Search Documents

Jan 1, 1994

By Gerald Verbeek, Erick Baziw

Downhole Seismic Testing (DST) is a very popular applied seismology site characterizing tool within geotechnical engineering. A challenging aspect of DST is to characterize the acquired seismic data sets to determine the analysis method that will result in the most accurate interval velocity values. BCE has invested considerable resources into developing Seismic Trace Characterization (STC), which uses various independent parameters of the acquired data at a particular depth. Initial work in this area resulted in the selection of the linearity estimate from the polarization analysis, the cross correlation coefficient of the full waveforms at the particular depth and the preceding depth and a uniquely developed parameter referred to as the signal shape parameter for this characterization. Subsequent analysis in STC identified two other parameters: the Signal-Noise-Ratio (SNR) and the Peak Symmetry Differential (PSD). The paper briefly describes these parameters and then outlines how they can guide the data analysis to derive more accurate results, especially near surface, which is especially important to assess the liquefaction potential in areas prone to earthquakes, such as California. The process will be illustrated with actual data from another area prone to earthquakes, namely New Zealand. 1. INTRODUCTION The near surface characterization of low strain in-situ shear wave velocities (VS) has proven critical for liquefaction assessment. Liquefaction is a phenomenon in which dynamic loading of saturated soil results in the material properties to change suddenly from a solid state to a liquefied state. VS is an important parameter for evaluating liquefaction potential due to fact that it is influenced by many of the variables that influence liquefaction (e.g., void ratio, soil density, confining stress, stress history, and geologic age (Andrus et al., 1997)). Aki and Richards (2002) also outline that the amplitude of ground motion should depend on the density and shear wave velocity of near surface soils and rocks according to the theory of wave propagation. Since the change in density with the increase in depth is relative minor compared to that of the shear wave velocity, the latter is a very useful parameter to represent site conditions (Stewart et al., 1997). Bray (2014) and his colleagues carried out an extensive geotechnical analysis of the catastrophic liquefaction that occurred in Christchurch, New Zealand in 2010 and 2011 and found that near surface rather than deep liquefaction resulted in extensive foundation damage.

Jan 1, 2018

By Paul Doherty

Expansion of the global piling industry has been coupled with significant research efforts investigating the mechanisms controlling pile capacity. Static pile design has transitioned from total stress approaches toward effective stress design, with associated improvements in predicting pile performance. As a result, the available literature is heavily skewed toward static capacity prediction. However, when considering piles offshore, the majority of loading is not static but highly variable and cyclic in nature. This paper outlines the additional factors that require consideration for cyclic pile design, including elevated loading rates, cyclic displacements and capacity degradation. A review of the literature identified a number of cyclic pile testing programs which are collated in this paper. General trends are established through comparison of the tests within the database and the conditions where cyclic loading is most likely to be a concern are identified. In particular, loading conditions which involve full plastic shear reversals are seen to cause the most extreme cyclic damage, with the degraded capacity as low as 31% of the precyclic static capacity. The underlying mechanisms which can result in cyclic damage are explored, with particular attention given to the pore pressure response, radial stresses, shear transfer and particle reorientation.

Jan 1, 2009

By Z. Q. Zhou

It is the first worke in design of pile foundation to determine the carring capacity of single pile, and a static loading on site is considered to be the lost derect and reliable way. All values P and settlements S induced can be plotted as a broken-line. Since soil is a kind of elasto-plastic and cohesive material, the increasing of settlements is generally greater than that of loads. Different value Pu nay be given by different tester on his P-S diagram, because of erroys in the test and complicated, characteristics of soil. The analytical method of exponential equation shown in this paper derives a specified solution. After using an exponential curve to regress values of loads P and corresponding settlements S from on-site test, coeficients A and B of exponential equation can be obtained. With this curve an ultimate carrying capacity of single pile can be determined. The resistant forces of pile shaft and pile tip can also be defined by the tangent of the calculated knee point, as it is called (tangent method). At last, an example is given to show how the ultimate carrying capacity of f 500mm bored pile is obtained with this method for a project in Kunming.

