Search Documents

By David A. Lipton

In 1983, U.S. Bureau of Mines personnel examined mines, prospects, and mineralized areas to determine the mineral resources in the Carrizo Gorge Wilderness Study Area (WSA). The 14,571-acre WSA, located 42 miles east of El Centro, CA, is underlain primarily by Mesozoic granitic rocks and pre-Cretaceous metasedimentary rocks. Six prospects were found within the WSA and two mines are adjacent to it. Mineral deposits within the WSA have had insufficient development and rock exposures for calculating resources. The WSA contains no identified mineral resources; however, further exploration may disclose gem quality minerals. Two mines adjacent to the WSA, the Pack Rat and Beebe Hole, have produced gem quality kunzite and aquamarine from pegmatite dikes. According to the owners, a significant amount of gem minerals have been mined here in the last decade. Based on past production and the characteristic minerals indicating gem-bearing pockets, additional pockets are likely. Similar pegmatite dikes occur from Mt. Tule to Carrizo Gorge and may contain gem-bearing pockets. Pegmatite dikes also occur in the WSA near Rockhouse Canyon, but contained few of the mineral associations indicative of gem-bearing pockets. Manganese occurrences north of the Beebe Hole and Packrat Mines and within the WSA contain low concentrations of manganese. Significant sand and gravel were not identified. There is no evidence of deposits of oil and gas, or geothermal energy.

Jan 1, 1985

The 53 countries that constituted Africa in 1993 accounted for a significant portion of total world output of a number of mineral commodities. For the continent as a whole, world shares of most commodities showed little change from those of 1992 although most output volumes showed a slight decline. There were no significant production increases, but there were significant decreases of cobalt and copper because of political instability in Zaire and production problems in Zambia, of chromite resulting from cutbacks in South Africa and Zimbabwe, and of phosphate rock owing to a lower output by producers in general. (See tables 1 and 2.) Among the most significant mineral commodities produced in Africa, ranked by portion of world production in 1993, were diamond, cobalt, chromite, gold, phosphate rock, manganese ore, uranium and petroleum. Others of importance in world trade were andalusite, antimony, asbestos, bauxite, coal, copper, fluorspar, lithium minerals, platinum-group metals (PGM), titanium minerals (ilmenite and rutile), vanadium, vermiculite, and zircon. Several of these-chromite cobalt, diamond, and manganese-were not produced in the United States.

Jan 1, 1995

By Christopher Mark

This proceedings volume contains papers presented at W U.S. Bureau of Mines (USBM) technology transfer seminars on New Technology for Longwall Ground Control. These seminars were conducted in Washington, PA, on April 12, 1994, and Denver, CO, on May 10, 1994. The papers herein describe several new, highly practical USBM technologies now available for ground control in longwall mines, including lie Coal Mice Roof Rating (CMRR), cable bolts, the MULSIM/NL model, and the Wood Crib Performance Model. Other significant topics addressed include longwall panel layout, coal pillar design, horizontal stress in longwall mines, roof support selection for gate entries, and ground control monitoring.

Jan 1, 1994

By Fred N. Kissell

In This Chapter [The explosibility of methane gas mixtures Effect of pressure and temperature on explosibility Less common sources of methane ignitions The amount of methane stored in coal Forecasting the methane emission rate Layering of methane at the mine roof When the recirculation of mine air is hazardous The importance of higher air velocity in preventing methane explosions and Mine explosions, barometric pressure, and the seasonal trend in explosions] Dealing with methane in mines and tunnels requires knowledge of the circumstances under which dangerous accumulations of methane are likely to occur. This knowledge involves the properties of the gas itself, an awareness of where these accumulations are likely to occur, and facts on how methane mixes safely into the mine air. The other chapters in this handbook address the handling of methane under a variety of specific circumstances, such as at continuous miner faces or coal storage silos. This chapter addresses some broad concepts that serve as a foundation for the suggestions provided in other chapters. THE EXPLOSIBILITY OF METHANE GAS MIXTURES Methane entering a mine or tunnel often enters as a localized source at high concentration. Figure 1–1 depicts a cloud of methane being diluted into a moving air stream. In this illustration, methane enters the mine from a crack in the roof. As the methane emerges from the crack, it progressively mixes with the ventilation air and is diluted. In the event that this progressive dilution reduces the concentration from 100% to 1%,2 as shown in Figure 1–1, the methane passes through a concentration range of 15% to 5%, known as the explosive range. In the explosive range, the mixture may be ignited. Above 15%, called the upper explosive limit (UEL), methane-air mixtures are not explosive, but will become explosive when mixed with more air.

