Search Documents

By Carlos Agreda

The rock blasting environmental impacts such as: flyrock, groud vibrations,airblast,and/or noise, dust and fumes are identified and mentioned. Some comments on the correction factors that might be taken into consideration to calculate the initial velocity and the maximum projection of the rock fragments are mentioned as well.

Jan 1, 1995

By Dale L. Ramsey

The Pinkerton Tunnel Open Cut Project is part of the National Gateway Clearance Initiative improvement project to achieve a minimum of 6.4 meters (21 feet) of vertical clearance along CSX Transportation rail corridor so that double-stacked intermodal railcars can be transported between Mid-Atlantic States and their ports to Midwest Markets in the U.S.

Jan 1, 2014

By D G. Dressler, Paul Yeager

A previously little-known facet of seismic frequency spectrum analysis is gaining significance. The frequency spectrum of seismic waves promulgated from blasting is a significant factor in causing blasting complaints and threshold (architectural type) damages.

Jan 1, 1987

By R R. Vendebeek

The continuing evolution of explosives has most recently introduced emulsion explosives and heavy ANFO's to the market place. An explosives engineer has a multiplicity of explosives to choose from: dynamites, slurries, water gels, emulsions, ANFO's, and mixtures of some of these products.

Jan 1, 1987

By C. B. Navalkar

The optimization of blast design under consideration is for the conventional driveways in under ground coal mines with respect to board & pillar workings in India. Basically The Blast Design includes following parameters: AA> Drilling Pattern. BB> Charging Pattern. CC> Material & Method Of Stemming. DD> Selection of type & quantity of explosives. EE> Initiation system & Blasting Sequence.

Jan 1, 2002

By T N. Hagan

Where explosion energy moves rock from the in-situ to its desired location without considerable assistance from digging and/or hauling equipment, good fragmentation is of minor importance. Maximum displacement must remain uppermost in the mind of the blast design engineer.

Jan 1, 1979

By Jay P. Tobin

This paper will address the legal standards applicable to construction blasting lawsuits and offer best practices suggestions for pre-blast inspections, documenting the construction blasting work, recordkeeping, and effectively participating and partnering in the defense of a construction blasting lawsuit.

Jan 1, 2015

By John F. Vynne

This paper will discuss the application of available monitoring technology on blasthole drills with the goal being to reduce costs and increase productivity. Case studies from the monitoring of blasthole drills in North American open pit mines will be used to illustrate the ability to meet these objectives.

Jan 1, 1997

By Erik K. Lauritzen, Jorgen Schneider, Niels Madsen

From 1986 to 1988 Kalaallit Tunisassiorfiat (KTU)/Gronlands Hjemmestyres Produktionsvirksomhed (the part of Greenland's own governing body which is in charge of production activities) has been responsible for blasting projects in the following 4 towns: Ilulissat/Jakobshavn, Qasigiannguit/ Christianshab, Qeqertarsuaq/Godhavn, Sisimiut/Holsteinsborg

Jan 1, 1989

By Charles A. Kliche

The Comprehensive Environmental Response, Compensation and Liability Act of 1980 (CERCLA) established a national program for responding to releases of hazardous substances into the environment. The funding mechanism for this program is the Hazardous Substance Response Trust Fund (commonly referred to as Superfund), which provides funding for the implementation of removal and remedial response actions.

Jan 1, 1997

By Norman Kramer, Roger Keller

The authors would like to thank Austin Powder Company for their technical support and input, specifically Stephen Harris, Jason Ryan, and John Capers of Austin Powder, without whose support this paper would not have been possible. Thanks are also extended to Nick Francis of Sandia National Laboratories and Jim Houseworth of Duke Engineering for their input regarding Performance Assessment.

Jan 1, 2000

By K R. Sharpe, A Davitt

CXA is currently evaluating, in co-operation with Inco Metals, a new idea in small diameter hole blasting - the Unidelay Nonel initiation system. In concept, the Unidelay system is a hybrid of the conventional multi-period Nonel system and the safety fuse assembly/igniter cord system. It combines the operational advantages of the latter, simplicity and flexibility, with those of the former, safety and compatibility with all commercial explosives.

Jan 1, 1982

By E Emery Jr Gray

A need for more delay periods other than those normally manufactured throughout the explosives industry rarely occurs. This paper will discuss one such incident from an analytical view through practical application.

Jan 1, 1976

By J Paul Tidman, Stephen H. Chung

One of the requirements in open pit gold mines is to minimise the mixing of ore and waste. Dilution can be reduced by choke blasting and control of the initiating sequencing. The authors have used the DMC computer model (developed at SANDIA) to examine the effects of timing and charge distribution on ore dilution. The model has been calibrated by measurements of vertical uplift derived from high speed videos made at the Dome Super Pit in Timmins.

Jan 1, 1997

By Qingshou Chen, Paul N. Worsey

It has been recently argued that rock strength has little effect on the final results of pre-split blasting and is of only minor importance when blasting rock in general. However, it can be shown that the maximum borehole separation for optimal perimeter blasting results with constant borehole and loading configuration is strongly dependent on the tensile strength of the rock.

Jan 1, 1986

By Raymond M. Dixon, Dale L. Ramsey

Upon being introduced to the MAGNETIC COUPLING concept,Balsinger,Inc. wanted to conduct field trials to explore the potential of Magnetic Coupling in the U.S.. Although the Magnetic Coupling Concept has been widely used, the U.S. proposed blasting criterion not previously addressed by the system. Modification to the system assembly and blasting accessories had to be made to make the system adaptable to our specific requirements. The field trials and system modifications are the basis of this paper.

Jan 1, 1990

By John A. Huber

At an underground limestone mine in the Central United States; there were plans for the installation of a limestone processing plant. The special design and layout of the plant called for the installation of a tunnel from the underground mine to the surface above. The dimensions of the tunnel would be 10 feet high, 20 feet wide, and would be 500 feet long on a 17 degree incline. The tunnel would be used for the transportation of raw stone to the surface by a conveyor. A second conveyor would transport processed limestone into the mine for storage, that would be loaded out for shipment later.

Jan 1, 1995

By Yoshiharu Tanaka, Keita Morooka, Masaaki Yamamoto, Katsuhiko Kaneko

Smooth blasting is the standard method for underground rock excavation, to reduce over break and remaining rock damage. We already utilized the high accuracy of the electronic delay detonator to investigate its effect on over break remaining rock damage, and surface smoothness. And we presented at 11th annual symposium on Explosives and blasting Research.

Jan 1, 1998

By Joseph W. Hejny, Marlyn G. King

Coal mining in the Powder River Basin has changed in recent years to accommodate the large quantity of coal produced. With strip ratios of one to one and up to three to one, extensive amounts of overburden have to be removed to get to the large thick seams of coal. Larger shovels and trucks have been implemented in the removal of this overburden. The addition of draglines and continuous miners have been added to increase the production of coal. Drills used today are capable of drilling up to 13.5 inch blast holes.

Jan 1, 1994

By Masanobu Morita, Koichi Kurokana, Kenji Hashimoto, Yoji Tasaki, Yukio Iida

"It has been the long desire of blasting engineer to realize the automatization of tunnelblasting to improve the safety and efficiency. As for bore hole drilling, the automatizationhas been achieved by the improvement of drilling machine. However, the firing process isstill depending on the hand-operation. We developed the wireless initiating system using amacrowave power as a step for automatization of tunnel blasting operation. In this paper,we present the outline of the wireless initiating system and the results of experimentalstudy of the wireless detonator which is key component of the system."

Jan 1, 1993