Jan 1, 2010

By Roy A. Imbsen

Following the 1989 Loma Prieta earthquake, California Department of Transportation (Caltrans) expedited an effort to evaluate and retrofit important state-owned toll bridges to en­hance performance of the state's transportation systems during and after major (credible) earthquake events. Imbsen and Associates, Inc. (IAI) along with their sub-consultants, were awarded a contract to conduct seismic evaluation and to develop retrofit design for Benicia-Martinez Toll structure, to meet a "Serviceable" performance requirement after the event of a "Safety Evaluation Earthquake." This paper describes the design and construction specifications for the deep foundations supporting the main spans of the Benicia-Martinez Bridge. Benicia-Martinez Toll Structure (George Miller Bridge), a high-level deck-type welded truss bridge with welded girder approach spans, carries Interstate Route I-680 over the easterly end of Carquinez Strait near San Francisco, CA. The nearly 5000 ft long main truss structure consists of ten spans, ranging from 330' to 528' in length, supported on cellular reinforced con­crete pier structures. Foundation systems across the waterway, consist of cellular reinforced concrete footings, supported by groups of 6' diameter, concrete filled, steel caissons, resting on 5' deep rock sockets, at depths of 50' to 150' below the water level. Seismic evaluation of the existing foundation systems accounted for spatially varying ground motion along the length of the structure, variability of foundation material strength (i.e. at bed-rock), variation and effects of scour depth on the performance of the foundations, and dy­namic soil-structure interaction. Performance of caissons beyond their elastic strength, as well as their effects on the behavior of the foundations and substructures were evaluated and considered in establishing foundation vulnerabilities. Several retrofit strategies were considered leading to a final retrofit strategy to strengthen end connections of existing caissons, as well addition of new caissons to provide adequate lateral force resistance for the foundations. Final design package includes specifications as well as construction methods and requirements for existing and new caissons, under traffic, and pile load testing procedures for design loads of up to 12500 kips per caisson.

Jan 1, 1998

By Basem Sh. Hazzan

In the last four decades significant effort has been devoted to designing piles in expansive clay soils. Nevertheless, only a scant effort has been devoted to the elimination of heave forces acting on the upper part of lightly loaded piles. For this purpose, an investigation site was established in Karmiel in Northern Israel. On this site sixteen unloaded cast-in-situ piles, both uncoated and coated, were installed in a moderately expansive clay soil in the end of summer 1996. The piles were executed to different depths ranging between 2m and 7m and were observed over a period of 27 months. Another nine unloaded cast-in-situ bored piles were installed at the end of summer 1998 for carrying out pullout tests. These piles were embedded two meters from the ground surface. Results obtained from observations and from full-scale static pull out tests showed that separating the piles from the surrounding clay in the active zone by a twin walled sleeve eliminated the heave forces significantly. The scope of the work is, determining of the elimination degree of the heave forces due to the provision of the above sleeve.

Jan 1, 1999

By H. Meseck

Dynamic pile test methods to establish the bearing capacity of driven piles were developed in the USA more than 20 years ago. In the Federal Republic of Germany, the first dynamic pile tests were carried out at the end of the 70's. Today dynamic pile tests are successfully used to establish the integrity and bearing capacity of driven and bored piles. The Institute of Foundation Engineering and Soil Mechanics at the Technical University of Braunschweig has developed its own method of measuring and evaluation for the execution of dynamic pile tests. The principles of the dynamic pile tests, the measuring and evaluation plant as well as the experience gained with it in the examination of cast-in-place piles are presented in this contribution.

Jan 1, 2010

By Franklin M. Grynkewicz

As part of the Boston Harbor clean up project, the new 1,000 mgd Deer Island Sewerage treatment plant includes ten 240 feet high egg-shaped "residuals" tanks. Contract documents called for these structures to be supported on 2,600 sixteen inch concrete filled pipe piles. The project site is underlain by highly variable glacial and marine deposits. Subsurface conditions vary from one extreme where firm glacial deposits exist at subgrade to the other extreme where 70 feet of medium stiff clays overlying weathered bedrock must be dealt with. The most common profile consisted of 15-20 feet of sands, 20-40 feet of marine clays, and 20-60 feet of stratified glacial deposits (commonly called tills) overlying Argillitic bedrock. Post bid redesign work, initiated as a cooperative effort between the owner and the general contractor, demonstrated that an $8 million savings could be realized if high capacity 48 inch diameter caissons replaced the specified pipe piles. A highly unusual arrangement of having the general contractor and specialty subcontractor providing input to the owner's engineering team allowed the redesign work to proceed on a "fast-track" schedule.