Jan 6, 2006

By D. E. Shanks

The Bureau of Mines surveyed a variety of inorganic ion-exchange materials to determine their suitability for removing valuable accessory elements and troublesome contaminants from metallurgical process and waste streams. Most of the materials, which included molecular sieves, heteropolyacid salts, and hydrous metal oxides, did not give adequate separations, did not have the necessary stability in strong acids or bases, or were not in a physical form suitable for ion-exchange use. Many of the suitable inorganic materials, especially the hydrous oxides, were capable of cation exchange with high capacity only in basic conditions, which caused hydrolysis of most of the cations tested. Multivalent anions, such as arsenate and phosphate, were easily removed from acidic solutions by hydrous oxides. Hydrous zirconia was the best material for this purpose. Multivalent anions were not easily des orbed because of compound formation; therefore, conventional ion-exchange techniques could not be employed. As an alternative approach, hydrous ferric hydroxide was used as a filter material to remove arsenate and phosphate from acid solutions. One gram of arsenic was removed from solution for each 20 g of ferric hydroxide. Ferric hydroxide is preferable to hydrous zirconia for use as a filter material because of low cost.

Jan 1, 1983

By Gerald T. Homce, James C. Cawley

Arc flash generally refers to the dangerous exposure to thermal energy released by an arcing fault on an electrical power system, and in recent years, arc flash hazards have become a prominent safety issue in many industries. This problem however, has not been effectively addressed in the mining industry. MSHA data for the period 1990 through 2001 attributes 836 injuries to “non-contact electric arc burns”, making it the most common cause of electrical injury in mining. This paper presents results from several elements of a recent NIOSH study of arc flash hazards in mining, and provides information and recommendations that can help reduce these injuries. Characteristics of past arc flash injuries in mining are first outlined, such as the electrical components and work activities involved (based on MSHA data). This is followed by a review of important concepts and terminology needed to understand this hazard. Next, methods for identifying, measuring, and managing arc flash hazards on a power system are covered, with emphasis on recommendations found in NFPA 70E, Standard for Electrical Safety in the Workplace. Finally, results are presented from a detailed arc flash hazard analysis performed on a sample mine electrical power system using IEEE 1584-2004a, focusing on components and locations presenting severe hazards as well as engineering solutions for reducing the risk to personnel. Index terms – electrical arcing, electrical burns, mining, arc flash hazard analysis

A stronger U.S. economy stimulated the domestic mineral sector in 1994. Metals demand was spurred by robust U.S. motor vehicle sales, while demand for major industrial minerals rose in response to highway and building construction. Domestic mineral and material demand is expected to increase in 1995, particularly if interest rates do not restrain the building industry and international monetary exchange rates remain advantageous to U.S. automobile manufacturers. Additional information on events, trends, and issues in the mineral and material sector is presented below and in the commodity sections that follow. Overall Performance Processed materials of mineral origin produced in the United States during 1994 increased to an estimated value of $360 billion. Domestic output of raw nonfuel minerals in 1994 was estimated at $34 billion, about 6% more than that of 1993. The value of U.S. minerals production has increased in 29 of the last 34 years.

