Search Documents

By Ruiyang Zhang, Ping Fang, Dezhou Wei, Shuling Gao

A CFD based numerical simulation of flow characteristics of hydrocyclone was conducted with different structural and operational parameters to investigate its distribution characteristics and influencing mechanism. The results show there exist several unsymmetrical envelopes of equal vertical velocities among both upward inner flows and downward outer flows in the hydrocyclone, and cone angle and apex diameter have remarkable influence on the vertical location of the cone bottom of the envelop of zero vertical velocity. It is also found that some tangential velocity isolines exist in the horizontal planes located in the effective separation region of hydrocyclone, and feed pressure has almost no effect on the distribution characteristics of both vertical velocity and tangential velocity of flow in hydrocyclone, however the magnitude and gradient of tangential velocity are made increased obviously, so as to make the high density particles motion velocity to the wall increased and to make the cyclonic separation effect improved. The simulation results also show when the apex diameter increased, the pressure of the fluid field decreased, however the pressure grads in the apex district increased, and the degree of changing is different as the cone angle, which showed some interactive influence of cone angle and apex diameter on the fluid field of hydrocyclone. While the feed pressure also has almost no effect on the pressure distribution characteristics, however the its magnitude and gradient are made increased accordingly, which can improve the separation accuracy according to particle density.

Jan 1, 2014

By Knut L. Sandvik, Erik Larsen

Crystalline silicon solar cells are the most important solar cells manufactured today. This will most probably remain the situation the next decade. The future silicon feedstock is most likely not reject from the production of electronic-grade silicon. There will probably be a more direct solar-grade silicon route, excluding the electronic-grade silicon "detour". Estimated global solar energy demand in 2001 required approximately 5,500 tons of silicon feedstock. This required 65,000 tons of quartz. If the trend continues, the solar energy demand in 2010 would require approximately 30,000 tons of silicon feedstock and 350,000 tons of quartz, although the need for quartz probably will be lower than this. Quartzite has been regarded as the most suitable primary raw material used in the silicon solar cell production chain. This may change as the raw material requirements for the production of metallurgical-grade silicon are most likely to change. In addition, quartz or other silica-containing minerals from other rocks may be of a higher purity or contain lesser amounts of the most harmful elements. This favours increased beneficiation of primary raw materials in the future solar silicon feedstock production chain.

Jan 1, 2003

By S. Serranti

The recycling of end-of-life concrete into new concrete is one of the most interesting options for reducing worldwide natural resources use and emissions associated with the building materials sector. The possibility to realize a larger re-use of silica aggregates from old concrete, strongly contributes to reduce environmental impact (reduced exploitation of natural resources, reduction of CO2 emissions, airborne dust production, etc.).To reach this goal, innovative processing techniques, as well as innovative sensing units and architectures have to be developed. In this perspective an analytical approach, based on hyperspectral sensing techniques, is proposed, discussed and critically evaluated in order to perform an automatic quality control assessment, finalized to maintain a high standard of concrete demolition waste, from the earliest stage of recycling to the further processing stages, according to the detected in-situ demolition waste characteristics. The paper deals with the analysis and the evaluation of the problems related to the integration of this approach with state-of-the-art demolition and building processes and procedures. Keywords: end-of-life concrete, recycling, hyperspectral imaging, NIR spectroscopy, quality control

Sep 1, 2012

By Harri J. Lehto, Marja I. Oja

Empirical models used for predicting the performance of screens on the basis of capacity, cut size, water split and grade efficiency curves were evaluated. This paper reports experimental results obtained with single-deck Derrick screens. The performance of the screen was tested with limestone in a separate screen set-up, in a pilot plant and in industrial scale test runs. The results of pilot plant experiments showed that the measured water split was higher than the measured bypass. This is an indication to that water flow does not entrain the same proportion of all fine particles present in the feed which is advantageous for screening. The experimental design for the industrial test runs was made on the basis of the pilot plant tests. Suitability of the existing models has been checked and accuracy compared. The tests showed that best grade efficiency model was the Rosin-Rammler model. An empirical model for the evaluation of the model parameters as a function of pulp density of the feed and the load of the screen is suggested.