Jan 1, 1992

By James J. Cahill

Contractor's working in an urban environment face a multitude of working conditions. There is no typical "Downtown" job site. From afar we just see the skyline, or up close a specific building. This, of course, does not give us a clue as to the site conditions the foundation contractor faced in doing his work. The open, downtown building site is still available on some projects, but they are becoming rare as our cities are becoming more developed. A typical site today might include any one or several of the following problems: A. Deep pit with no ramp access B. Multi-type known or unknown obstructions C. Height limitations D. Load restrictions E. Existing adjacent building founded on shallow foundation F. Existing foundations G. Existing tunnels, utilities or subways

Jan 1, 1991

By Gang Guo, Zhong Liu, Yi Zhang, Jingchun Lu

"Abstract Application of soil displacement screw pile (known as SDS pile) has been experiencing accelerated growth in Chinese deep foundation industry because of its technical advantages, environmental benefits, and cost effective as well. As bored displacement piling, SDS piles are able to perform better than non-displacement piling such as CFA plies due to changing the stress state in the soil around SDS piles during the installation. Therefore the design methods between the conventional pile type and SDS pile type have some differences. Based on the methodology research, current Chinese piling rigs, displacement augers and piling projects are introduced, and the current design approaches for SDS piles in China are also described. Moreover, the design results are verified by using full scale load tests, and a part of the research results of SDS piling system acquired in China are presented.IntroductionThe Continuous Flight Auger Pile, also known as the CFA pile, has occupied about 22% in the pile market all over the world (Van Impe, 2004; Bottiau, 2006). The CFA piles are usually used for large diameter (600mm~1200mm) pile foundations and deep excavation projects. Whereas the small size CFA piles (400mm~500mm) are mainly applied for composite foundations in China. In the past 10 years, the new technology of soil displacement screw piling has been applied worldwide (Prezzi et al., 2005). And it is also extensively used for high-rise buildings, industrial plants and railway projects in China (shown in Figure 1)."

Jan 1, 2014

By Ivan Jackson Madura

The new Paradisus Coco Beach Resort in Rio Grande (PR) is located on an old swamp area, which has been filled with relatively clean to silty sands. The swampy deposits consists of organic silts, peat and loose fine to medium sand and silty sand. The project requires the placement of 1.0 to 1.5 meters of additional fill together with the construction of light structures. The need for the fill will trigger the development of settlements in the underlaying weak and compressible stratum. Furthermore, the susceptibility of the loose sand to liquefaction during an earthquake was considered. This paper describes the soil improvement by means of vibro-replacement, the purpose of which was threefold: reduction in total and differential settlement, acceleration of settlements during the surcharge period and densification of the loose sand to reduce its liquefaction potential. The predesign is presented together with relevant construction details of the preliminary trial areas from which the final column diameter and grid spacing were derived. Instrumentation together with settlement observations during the surcharge period are presented as well and compared with the initial predictions.

Jan 1, 2002

By Peter J. Nicholson

Since the reintroduction of soil mixing to the United States over 10 years ago, the work installed by soil mixing technology has grown dramatically. From an annual turnover of less than ten million dollars per year the volume of soil mixing put in place has grown to an estimated $40 million per year in the year 2000. The majority of work done to date has involved walls, either for excavation support, permanent retaining structures or hydraulic cut-off walls. The other major use for soil mixing has been for mass stabilization of soils whether for isolation of contaminants or for retaining structures. This paper will discuss the uses of and costs of typical soil mix structures. BACKGROUND Soil mixing is defined as the in-situ combining of reagents, typically cement, with native soils, the purpose being to modify or improve the ground. This history of soil mixing covers only the use of cement slurry, aggregated with soil in-situ by mechanical mixing methods only. Soil mixing by use of high-pressure hydraulic means, also known as Jet Grouting, will not be discussed. In addition this will not cover ex-situ (above ground) mixing, or mixing dry reagents with soil. Only mixing applications for building, civil and heavy construction applications will be discussed, with only passing reference made to uses of soil mixing for environmental remediation work.