Jan 1, 1995

By F. R. Lee

THE Bureau of Mines was established in July 1910 to conduct research and to establish standards for mining equipment and practices which would conserve human life, natural resources, and property in the mineral industries. Several lists of equipment approved by the Bureau as permissible for use in gassy coal mines have been issued since then. The lists covering all approved equipment except breathing apparatus and explosives have born consolidated into two publications: Bulletin 343. Permissible Equipment Approved to January 1, 1953, and Information Circular 8220, Permissible Mina Equipment Approved By The Bureau of Mines During 1953-62. The, purpose of this publication is to supplement Bulletin 343 and Information Circular 8220 with a listing of permissible equipment approved during 1963 and 1964. The schedule, (standards) under which equipment listed herein have been approved are, as follows (cities and dates of approval and revision are, given in footnotes) : Schedule 2F,3 schedule 6D,4 schedule 7C,5 schedule 8C,6 schedule 9B,7 schedule 10C,8 schedule 12D,9 schedule 22,10 schedule 24,11 schedule 25B,12 schedule 25B,13 schedule 29A,14 schedule 30,15 and schedule 31.16

Jan 1, 1966

By W. F. Hazen

This paper describing the mining practices at a 100 per cent mechanized mine working the Pittsburgh or No. 8 coal bed in eastern Ohio is one of a series being prepared by the U. S. Bureau of Mines on mining practices, methods, and costs in the various mining districts of the United States. The purpose of assembling this data is to place before those interested in the mining industry the methods employed and the cost data on the items involved in the winning of the coal and its removal to the railroad car at the tipple. Mining costs are governed by the mining method used, which is selected for its adaptability to local natural physical conditions such as the nature and thickness of the coal, its dip, the character of the roof and floor, and the thickness of the overlying strata.

Jan 1, 1929

By Robert G. Gibson, Joel D. Gibbons

Measurements and analyses were conducted of whole-body vibration aboard seven commercially available passenger and/or recreational vehicles: sedan; sport-utility vehicle (SUV); pickup truck; moving truck; motorcycle; all-terrain vehicle (ATV); and boat. The purpose of the testing was to measure and assess whole-body vibration exposure in a range of typical vehicle environments in order to gain understanding of typical exposure levels characteristic of activities of daily living. Vehicle models tested (and model year) were: Ford Taurus (1995); Jeep Cherokee Sport (2000); Toyota Tundra SR5 (2002); Ford F-350 (1997); Harley-Davidson Electra Glide Classic (2004); Yamaha Kodiak 400 4x4; and Steiger Craft Model 21 Montauk. All vehicles were tested with their standard factory-installed seats and were operated under a range of normal operating conditions and speeds typical of intended vehicle use. Methods The measurement, processing, analysis, and exposure assessment methods follow the guidance of generally accepted, national and international consensus standards relevant to the evaluation of whole-body vibration, including ISO 2631-1 [1] and ANSI S3.18 [2]. Seats were instrumented with low-mass triaxial accelerometers mounted in seat pads. Accelerometers used in the test are specified to have flat frequency response over the frequency range of 0.5 to 80 Hz, and all accelerometers were recently calibrated traceable to the National Institute of Standards and Technology (NIST). Seat pads were installed following guidance in the relevant standards [1, 2], with sensitive axes of the accelerometers following the standard coordinate system with respect to the seated occupant. (The x-axis represents fore-aft motion; the y-axis represents side-to-side motion; and the z-axis represents vertical motion with respect to the occupant.) Vibration data processing and analysis, including filtering, sampling, frequency-weighting, averaging, summation, and determination of basic and additional metrics followed procedures in the relevant standards [1, 2]. Digitized time series data were acquired and stored using a PC-based data acquisition system. Whole-body vibration exposure analyses were conducted via post-processing. During data processing, recorded periods of seat acceleration that were identified and verified as resulting from occupant-induced motion rather than vehicle motion were excluded prior to exposure analysis. The basic evaluation metric for whole-body vibration is the frequency-weighted root-mean-square (r.m.s.) acceleration, aw. The primary additional evaluation metric is the fourth-power

