Search Documents

By Dalia. R. Mohamed, Hisham H. Hafez, Marawan M. Shahien

"Construction activities in major projects that involve deep excavations necessitate the use of vertical walls surrounding the construction site to play an important role as earth retention system. The walls are usually partially penetrating impervious walls which can increase the efficiency of the ground water control system that usually consists of number of partially penetrating wells. The analysis and design of such system requires 3D numerical simulation. The aim of this study is to develop simplified semi-empirical approach to analyze and design such system. The analyzed model is a single well in a square site that is surrounded by impervious walls along the perimeter of the site in an unconfined aquifer. The results of the parametric analysis are presented in this paper aiming to assess and understand the factors that influence dewatering in terms of ground water or drawdown profile surrounding the well. The parametric analysis is carried out using the 3D finite difference software. The parametric analysis comprises with more than 550 cases calculated. The study involved the parameters; well penetration depth, impervious wall penetration depth, size of the construction pit, coefficient of permeability, well yield and well location or distance between well center to impervious wall edge.IntroductionThe presence of groundwater in a site may have impact on the construction processes involved during the course of project construction, especially those projects that involve deep excavations. Deep excavations, especially in urban areas, require the construction of supported walls all around the site perimeter to ensure the stability of the excavation. In most of cases, the constructed walls are relatively impervious. Depending on the ground and site conditions, the walls are not penetrating all the way down through to the bottom of the aquifer and thus the walls are partially penetrating walls. The presence of ground water necessitates the lowering of the groundwater to levels below the bottom of the excavation to ensure working in dry. This paper focuses on groundwater control systems that consist of deep wells inside square areas enclosed by impervious walls partially penetrating unconfined aquifers. The wells are partially penetrating the aquifer, as well. There are many factors or parameters that are related to the configurations of the components of the system that may influence the drawdown of a well in such groundwater control system. This paper is a part of a comprehensive study that aims to development of a simple method for estimating the drawdown of dewatering system of the described configuration. In order to achieve such a major goal, a 3D finite difference model is developed for the problem in hand. A comprehensive parametric analysis was then carried out to investigate the influence of all the parameters on the drawdown of a deep well in such groundwater control system. This paper describes the problem, the model, the parametric analysis including the involved parameters. The paper, then, demonstrate the results of the analysis showing the influence of the studied parameters on the drawdown of a single well."

Jan 1, 2016

By Siavash Mahvelati, Alireza Kordjazi, Joseph Thomas Coe

Deep foundations are often constructed as end bearing members with a significant amount of their capacity derived from bedrock. Sites with highly variable bedrock conditions therefore present a unique challenge when attempting to estimate the design elevation of deep foundations. Typical subsurface characterization techniques such as drilling, standard penetration testing (SPT), and cone-penetration testing (CPT) may fail to adequately establish top-of-rock elevation in geologic settings prone to karst and/or significant amounts of residuum, saprolite, and deformed bedrock. Seismic surface wave geophysical methods have been increasingly used to map bedrock topography in such settings. However, the current standard of practice for these methods introduces resolution limitations in spatially variable subsurface conditions due to averaging effects from the analytical framework used to process the acquired data. This study explores the use of a tomographic approach with full waveform inversion (FWI) to map top-of-rock elevations at a numerically simulated site representative of highly variable bedrock topography. Comparisons are made with seismic refraction (SR) and a dispersion-based multichannel analysis of surface waves (MASW) approach as more commonly used in geophysical subsurface investigations. The results highlight that FWI provides a superior estimate of top-of-rock topography than SR and MASW at a cost of a significant increase in the required computational resources and time.

Sep 8, 2021

By Siavash Mahvelati, Alireza Kordjazi, Joseph Thomas Coe

Deep foundations are often constructed as end bearing members with a significant amount of their capacity derived from bedrock. Sites with highly variable bedrock conditions therefore present a unique challenge when attempting to estimate the design elevation of deep foundations. Typical subsurface characterization techniques such as drilling, standard penetration testing (SPT), and cone-penetration testing (CPT) may fail to adequately establish top-of-rock elevation in geologic settings prone to karst and/or significant amounts of residuum, saprolite, and deformed bedrock. Seismic surface wave geophysical methods have been increasingly used to map bedrock topography in such settings. However, the current standard of practice for these methods introduces resolution limitations in spatially variable subsurface conditions due to averaging effects from the analytical framework used to process the acquired data. This study explores the use of a tomographic approach with full waveform inversion (FWI) to map top-of-rock elevations at a numerically simulated site representative of highly variable bedrock topography. Comparisons are made with seismic refraction (SR) and a dispersion-based multichannel analysis of surface waves (MASW) approach as more commonly used in geophysical subsurface investigations. The results highlight that FWI provides a superior estimate of top-of-rock topography than SR and MASW at a cost of a significant increase in the required computational resources and time.

