Search Documents

By Adel M. Hanna, Ibrahim M. Mashhour

"Collapsible soil is known as one of the difficult soils, which possesses considerable strength when it is dry and significantly reduced when inundated. In practice, in case of a thick layer, pile foundations are often used to penetrate the collapsible soil to firm soil/rock strata. Inundation of collapsible soil is accompanied by a large and sudden settlement, which may significantly increase the negative skin friction and accordingly the drag loads on the pile’s shaft. Inundation may take place from the running surface-water or raising the groundwater. In case of surface water, the amount of settlement varies, depending on the extent of the wetted zone and the degree of saturation in the soil, while rising groundwater will produce full saturation in the ground and accordingly larger settlement.In the literature, there is lack of reports dealing with the prediction of the drag load on piles in collapsible soils subjected to inundation. This is due to the complexity of modeling collapsible soil analytically. Alternatively; the results of a sophisticated experimental investigation may guide the researcher to develop a model to predict the drag load on these piles.This paper presents the results of a small-scale experimental investigation tailored to measure the soil collapse during inundation and the associated drag load on an endbearing pile’s shaft. Based on the results of the present investigation, the effect of the soil collapse potential and the pressure acting on the soil during inundation on negative skin friction is presented.INTRODUCTIONCollapsible soil is a metastable material, traditionally defined as unsaturated soils that experiences a radical rearrangement of particles and significant reduction of volume upon wetting with or without loading (Bara 1976; Houston et al., 1988). A wide range of soils fall into the category of collapsible soil, including naturally existing types of soils such as: Alluvial flood plains, mud flows, residual soils, colluvial deposits, fans, aeolian or wind-blow deposits sands and silts (loess), volcanic tuffs, gypsum, dispersive clays, loose cemented sands , sodium rich montmorillonite clays (Clemence and Finbarr 1981).Soil wetting and soil saturation may take place as a result of urbanization or natural causes, such as: groundwater level rise, landscape irrigation, broken water pipelines or sewer lines, poor surface drainage, groundwater recharge, cut/fill construction, and moisture increase due to capillary rise. The severity of the outcome depends heavily on the so called collapse potential of the soil, which depends mainly on; soil type, compaction effort, initial water content and stress level at soaking (Houston and Houston, 1997; Ayadat and Hanna, 2007)."

Jan 1, 2015

By Joshua R. Omer

A numerical model is developed for predicting the load transfer and settlement behaviour of vertically loaded, bored cast in-situ piles. Based on analysis of full-scale pile tests, closed-form equations are formulated to uncouple the shaft and base transfer resistance components of the pile/soil system. Appropriate parameters are introduced to take into account: (i) the shaft resistance distribution in unlined and partially lined piles, (ii) the effects of ?soft toe? (voided toe pile) behaviour on base resistance development. For convenience, an interactive computer program has been developed in Matlab? with a user friendly interface system. The program can be applied to predict the complete load-settlement curve and axial force distribution in bored cast in-situ piles if reliable soil test data are available. To demonstrate its validity, the proposed method is applied to 4 test piles, which are also analysed using two previously published methods: (a) elastic solution method and (b) layer discretisation method. Methods (a) and (b) above are based on load transfer (t-z) and finite element models respectively. It is shown that the proposed method yields axial force distributions and load-settlement curves that are in good agreement with the observed pile test data.

Jan 1, 2010

By Gordon Chen

As part of a value engineering envisioned by East Coast Slurry, Weidlinger Associates, Inc. designed a unique elliptical slurry wall cofferdam for construction of the 65 ft. deep MWRA North Dorchester Pump Station. A conventional rectangle cofferdam with multiple levels of bracing would have been time consuming and costly and imposed a significant obstruction to the pump station construction. A circular slurry wall, while eliminating the bracings, conflicted with adjacent structures and required excessive backfilling around the final pump station structure. The ellipse shaped cofferdam fit the needs of the project well; however, it created a significant design challenge without the use of bracings. Unlike a circular cofferdam which primarily only has hoop stresses, the ellipse still has to be designed for horizontal bending moments in each panel because of the non-axial symmetric conditions. The more eccentric the cofferdam shape; the higher the horizontal bending. The challenge was to develop a three dimensional finite element model that could analyze both the hoop stresses and horizontal bending stresses above and below the bottom of excavation induced by soil and water pressure and unbalanced construction surcharge loads. This paper discusses the techniques used to model the soils and structure interactions and results of stresses on this challenging unbraced configuration.