Jan 1, 2001

By Charles Pol Vuillier

Piling work for modification to the Charles Grimes Bridge in Melbourne, Australia required piles to be installed through 15 to 20 m thickness of very soft to soft silty clay overlying 10 m of stiff clays and sands in turn overlying siltstone. The presence of an old sewer founded at depth in the soft clays demanded that vibrations be kept to a minimum. Two pile type were used by Vibro-pile (Australia) to provide the client with the most economical piling price. The two pile types were CFA piles of 750mm diameter founded in the weathered rock and a full displacement concrete injected screw pile developed by Vibro-pile called the "Z" pile, founded on the rock. The development and features of the "Z" pile are briefly discussed, including the perceived applications and advantages of the pile type. On board instrumentation comprising a computer was used to monitor all aspects of the construction. The rig instrumentation provided an important quality control measure that gave confidence in the pile installed. Pile performance was proved on the cast in situ piles by dynamic load testing methods. Initially tests performed with a 120 kN drop hammer, which was not capable of mobilising the required loads. The performance was then satisfactorily proved by using a drop hammer of 20 tonne mass delivering blows drop heights of 1.5m. Low strain integrity tests on a number of piles were also used to confirm the structural integrity of the piles.

Jan 1, 2000

By Don Deardorff, Ke Yang, Yingcai Han, Ken Sorensen, Robert Kruger, Mark Petersen, Diane Fiorelli, Larry Goldfarb, Kathryn Petek, Kwabena Ofori-Awuah

Design of deep foundations for lateral loads requires an understanding of soil-foundation-structure response during loading. Lateral loads on a deep foundation (piles) could be due to earthquakes, winds, waves, and/or machine vibrations. Over the years, analysis of response of piles due to lateral loads evolved from closed-form solutions to p-y methods to strain wedge to finite element/finite difference modeling. Although analysis of lateral response of piles and shafts is routinely performed, there is no single guidance document and/or standard for design and testing. Several different analytical methods are available for the analysis, and the resulting design can result in significantly different responses which can create confusion. This is especially true for analyzing and designing piles in potentially liquefiable soils with lateral spread issues under seismic conditions.This guidance document is intended to assist geotechnical engineers, pile designers, and contractors in analysis, design, and testing of piles and drilled shafts for lateral loads. This document discusses the background of different analytical and testing procedures and presents the recommended methods for analysis, design and testing of piles for lateral loads.Chapter 1 defines the different kinds of lateral loads to which a single pile or pile group may be subjected. This first chapter also presents different types of piles used to resist lateral loads.Chapter 2 discusses geotechnical issues related to lateral pile design such as liquefaction and lateral spreading and other non-seismic issues. Also addressed in Chapter 2 is geotechnical site characterization (as related to lateral loads) in terms of site investigation, in-situ testing, geophysical testing, laboratory testing, and estimation of soil/rock properties.Chapter 3 discusses the background and available analytical methods and tools for the analysis and design of single piles and drilled shafts. Several methods of analyses from closed-form elastic solutions to the finite element/finite difference solutions and their applicability are discussed. Available commercial computer software packages for analyzing single piles and drilled shafts are also presented.Chapter 4 expands the discussion of single piles and drilled shafts into the analysis and design of pile groups. In addition, group effects, resistance of pile caps, results of previous experimental and analytical studies, and available analysis tools and software for pile groups are discussed.Chapter 5 presents the issue of lateral resistance of piles and drilled shafts as discussed in different national and international building and non-building codes. A summary of extensive research on several codes are presented to facilitate the compliance with different codes.Chapter 6 discusses structural design issues of individual piles and drilled shafts such as depth of fixity.Chapter 7 discusses soil structure interaction issues related to kinematic and inertial effects due to seismic loading and available methods of analyses.Chapter 8 discusses and presents the typical procedures for the lateral load testing of piles. This guideline was developed as an aid to the practicing engineer in providing information, direction and commentary on the lateral design of deep foundations. Although all reasonable effort has been made to accurately compile the material and information contained herein, no warranty is made with regard to any such material or information and the Deep Foundation Institute assumes no responsibility for any possible errors or any direct or indirect result of the use of any such material or information. It is not intended that this document address every factor affecting lateral design for every situation. Therefore it is the responsibility of the person utilizing information from this document to confirm that it is appropriate and correct for their situation as well as to understand and properly apply

Jan 1, 2012

By Roy H. Borde

The design of foundations to support overhead signs is primarily based on providing adequate resistance against horizontal wind loads. The typically used subgrade reaction model for the load-deflection analysis of laterally loaded piles and shafts has been found to underpredict the capacity of shafts with length to diameter ratios less than five. The general applicability of an improved model incorporating the influence of shear and moment resistance at the shaft base is demonstrated. The detrimental effect of ground surface slope angle on the ultimate capacity is discussed, and a design chart for estimating the magnitude of the reduction in capacity is presented. A comparison between the predicted and measured responses of nine full-scale load tests performed within this study and sixteen external tests is presented. The models described are implemented in the computer program "LTBASE".