Oct 1, 2021

By Ambarish Ghosh, Chitralekha Ghatak, Tanumaya Mitra, Tarun Sengupta, Sajib Das, Sankar Kumar Nath

"Currently construction of important structures like bridges, flyovers and high rise buildings in and around Kolkata are in full swing. These structures have mostly pile or well foundations. The design methodology and construction techniques are being employed keeping in view both the safety and economy of the project. The data presented in this investigation have been taken from Geotechnical Investigation report of Component B in connection with construction of Extradosed Cable Stayed Bridge over River Hooghly in Hooghly and Nadia district of West Bengal, India. The investigation site is located within close proximity of Eocene Hinge Zone which is being taken as the principal contributor of Earthquakes in and around Kolkata. Considering the importance of the project detailed and exhaustive geotechnical investigation has been carried out and site specific response spectra have been generated for analysis and design of the bridge. This paper presents site specific response spectra, liquefaction analysis and comparison of lateral load carrying capacity of pile using Winkler approach and IS 2911 guidelines.INTRODUCTIONPile foundations are used to transfer the load of the super structure through soft soil deposit to deeper bearing stratum by means of skin friction or end bearing or both. Pile foundations are regarded as a safe alternative for supporting structures in seismic areas and have been used for this purpose in non-liquefying as well as liquefying soils. But their design in case of potentially liquefiable soil is quite different from that of non liquefiable soil. In liquefiable soil the progressive buildup of excess pore water pressure will cause stiffness degradation and loss of strength which in turn will induce additional shear force and bending moment in the pile. The mechanism of pile behavior in liquefying soil has been investigated by several investigators in the recent years based on observations of pile performance during earthquakes and studies in the centrifuge and Shake Table tests. Exhaustive geotechnical investigation has been carried out along the proposed alignment of the Extradosed Cable Stayed Bridge i.e., along Baropara, Bansberia ROB, Ishwar Gupta Bridge, Saraswati River to collect disturbed as well as undisturbed soil sample, to develop average soil profile and to determine the design parameters. The proposed project site is very close to Eocene Hinge Zone, which is basically a strike slip fault, capable of generating an earthquake of Mw 6.7. Thus it is evident that the proposed Bridge needs to be designed considering the adverse geo-hydrological condition as well as the earthquake aspects needing special attention following the state-of-the-art technology as guided by relevant codes and published literatures. Considering the soil profile of these locations ground response analysis has been carried out using equivalent linear method to determine the site amplification. Site specific response spectra have been developed for the four zones and zone factors have been determined. The computed zone factors are 0.198g, 0.195g, 0.195g and 0.20g for the four zones respectively, much higher than the zone factor 0.16g, which is for zone III, as stipulated in IS 1893:2002."