Jan 1, 2003

By P. Latostenmaa, T. Hailemariam, M. Lundström, P. Halli

Doré process is unique way to treat precious metals in the copper electrorefining plant, since it uses anode slime as a raw material. In this pyrometallurgical process, also slag is produced together with Doré metal. However, the process is never ideal, and a part of metal is always lost into the slag. By using Doré slag as raw material for simply mineral acid leaching, some of the lost elements can be extracted and recovered, thus, increasing the sustainability and keeping metals in the circular economy loop. The Doré process itself is developed to convert almost all precious metals and PGMs in the Doré metal, leaving other elements into the slag fraction. The Doré slag consist of slag formers, such as borax and silica based minerals, but contain also traces of sealing materials. In addition, the Doré slag is rich in metals present in the anode slime, such as Cu, Bi and Sb, which are not converted into the Doré metal. There are only few published applications at the precious metal plants, where conservative grinding and flotation circuits have been utilized for the enrichment of valuable metals present in the Doré slag fraction (Godbehere, P.W., 1983; Segawa, C. and Kusakabe, T., 1996). However, the present study shows an alternative approach for the recovery of metals present in the Doré slag by hydometallurgical approach. The study focus on direct mineral acid (aqua regia) leaching of metals present in the Doré slag. The initial dissolved concentrations of Cu, Bi and Sb from Doré slag in the temperature range of 30-50 °C under oxygen purging with addition of 1 vol-% of H2O2 are presented. Chemical and mineralogical analyses were performed for the raw material, leaching residue, and leaching solutions in order to ascertain the leaching behavior of the metals of Bi, Cu and Sb.

Jan 1, 2018

By Girolamo Belardi, Silvia Serranti, Giuseppe Bonifazi, Roberta Palmieri

Ore textural and structural characterizations play a fundamental role in any preliminary study (i.e. comminution, classification, separation) addressed to the design and set up of beneficiation flow sheets. The possibility to utilise automatic tools able to perform a classification, and a quantitative description, of the mineralogical and petrographical characteristics of raw ore samples thus represents an important step to define, to control and to verify the entire set of parameters, ore-texture-related, that can affect the final beneficiation results. The procedure usually adopted is based on the analysis of polished sections and more in details the recognition of the different mineralogical species and associations and the measurements of some quantitative parameters estimating both the geometrical characteristics of each species and the possible spatial relationships between them. This approach, originally carried out by experts, utilising optical and/or electronic microscopy, was ‚replaced? during the years by more and more sophisticated devices integrating analytical facilities and acquired data processing. Such integrated analytical devices formed the breakthrough platforms into what is now known as modern Process Mineralogy. In this paper the possibilities offered by chemical imaging based devices and techniques, to perform ore minerals recognition/classification, and to perform their topological assessment, are presented. Tests have been carried out and are discussed in order to analyze the problems related to the development of suitable and low cost strategies addressed: i) to realize a full mapping of ore minerals/gangue inside selected samples, ii) to define the optimal data-flow handling to optimize the speed of processing versus the quality of the results and iii) to start to define logics and procedures finalized to implement innovative smart detection engines, chemical imaging based, for mineral processing addressed to perform both a preliminary characterization of the ore, at laboratory scale, and a further possible control of the different processed minerals flow streams.

Jan 1, 2014

By E. V. Bratygin, E. G. Dmitrieva

The aim of the research was to study the thermodynamic characteristics of high-temperature processing of ilmenite concentrate deposits "Central" in a neutral and oxidizing atmosphere, as well as its interaction with alkaline additives. The research was conducted using a scanning colonoscopy on thermogravimetrical analyzer NETZSCH STA 449 F3. A sample of the test material weighing 10 mg was placed in a crucible and heated at a rate of 10 °C/min to 1200 °C in argon or air. Studies have been conducted pure ilmenite concentrate and its mixtures with 5 % and 12.5% of sodium carbonate. The results of the analysis of the thermogravimetric curves it was found that the recovery of the concentrate carbon will come from ulvospinel, not pseudobrookite, and the reaction recovery is possible at temperatures above 900°C. While removing produced in the decay ilmenorutile of iron oxides in an inactive form, for example, iron (III) oxide, it is possible to reduce the quantity of the solution of ilmenite formed during the restoration of the melt anosovite. The analysis of data obtained during heating of ilmenite concentrate with sodium carbonate in concentrations of 5 and 12.5% transition pseudobrookite in ulvospinel is missing, it just breaks down into hematite and titanium oxide, which, in turn, react with N?2??3. It should be noted that increasing the concentration of sodium carbonate in the sample contributes to more complete interaction of iron oxides and N?2??3 with formation of ferrites of sodium. This can ensure full recovery of iron oxides in the concentrate, which is part of secondary ilmenite can not be dissolved in the melt formed by the lower oxides of titanium. In addition, the increase in the content of soda in the mixture significantly reduces the temperature of the initial melting point of the slag and facilitates the coagulation of metallic iron.The obtained results were used for laboratory studies of the solid-phase sintering of briquettes from ilmenite concentrate with additives of sodium carbonate and a reducing – coal, as well as for the development of technological mode of solid-phase sintering of the concentrate with the aim of obtaining product recovery with a titanium dioxide content of more than 75 %.