Jan 1, 2010

By Huw Williams

"Power companies are always looking to increase the carrying capacity of existing transmission lines, and the preferred method is to string heavier capacity conductor lines. However this results in higher wind loading and the potential for towers overturning, if the existing foundations do not have the tensile capacity. On older lines, there is often a lack of information on construction type and dimensions and in practice the as-built foundation can differ considerably from design drawings, due to unforeseen ground conditions along the line route, and no record of the resulting change in design being made.Following successful trials in New Zealand, integrity testing with Frequency Response and impedance profiling techniques is now being used in the region to check concrete foundation properties in-situ and are enabling power companies to get the most out of their assets. INTRODUCTIONIn most regions of the globe, the US included, there is generally a requirement to upgrade transmission line capacities, to cope with increasing power consumption. Problems with under capacity only come to light for the public when blackouts occur, even in developed countries.A large number of transmission line towers are designed with a certain capacity redundancy and will be able to carry greater loads than originally designed for. Power companies are therefore looking for ways to assess their assets and to minimize the costs of upgrade work.Re-assessment of tower foundation capacities using design drawings may not be valid , as constructed foundations may differ considerably from design drawings, to accommodate local difficulties and in some instanced, particularly with earlier lines, there is no information whatsoever. This complicates efforts to determine the capacity of foundations considerably."

Jan 1, 2005

? Hollow Stem Auger ? Drill Bits ? Leads/Torque Arm ? Hydraulic Gearbox ? Hydraulic Power Unit ? Grout Pump ? Crawler Crane

Jan 1, 1998

By Ramin Motamed, Anna Panorska``, Joseph A. W. Toth

In this study, a dataset of 145 bi-directional and static load tests was used to evaluate the load-displacement response with respect to unit side resistance for drilled shafts comprising fully and partially mobilized data. A total of 612 unit side resistance curves were calculated which included 52 fully mobilized curves showing a maximum response. A new approach using the double tangent method, is proposed in calculating the maximum unit side resistance from partially mobilized load-displacement data. The double tangent method was applied to each load-displacement response to estimate the ratio of mobilized resistance between the intersecting tangents and peak measured resistance. It is observed that as the mobilization of side shear approaches a maximum, the ratio approaches unity. Using the fully mobilized curves, regression models were developed using correlations between ratios of estimated resistance at the double tangent, peak, and maximum measured responses. Regression models are evaluated for the following factors: predominant soil type and drilled shaft construction methods. Comparisons of calculated and measured maximum values of unit side resistance are compared for each model. Although these factors each influence the load-transfer behavior, a single global regression model including all the data showed promise in yielding accurate results.

By Michel Bustamante

The original Cistercian Lure abbey situated in eastern France and built in the second half of the 16th century, has become nowadays an administrative building. Because it has been founded on poor ground conditions and inadequate foundation scheme, the abbey has suffered severe structural distortion. In 1992 an inspection revealed new extensive damages which led to a general refection together with a foundation underpinning. Micropiling was the selected method. Movements recorded over a period of 6 years after underpinning completion are presented.