Jan 1, 2015

By Dena Morgan, Emre Biringen

"Abstract This paper discusses the execution of pile installation and design issues at two environmentally challenging industrial sites in North America. Environmental regulations set constraints on the design and require versatility in choice of technology.For a proposed bridge, due to protected fish habitat, performing soil borings within 30 m of the creek embankment was prohibited. The limited subsurface profile indicated a thick upper layer of granular material, thus driving H-piles was considered. However, to limit generation of vibration and noise in the protected area, drilled piles had to be used. During execution, the subsurface profile differed from that in the borings 30 m away. Very soft, saturated silt was encountered at the bottom of the caisson and the length had to be redesigned very quickly while the contractor waited for instruction. For a new structure in uncontrolled fill area, performing soil borings was not allowed. It was known that a layer of peat was present in the area, but no information regarding the thickness and extent. The subsurface profile generally consisted of granular material overlying a thick compressible silt layer. Somewhere within the granular layer peat would likely be encountered. Franki piles were chosen to penetrate the peat and bear in the underlying granular material. During environmental sampling in the area, methane gas was encountered and Franki piles were no longer a viable option due to safety concerns. The foundation system was changed to steel H-piles driven to bedrock, which was more than 50 m below the ground surface and sloping. Rock shoes that would work to significant slopes had to be used in order to increase the likelihood of good embedment within the bedrock. Also, due to obstruction of an approximately 3 m thick debris field that was encountered in the upper granular soils, some of the piles had to be relocated and extra piling needed to compensate for such differences. The results of PDA testing to estimate compressive capacity and a series of lateral load tests are presented.INTRODUCTIONThe design issues that are encountered during construction can be quite problematic and have a significant impact on schedule. In order to avoid such impact on the project, a thorough subsurface investigation should be considered prior to design and construction. Better understanding of environmental regulations also prevents costly changes to the foundation design. This paper discusses the execution of pile installation and the design issues at two environmentally challenging sites in North America.BRIDGEDuring the subsurface investigation for a proposed industrial building complex, several boreholes were drilled within the footprint or in close proximity of various structures, with Standard Penetration (SPT) sampling of the upper coarse-grained soils (sand/gravel) and undisturbed sampling of the lower fine-grained soils (silt/clay). The SPT blow counts (N60) were corrected by a factor of 1.35 in order to incorporate the SPT automatic energy transfer ratio. When Modified California Sampler was used, a correction factor of 0.44 to 0.64 was also applied. N60 values were further corrected for gravel to avoid artificially high blow counts during the analyses due to spoon samples contact with gravel and cobbles, and the corrected values of (NG)60 (limited to a maximum value of 50 blows/300 mm) were used for design. The information from the SPT boreholes was then used to assess the subsurface conditions beneath the structures, as well as for a nearby bridge that was designed to cross over a creek. Since performing soil borings within 30 m of the creek embankment was prohibited due to the protected fish habitat, the investigation with regard to the bridge abutments was limited to two deep boreholes (B10-33 and B10-34) at the bridge location and two additional boreholes (B10-35 and B10- 36) located approximately 200 m upstream. The bridge location and two sets of boreholes are"

Jan 1, 2014

By Amr Al Degwe, Walid Jaber

"INTRODUCTIONNSCC International Ltd. carried out the enabling works and constructed the foundation system for the Emirates Pearl Tower and Bab El Qasr Hotel in Abu Dhabi. Emirates Pearl Tower is a joint venture project of TDIC- Tourism Development and Investment Company and ATLAS group, a leading telecommunication company in the UAE. Bab El Qasr Hotel is a project of EMROC Emirate-Moroccan General Trading & Investment Company. The combined enabling project is executed under the combined management of JACOBS International Holdings Inc. and NASSAR Engineering Services.The project is located to the south-east of Emirates Palace and west of Etihad towers, at about 20m away from the sea shore. Since the two projects are located next to each other a combined shoring system was constructed for the entire area. This decision was based on an agreement with clients and consultants of the two projects and resulted in significant savings for both parties. The shoring system consisted mainly of diaphragm wall with ground anchors and steel struts. Cantilever secant piles were used on the eastern side of the plot, adjacent to Etihad Towers` basement.PURPOSE AND SCOPE OF WORKNSCC International Ltd. was responsible for the design, procurement and construction of strutted and anchored diaphragm walls and cantilever secant piles. The shoring layout and a summary of shoring sections are shown below."