Jan 6, 2006

By Richard Quirk

This report describes methods and techniques employed by The Glidden Co. of Cleveland, Ohio, in explorating an ilmenite-bearing sand deposit in Ocean County, New Jersey, during 1960 to determine ore reserve potential and the feasibility of mining and establishing a milling plant on the property for the production of ilmenite concentrate. The property covered approximately 1,250 acres. Comprehensive sampling by water-jet drilling indicated the deposit averaged 20 feet in thickness and contained 4.5 percent heavy minerals, of which 80 to 85 percent was ilmenite and leucoxene. Average depth of the water table as determined by auger boring was 16.8 feet. Pilot plant tests indicated that circular concentrators in combination with spiral concentrators would recover at least 80 percent of the heavy mineral content of the sands. It was estimated that sufficient ore reserve tonnage had been developed to supply the company's Baltimore chemicals division, pigments department, with a suitable grade ilmenite concentrate for a period of 20 years at the present rate of pigments production. The property was designated as Lakehurst mine and plans are in progress for mining development and plant construction.

Jan 1, 1963

By D. B. Taliaferro, Thomas Jennings, C. M. Keithly

"INTRODUCTION This report describes the methods of development and operation and gives the results of controlled water injection into oil sands in Illinois. It is the third of a group relating to water-flooding operations in various States; previous reports have covered projects in Oklahome 5/ and Kansas.6/ Systmatic water flooding has been in progress, in these States, for more 10 years. In Illinois the Tide Water Associated Oil Co. has been injesting water into one or two wells on each of five leases in the Robinson Acknowledgments This study was made under the general supervision of R. A. Cattell, chief engineer, and H. C. Fowler, assistant chief engineer, Petroleum and Natural Gas Division, Bureau of Mines, Washington, D. C., and N. A. C. Smith, supervising engineer, Petroleum Experiment Station, Bureau of Mines, Bartlesville, Okla., and under the direct supervision of Ludwig Schmidt, senior petroleum engineer, Bureau of Mines, Bartlesville, Okla.The cooperation of the operators who are conducting water-flooding projects and who have made this report possible by furnishing data on their operations is gratefully acknowledged. The writers are grateful also to the following members of the Bureau of Mines for assistance in preparation and criticism of the manuscript: C. J. Wilhelm, Franklin, Pa.; and Gustav Wade, R. E. Heithecker, and Peter Grandone, Bartlesville, Okla. The illustrations were prepared by Helen Cramer, Petroleum Experiment Station, Bureau of Mines, Bartlesville, Okla."

Aug 1, 1944

By Daniel G. Di Canio

A computer based accident cost indicator model (ACIM) for estimating tangible costs of occupational injuries, illnesses, and fatalities in the U.S. mining industry is described. Studies performed to expand the scope of the ACIM to all mining sectors are presented. Validation of ACIM cost element estimation algorithms with actual costs of mining-related injuries and illnesses are presented. A study of the effect of a fatal accident on production in surface coal and metal/nonmetal mines is presented. The study is based on a sample of 15 fatalities in underground and surface mines. Evidence of significant long- term decline in postfatality production at 6 of 8 underground samples is presented. The average loss is shown to be 1.8% of annual mine production. A study of accident costs in U.S. mining from 1975 through 1981 using the ACIM is presented. The study shows that total annual costs increased from $180,000,000 in 1975 to $379,000,000 in 1981, a 15% annual increase after adjusting for inflation, with mining companies bearing 45% of the total and expected wage losses to mining families accounting for 42%. The study shows total costs of $12,400 per accident and $674,000 per fatal accident for 1981.

