Search Documents

By J. Ling, L. Racine, P. Cousin, A. R. Laplante

"The problem of gold recovery by gravity from high density gangues is first discussed from a fundamental perspective. Three potential difficulties are presented: poor liberation and fine gold particle size, concentrate bed erosion by coarse dense particles, and slow percolation of gold particle through the high density gangue bed. Two case studies are presented to illustrate the impact of these three problems on circuit performance and the feasibility of gravity recovery. It is concluded that careful testing can determine the scope of the first problem and feed preparation can limit the extent of the second. The third problem is clearly the most serious and results in lower gravity recoverable gold recoveries than would be achieved with the same recovery effort on a low density gangue application.IntroductionSince the commercialisation of the Knelson Concentrator in 1980, gold gravity recovery has experienced a surge in interest, in Canada and the United States first, then Australia, Zimbabwe and Russia, and finally worldwide. Table I details number of units sold in various countries, which corresponds approximately to their importance as gold producers 1. Exceptions. such as the low rank of South Africa or the importance of Zimbabwe, despite the much higher gold throughput of the former, are generally the result of differences in the effectiveness of the local marketing strategies, as well as a reflection of the ""philosophy of recovery"" prevalent in the country.The impact of the Knelson has not been felt equally in all plants. Typically, a highly successful application falls into the following categories: (a) alluvial or hard rock recovery for which gravity is the sole recovery method, (b) hard-rock free gold milling with ores which have a very high gravity-recoverable gold (GRG) content, (c) low grade sulphide copper-gold ores which include flotation ahead of cyanidation and (d) free-milling gold ores ahead of Other applications can be successful, but are not as common. The ""explosion"" of centrifuge concentration, of which the Knelson is the most successful but by no means the sole model, has created a certain euphoria which can be summarized as ""gravity recovery will improve the profitability of gold milling, no matter what."" This presentation is about applications that are not so successful, or even downright unsuccessful. The rationale is not to down-play gold gravity recovery, but to set it in its rightful position: metallurgically, it is not appropriate all of the times; it can become inappropriate if poorly designed; and it can be metallurgically possible but economically unjustifiable. In this paper, this will be illustrated and explained rather than demonstrated, with the use of both industrial plant surveys and laboratory test work. Alternate gravity approaches will be suggested."

Jan 1, 1997

By U. Dillon, G. Blackwell

"Geographic information systems (GIS) provide an efficient means for the recording, manipulation, revision, display and analysis of spatially referenced data. GIS are widely used at the exploration stage of mine development, and are increasingly used for reclamation planning. The ability of a GIS to perform spatial searches and query spatially referenced data make it a powerful tool for use at all stages of mine development. As the amount of data available for analysis increases, so does the power and flexibility of GIS as a planning tool.Starting from the exploration database, this paper describes how a GIS can be used for the development of mining plans based on topography, geology and mineralization information stored in a relational database. Planning decisions approaching the optimal can then be made for a wide range of parameters, including stockpile and waste dump locations, the location of potentially acid generating and neutralizing material for dump design, profitable and risk-controlled mine extraction sequencing, and haul road locations. This is made possible by the overlay and buffer analysis capabilities of a GIS which are explored and exploited to produce a continuous mine production planning program, as well as site remediation and reclamation using a successful case study. IntroductionGeographic information systems (GIS) are a relatively new tool in the mining industry. Although they have existed for a number of years, the potential of GIS for mine management and planning is only beginning to be investigated and exploited. The unique spatial capabilities of GIS make them particularly wellsuited for use in mining, where spatial information is fundamental to the processes of mineral exploration, mine development, and environmental reclamation. A number of potential applications for GIS in the mining industry have been identified, and they are widely used for exploration and reclamation. The use of a GIS as a platform for the development of mine planning routines and software remains an interesting, but as of yet unexplored, application of this technology."