Jan 1, 2002

By Philip Derbyshire, Dale J. Scheffler

"Continuous Flight Auger (CFA) piling is a variation of Augered Cast-In-Place (ACIP) or augercast piling. In both cases a continuous auger with a hollow stem is used to drill a hole and a pile is formed by injection of cementitious material through the hollow stem as the auger is withdrawn. CFA differs from conventional American ACIP by the use of concrete rather than grout to form the pile, and by the type of equipment used to advance the auger into the ground and withdraw it. CFA installation uses a European style rig (i.e. fixed mast and rotary system) which can produce greater crowd and usually has a larger rotator or drill motor than the standard augercast setup. A standard augercast setup will consist of a lattice-boom crane and a set of leads to house the drill motor and auger. The auger size will range up to 24 inches (610mm). With CFA rigs larger diameter piles can be constructed, 24 to 36 in dia. (610mm to 915mm) are common and the technique has been applied with diameters up to 48-inch (1220mm). CFA makes use of sophisticated computer controlled monitoring systems, which have more recently been introduced for conventional ACIP piling. Developments in CFA have taken place over the last 25 years in Europe and particularly in the UK, but are relatively new in the USA. One application is in the construction of secant (overlapping) piled retaining walls. D.J. Scheffler Inc. recognized the potential of the CFA system following visits to the UK and has introduced its use into California for both secant piling and other applications.BACKGROUNDThe high price of real estate in many of the favored areas of California has increasingly led owners to want to build basements under their houses to increase the floor space available on a lot. Many of these areas are by the coast where the ground conditions are predominately granular and the water table is high. Conventional shoring and dewatering systems have often caused problems with adjoining properties. Clearly tangent walls are not suitable in these conditions because of leakage and loss of ground. The secant pile system, using CFA techniques, has proved very effective at overcoming the problems experienced by other methods. Other applications for CFA secant walls have included use for an emergency job on a highway following erosion caused by unusually heavy rainfall.METHODThe concept of secanting piles, whereby primary(female) piles are installed first and then secondary (male) piles are cut into the primary piles is not new. The method has been known for more than 30 years. Originally ‘Benoto’ grabbing rigs, developed in Japan, were used together with sectionalized double skinned casing and oscillators.This early method was slow, although very effective. More recently high torque rotary machines have been used. Contractors in the UK have increasingly used CFA techniques to further improve productivity of this type of piled wall. The improved capabilities of piling rigs available, as well as developments in concrete technology and instrumentation, have made this possible."

Jan 1, 2005

By H. S. Radhakrishna

Foundations supporting power transmission and communications towers are subjected to both compression and uplift loads, often of a cyclic nature. Some novel foundations, combining the beneficial features of grouted and helix anchors with that of compression piles and grillages, were developed by Ontario Hydro during the construction of high voltage transmission lines in Ontario, Canada. In addition to meeting the load requirements, the foundations permit easy installation in swampy areas and also minimize impact on environmentally sensitive terrain. This paper describes the features of these composite foundations and outlines the performance criteria used for their design and installation on the basis of load test results.

Jan 1, 2010

By M. Meckkey El Sharnouby

In this paper, the results of full-scale field testing of reinforced helical pulldown micropiles (RG-HSP) installed in clayey till soils and resting on sandy soils are presented. Piles were tested under monotonic and two way cyclic lateral loadings. Effect of different loading setups on the results is demonstrated. The factors affecting the piles' performance are discussed. It was found that under monotonic loading the piles were able to sustain displacement up to 50% of the grout shaft diameter. Under low cyclic loading levels, the piles did not suffer degradation in the performance. Also, the degradation rate during cyclic loading increased with the increase of the load level. The experimental results show that the reinforced helical pulldown micropile is a reliable foundation option for lateral monotonic and cyclic loading applications.

Jan 1, 2011

By X. L. Chen

The diaphragm walling has been recently adopted in one of the largest excavation of deep foundation engineerings in Shanghai, China with dimension of 90m in length, 50m in width and 13m in depth to solve its stability problem. In this paper the field test for monitoring the stability of the diaphragm wall is discribed, in which the excess pore water pressure and the horizontal displacement of the clay layers were monitored during the period of the excavation. The data measured in the field test are efficient for the safety during construction.