Jan 1, 2018

By Teemu Väyrynen, Matti Vilkko, Antti Jaatinen, Pekka Itävuo

"This paper shows that smooth and accurate feed-hopper level control is essential for consistent cone crusher operation. The objective of the paper is to define the best practices for tight control of cone crusher feed-hopper level. The paper discusses the challenges involved in a delay-dominant level control problem (specifically, dead-time-induced performance and stability issues, mass flow disturbances, process and actuator non-linearity) and proposes five corresponding control structures. The performance of the proposed control structure candidates is evaluated in a simulation study and, finally, a full-scale experiment is conducted for the best-performing candidate. The results of this study emphasize the importance of control structure selection. While the most obvious control structures failed to deliver the desired performance, the best result was achieved by using control structures that eliminate the conveyor transport delay (dead-time) from the control loop. In practice, the control loop dead-time can be eliminated by either using an actuator (variable-speed feed conveyor) that is connected directly to the feed-hopper, or by redefining the process boundaries closer to the used actuator (regulate the circuit mass balance instead of feed-hopper level). The presented control structures provide means to achieve a consistent cone crusher performance and size reduction. This facilitates efforts to improve the plant’s performance and increases the plant’s overall stability."

Jan 1, 2014

By M. Ito

Cobalt-rich ferromanganese crust and nodule ores from seamount areas contain volcanic and sedimentary rocks as substrate or nuclei and these ores require mineral processing to remove the substrate/nuclei rock before smelting. This paper reviews the results of jig separation and air table treatment for the coarse fraction and flotation and hybrid jigging for the fine fraction. Using these techniques substrate/nuclei rock was removed from the cobalt-rich ferromanganese oxide components. The mineralogical properties and metallurgical treatment methods including hydrometallurgical treatment of low grade ore is also reviewed.

Sep 1, 2012

By Kaustubh Joshi, Pradip, Beena Rai, Kesri L. Menaria, Venugopal Tammishetti

"Beneficiation of alumina rich iron ore slimes is a major challenge for the Indian iron ore industry. High alumina is deleterious for the performance of both blast furnace as well as sintering plants. Slimes generally contain 5 - 10% alumina, and hence despite assaying as high as 60% Fe, those are dumped in tailing ponds. The slimes are typically less than 37 microns. Selective flocculation of iron ore slimes using highly selective reagents is thus an option worth exploring. Our research is directed at employing state-of-the-art molecular modeling techniques for the selection/design of selective reagents for this separation. We have earlier reported our results on starch as a selective flocculant for iron ore slimes. In this paper, we present our results on the selective dispersion-flocculation of natural iron ore slimes using guar gum flocculant. With careful selection of various process parameters such as flocculant dosage, dispersant dosage, pH and settling time, we were able to obtain a concentrate assaying >66% Fe and <3.5% Al2O3 with an yield of 65 to 68% (recovery of iron values more than 70%) from a natural iron ore slime sample assaying 58% Fe and 7% Al2O3."