Jan 1, 2003

By Gregg Vickell

"High tonnage, low grade gold mines such as Omai’s afford economies of scale that are unto their own insufficient to sustain profitability at today’s depressed gold price. Complimenting profitability objectives is the perpetual challenge to reduce operating costs and optimize unit operating efficiencies while being ever vigilant of issues such as environmental control.Key to achieving these objectives at Omai are throughput and availability gains, gold recovery improvements, cost cutting, a skilled workforce and reliable power generation.This paper attempts a cursory review of startup-to-date plant performance advances and future performance-driven objectives.INTRODUCTIONCommercial gold production at Omai commenced in January 1993 with annual output climbing to 250,000 opy by the end of 1994. A mill expansion completed in August 1996 increased gold production to 340,000 opy by the end of 1997. Current milling capacity is 20,000 in tpd (nom.) with actual capacity exceeding 24,000 mtpd on occasion depending on ore size and competency. Mill feed consists of hardrock (andesite, quartz diorite and rhyolite) and softrock (saprolite, laterite) at a nominal ratio of 70:30, respectively. Present day average weighted grade of the feed is 1.4 g/t gold.PROCESS DESCRIPTIONPrimary crushing, ore handling and the original 12,000 mtpd hard and soft rock SABC mill, hereafter referred to as Mill ‘A’, remains essentially as documented by Konigsmann (1 994) complete with poststartup modifications. The mill expansion, hereafter referred to as Mill ‘B’, features an 8000 mtpd hard rock SABC grinding circuit similar in configuration to Mill ‘A’ and differing only in equipment size. Mill ‘B’ includes a 9000 H.P.,reversible variable speed , single pinion drive, 32 ft. x 15 ft. SAG inill , a 7 ft. short head pebble crusher and two parallel 5400 H.P., 16.5 ft. x 30 ft. ball mills with dedicated cyclone packs consisting of D26 hydrocyclones."

Jan 1, 1999

By R. L. Amelunxen

"In January 1983, Gibraltar Mines Ltd. started an exploratory program on Column Flotation with hopes of improving performance of the Molybdenum Cleaning circuit. The encouraging results led to a column test trial in the Bulk Copper Cleaner circuit where the test unit has per¬formed well. A program was undertaken to understand the mechanics of column operation. A year and a half later, Gibraltar is considering the replacement of existing Bulk Copper and Moly Cleaning flotation cells with a fully computer con¬trolled Column Flotation circuit.BRIEF SUMMARY OF TESTWORKInitial testwork was done with a home made 20 inch diameter x 31 foot high column, equipped with a doppler flow-meter at the tail line and automatic level conrol. This loop maintained constant level in the column by throttling the tail valve. This column was placed in a variety of locations around the Moly circuit as shown on Figure 1 a, b. Test re¬sults indicated that the column could achieve much higher grades than the conventional cells, but recovery wise, the performance was low. Spillages from overloaded pump boxes were a common frustration during this time.Column control strategy was reviewed; and, in light of information received from McGill University, changed to conform with the methods that had been employed by D. Wheeler, of the Column Co. of Canada4 and Gaspe Copper Mines3.The column was tested replacing a portion of the bank, figure lc. The results obtained were more or less equal to the circuit. However, as we had Nitrogen gas connected to the column and not the regular cells, the column was kept in service. With the use of Nitrogen in the column, the usual copper depressant, Sodium Cyanide could be replaced with Sodium Hydrosulphide, hence lower operating cost.As time went on, a 10 inch diameter column was added in series to re-treat the concentrate of the 20 inch diameter column with hopes that the copper content would decrease from 0.6% down to 0.3% in order to save on subsequent leach¬ing costs. So far, results indicate there has been some im-provement, hut we are not achieving 0.3% copper. (See figure 1d)."

