con- fusion it bred, prevailed until about the time of the First International Coal Preparation Conference in 1950, Largely because of the interest of the French coal research organization Cerchar, the subject of evaluating performance was given prime importance at this conference. As a result, there is now a much greater degree of uniformity in terminology and methods of expressing cleaning results. The International Standards Organization currently is working toward international standards of terminology and methods that should improve the situation even more. The various criteria that are used to evaluate the performance of coal- cleaning equipment fall into three categories, depending upon the extent to which they are dependent on the density composition of the raw coal; some are directly dependent, others are only indirectly dependent, and still others are substantially indenpendent.

Jan 1, 1962

By G. G. Morgis

In carrying out the provisions as set forth by an Act of Congress (36 Stat. 369) approved May 16, 1910, effective July 1, 1910, and the amended Act of February 25, 1913, (37 Stat. 681), the Bureau of Mines, among other activities, conducts inquiries and scientific and technologic investigations concerning mining with a view to improving health conditions and increasing safety and disseminates the general information gained by these studies. Through the medium of these publications, the causes as well as the methods that have been found most satisfactory in combating undesirable conditions are brought to the attention of the mining industry. This bulletin describes health and safety reports that have been published for the period July 1, 1955, through June 30, 1961. Technical Paper 705 issued in 1948 contains a listing of all Bureau of Mines publications dealing with health and safety in the mineral and allied industries from 1910 through 1946; Bulletin 558 contains a bibliography of such reports that were issued from January 1947 through June 1955.

Jan 1, 1962

By Kathleen M. Kowalski

In emergency management, the effects of stress on the performance of emergency personnel, typically have been ignored or regarded as too enigmatic to quantify. This paper discusses the concept of Critical Incident Stress in responders to emergencies. It presents the rationale for considering stress as a significant factor in the management of emergencies. It is proposed that Critical Incident Stress Debriefing in a disaster can improve the effectiveness of response teams on site, their turnaround time on site, and post-disaster time off the job. Critical Incident Stress intervention also can mitigate potential deleterious emotional effects associated with emergency work. This paper, prepared by a U.S. Bureau of Mines researcher, offers some ideas to the mining industry in general, to mine rescue team trainers, and to developers of program simulations on the specific issue of how people, time, materials and space may be factored into a plan for emergency management. The impact of stress on emergency workers is, presented as a missing component in present emergency management models.

By B. K. Shibler

During a research program to develop improved methods for recovering elemental sulfur and useful sulfur compounds from secondary source materials, the technical literature was searched for pertinent articles on processing methods. This report summarizes results of the literature survey and describes the more important processes that have been used or suggested for recovering sulfur and sulfur compounds from all non-Frasch sources. The bibliography presented represents a survey of the available English language literature on the subject through 1958, with particular attention focused on the period 1950 through 1958. Engineering Index and Industrial Arts Index were the principal guides used in the survey of this period. Chemical Abstracts was used to a limited extent to identify a few key foreign articles and patents. The Sulfur Symposium (4)4 published in November 1950 by Industrial and Engineering Chemistry includes a broadly representative selection of the literature up to 1949. Therefore, this reference was used extensively to locate and list pertinent articles on processing methods reported in the period prior to 1950.

Jan 1, 1962

By George T. Faust

The petrographer engaged in examining the products resulting from the beneficiation of ores and rock minerals is constantly required to develop new means and methods of assaying microscopically the results of such operations. From time to time investigators have published descriptions of apparatus that have aided in solving problems in processes f physical separation. Thus, in 191.9, Coghill and Bonardi 31 published a paper covering the application of the binocular microscope and camera lucida to the microscopic analysis of pulverized ores. Similar work has been published by Schneiderhohn 4/, Schwartz 5/, and Head and his associates6/, 7/, 8/. The present paper goes further and considers application of the polarizing comparison-microscope to problems directly concerned with mineral dressing where it is desirable to compare analogous products, and in addition it suggests new uses in various related fields. This work was conducted under the cooperative agreements of the Southern Experiment Station of the Federal Bureau of Mines and. the University of Alabama.

Jan 1, 1940