Jan 1, 2017

By Randy R. Williams, Brian W. Wilson, George M. Filz, Marina S. W. Li

"Detailed design of an extensive deep mixing (DM) scheme using the Cutter Soil Mixing (CSM) technique was completed for foundation support of mechanically stabilized earth (MSE) walls for Kitimat Liquefied Natural Gas (LNG) at Bish Cove, British Columbia, Canada. The design was based on the provision of soil-cement structures, constructed in highly variable subsurface conditions that consisted of thick deposits of fine-grained soils overlying granular soils, and required to meet project-specific performance criteria, to support the MSE walls. The design, consisting of rectangular CSM panels constructed to form barrettes connecting to a longitudinal wall of continuous CSM panels, was configured to manage the distribution of stresses and strains that could be developed within the soil-cement structure.The results from 2D finite element analyses were used to determine the necessary arrangement and properties of the CSM panels to accommodate localized areas of relatively high shear, tensile and compressive stresses within the soil-cement structure. The relationships between unconfined compressive strength and elastic modulus for fine-grained and granular soil-cement structures obtained from the Bish Cove data were compared with published references and were found to be significantly different in the higher strength range materials.BACKGROUNDDeep Mixing design was completed for the development of the Kitimat LNG Facility located in Bish Cove, British Columbia, for support of two relatively high MSE walls and associated bulk earthwork operations. Deep mixing was necessary to treat the very weak native deposits in-situ to meet project performance requirements and physical constraints without the need for significant excavation and disposal work. The DM design was undertaken on the basis of adoption of the CSM technique for in-situ ground improvement of the native foundation soils which consisted of very soft to soft fine-grained marine deposits and loose to compact sandy silt to silty sand, overlying dense sand and gravel (Fig. 1). The DM area is located immediately upslope of the Bish Cove beach area, and is “L” shaped in plan, approximately 300 m long by approximately 28.8 m wide (parallel to the beach area) and 165 m long by an average width of 21.0 m (perpendicular to the beach area). The depth of the DM ranged from about 5.0 m to 30.7 m with typically 2.0 m embedment into dense granular soils. Details of the design philosophy, including an overview of the DM design and the project background information are presented by Li et al. (2014a). Details of the construction aspects of the Kitimat LNG deep mixing are presented by Wilson et al. (2014)."

Jan 1, 2015

By Scott A. Walker, Gabriel J. Alcantar, Brian Zuckerman, Ramin Golesorkhi

"The stadium development consists of construction of a 68,500-seat, open-air NFL football stadium for the San Francisco 49ers. The main structure will consist of a 7-story above grade steel structure supported by over 3,000 piles. Berkel and Company Contractors, Inc. (Berkel) was selected as the design-build pile contractor who used their auger pressure grouted displacement (APGD) piles for this project. During an indicator pile installation and pile load test program, fifteen piles were tested to develop installation criteria to support demands of 150kips tension and 180 kips compression. Following the indicator pile program Berkel installed 3088 piles in 30 working days. Throughout pile installation data were collected with an automated data acquisition system (DAS). During pile installation field engineers from Treadwell & Rollo observed the pile installation as well as the real-time data from the DAS. Strategic staging and pre-production planning by Berkel along with consistent collaboration with the design team created an atmosphere for a successful and on schedule project completion.IntroductionThe new San Francisco 49ers Stadium in Santa Clara, California will be a 68,500-seat facility, a rendering of which is shown in Figure 1. The main structure will consist of a 7-story above grade steel structure supported by more than 3,000 piles. The north, east and south portions of the stadium are designed as an open seating bowl, while the western portion includes open seating at the lower levels and seven-story tower which houses over 150 suites.The stadium project includes the stadium structure, as well as elevated open pedestrian walkways, commercial community space, and three new pedestrian bridges spanning a nearby by creek. Sustainable designs and innovations such as a green roof, photovoltaic panels, a ground source geothermal system, stadium-wide Wi-Fi capability, and access to public transit are provided throughout the project. The stadium is designed as an open, light, and airy structure and is surrounded by an existing amusement park, office buildings, the Santa Clara Convention Center, and the training facility of the 49ers."

Jan 1, 2015

By Matt Fenwick, Douglas R. Schwarm

Stringent underwater noise limits at the Fairview Ave. N. bridge replacement on Seattle's Lake Union required an innovative approach to supporting the 470-ft long drill trestle. Screw-in foundations would reliably mitigate noise, but the required 500-kip bearing resistance were an order of magnitude higher than typical helical piles. This paper describes the process of designing, installing, monitoring, and testing 22-inch dia. helical piles 80 feet long with 36- and 42-inch dia. helices. A static load test confirmed that the conventional k-factor design method can be extended to capacities of up to 800 kips. A 375 ft-kip drive mechanism had to be fabricated because no North American equipment could supply the necessary installation torque. Real time installation monitoring and later "re-torque" tests confirm that helical piles gain capacity with time, analogous to driven piles under restrike. Underwater and on-land measurements confirmed very low noise, suggesting the possibility of widespread adoption where similar limits are imposed. Overall, this case history illuminates the need for innovative deep foundation types in response to ever-increasing regulatory constraints.