Jan 1, 1985

By Fidelis T. Suorineni

The Ashanti mine, located in Obusai, Ghana, West Africa, has been in production for over 100 years, and is currently the second largest single gold producer in Africa. The mine covers a concession area of 434 square kilometers with four main ore types: the quartz vein type, disseminated sulphide type, supergene sulphides and transition ore, and granitoids stock works (visible gold and quartz veinlets). Various mining strategies and methods have been employed for the mining of the narrow-vein ore at Ashanti. In recent years, the mine owner: Ashanti Goldfields Company Ltd. has embarked on a mine-wide expansion program to boost production to a target of one million ounces per annum. With the rapid depletion of its high-grade ore, a suitable mining method was required to produce a high tonnage at low cost to meet production objectives. This paper discusses how the Ashanti mine applied Canada experiences in mining technology to boost production, and the impact that the differing geological settings between the two countries had on the stope performance at the Ashanti operations. Experience developed at the Ashanti mine led to innovative modifications for stope layout and design methods in relatively poor ground conditions.

Oct 1, 2001

By R. D. Brown

"AbstractIn order to raise the enormous amounts of capital which will be essential for the development of Canada's mineral and petroleum resources, this country's resource industry must be permitted to earn an acceptable rate of return. The existing tax regime, with its high rates, complexities and misdirected incentives, presents a serious obstacle to our resource industries in their development of Canada's immense , but increasingly lean, resources. Government tax and other policies are not the only cause of the crisis now facing the resource sector in Canada, but a reformed tax system, with stable and reasonable tax burdens, is required if Canada's resources of minerals, oil and natural gas are to continue to contribute in the future, as in the past, to our national well-being.An independent task force, organized under the auspices of the Canada West Foundation, has recently completed a wide -ranging report: on the future development of Canada's mineral, oil and gas resources. This five-volume report, completed after almost two years of research and study, concludes that Canada •is facing a major crisis •in the development of our resources, It states that unless corrective action is taken now, mineral production and exports could decline drastically after 1985, at the same time that Canada would face massive bills for imported oil because of inadequate and declining production.The task force, chaired by the author of this article, has put forward recommendations for a fundamental shift in both federal and provincial policies in order that Canada's mineral reserves can be developed in the national interest. This article consists of excerpts from the summary of the task force's report."

Jan 1, 1977

By G. R. Brough

"Today it is more important than ever to get the maximum possible return on capital invested in the processing industry. To this end the plant is often operated continuously and the choice of equipment is, consequently, extremely important.Screening spans a wide range of particle sizes and there are many different types of screening elements. The following types are common:1. Cloths and elements of rubber.2. Wire mesh screens with round wires.3. Wire mesh screens with profiled wires.4. Perforated steel plates.5. Elements of plastic.6. Gratings of steel beams.7. Gratings of iron rods.We would like to deal with two of these types namely rubber and briefly on plastics.We first introduced rubber screens to the Canadian Mining Industry in November, 1963. This stemmed from a conversation with the superintendant of one of Canada's largest screening plants containing 48 vibrating screens, with an average wire cloth life of 10 to 12 days. We contacted the manufacturer of rubber screen cloths who had supplied rubber screens to a mine in Northern Sweden for a 50,000 ton per day plant in 1951."

Jan 1, 1983

By Constantin D. Pitis

Similarly to notions of constant capital/expenses in business or magnetization power for electric motors an energetic base load (E0) is always necessary to set up a mining process. Denominated as ?non-productive energy? or base load, (E0) is a constant component of the entire energy consumption of the process, while another component the ?productive energy? (Ep) is variable, being function of the production/throughput (M). By using these new concepts, the author creates an energetic model proposing a new method of assessing changes in mining processes (throughput) that can reveal possible energy savings (DSM component) or energy losses. Proposed mathematical model of assessing (E0) and energy savings by using ?Marginal Energy Usage Index? (MEUI) enables creation of historical benchmarks and direct on line energetic (efficiency) assessment of mining processes and/or equipments. The paper analyses the case of assessing possible energy savings that can be obtained by: ?? Improving efficiencies of various equipments (by retrofit) ? reducing E0 ?? Improving the process control or other process changes ? reducing Ep ?? Monitoring persistence of the adopted Energy Conservation Measures (ECMs). For the new plant design, the proposed method enables prediction of Customer Baseline in various mine/process configurations. The method could become part of a ?preventive action? in design process by offering a reliable tool of assessing additional financial effort (Incremental cost) when choosing various higher efficiency equipments and/or processes.

