Search Documents

By Hans E. Madeisky, Bruce W. Downing

Abstract-The acid rock drainage (ARD) buffering capacity of mine waste is governed by its bulk chemical composition and its mineral assemblage. Conventional acid base accounting (ABA) tests can be used to predict short-term buffering, but should be used with caution to model or predict the long-term ARD buffering capacity of mine waste. ABA data for mine waste samples from four different deposit types: anorthosite-hosted magmatic sulfide nickel, dunite-hosted magmatic sulfide nickel, porphyry copper-gold, and volcanic-hosted high sulfidation epithermal silver, were compared with whole-rock geochemical and petrographic data obtained from the same samples. Our objective was to devise and test a method of predicting ARD buffering capacity based on bulk chemistry and modal mineralogy. In other words, we developed a quantitative theoretical method for calculating neutralizing potential, relying on easily obtainable and relatively inexpensive whole-rock and sulfur XRF analyses, which could substitute for conventional ABA procedures in situations where these procedures are either too costly or too time consuming. For each deposit type, models were devised that reasonably approximate the net neutralization potential estimated by the ABA data obtained from laboratory tests. Once an appropriate model has been developed and tested, portable X-ray fluorescence equipment, already used for grade control at many mine sites, could provide the wholerock and sulfur analyses required to estimate the ARD potential of the waste material. Although this approach is not intended as a substitute for the legally mandated ABA test procedure, it could facilitate the timely and cost-effective management and mitigation of ARD at a mine site.

Jan 1, 1997

By J. Wong, M. G. Lipsett, L. K. Daneshmend

"Current trends of increased size, complexity, and automation of surface mining equipment necessitate more comprehensive and objective techniques for equipment comparison and selection. The field of reliability analysis provides tools to generate quantitative bases for maintenance and reliability aspects of such comparisons. Results from statistical analyses of failure and repair time data are used to perform the comparison. A case study is presented which analyzes five machines of two different technologies and three different designs.IntroductionThe surface mining industry is currently faced with a rapid evolution in production equipment. The more obvious trend in this evolution is the steady introduction of even larger machines. Parallel, and complementary, to this increase in size is the introduction or adaptation of new technologies. Together, these two trends result in new surface mining equipment designs; these designs are often more complex and may feature technologies that have yet to be proven for the application or at the scale they are now fielded.The prospect of significant automation of open pit equipment is also bound to add complexity to future equipment designs. Semi-automated features, such as drilling controllers (Aquila, 2000), have already been commercialized. Fully autonomous haul trucks have been demonstrated in open pit mines (Jackson and Zoschke, 2000). Design concepts for comprehensive teleoperation of open pit operations have been formulated (Lipsett, 1998).With this rapid availability and deployment of new technology and equipment, managers and maintainers are faced with a multitude of decisions regarding what equipment to acquire and what maintenance strategies to implement. In light of this evolution in mining equipment, it is necessary to develop better methods for making equipment management decisions (Dessureault et al., 1999; Paraszczak, 1999). The incentive for development of such techniques is that a large portion of an open pit mine’s operating cost is maintenance related, as shown in Table 1."

Jan 1, 2000

By G. Goodall, R. Jabbar, S. Muinonen, A. Cummings

"Glencore’s Sudbury Integrated Nickel Operations in Falconbridge, Ontario, has been in operation since 1930. Many new technologies and practices, now common in the industry, have been implemented at the site and contribute significantly to the industry’s understanding. Since the last update on the Smelter operation published at the NiCo 2005 conference, the Converter Aisle has undergone significant changes in the operation of vessels. The Aisle continues to consist of 4 Peirce-Smith converters, but the Slag-Make Converter, and the Slag Cleaning Vessel have been re-tooled or re-built as Hybrid Vessels (HV), each generating matte for the two Finishing Converters and clean slag for disposal. The complicated scheduling and the overall benefits to the Smelter are reviewed here as part of the on-going tradition of industry support.INTRODUCTION The Glencore Nickel Sudbury Smelter operates a Roast Reduction Smelting (RRS) flow sheet with a specialized Converter Aisle operation that maximizes metal recovery to Bessemer matte. The main process equipment consists of a pair of Fluid Bed Roasters, a submerged-arc Electric Furnace and four Peirce-Smith converting type vessels (Figure 1). In the RRS flow sheet, concentrate is roasted with air to remove sulphur as SO2. Calcine from the Roasters is mixed with petroleum coke upon addition to the six-in-line rectangular Electric Furnace. The coke back reduces the metallic oxides, producing a matte and a discard slag.Gases from the Roasters are sent to a single pass absorption Acid Plant where the SO2 is converted to acid. Under the previous operating targets, approximately 70–75% of the sulphur in the incoming concentrate was fixed as acid with the balance going to the Electric Furnace in calcine for Bessemer matte production. Off-gases from the Electric Furnace and Converters are combined in a balloon flue, treated for particulates in electrostatic precipitators and discharged to the Smelter stack without any SO2 fixation."