Jan 1, 2010

By Gregory A. Stephan

A case history of design, prediction, instrumented static load tests on probe piles, installation monitoring, and integrity testing of production piles is presented. Based upon project-specific subsoil conditions, as obtained from several 60 to 80 ft (18.3 to 24.4 m) deep test borings, deep foundation system alternatives included driven concrete and steel pipe piles as well as augered cast-in-place (ACIP) piles. High structural loads, site-specific constraints, and the production time frame mandated by the project owner led to the selection of an ACIP pile foundation system that was designed for a pile capacity of 75 tons (667 kN) in compression and 35 tons (309 kN) in tension. Site-specific concerns were raised about the highly porous nature of fragmented and decomposed sandy limestone as well as the high grout intake during construction that could result in increased foundation cost as well as interconnecting of the piles in the rock layer. Consequentially, a multi-phase ACIP pile evaluation program consisting of instrumented compression pile load tests, in conjunction with single-hole ultrasonic pile testing, pile echo testing (sonic testing), as well as full-time production pile monitoring by an experienced geotechnician was specified. As a result of this testing and evaluation program, while grout usage was determined to be within an acceptable range, the instrumented compression load tests yielded data that allowed use of 55 ft (16.8 m) long ACIP piles in lieu of the original plans to use 70 ft (21.3 m) long precast concrete piles. This information was effectively utilized as part of the overall quality control program to install a total of 268, 14 in. (356 mm) diameter ACIP piles within the building footprint to depths of 55 ft (16.8 m) below the pile cut-off elevation as part of the foundation support system. Information recorded during installation included rate of insertion/extraction of the auger, grout pump strokes and pressure, total grout volume, and grout factors, as well as quality and strength of grout. Additionally, many pre-selected installed piles were tested for integrity with a Pile Integrity Sonic Analyzer (PISA) using both sonic and ultrasonic methods. This engineered, monitored, and tested foundation solution provided an effective and quality intensive basis for completion and approval of the foundation work for the building that resulted in cost savings over other foundation alternatives for the owner.

Jan 1, 1999

By Jorj Osterberg

550 load tests of up to 150 MN have been completed on driven and bored piles using the Osterberg Load Cell. Because the test measures side shear and end bearing separately, much can be learned about the forces on the pile as it is loaded to ultimate capacity. At working loads side shear almost always far exceeds end bearing, with the distribution of shear and bearing greatly affected by disturbance occurring during drilling operations. Since much less movement is required to mobilize side shear than end bearing, most of the bearing develops after the working load is exceeded. Thus with insufficient bottom cleaning, safety against excessive settlement can be considerably reduced. Improved methods of drilling, hole cleaning, rebar cage installation and concrete placement are discussed. For rock socket piles it has been found that the ultimate test load far exceeds the working loads in most cases. This is almost always due to greater penetration into the rock than is required for adequate safety against excessive settlement. Factors affecting rock socket capacity are discussed. Increase of side shear and ultimate capacity with time is discussed. Case histories for driven and bored piles in soil and rock sockets are described.

Jan 1, 2001

By Alexander Blatt, Franz-Werner Gerressen

Diaphragm wall technique is usually used to construct structural elements in the ground, commonly used for retention systems, permanent foundation elements or deep groundwater barriers, named Cut-Off-Walls (COW). Recent developments proof, that the technology also satisfies the demands for using the diaphragm wall technique for bulk sampling purposes. Such kind of new ideas required the adaption of equipment and tools for a depth capability never reached before by a trench cutter in any commercial application worldwide. Compared to the development of increasing depths, especially inner-city applications with limited space, demand a minimization of equipment to accommodate such projects. The paper will focus on the developments and solutions generated to fulfill these requirements and will give an outlook to future developments. Further it describes finalized reference projects and will give a general outlook on future trends and developments. The Paper/The Presentation explains as well the installation process in general.