Oct 1, 2009

By R. D. Lawrence

"Comparable transaction analysis is the best known of the market approaches to valuation of exploration-stage mineral properties. The analysis of option and farm-in agreements can also provide useful guidance to valuators. While such approaches can be distorted by incomplete analysis, market-based methods are capable of providing consistent, credible results when carried out carefully with due consideration paid to all factors which buyers and sellers consider when dealing in the real market. IntroductionMineral properties without defined resources present one of the most challenging tasks to the mineral valuator. This paper will concentrate on market-based approaches to valuation of such properties. Other authors at MM2000 presented papers on cost and income approaches. Sorentino (2000) also provides a useful overview with some provacative commentary on methods.Market based-approaches are based on the principle of substitution and include such techniques as: comparable transaction analysis (sometimes referred to as sales comparison analysis); farm-in commitment (or option agreement) analysis; rules-of-thumb; and comparable market value analysis.Are there any valuation standards available to assist the valuator? In Canada there are none that apply to the valuation of mineral assets or securities. This problem is being addressed, at least in part, by the CIMVal Committee of the Canadian Institute of Mining, Metallurgy and Petroleum (CIM)1. Further, the recently established Canadian Association of Mineral Valuators will be giving consideration to the adoption of valuation standards."

Jan 1, 2002

By Gerald Whittle

What is Enterprise Optimization? Releasing value through better planning decisions: Philosophy, Methodology, Software The key to 5% -35% increase in enterprise value (NPV) The culmination of 25 years development in optimization for the mining industry ?Jeff Whittle Simultaneously optimizing: ?all steps in the value chain ?all assets in the enterprise portfolio ?all periods together

May 1, 2010

By Luis Bernal, Pertti Lamberg

"SkimAir®, Outotec’s Flash Flotation unit, is placed in the grinding circuit to float the valuable liberated mineral particles from the circulating load of the grinding process while still relatively coarse. Esperanza copper-gold deposit located near Sierra Gorda, Chile, hosts 535 Mtn ore grading 0.57 % copper, 0.27 g/t gold. A series of laboratory and pilot flotation tests were conducted to find out the flotation performance of different ore types both with and without the Flash Flotation. This data was used in modeling and simulating to find the optimal flow sheet for the highest Au and Cu recoveries with required Cu concentrate grade. Simulations with the HSC Chemistry 6.1 software showed that with the SkimAir® and Flash Cleaning it is possible to achieve the required copper grade of 27% Cu with 5% higher recovery for gold and 2% higher recovery for copper compared to the circuit without the Flash Flotation. The pilot tests with simulations were the back up for the installation of four Outotec SkimAir® SK 2400 Flash Cells in the Esperanza circuit for the processing 95.000 tpd of copper-gold ore.INTRODUCTIONEsperanza copper-gold deposit is located near the town of Sierra Gorda, 2nd Administrative Region in Chile. Deposit hosts 535 Mtn ore grading 0.57 % copper, 0.27 g/t gold. The main copper minerals are chalcopyrite and bornite. Gold is carried by native gold and solid solution of copper.Antofagasta Minerals S.A. conducted a series of flotation studies at SGS Minerals Services. The studies included both laboratory and pilot scale work. In the pilot scale study the applicability of the Flash Flotation technology was studied with High-grade Andesite and High-grade Porphyry samples (SGS Mineral Services). The Flash Flotation technology gave significantly higher recovery for gold than the conventional flotation circuit. The recoveries for copper were slightly higher using the conventional flotation."