Jan 1, 2017

By CIMVAL

This Code for the Valuation of Mineral Properties (the “CIMVAL Code”) is the result of a review more than a decade after the release in 2003 of the “Standards and Guidelines for Valuation of Mineral Properties” (the "2003 Standards"). The purpose of the review is to update the 2003 Standards to reflect domestic valuation, international valuation, and regulatory developments. The CIMVAL Code was adopted by the Canadian Institute of Mining, Metallurgy & Petroleum (the "CIM") Council on November 29, 2019. The CIMVAL Code supersedes the 2003 Standards. The 2003 Standards were dated February 2003 and were adopted by the CIM Council on March 9, 2003 as the first comprehensive set of standards for Valuation of Mineral Properties in the Canadian mining industry. The 2003 Standards followed recommendations of the Mining Standards Task Force of the Toronto Stock Exchange and the Ontario Securities Commission, where in its Final Report (January 1999), the CIM was specifically asked to form a committee of valuation practitioners to review and advise on standards for the Valuation of Mineral Properties. The Special Committee on Valuation of Mineral Properties ("CIMVAL") was created on May 5, 1999 with the mandate to recommend standards and guidelines for Valuation of Mineral Properties to be used by the mining industry in general. The CIMVAL Code is limited to the Valuation of Mineral Properties (including any interests therein) and does not cover valuation of corporations or other entities that hold Mineral Properties as assets. The CIMVAL Code does not cover petroleum and related assets. CIMVAL recommends that the CIMVAL Code be followed for all Valuations of Mineral Properties, including those required by securities administrators and stock exchanges. However, when a Valuation is required under the applicable rules of securities administrators or stock exchanges, such rules prevail to the extent of any inconsistency.

Nov 29, 2019

By Hans E. Madeisky, Bruce W. Downing

The acid rock drainage (ARD) buffering capacity of mine waste is governed by its bulk chemical composition and its mineral assemblage. Conventional acid base accounting (ABA) tests can be used to predict short-term buffering, but should be used with caution to model or predict the long-term ARD buffering capacity of mine waste. ABA data for mine waste samples from four different deposit types: an orthosite-hosted magmatic sul?de nickel, dunite-hosted magmatic sul?denickel, porphyry copper-gold, and volcanic-hosted high sul?dation epithermal silver, were compared with whole-rock geochemical and petrographic data obtained from the same samples. Our objective was to devise and test a method of predicting ARD buffering capacity based on bulk chemistry and modal mineralogy. In other words, we developed a quantitative theoretical method for calculating neutralizing potential, relying on easily obtainable and relatively inexpensive whole-rock and sulfur XRF analyses, which could substitute for conventional ABA procedures in situations where these procedures are either too costly or too time consuming. For each deposit type, models were devised that reasonably approximate the net neutralization potential estimated by the ABA data obtained from laboratory tests. Once an appropriate model has been developed and tested, portable X-ray ?uorescence equipment, already used for grade control at many mine sites, could provide the whole-rock and sulfur analyses required to estimate the ARD potential of the waste material. Although this approach is not intended as a substitute for the legally mandated ABA test procedure, it could facilitate the timely and cost-effective management and mitigation of ARD at a mine site.

Jan 1, 1997

By T. Prietl

Metallurgical vessel linings are multilayered, consisting of refractory bodies, insulation materials, joints, and additional space to control for thermal expansion. A unique biaxial hot testing press (BHTP) was installed at the RHI Refractories Technology Center Leoben, Austria to enable the three-dimensional behaviour of complex vessel lining segments to be investigated under simulated service conditions. Using the BHTP, the heat up and thermo-mechanical behaviour of magnesia chromite brick lining segments with and without mortar filled joints were examined. The results obtained during the initial heat up provided validation of CFD modelling of the lining system. In addition, after the heat up and under steady state conditions, the lining behaviour during deformation-controlled compression and relaxation was examined. These analyses generated important data regarding the stiffness, joint compressibility, and brick damage of the lining segments after cyclic loading and unloading as well as the benefits of using mortar joints in the lining. These investigations were performed in collaboration with the Christian Doppler Laboratory for Secondary Metallurgy of Nonferrous Metals, University of Leoben, Austria. The BHTP has been operational since November 2004 and is providing information regarding the thermo-mechanical behaviour of different lining segments.