Jan 1, 1988

By Abdul Aziz Hanifah

A novel instrumentation and analysis technique, called GLOSTREXT method has recently been introduced for bored pile load tests in Malaysia. This technique provides an innovative and improved alternative for conventional bored pile instrumentation methods commonly practiced for the past few decades. Results for five case histories involving full scale static load tests for high capacity bored piles with both new and conventional instrumentation details placed in within the same instrumented piles are presented to demonstrate the advantages of this novel technique. Results show good agreement between the new and conventional instrumentation.

Jan 1, 2006

By K. Rainer Massarsch, Bengt H. Fellenius

"Abstract Vibrations generated during the driving of piles or sheet piles can affect buildings or installations in the ground. However, observed building damage is not always caused directly by dynamic effects, but can also be related to foundation conditions. The importance of geotechnical conditions is usually not taken into consideration in most vibration standards. This paper describes how building foundations, and in particular mixed foundation types, are especially sensitive to ground vibrations. A method is presented for assessing the risk of settlement due to vibrations in granular soils. Also, a simple concept is proposed for estimating settlements in the vicinity of driven piles.1. INTRODUCTIONUnder unfavorable conditions, the installation of piles or sheet piles can cause damage to buildings or other structures on the ground. Frequently, such damage is attributed to vibrations of the building itself. In many countries, national or international standards are used to assess the risk of vibration damage to buildings. As such standards are often prepared by engineers with little or no geotechnical knowledge, the effects of ground conditions on vibration propagation and damage to building foundations are generally not recognized, and damage criteria based solely on the dynamic response of buildings neglect the importance of damage mechanisms governed by geotechnical conditions. One potentially important damage mechanism is differential settlement below buildings, especially when these are founded on loose granular soils. When seeking guidance in the literature, little or no information can be found regarding methods to assess permissible levels of ground vibrations with respect to risk for settlement.This paper focuses on building damage that can be attributed to foundation conditions. In the case of ground vibrations due to pile and sheet pile driving, differential settlements are of particular importance as the ground vibrations attenuate relatively rapidly from the source. Consequently, settlement below part of the building, which is located close to the vibration source, can be significantly larger than at a distance further away.Piles are often a cost-effective foundation solution for buildings on loose and compressible soil, frequently located in urbanized areas. Sheet piles are commonly used as support for deep excavations. While impact driving is most commonly used to install piles, vibrators are frequently used for driving (and extraction) of sheet piles. It is important to recognize the fundamental differences between impact and vibratory driving. During impact driving, the pile is subjected to stress waves of short duration. The driving process creates vibrations, which radiate from the shaft and/or the toe of the pile into the soil. The larger the intensity of the stress wave, the larger the dynamic force and the intensity of ground vibrations. In addition to the vibration intensity, which often is expressed in terms of particle velocity, also the vibration frequency is important. When the dominant frequencies of the generated vibrations harmonize with the resonance frequency of buildings or building elements, the risk of building damage increases."

Jan 1, 2014

By Tracy Brettmann, Will Bohlen

An innovative retaining wall design consisting of tangent drilled shafts with supplementary seal piles was used to limit continuing bank erosion along the Brazos River in Southeast Texas. The riverbank erosion had progressed to where it was threatening the stability of both the bridge abutment and corresponding approach embankment of the heavily travelled Highway 99 bridge at this location. A tangent pile design was selected because it was both much faster to install and more cost effective than a secant pile system. The design included both 5.5-ft and 10-ft diameter shafts with depths up to 130-ft and comprised both anchored and cantilevered sections. Supplementary seal shafts were also installed between the structural tangent drilled shafts to help plug any gaps between the tangent shafts. The plumbness and diameter of the shafts were tested using a sonic caliper to make sure the shafts were installed within the specified tolerance. The initial design had to be revised when a record flood from Hurricane Harvey impacted the site during construction. Introduction The Fort Bend Grand Parkway Toll Road Authority (Owner) needed to protect the north bridge abutment with a retaining wall system due to rapidly eroding conditions of the Brazos River banks within the 300- feet-right-of-way of the State Highway 99 Jodie Stavinoha Bridge. The extent of the local scour and erosion along the north bank of the Brazos River has caused concern for the structural integrity of the bridge. The magnitude of the erosion along the north bank at the location of the bridge has been measured at about 120 feet over three recent hydrologic flood events locally referred to as Memorial Day 2015, Memorial Day 2016, and Tax Day 2016. During construction, a new record flood level occurred due to Hurricane Harvey in August of 2017 that resulted in a portion of the retaining wall needing to be redesigned due to even more erosion occurring. The Brazos River is an actively eroding and meandering alluvial river plain that naturally meanders and migrates over time. The processes of bank erosion and meander migration were ongoing before the bridge was constructed and will continue in the future. These recurring major flood events, however, rapidly increased the rate of erosion in just a few years. Background. Due to the need to protect the bridge as soon as possible, the Owner selected a project team consisting of the designer, general contractor and specialty deep foundation contractor prior to final design to work together in developing a cost-effective design that could be implemented rapidly. The project team initially considered both a secant pile and tangent pile retaining wall system using drilled shafts. After reviewing various alternative designs, a tangent pile wall with seal piles was selected based on both cost effectiveness and speed of installation. The tangent pile with seal pile option was approximately 20 percent lower in cost and 50 percent faster to install.