Jan 1, 1983

By Michel C. Frippel

This section of the Minerals Yearbook reviews the minerals industries of 45 countries: the 12 nations of the European Community (EC) (Belgium, Denmark/ Greenland, France, Germany, Greece, Ireland, Italy, Luxembourg, the Netherlands, Portugal, Spain, and the United Kingdom); 6 of the 7 nations of the European Free Trade Association (EFTA) (Austria, Finland, Iceland, Norway, Switzerland, and Sweden); Malta; the 11 Eastern European economies in transition (Albania, Bosnia and Hercegovina, Bulgaria, Croatia, Czechoslovakia, Hungary, Macedonia, Poland, Romania, Serbia and Montenegro, and Slovenia); and the countries of Central Eurasia (Armenia, Azerbaijan, Belarus, Estonia, Georgia, Kazakhstan, Kyrgystan, Latvia, Lithuania, Moldova, Russia, Tajikistan, Turkmenistan, Ukraine, and Uzbekistan).

Jan 1, 1994

By Gergely Markos

Uranium mill tailings represent a potential threat to the human habitat by containing large amounts of radioactive and chemically toxic substances in high concentrations. These: undesired components enter the human habitat in various pathways such as by erosion and water or air transport. The main objective of this investigation was to evaluate the actual movement and model the potential movement of contaminants by seepage of water from the tailings into the subtailings soil. This report represents various models of the movement of contaminants using both theoretical approaches and empirical evaluation of data available from other investigations. The data consist of field measurements and laboratory determi¬nations of major and trace cations, the dominant anions, pH, and Eh of moist solids, extracts, and waters from the tailings and surroundings. Evaluation and interpre¬tation of data were accomplished by using Eh-pH diagrams, various statistical methods and the WATEQFC computer program. Data analyses show that the critical area of investigating movement- is the interfaces between tailings and the external environment. The chemical differences at interfaces seem to result in a sink system for contaminants. The tailings-soil¬-water system shows extreme complexities because of chemical and physical hetero¬geneity of the system preventing the use of a single comprehensive model to represent real conditions. The validity of the simplifying assumption used has been shown and increasing complexity has been built into the models. Analogs of these models can be used for evaluation of similar systems.

Jan 1, 1981

By L. S. Harner

This paper which describes the milling practice at the Golden Cycle mill is one of a series of similar papers being prepared by the United States Bureau of Mines. The mill of the Golden Cycle Corporation, formerly known as the Golden Cycle Mining and Reduction Co., is located at Colorado Springs, Colorado, and has been operated since 1907. It is now and has been from its inception almost exclusively a custom mill.

Jan 1, 1933

By Peter Grandone

"INTRODUCTION The Bureau of Mines, recognizing the importance of knowing the evapor¬ation losses of aviation gasoline as larger quantities of this material must be stored, has made studies at a large refinery in the Texas Panhandle area during the past 13 months to determine the magnitude of the losses, by evaporation, under different storage conditions. Proper storage of aviation gasoline is very important, not only because large supplies are being stored for military use but because the specifications to which his fuel must conform are very rigid. Aviation gasolines that conform present-day specifications are blended from base-gasoline stocks (in some instances relatively pure hydrocarbons), each of which has different physical and chemical characteristics. Consequently, partial loss of any one of the more volatile components from the blended fuel results not only in material loss of the blended fuel but also may affect the characteristics or performance of the gasoline. One characteristic that has considerable influence or the vaporization tendency of gasoline is vapor pressure; and although the vapor pressure of aviation gasoline usually is lower than that of average commercial motor fuel, the quantity of certain components having relatively higher vapor pressure is greater in aviation gasoline, so that under prolonged storage the evaporation loss of these components may be appreciable."