Jan 1, 2014

By I. Silin, H. Wotruba, J. Huben, A. Ognyanova

"With increasing shortage of raw materials, the beneficiation of ultra-fine ores will play a larger role in the near future. Many established process technologies do not yield satisfactory separation results for ultra-fine materials. Without selectivity, high-grade concentrates cannot be produced. The material at hand is a taconite which had to be ground to d(90) = 25 µm to guarantee liberation of the iron oxides. The comminution was done by High Pressure Grinding Roll (HPGR) and resulted in smooth surfaces and clear grain boundaries. This is an indication of selective grinding and mineral liberation. Further processing steps included selective desliming, magnetic separation as well as reverse flotation. INTRODUCTION During the last centuries, the processing of iron ores became increasingly important. The coarse-grained, so-called lump ores that are ready for direct usage in blast furnaces without further processing are becoming gradually less abundant. The processing of ultra-fine-grained ores, which in addition require a complex ore beneficiation due to the composition of the material, will progressively gain relevance with increasing resource shortages in the future (Arvidson, 2013). The term “ultra-fine” does not hold a precise definition in mineral processing. In this paper, “ultra-fine-grained” ores are defined by the required grind size for full liberation smaller than 20 µm. Many established mineral processing technologies do not yield satisfactory separation results for ultra-fine materials. Thus, they are limited in their application to produce high-grade concentrates suitable for sintering and pelletizing for direct reduction processes. The production of a high-grade iron concentrate (over 68% Fe) with low silica content (under 2.5% SiO2) is possible from both magnetite and hematite containing ore. In addition to the mineral processing technologies (magnetic and gravity separation, flotation), technologies for the liberation of fine-grained iron ores need to be developed and improved. In contrast to the conventional wet grinding circuit by means of tumbling mills, several future trends in dry and wet grinding and regrinding are already in use. These include technologies such as vibration mills (Palla®Mill), stirred media mills (Vertimill®), vertical roller mills (Loesche) and high-pressure grinding rolls (HPGR) (Jankovic, 2015). This study preliminary investigated the mineral processing of a low-grade, ultra-fine-grained, complex iron ore in a laboratory scale after dry grinding by HPGR to 90% < 25 µm without consideration of the grinding, milling, energy and classification cost."

Jan 1, 2018

By Stefaan J. R. Simons, Michael T. Spyridopoulos

In this paper the effect of humic substances (natural surfactants), electrolytes and solid particles on bubble coalescence, and as a consequence on froth stability, has been investigated. We formed two bubbles of equal size and forced them to collide using a novel experimental apparatus. The interactions were recorded by a high-speed camera, the images of which helped to determine the coalescence frequency and the coalescence time, as well as the mechanisms of the interactions. Two types of humic substances were used, along with three different electrolytes. Humic substances appeared to have a considerable effect on bubble coalescence, while the effect of electrolytes was minimal. Moderate and high hydrophobic glass spheres were used between two bubbles. Very hydrophobic spheres promoted fast bubble coalescence, while moderate hydrophobic spheres had no effect. We present data of coalescence frequency and time, as well as images of the coalescence events.

Jan 1, 2003

By Leon Lorenzen, Victor E. Ross, Anton W. Kleingeld

Key to successful innovation, whether at organization, industry or national level, is the alignment and utilization of resources in the most appropriate and efficient way. Innovation needs to be directed strategically, and it needs to be auditable in a systematic and integrated fashion. In the light of these considerations, this paper describes the construction and use of a topographical map of the innovation landscape. The purpose of the map is to provide a holistic view of the key factors that enable innovation (the so-called ’landmarks’), how well they are aligned to support a particular type/nature of innovation in the organization, and to identify possible gaps. The significance (importance) and height (performance) of the landmarks in supporting and enabling innovation within the organization is determined by means of a selfappraisal audit. The topography of the landscape derived thus is subsequently interpreted in terms of the organization’s particular innovation strategy and environmental context. The application of the Innovation Landscape Methodology is illustrated in a number of organizations within the Mining and Minerals Industry of South Africa. Important observations and conclusions regarding the strategic alignment of enabler strengths within these organizations are made.