Sep 8, 2021

By Suthan Pooranampillai

Verification of drilled shaft resistance is primarily obtained through the use of different load testing methods. Procedures utilized include conventional top down static loading, the Osterberg load cell (O-cell) test and dynamic tests such as the Statnamic method. The O-cell test provides a means of obtaining separately the base and side shear resistance behavior of drilled shafts (cast-in-drilled-hole). Alternatively, the Statnamic load test method enables the engineer to derive base and side shear behavior separately, based on measurements of load, accelerations and strains along the length of the shaft. However, due to time and cost constraints these tests can only be performed on selected shafts within a project. Post grouting of a drilled shaft base embedded within a cohesionless material, with a low mobility compaction grout, will essentially pre-load the shaft base soil against the side shear and self-weight in much the same manner as an O-cell load test (when the load cell is placed within the base vicinity). Therefore, successful post grouting of a drilled shaft would enable verification of both shaft side shear and base resistance simultaneously on each and every shaft it is carried out on. Additionally, such post grouted shafts display stiffer load-displacement response during subsequent downward, superstructure induced, loading compared to ungrouted shafts. Verification of resistance on each and every shaft through the use of post grouting will allow an increase in resistance factors (reduction in safety factor) used in the design. Two 6 ft. diameter drilled shafts were constructed in Fredonia, WA, for WSDOT, each with an approximate length of 52 ft. The shafts were terminated within medium dense poorly graded silty sand. Statnamic load testing of the shafts indicated maximum derived static side shear and base resistances of 2545 kips and 507 kips (1.6 in. displacement) for shaft One and 2466 kips and 212 kips (1.4 in. displacement) for shaft Two. Shaft Two was subsequently grouted, with a low mobility compaction grout. Shaft base mounted total earth pressure cells measured a maximum sustained pressure of 55.44 ksf during the compaction grouting operation. Shaft displacement reached 0.65 inches in the upward direction at termination of grouting. Comparison of grouting data with initial load test information indicates that properly instrumented post grouting verifies shaft base and side shear resistance. In addition, these grouting induced resistances were much higher than design values supplied by the engineer using conventional resistance factor design. Large scale laboratory testing also shows that base grouting verifies higher soil resistances than permissible in conventional design.

Jan 1, 2010

By Jesús E. Gómez

Verification and production testing of soil nails requires debonding the upper section of the soil nail to isolate the portion of the soil nail intended for testing within a specific ground type. In pre-drilled soil nails, debonding can be accomplished relatively easily because the bar can be fitted with a debonding sheath before its installation. However, debonding of hollow core bar soil nails requires special procedures to achieve the intended result. This paper is a summary of the Federal Highway Administration (FHWA) Hollow Bar Soil Nail (HBSN) Test Program, which is described in detail in FHWA-CFL/TD-10-001. The program was developed to establish a suitable debonding procedure to test hollow core bars in soil nailing applications, and to initiate a database on typical bond values of HBSNs. The investigation showed that it is possible to debond hollow core bars for testing. It was also found that hollow core bars installed in granular soils may present ultimate bond values that are significantly higher than those typically used for design of conventional pre-drilled soil nails.