May 1, 2022

By Juhyung Lee

Recently, large diameter drilled shafts are often used for foundations of large-scale marine bridges with high capacity and required to resist lateral loads. Steel casings are essential in supporting the hole-diving concrete installation of the drill shafts constructed in the sea. The casings, however, are usually not considered as the structural elements and their load bearing capacity is often overlooked in the design of drilled shafts. As the diameter of drilled shafts becomes larger, there are higher demands for more efficient and economical design of large-scaled drill shafts in the sea. Steel-concrete composite columns are popular for the superstructure of bridges, and the outer steel attached to the shaft increases the shaft resistance through confining the concrete. In this study, the lateral resistance of steel-concrete composite drilled shafts was evaluated quantitatively based on the numerical analysis. When steel casings are used as structural elements such as the composite columns. Ultimate lateral bearing capacity of composite drilled shafts with various diameters was numerically calculated through the 3D finite element analysis. For that, elasto-plastic model with the perfect plasticity is involved to capture the ultimate load. A commercial FEA program, MIDAS-GTS, is used in this study. Real field conditions of the west coast, Korea were examined to set up the ground conditions and pile lengths required for this parametric studies. Detailed characteristics of the stress and displacement distributions are evaluated for the better understanding on the mechanisms of the composite shaft behavior.

Jan 1, 2008

By George Piscsalko

Quality control of drilled shafts and ACIP piles is greatly dependent upon the practices of the site personnel. In many applications it is difficult to properly inspect the shaft prior to concreting, such as when the shaft is drilled under slurry. In other cases, such as ACIP piles, it is impossible to inspect the shaft in any manner prior to concreting. There are numerous methods currently available to assess the integrity of drilled shafts and ACIP piles. Each method has its advantages and limitations. This paper will compare the various available methods as well as introduce a new method for assessing integrity in drilled shafts and ACIP piles. This new method, known as Thermal Integrity Profiling, determines the integrity over 100% of the shaft both inside and outside the reinforcing cage by measuring the hydration temperature of the concrete along the length of the shaft. These temperature measurements can be made by either passing a thermal probe through a standard Cross Hole access tube typically 12 to 48 hours after concrete placement, or from embedding thermal wires within the shaft prior to concrete placement and monitoring them with unattended data collectors for 12 to 48 hours after concrete placement. This Thermal Integrity Profile method will be described in detail and several case histories will be presented. Additional testing methods which will be compared include low strain Pile Integrity Testing, and Cross Hole Sonic Logging. Advantages and limitations for each method will be discussed.

By Abolfazl Eslami, Sara Heidarie Golafzani

CPT-based methods considered as complementary tools for static analyses outperform other axial pile bearing capacity predictive methods. Considering soil spatial variability and minor errors associated with procedure and operator, CPT-base methods mitigate the effect of latent uncertainties in pile design. These methods were developed based on different databases and purposes. Hence, several statistical and probabilistic attributes were defined and implemented to assess the predictive CPT-based methods’ performance via CPT and pile databases in terms of the model parameter. These features make a comparison among methods in terms of precision, accuracy, and efficiency. Furthermore, CPT-based methods can be subjected to scrutiny over their backgrounds and how they were developed via reliability analysis. In this regard, a database of sixty-two driven piles and their adjacent CPT soundings were gathered, and six commonly applied CPT-based methods were examined according to criteria other than prevailing statistical and probabilistic ones, including; (a) input variables, (b) soil behavior classification (SBC) (c) model assumption (d) Influence zone, and (e) axial loading direction. According to these introduced criteria, CPTbased methods were classified and appraised via efficiency ratio. Eventually, these reliability-based, statistical, and probabilistic criteria evaluate the understudied methods performance for the investigated compiled database and help designers select consciously appropriate predictive methods according to the site conditions.