Jan 1, 2003

By A. V. Abshilawa, D. G. Talakhadze, R. I. Sturua

"Processing of the tailings accumulated over the lifetime of Madneuli Copper Concentrator is an opportunity to extract additional salable copper and gold products. This paper presents a pre-concentration process for the valuable components (copper and gold) of the accumulated tailings. The developed process makes it possible to obtain a copper pyrite concentrate with a yield of 14.05%, copper grade of 1.36%, and recovery of 83.22% containing 3.78 g/ton of gold at a recovery of 84.31%. The bulk concentrate is produced by a combined process bringing together selective flotation to produce salable copper concentrate and hydrometallurgical processing of the selective flotation tailings to recover gold. KEYWORDS: FLOTATION, ALBION PROCESS, LEACHING, COPPER CONCENTRATE, SELECTION Madneuli Copper Concentrator, Georgia, was put into operation in 1975. Over its lifetime, 40 mn tons of tailings have been accumulated at the tailings storage facility (TSF). Sampling of the TSF has indicated that the average copper and gold grade is 0.23% and 0.56-0.65 g/ton, respectively. Accordingly, the TSF can be classified as a technogenic reserve. This paper discusses pre-concentration of valuable components using flotation, followed by processing of the bulk concentrate in the Albion process. Mineralogical analysis of the accumulated tailings showed that the main ore mineral is pyrite (11.71%). Copper minerals are mainly represented by chalcopyrite (0.7%). The main nonmetallic mineral is quartz (67.3%); sericite, chlorites, etc. also occur. Pyrite is present both as liberated grains and intergrowth. The absolute majority of copper minerals are found as intergrowth with pyrite, less often with quartz. Ore minerals are slightly oxidized. Chemical analysis results are shown in Table 1. Particle size distribution shows that the size class -0.2 mm - 0.045 mm has the highest grade of 0.85 to 0.97 g/ton of gold. Size class +1.25 mm has the lowest grade. Based on the chemical and mineralogical studies and particle size distribution, an optimized process was developed for pre-concentration of the valuable components prior to hydrometallurgical processing. Several gravitation, direct selective, bulk, and bulk selective flotation processes were trialed. (1,2)"

Jan 1, 2018

By O. Guven, I. Karaagaçlioglu, O. Ozdemir, M. Çelik

In this study, the effect of morphological properties such as shape factors and roughness of the glass beads on their flotation efficiency were determined using image analysis and profilometer methods. There is a considerable correlation between the shape factors, surface roughness and flotation behavior of the glass sample. These results indicate that as the particle shape is away from roundness and smoothness, it acquires more hydrophobicity.

Jan 1, 2014

By G. V. Sedelnikova

Biohydrometallurgical studies were performed on the sulfide gold-arsenic concentrate obtained in treatment of refractory ore from a deposit located in northern Russia. Gold is disseminated in sulfides-arsenopyrite, pyrite and antimonite (their content is 10.0%, 30.4% and 0.7%, respectively). Gold extraction is only 11.8% by cyanidation. Results are given for test bacterial oxidation of the concentrate in continuous mode at temp. = 28~32°C using mesophilic bacteria and at temp. = 32~38°C using the association including moderate thermophilic bacteria. The paper shows that the use of moderate thermophilic bacteria allows to speed up sulfide biooxidation and reduce its time to 96 hours compared to leaching at temp. = 28~32°C for 110~120 hours. The optimal range of pH = 1.5~2.0 of biooxidation process was determined where bacterial solutions are produced with the molar ratio Fe:As > 3 necessary for precipitation of hard-to-solve, environmentally safe arsenical precipitates. Electron microscopy showed that sulfide biooxidation results in liberation of disseminated gold with nanoparticle-level sizes. High sorptive activity of carbonaceous matter and other compounds of bacterial residues cause low gold extraction into cyanide solution ? 28.7%. 10% resin load makes it possible to extract 88.1% Au. Aeration of pulp in calcareous medium enhances extraction to 95.7% and decreases cyanide consumption from 17kg/t to 8 kg/t.

Jan 1, 2014

By Yury V. Kulikov, Rakan Rahbani, Arkady Y. Senchenko

"The relevancy of complex minerals treatment is constantly increasing taking into account mineral resources depletion. Different refractory ores and concentrates, oxidized and polymetallic ores, as well as metallurgical products (slags) can be assigned to such mineral type. The treatment of such products via conventional flowsheets requires considerable capital and operational costs and does not always provide high recovery level of valuable components into a saleable product. Therefore, considerable amount of ores and metallurgical products are not treated, or treated inefficiently. One of the most promising approaches that allows economic treatment of refractory products is their ultrafine grinding down to 5-20 µm with subsequent processing or hydrometallurgy. Horizontal bead mills - the IsaMillTM, developed by Xstrata Technology, received their wide application in mining industry. Standard testing is performed under laboratory conditions in an M4 IsaMillTM (volume - 4 liters) to define the parameters of fine grinding. This mill completely simulates the operation of full scale industrial mills up to 50 m3 in volume (up to 8000 kW motor). The paper describes fine grinding technology performed in bead mills, and the importance of testing according to a certified method for industrial equipment selection. The paper contains description of promising directions of fine grinding technology application for several projects in Russia and Kazakhstan."