Jan 1, 2011

By Dale Berner, Michael O’Sullivan

"This paper focuses on lessons learned from the innovative designs, in-the-wet construction methodology and modified foundation conditions, for two United States Army Corps of Engineers, USACE, Megaprojects:(a) The over $2 Billion Olmsted Dam across the Ohio River for the Louisville District; and(b) The $1.75 Billion Inner Harbor Navigation Canal, IHNC, Lake Borgne Hurricane Barrier in New Orleans for the Hurricane Protection Office, and the New Orleans District.Design innovations for the 24-inch dia. pipe pile foundation for the Olmsted Dam project include: (i) the use of controlled-fixity moment connections to the dam monoliths in order to tune the response of the dam under the 8.3 Richter scale seismic Maximum Credible Event, MCE; (ii) soil densification to inhibit liquefaction potential and (iii) design to facilitate underwater construction in a river with a highly moveable sand bed.Design innovations for 66-inch dia. concrete cylinder piles for the IHNC floodwall include: (i) the use of soil structure interaction, SSI, analyses to verify capacity to resist deep-seated failure plane in soft soil, while limiting lateral deflections to acceptable limits; (ii) the use of geo-fabric and scour stone for enhanced foundation response and (iii) design for ""in-the-wet"" construction on a fast-track basis.LESSONS LEARNED FROM THE INNOVATIVE OLMSTED DAM FOUNDATIONThe over $2Billion Olmsted Dam on the Ohio River is currently under construction 16 miles upstream from the confluence with the Mississippi River. It will consist of an 800-foot-long tainter gate section, a 1,400-foot navigable pass, two boat abutment sections, a fixed weir section, and upstream and downstream scour protection. The Olmsted Dam and its two, 1,200-foot locks, which were built in 2002, will eventually replace both Locks and Dam #52 and #53, both built in 1929, and thereby bring significant benefits to the Ohio River navigation system.In 2002, the Jacobs/COWI JV completed the design of the dam; which was an engineering challenge for several reasons, including:(a) Its proximity to the New Madrid Fault, could impose an 8.4 Richter Scale seismic event on the structure, which is located in an area of potentially liquefiable alluvium. The extensive seismic analysis performed by COWI included a response spectra analyses; lateral pushover analyses of pile foundations; hydrodynamic added masses; pile group effects; and the development of kinematic motions as a result of the soil-pile-structure interaction.(b) Maintaining vessel traffic along the river and accommodating fluctuating river elevations between 30-40 ft annually, and as much as 60 ft in a 100-year period.(c) Designing for the scour and uplift forces of artesian ground water and preserving a wildlife sanctuary on the Southern shore at the dam site."

Jan 1, 2017

By Timothy C. Siegel

This report presents the results of a synthesis on the design and analysis of ground improvement for liquefaction mitigation. The synthesis included an industry survey concerning the practice of ground improvement for liquefaction mitigation. Participation in the survey was solicited by advertisements in several trade magazines and by e-mail for the DFI membership. The survey participants numbered 150. Their professional roles include consulting engineers, specialty contractors, design engineers, government engineers, and academicians. They represent a variety of geographical areas including North/Central/South America, United Kingdom, Middle East, Caribbean, Hawaii, Japan, India, Egypt, France, Australia and New Zealand. Upon completion of the survey, several professionals in the field of liquefaction and ground improvement were interviewed for them to elaborate on the survey results. The interviews are included in the Appendix of this report. Financial support for the project was provided by DFI and Dan Brown and Associates PC. The concept of the liquefaction mitigation synthesis was developed by DFI?s Ground Improvement Committee in recognition that: (a) The results of recent research and post-earthquake reconnaissance have challenged previously longheld beliefs about liquefaction and associated mitigation techniques, and; (b) The DFI membership and the engineering/construction industry are interested to know if and how engineers and designers are subsequently adjusting their practice in consideration of recent research and post-earthquake reconnaissance. For more detailed information on recent research and post-earthquake reconnaissance, presentations are available from the State-of-the-Art Forum: Liquefaction Consequences and Mitigation that was held in St. Louis in 2012. A commentary of the state-of-practice in ground improvement for liquefaction mitigation (prepared by DFI?s Ground Improvement Committee) is included in this issue of the DFI Journal. The author would like to thank the participants of the survey and especially Mr. Mike Jeffries, Dr. Les Youd, and Dr. Ikuo Towhata for their willingness to share their expertise in interviews. The author also acknowledges Mary Ellen Bruce of DFI, Billy Camp of S&ME, Inc., and Marty Taube of DGI Menard (and Chair of DFI?s Ground Improvement Committee) for their signifi cant contributions.

Aug 1, 2013

By Reda Mikhail, M. Birkan Bayrak

The Washington State Department of Transportation (WSDOT) State Route (SR) 167/70th Avenue East Vicinity Bridge Replacement Design-Build project is located in Fife, Washington. This $40 million project consists of replacing the existing 70th Avenue Bridge over Interstate 5 (I-5) with a single-span bridge of about 220 feet long with approach embankments. The subsurface conditions along the new bridge alignment generally consists of alluvial deposits with high potential of liquefaction overlying glacially overridden deposits. In the early stages of the project, drilled shafts were considered as the deep foundation system; however, after an additional subsurface investigation is completed at the site, driven pipe piles were selected as the deep foundation system. Bridge abutments are supported by 24-inch diameter, 80-foot-long open-end driven steel pipe piles. The pile length was determined to bypass a relatively thick liquefiable zone and to tip the piles above what could be compressible soils. The use of advanced seismic analysis was instrumental in optimizing the pile length. The dynamic testing performed on numerous piles indicated what could be unique soil setup factors compared to those measured in local projects as well as those reported in national design manuals. Detailed discussions of the pile foundations design and construction is presented in this paper.