May 1, 1943

By Robert S. Hill

"In November 1942, a preliminary report on the Swartz Mining District by John H. Soule, an engineer of the Bureau of Mines, recommended an exploratory program of diamond drilling. The existence of zinc and lead deposits in this region had been known for many years. In 1943 and 1944, the Federal Geological Survey made a detailed study of the same area. Later work done by the Bureau of Mines in this district followed the suggestions made by these geologists.3/In the latter part of 1944, Felix A. Vogel, Jr., another Bureau engineer, made a study of the Grey Eagle mine in the Kingston Mining District, a few miles northeast of the Swartz district, and his recommendations for diamond drilling were followed in so far as funds permitted. Drilling was started in October 1943 and was completed in June 1945.4/In its program of exploration of Mineral deposits, the .Bureau of Mines 'Ms as its primary objective the more effective utilization of our mineral resources to the end that they make the greatest possible contribution t national security and economy. It is the policy of the Bureau to publish the facts developed by each exploratory project as soon as practicable after its conclusion. The Mining Branch, Lowell B. Moon, chief, conducts preliminary examinations, performs the actual exploratory work, and prepares the final report. The Metallurgical Branch, R. G. Knickerbocker, chief, analyzes samples of ore and performs beneficiation tests. Both these branches are under the supervision of Dr. R. S. Dean, assistant director.With respect to this report, special acknowledgment for assistance is due to C. H. Johnson, chief of the Rolla Division, Mining Branch, and to various members of the Geological Survey."

Sep 1, 1946

By J. Walden, J. Rhoades, R. E. Miller, R. Gibbs, P. Boman

Accelerometers and pressure transducers, mounted in suspension components, can be used to monitor the ride of haulage trucks. Presently, it is difficult to tell what caused a jolt to the truck using either pressure or acceleration data alone. When information from a global positioning system (GPS) is recorded at the same time as shock pressures or acceleration data, the exact location of an event can be determined. Mine management can then determine what caused the jolt to the truck. This research is part of a National Institute for Occupational Safety and Health (NIOSH) project called "Engineering controls for reduction of jolting/jarring injuries in surface mines." NIOSH is investigating how the work environment of haulage truck drivers can be improved. The US Mine Safety and Health Administration (MSHA) notes that, between 1986 and 1995, 60% of the back injuries were to haulage truck drivers in metal/nonmetal surface mining. Personnel from Phelps Dodge suggested that combining acceleration data with information obtained from a GPS could generate results with a variety of uses. Therefore, researchers at the Spokane Research Laboratory (SRL) began investigating how to tie acceleration and GPS data together. It was originally thought that this tool would be used primarily for road and truck maintenance. However, as research progressed, it became apparent that it would also be useful in providing feedback about equipment operations and identifying unusual causes of jolting. Experimental approach Available components that function well by themselves were linked for the purpose of proof of concept. Using a Modular Mining Systems (MMS) product called Vital Signs, SRL researchers took an Aero-Marine Products (AMP) acceleration recorder and hardwired it to MMS Dispatch equipment already installed on a truck. AMP is one of several manufacturers of acceleration recorders frequently used to monitor freight during shipping. MMS Dispatch is used for production accounting and truck dispatching and uses GPS tracking. Through Vital Signs, an analog or digital alarm signal can be recorded. Steve Rhoades, of MMS, wrote unique code that links the Vitals Signs data and GPS location and stores this data in an ASCII log file. SRL researchers installed the equipment in a Caterpillar 793 haul truck. The result was a working prototype. Figures 1 and 2 show the instrument installation in the truck. Discussion From 8:30 pm on Sept. 14, 1998 until 6:50 am on Sept. 15 1998, 899 jolts above a threshold of 2 g (1 g is the acceleration of gravity. It is either 9.81 m/s2 or 32.17 ft/ s2.) were measured on the test truck. Some sections of the haulage road produced most of the events, while

Research 84 highlights significant studies conducted during the past fiscal year at Bureau facilities and offices. Readers who want more information about the projects and studies summarized here can contact the researchers whose names and locations appear with each summary. General information on Bureau of Mines programs is available from the Office of Technical Information, 2401 E Street, NW., Washington, DC 20241. A listing of principal officials, a location map of field facilities, and a selected bibliography of publications and patents issued on Bureau developments during the past 3 years are provided.

Jan 1, 1984