Jan 1, 2018

By Robert W. Schaut

The use of micropiles is increasing for new construction and to retrofit distressed foundations in expansive soils. Typical micropiles in expansive soils have a lower section where the micropile grout is embedded in direct contact with the soil, and an upper section that is cased with rigid PVC pipe or other material to reduce the friction between the micropile and the surrounding expansive soil. In the upper cased section, the micropile grout is in direct contact with the inside of the casing. During construction, grout can flow upward into the annular space between the soil and the outside of the casing as the grout is tremied into the micropile. Thus, various interfaces may exist in a typical micropile, including soil-to-grout, grout-to-PVC, and soil-to-PVC. As the surrounding soil heaves, shear stresses are mobilized along the interfaces. The frictional characteristics of the interfaces are design variables that must be evaluated. For this study, an experimental program was conducted to evaluate the shear strength of the three interfaces listed above. Conventional direct shear testing was performed at a commercial testing laboratory. In addition, specialized testing was performed at Colorado State University (CSU). For the CSU testing, an interface testing protocol was designed using a modified triaxial cell to allow evaluation of the interface characteristics between rigid PVC and cylindrical specimens of grout or clay soil. It is shown that the shear strength of the soil-to-PVC and grout-to-PVC interfaces are similar, both of which are significantly lower than the shear strength of the soil-to-grout interface. This indicates that the use of a PVC casing in the upper portion of a micropile has a positive effect in reducing friction and the shear stresses resulting from expansive soil.

Jan 1, 2011

By Robert Bachus, Jamey B. Rosen

"Abstract Large scale In Situ Barrier Wall Construction projects, specifically those related to earth dams, dikes, and levees, frequently require stringent quality control measures to ensure the success of the wall. This presentation discusses the applications of Geographic Information Systems (GIS) technology to capture information from multiple data streams and provide geotechnical feedback, quality control, and project control feedback. Techniques used to geospatially analyze verticality data from secant piles and panels will be demonstrated. Examples will be presented from barrier wall installations at two sites owned by the U.S. Army Corps of Engineers (USACE): the Wolf Creek Dam in Kentucky, and Center Hill Dam in Tennessee.IntroductionDeep foundation installations require contractors to collect a substantial amount of information over the course of a project, both for internal quality control of construction progress and for demonstrating compliance with customer or owner specifications. Methods of collecting information are constantly improving, bringing with it the need for a systemic approach to managing the increasing amounts and types of data. Handling these diverse types of data presents challenges with both budget and schedule demands. This paper discusses some techniques for adding or increasing quality control in barrier wall constructions by consolidating, visualizing and analyzing data using relational database and Geographic Information Systems (GIS) technology, collectively referred to as Information Management System (IMS) development. The IMS concept is designed to facilitate the collection, transfer and processing of data and provide an easy way to remotely access and visualize construction progress.The remainder of this paper presents the needs and objectives of an IMS applied to quality control in barrier wall construction, the components and data flows involved, the capabilities and user interfaces of the systems and the benefits for the end users. Examples are presented throughout from case study projects including: a pile barrier wall applied in the rehabilitation at the Wolf Creek Dam in Kentucky (under contract to the Treviicos-Soletanche Joint Venture), and a secant pile barrier wall currently under construction in the rehabilitation of the Center Hill Dam in Tennessee (under contract to Bauer Foundations Corporation) (both owned by the Nashville District of the USACE)."

Jan 1, 2014