Sep 8, 2021

By Rajasekar Subbian, Jessica Oudhof

In the Netherlands pile foundation design is done using CPTs in accordance with EC7 national annexure. The capacity per tip level is calculated for every CPT followed by zonation to find the tip level per zone. The correlation factors are used to take into account the variability in ground across the zone and they depend upon the number CPTs within the zone. The CPTs and pile tip levels selection for zoning is an iterative process that can demand significant manual effort to produce an economical pile plan. This often leads to the use of conservative correlation factors in order to accelerate the design process. Thus, it has been automated in a tool with CPTs, pile location and loads, and capacities as input. The tool has also been employed in two case studies and the results are compared to the current design practise.

May 1, 2022

By Harald Vogel, Johannes Lachenski, Friedemann Koetzel, Sebastian Schnell

In this paper, a digital subsoil approach, a work-in-progress, will be presented describing the transformation from a classical 2D to digital 3D thinking process in the design of geotechnical structures. Certain pitfalls as well as lessons learned are described, and the reader can understand that the digitalization process of the design of geotechnical structures is always a problem-focused approach by creating systems for certain processes rather than setting rules or regulations. Three project examples are presented. Two of the presented project examples feature a heterogeneous geology distribution and made it necessary for the design of the foundations to work with 3D subsoil and 3D calculation models. However, the digital 3D design process in the third project, an inner-city excavation pit, is driven by the complicated boundary conditions making it necessary to work in a parametric 3D design space. All projects have in common, that new processes had to be developed. The paper concludes with a flow chart describing the process of the elaborated digital subsoil approach.

May 1, 2022

By Charles M. Wilk, Lori Tiefenthaler

"Information presented in this paper can be used to support deep soil mixing, subsurface grouting and slurry wall technology as sustainable construction technologies. Ordinary Portland Cement (OPC) is the default cementitious material used by Deep Foundation Institute (DFI) Members for geotechnical work. Owners, engineers and contractors can contribute to the sustainability of a geotechnical project by increasing the use blended hydraulic cements and industrial byproducts to replace some of the OPC in mix designs. Sustainability is defined as the quality of not being harmful to the environment or depleting natural resources. Production of cementitious materials consumes natural raw materials and energy while also generating air emissions and waste. Life Cycle Assessments can be used to compare the relative environmental impacts of one cementitious material to another. Blended hydraulic cements (BHCs) are interground (or blended) mixtures of Supplementary Cementitious Materials (SCMs) with OPC. Commonly used SCMs include fly ash, ground granulated blast furnace slag (GGBFS) and limestone. Examples of industrial byproducts commonly used in geotechnical work include coal combustion residuals (CCR) (aka fly ash), and ground granulated blast furnace slag (GGBFS). Much of life cycle impact of these SCMs and industrial byproducts have already been borne by the industries that generated them. There is increasing awareness to LCA and sustainability of different materials used on projects. This is evident in the application of the Leadership in Energy and Environmental Design (LEED) program. The savings in environmental impact with the use of SCMs and industrial byproducts can make proposed use of these materials in a geotechnical project more attractive in terms of sustainability. This paper presents (a) information that compares published life cycle assessment data of OPC, BHCs, and slag cement (SC) to illustrate the potential benefits to sustainability and (b) general strategies for positioning a geotechnical application, use, project design or cementitious material mix as a more sustainable alternative"