Jan 1, 2009

A direct comparison has been undertaken between laboratory wind tunnel experimentation and computational fluid dynamics simulation of a 3D manufactured analogue for a body of fractured broken rock, created with CAD/CAM techniques. Detailed descriptions of the ?design? of the analogue (using a discrete element analysis multi-body simulator), its manufacture (using computer aided design and 3D printing technology) and the laboratory experimentation (inserting the physical analogue into a laboratory scale wind tunnel) are presented. The agreement of the results of direct experimental observations on the manufactured analogue with the values from CFD simulations of those experiments justifies the utilization of a CFD environment for the practical investigation of geometric factors controlling air flow and heat exchange in complex assemblages of broken rock blocks. The ultimate goal is described, that of developing functional relations between bulk properties of such assemblages (such as their porosity and bulk density) and the low-level geometric factors that dictate the air flow behaviour, such as the equivalent perimeter length of the cross-sectional area available for flow, or average flow path tortuosity. A practical application area of the work in the mining context is also described; equivalent continuum air flow and heat transfer constitutive models developed on the CFD tool from such functional relations are useful in characterization of seasonal heat storage in large scale bodies (approximately 1 km3) of broken rock.

Aug 1, 2013

By H. A. Dakin

"An introduction to the metallurgical requirements of the Flin Flon concentrator reveals the magnitude of ore blending which is required in its operation of three flotation circuits. The resulting variability in flotation heads which has in-creased the separations complexity justified the development of an on-line analysis system.This paper provides a summary of the development and operation of that system. Particular attention is devoted to the problems encountered and where possible their solutions; as the requirements of accurate information and minimum downtime of the sampling system and x-ray analyzer are considered essential. The addition of a recess central computer has provided information in a more easily understood form and as well has allowed the start of automatic reagent control.An indication of the on-line analysis system's value to the concentrators' operation is provided by an examination of the plant in metallurgical data and reagent costs in previous years.The metallurgical plants of Hudson Bay Mining and Smelting lie adjacent to the city of Flin Flon on the Manitoba-Saskatchewan boundary. Plant operations commenced in 1930 treating copper-zinc ore from the local mine. In recent years ore bodies near Flin Flon and in the Snow Lake area, about seventy-five miles east, have been brought into production.By the beginning of 1973 the number of producing mines had increased to nine; with all the ore being handled by the Flin Flon concentrator. Figure l, showing mine ore assays during 1973 indicates the variation in metal content possible."

Jan 1, 1974

By Claude Bazin

"The On-Stream Analyzer has proven and is still proving to be an extremely valuable tool for the control of flotation circuits. This paper examines the possibility of going further in the utilization of the provided assays using a real-time material balance program to calculate the distribution of solids within the streams of a circuit. Mass balance results can be used for process control, process analysis and detection of sensors malfunction. Examples from 3 Canadian and one American concentrators are presented to illustrate the potential of the method.IntroductionThe On-Stream Analyzer (OSA) has gained, over the last two decades, the status of key instrument for the control of flotation plants. The OSA is currently used in almost every sulphide flotation plant and its application in oxide mineral flotation plants is increasing. On-Stream Analyzers provide X-rays pulse counts that are converted into assays using multilinear regression programs. The estimated assays are passed to the flotation operators, via an operator console, or to control loops of various degrees of complexity (McKee, 1991) implemented in a Distributed Control System (DCS). Operators and/or controllers take control actions based on these assays to ensure an adequate operation of the plant. Although this application pays off very rapidly for the purchase of the OSA, one should ask: Could we get more from the OSA?Some plants reported the use of OSA measurements to process optimization (McKee, 1991). The optimization strategy is based upon economic indices calculated from metal recovery using the 2 product formulae (Wills, 1992, page 124). The 2 product formulae is however sensitive to measurement errors in the assays and can lead to considerable scatter in the calculated indices (Hodouin et al., 1993). Least squares algorithms provide an interesting alternative to filter out measurement errors (Spring, 1992). This paper presents a recursive least squares algorithm that estimates in a real time fashion the mass flow rates in a flotation plant using OSA and mass flow measurements. The algorithm is robust and its recursive structure is not demanding in terms of computation time and memory. The method was tested with data from four concentrators. Results of the material balance algorithm prove to be useful to detect sensors malfunction and may potentially be used for the control and optimization of flotation plants.The paper is divided into two sections. The first section gives a description of the proposed method. The mathematics of the method are kept to a minimum, since the detail is presented elsewhere (Bazin and Franklin, 1994). The second section shows the application of the method to different flotation plants."