Sep 8, 2021

By Emad Farouz

This paper presents a case history of a successful construction-phase pile load test program that optimized the pile design in challenging ground conditions at the Great Neck Wastewater Treatment Plant in the Town of North Hempstead in Nassau County, New York. The improvements and expansion of the wastewater treatment plant included the construction of several new structures to comply with new stringent nitrogen discharge requirements and new design flow. The challenging ground conditions included up to 20-ft thick organic deposits with weight of hammer blow counts and up to 14 percent organic content and tidal ground water that was near the ground surface. The foundation design evaluated various deep foundation alternatives and selected driven closed-ended pipe piles then filled with concrete as the most suitable foundation. The selection process included considerations of cost, risk, vibrations, noise, and schedule. The contract documents utilized an innovative approach of performing an optimization load test program that was implemented during construction to optimize pile lengths and reduce potential vibration and construction schedule. This paper discusses the details of the successful load test program including static testing, dynamic testing, and the innovative contracting approach utilized to implement the construction phase load test program. It also discusses the successful development and implementation of driving criteria for production piles and construction challenges. The successful load test program resulted in savings of several hundred thousand dollars, optimized schedule, and lower environmental impacts.

By George Piscsalko

"Quality control of drilled shafts and ACIP piles is greatly dependent upon the practices of the site personnel. In many applications it is difficult to properly inspect the shaft prior to concreting, such as when the shaft is drilled under slurry. In other cases, such as ACIP piles, it is impossible to inspect the shaft in any manner prior to concreting. There are numerous methods currently available to assess the integrity of drilled shafts and ACIP piles. Each method has its advantages and limitations. This paper will compare the various available methods as well as introduce a new method for assessing integrity in drilled shafts and ACIP piles. This new method, known as Thermal Integrity Profiling, determines the integrity over 100% of the shaft both inside and outside the reinforcing cage by measuring the hydration temperature of the concrete along the length of the shaft. These temperature measurements can be made by either passing a thermal probe through a standard Cross Hole access tube typically 12 to 48 hours after concrete placement, or from embedding thermal wires within the shaft prior to concrete placement and monitoring them with unattended data collectors for 12 to 48 hours after concrete placement. This Thermal Integrity Profile method will be described in detail and several case histories will be presented. Additional testing methods which will be compared include low strain Pile Integrity Testing, and Cross Hole Sonic Logging. Advantages and limitations for each method will be discussed.IntroductionDrilled shafts and Augered Cast-in-Place (ACIP) piles have been increasingly used over the past several years due to several reasons including the reduced noise and vibration, speed of installation for ACIP piles, and the large axial and lateral capacities which are attainable for very large drilled shafts. ACIP piles are drilled and cast without any visual inspection. Drilled shafts can be cast in a dry hole which allows for inspection of the hole prior to casting, but the casting process is very difficult to nearly impossible to inspect with any accuracy. Drilled shafts are frequently cast under slurry as a means to stabilize the surrounding soils during the construction process. When casting a drilled shaft under slurry, it is very difficult to accurately inspect the hole prior to casting and it is equally difficult to inspect the shaft during the casting process. Many of the above mentioned processes are blind to inspection and therefore the chances increase for having defects present in the completed elements."

Jan 1, 2017

By David S. Graham, Benjamin Turner, Paul J. Axtell

Seismic challenges were at the forefront of design for two parallel replacement bridge structures over the Arkansas River as part of the I-30 Crossing Project in Little Rock, Arkansas. Although not an area of the country typically associated with high seismicity, proximity to the New Madrid Fault Zone resulted in design ground motions sufficient to trigger liquefaction in alluvial channel and point bar deposits. A detailed post-award subsurface investigation program utilized CPT with complimentary borings to obtain samples for laboratory testing to assess the continuity of potentially liquefiable layers, from which we concluded that continuous zones of liquefaction across the extent of the north approach could lead to lateral spreading towards the river. An overview of the foundation and superstructure design to resist lateral spreading forces in accordance with the latest published design guidelines and research is presented. Other seismic aspects of the design are covered including timber pile ground improvement to mitigate liquefaction at the north approach embankment and foundation input motions that differ from code-based ground surface motions due to foundation stiffness, strength, and geometry. The project showcases an example of successful collaboration between geotechnical and structural designers with contractor input to address seismic challenges in the South Central US. Furthermore, the importance of considering kinematic demands on columns and other superstructure components – not just foundations – is highlighted.

Sep 8, 2021