Jan 1, 2017

By Jason Buenker, Molly Winston

Torque-installed piles are gaining popularity in Southern California as the go-to deep foundation element for small- to medium-capacity loads in urban environments. The torque-installed pile is a displacement- based screwed pipe pile with a closed-end conical tip welded to the bottom of the pipe. Torque-installed piles are most efficient in loose to medium dense soils with high liquefaction potential. Where used properly, torque-installed piles can be installed faster, require less clean-up, and create less onsite vibration/disturbance than other pile alternatives. However, torque-installed piles are not applicable in all soil conditions and care must be used to apply the pile effectively in the correct subsurface environment. This paper will review current Southern California state-of-the-practice for torque-installed pile design and construction, potential roadblocks to successful installation, and available capacities from load tests. INTRODUCTION Torque-installed piles are a type of full-displacement screwed pipe pile originally developed in Southern California circa 2001 by Substructure Support, Inc. The pile is unique for its proprietary closed-end conical tip shown in Fig. 1. The tip has a welded steel-helix plate and cutter teeth that allow the pile to be advanced efficiently under applied torque and down pressure (crowd). Since original development of the pile, several contractors or manufacturers have proposed similar proprietary screw-type piles with comparable conical tips. Pile installation is relatively quiet, vibration-free, does not generate spoils, and faster than comparable pile types. The pile was originally developed as an alternative to driven pile foundations and remains a critical substitute to driven foundations in urban environments. Torque-installed piles are conventionally specified as 12 ¾-inch outside diameter (OD) steel pipes with a ⅜-inch-thick wall, although larger sizes with alternative dimensions have been used outside Southern California. Pile installation lengths generally range from 30 to 50 feet but may reach 80 feet or greater where soil conditions permit. The pile is generally backfilled with concrete following installation to increase lateral pile stiffness and may incorporate rebar cages or other reinforcing steel to facilitate connections to structural elements. The pile is frequently specified using performance-based specifications that encourage contractor innovation and use of proprietary installation means and methods.

Jan 1, 2019

By Shields H. Arup

The paper describes the innovative foundation reuse and strengthening works for two buildings in Central London. A 1950s building on piled foundations (65 Whitfield St) and a 1930s building (67-69 Whitfield St) on 3m deep pad foundations were both extended upwards by two new stories. The Client for the project is Derwent London, with Make as their architect, Main Contractor Multiplex and Engineer Arup. Little was known about the foundations of either building at the start of the scheme. Extensive investigations of the existing foundations and ground conditions were carried out in both buildings. At 65 Whitfield St, investigations identified piled foundations, but found that pile lengths were short and variable. As a result, strengthening works solutions were adopted whereby the increase in column load was shed into new mini piles constructed around the existing pile caps. At 67-69 Whitfield St, deep pits were used to investigate the foundations and reuse was justified based on understanding of the pad dimensions, concrete strength, and strength and stiffness of the underlying geology. For both buildings the residual risk was closed out through monitoring during construction. The combined reuse of the structural frame and foundations of both buildings facilitated a sustainable solution, breathing a new lease of life into outdated buildings.

May 1, 2022

By Ambarish Ghosh, Rituparna Dey, Indrajit Chowdhury

"In port and harbor facilities, jetties and cargo berth terminals are usually installed on piles that remain partially embedded in soil, while a part of it behaves as columns supporting top deck. Technology in vogue adapts a pseudo static analysis in computer where the top deck including piles are analyzed as an integrated system based on finite element method when the piles are modeled as beam elements, while the soil in which it is embedded is modeled as linear or nonlinear springs. Typical berthing force of the ship is considered as a pseudo static force where the dynamic characteristics of the force is taken into consideration by an equivalent impact factor and little study exists on the actual behavior of these type of piles under the transient shock due to berthing impact. Present paper proposes an analytical solution based on which one can compute the dynamic response of such jetty piles considering shear modulus of soil constant with depth. Considering the solution is analytical in nature no special software is needed and can well be adapted fordesign office practice using generic utility software like MATHCAD, MATLAB etc. that makes theproposed model computationally very efficient.INTRODUCTIONResponse of piles under dynamic load has been an important study in the realms of civil engineering, where significant research has been carried out on its dynamic behavior under harmonic loads like one experienced in a machine foundation or under seismic force.A number of researchers have given solution to this problem like Parmelee et al (1964), Tajimi (1966), Penzien (1970), Novak et al (1974, 1983), Banerjee and Sen (1987), Dobry and Gazetas (1988),Chowdhury and Dasgupta (2008).However, most of these theories are based on piles loaded under harmonic load and valid for long piles where structural failure precedes the soil failure considering the piles are long and flexible."

Jan 1, 2015