Jan 1, 1995

By James Pirie

"The major Archean gold deposits in the Red Lake greenstone belt, which have produced over 374 million grams of gold since 1930, occur near the top of the lower komatiitic to tholeiitic mafic to ultramafic metavolcanic sequence. The upper calc-alkalic mafic to felsic rocks form three discrete and separate ediftces overlymg this lower sequence.The gold deposits are classified according to their stratigraphic or lithologic associations into:1) mafic-volcanic-hosted deposits;2) felsic-intrusive-hosted deposits; and3) stratabound deposits.Group 1 and to a lesser extent Group 2 deposits occur within zones of alteration several square kilometres in extent. The nature of this pervasive alteration can be characterized by comparison of petrochemical data from the altered rocks and their fresher equivalents some distance away. The altered rocks have substantial addition of SiO2> CO2, K2O, As and Sb and subtraction of Na20, CaO, MgO and total Fe. Cr, Ni, Co and Zr appear to have been relatively immobile. Hydrothermal alteration and gold deposition probably accompanied early fumarolic activity and continued during subsequent deformation the metavolcanic sequence, with gold eventually being mobtltzed and concentrated into major vein structures to form the present orebodies. The smaller Group 2 deposits formed by emplacement of felsic intrusions into already altered, anomalously gold-bearing mafic metavolcanics, with the heat from the intrusions setting up parasitic hydrothermal systems which mobilized the gold and deposited it along with minor sulphides in fractures in the cooling intrusions."

Jan 1, 1982

By Mike Robotham

When RFQ?s are received they often contain detailed technical specifications which suggest a departure from the suppliers own customary approach to the design. Both client and end user are quite rightly influenced by their own experiences. The question is who is right, the client and his consultant, the supplier or perhaps a combination of these. This paper looks at some of the fundamental variances that often occur in the approach to the mechanical design of drum hoists, based on our experiences of recent years. Director of Engineering, Mike Robotham is a chartered engineer and has been with DavyMarkham for over 30 years. Having completed a craft apprenticeship he later joined the engineering department as a junior engineer. He has a wealth of experience of working on medium to large engineering projects in the field of mechanical, electrical and hydraulic equipment

May 1, 2011

"Canada Centre for Mineral and Energy Technology (CANMET)Natural Resources CanadaMining and Mineral Sciences LaboratoriesA. Address and Contact Information555 Booth StreetOttawa, Ontario, Canada, KIA OGlWebsite: http://www.nrcan.gc.ca/Contact: Philippe Dauphin, Manager, Business DevelopmentTel.: (613) 947-0798Fax: (613) 947-0984E-mail: pdauphin@NRCan.gc.caB. Type and Size of FacilityScope of facilitiesCrushing from minus 4 in. to 10 mesh; grinding - rod, ball, vibration, SAG and impact mills; classification- screening, cycloning, mechanical, hydraulic and dry centrifugal classifiers; froth flotation - automated, column, and frothless flotation; gravity separation- wet and dry; magnetic separation - high gradient, high and low intensity, wet and dry; electrostatic separation; heavy-media separation; calcining; cyanidation; thickening; filtration; drying - fluid bed and freeze drying; pelletizing; microwave.SpecialtiesMineral beneficiation research and development; flotation of sulphides - flowsheet improvement, selectivity, reagent selection; novel flotation techniques; analysis of thiosalts formation; use of mineral processing techniques for recycling.Specialized equipmentHigh gradient magnetic separation, Denver XRF on-stream analyzer, automated flotation cell.Complementary support servicesElectron microprobe; SEM; STEM; X-ray diffraction; particle size analyzer; mineralogical and analytical chemistry services; physical chemistry; hydrometallurgy; pyrometallurgy; engineering and economic evaluation; mechanical shops; technical information services and library integrated with the National Library System of the National Research Council."