Jan 1, 2014

By Ashish Kumar

High grade ore deposits in the world are fast depleting and the valuables in the low-grade ores are finely disseminated. The feed grade to flotation circuit is also declining. Attainment of suitable grind is preferred, which inevitably creates more fines of the gangue minerals to interfere with the flotation process because of the undue competition between the fines and the valuables for the collector ion adsorption. Besides the use of polymeric or long chain hydrocarbon depressants for the gangue mineral, microbial induced flotation also has potential to float minerals selectively. Thiobacillus ferroxidans and Thiobacillus thiooxidans adhere on the minerals to modify its surface properties and affect the minerals flotation acting as depressants. Hindustan Zinc has conducted laboratory studies to understand the adhesion of microorganism on the mineral surfaces and its impact on the selective flotation. The experiments were further designed to reduce consumption of depressing reagents for graphitic carbon, pyrite, and galena. Preliminary studies reveal that desired quality of concentrate can be achieved with reasonable recovery. Keywords: thiobacillus thioxidans, thiobacillus ferroxidans, bioflotation, microbial induced flotation

Sep 1, 2012

By V. P. Yakushkin, B. S. Ksenofontov

"Multistage model designed and used for more detailed description of floatation process. The study develops a new model of flotation kinetics description. It defines flotation as process that consists of several stages: air bubbles and particles are separate, air bubbles and particles form a raising aggregate, aggregate raises to froth layer. This description significantly differs from commonly used model, which is much simplified. The multistage model gives an in-depth description and considers different aspects of flotation. Experimental approval of the new model resulted in its accuracy.The model is to be used for description of all flotation processes’ kinetics of wastewater treatment. It helps in accurate designing of flotation treatment plants and may be used for further research of flotation process. Columnar flotation installation was designed by using multistage model. This installation consists of new tubular aerators with special ejectors, froth pressing system as well as unit of thin-layering lighting to catch microflotocomplex “particle – bubble”. Usage of tubular aerators allowed to aerate the overall volume of pulp. Due to use of special ejectors with longer mixing camera we state higher volume of small-sized floto-active bubbles. Use of multistage model allowed to optimize and get higher technological results of potash salts enrichment. Tests were conducted on centrifuges-floatation installation system. Meanwhile, froth concentrate contained mainly thin hydrophobic particles sized circa 0,1 mm. As a result we set that during floatation cleaning process of froth concentrate 95-98% of chloride potassium (KCI) is derived from foam.The final product satisfies production quality. Columnar floatation installation productivity was 17 – 21 m3/m2h, which is a high technological result. Columnar floatation installation is one of the best examples of concentrating equipment using nearly all technological indices."

Jan 1, 2018

By L. Ya Agapova

Emissions from pyrometallurgical processing of copper concentrates are usually subjected to wet scrubbing. The washing sulphuric acid so produced contains up to 0.2 g/L of rhenium, which is recovered by solvent extraction in the form of crude ammonia permeate (NH4ReO4). The mother liquor, obtained from the sulfuric acid wash, contains up to 35 g/L of rhenium and significant amounts of impurities. Crude rhenium salt is commonly processed by double recrystallization to produce marketable salt. A ton of high grade NH4ReO4 can be produced using 3.0-3.5 m3 of mother liquor. We propose an efficient technology of mother liquor pre-treatment aimed at removal of water-soluble organics with subsequent electrodialysis. Electrodialysis of mother liquor in a multichamber electrodialyzer resulted in the production of pure rhenium acid, from which a marketable NH4ReO4 is precipitated using ammonia solution. Multiple steps of recycling consisting of dissolution of NH4ReO4 salt, rhenium acid production from NH4ReO4 salt by electrodialysis and precipitation of NH4ReO4 from rhenium acid made it possible to upgrade the purity of obtained rhenium compounds by 1-2 orders of magnitude. A rhenium metal powder of 99.997% purity was produced by high-temperature reduction of high-purity NH4ReO4 with gaseous hydrogen. Rhenium metal powder of high purity can be produced from sulfate solutions of NH4ReO4 by non-platinum anode-based membrane electrolysis processes also. Keywords: rhenium, mother liquors, membranes, electrodialysis, rhenium acid, ammonia perrhenate, reduction, powder, electrolysis

Sep 1, 2012