Jan 1, 2000

By Dayle Denton, Lloyd Buckingham, Kenneth G. Thomas, Jacques McMullen

"The dry grinding and leaching circuits of Barrick Gold’s new Roasting Facility at Goldstrike Mine in Nevada, USA incorporate well proven technologies in a unique combination. During the design of the plant, every effort was made to utilize the best available technologies from the perspective of capital, environment and operating costs.Crushing is a two stage process using gyratory and cone crusher. Ore is stockpiled and then reclaimed to two parallel dry grinding mills. The double rotator dry grinding mills include a drying chamber, coarse and fine compartments and utilize a gearless motor drive (GMD) or “wrap-around”. In-circuit product transfer is accomplished with air slides and bucket elevators. Finished product separation is performed by both static and dynamic classifiers with the final product captured in baghouses. Recycle of unfinished product utilizes cascade chutes.The final ground product reports to two 2000 ton roaster feed silos. The two-stage oxygen flu-solids roasters with their associated gas train are the subject of a separate paper.The cyanide leach circuit is a standard carbon in leach system with circular swept screens for interstage carbon retention. The loaded carbon is sent to the existing Goldstrike autoclave plant for stripping and regeneration. Tails, after cyanide destruction, are deposited in the existing tailings dam with tails from the autoclave facility.Throughout the circuit, Clean Plant Design criteria were used to assure environmental compliance, ambiental acceptability and ensure worker health and safety. The commissioning and operation of the double rotator grinding technology has been very successful at Barrick Goldstrike."

Jan 1, 2001

By Éric Poulin, Simon Gariépy, Mario Paredes Malca

"While the design of a control strategy depends on the available process knowledge, its implementation depends on the available process information. On-line chemical analyzers are today widely spread in the mineral processing industry. A real-time concentration measurement of chemical components is valuable information that could bring control strategies to whole new levels. However, the use of these measures rarely reaches anything more than process monitoring. The reason is simple: the on-line chemical measurements quality is most of the time insufficient to be directly included in control strategies. The choice is then made to let the critical eye of the engineer or the operator appreciates the measurements before making any decision based on it.Data reconciliation through mass balance is a technique today widely used in the mineral processing industry to increase the accuracy and the reliability of plant data, mainly for accounting and survey analysis purposes. Real-time data reconciliation of on-line measurements appears as a natural coupling of technologies that could bring new process optimization trends. Once overcome the technical difficulties, full valorization of the instrumentation investment could be reached.This paper presents the application of real-time data reconciliation for process control and performance monitoring. It proposes a general approach, discusses challenges and illustrates concepts with industry experiences."

Jan 1, 2006

By J. G. George

A brief review of the silver industry is presented to set the stage for the analysis of the distribution of silver production by source from various types of mines in Canada and of the changing relationship between the total output of silver and the total output of base metals. The decline in the average grade of the Canadian mines is also discussed and a trend for the future is proposed. The report then examines in broader aspects the world primary silver production and concludes, in the section on outlook, that the effective supply in primary silver will grow at a rate significantly lower than the growth rate expected for base metals. A cumulative deficit of some 900 million ounces is projected for the period 1975-1980 and a further deficit of some 1,100 million ounces if projected for the 1980-to-1985 period.

Jan 1, 1977