Jan 1, 2007

By H. A. Gorrell, S. R. L. Harding

"The potash beds in the Saskatchewan portion of the Williston Basin occur in the upper portion of the Prairie Evaporite formation of the Devonian Elk Point Group. They represent the late stage of a major evaporitic cycle. Two other evaporitic cycles are known in overlying beds, but these apparently never reached the stage of potash salt deposition. The basin in which salt deposition took place extended from the northwestern corner of Alberta southeastward across Saskatchewan into Manitoba, North Dakota and Montana. Deposition of potash salts was apparently restricted to the southeastern portion of the evaporite basin. On a regional basis, five major stratigraphie divisions of the potash-bearing strata have been made. Locally, several of these units may be divided into correlatable sub-units. The potash-bearing strata are separated and overlain by predominantly halite layers of varying thickness. Cross sections show the regional correlation of the potash-rich zones, and maps show the present distribution of the individual potash-bearing zones and the areas of richer development for each zone. The maps tend to substantiate the interpretation of considerable subsurface solution of salt and potash beds."

Jan 1, 1967

By Greg Yuriy

Over the past two decades, Vale Canada has used discrete-event simulation in a key role to support many underground mining studies. Traditionally, general purpose simulation software was developed for manufacturing and service applications. Not until recently have Mine Designers and Simulation Specialists been able to model the dynamics of underground mining scenarios without extensive manipulation of the inherent tools and entities contained within these simulation environments. This paper discusses Vale Canada?s past experiences with a variety of simulation software, describing model development methods and highlighting some of the lessons learned. The paper concludes with a review of recently considered software and provides a framework of desired attributes/functions for modeling mining scenarios.

Aug 1, 2013

By W. K. A. Congreve

Introduction Less than a hundred years ago the engineer was able to do his job without concern for the science that underlay his practices or for the men who operated his machines. But toward the end of the last century science began to be applied to industry, and its success was such that the plant which clung to empiricism was unable to compete with the plant that followed science. Even more recently, the engineer has been forced to consider the men who operate his machines, for modern large-scale industry has given these men education, social security, and power. Hence the engineer can get good, steady labour to operate his machines only if he can offer inducements. Wages are in general outside the control of the engineer, but he is able to control working conditions. This essay is concerned with one factor of good working conditions: safety. The writer became interested in this problem during three months' summer employment as a student at the Sullivan concentrator of the Consolidated Mining and Smelting Company and was surprised at the distance his investigations led him from the field of pure engineering into the fields of psychology, education, and publicity. Nevertheless, because safety has to do with machines and with men who operate machines, and because it profoundly affects plant efficiency, it is the job of an engineer, not of a psychologist or teacher, nor of the salesman publicity expert who is often so unfortunately employed in personnel relations. The size and complexity of the subject has limited the scope of this essay to the consideration of only a few aspects of industrial safety. Considerable attention has been given to the underlying principles, but the mechanical side of accident prevention, the design of equipment, erection of guards, etc., and the very important problems of organization and administration, have not been given attention proportionate to their importance.

Jan 1, 1948

By S. Constantinides

"A major use for many of the rare earths is in permanent magnets. While alternate technologies are in research or already exist, rare earth magnets are unlikely to be supplanted as a major input to clean technologies and high efficiency consumer and industrial devices. We’ll examine where and how the magnet rare earths are utilized and the size of the market. Market growth forecasts based on global markets will be presented. A brief explanation of materials research in the US completes the material.INTRODUCTIONRare earth magnets, first commercialized c.1969, have become essential for a wide range of consumer, industrial and military devices. They are used in the speakers and vibrator motors of cell phones. Rare earth magnets spin the hard discs within the drives and rare earth magnet voice coil motors position the read/write head over the spinning platter. Rare earth magnets are the heart of motors and generators used on airplanes – they are smaller and lighter weight than alternative materials/devices. Now rare earth permanent magnets are being introduced into electric vehicles and wind power generation.Rare earth minerals are difficult to extract from the ores and to separate from one another. The increase in use of rare earth magnets has placed a severe strain on established sources of supply. The establishment of new mines and processing facilities is costly and requires upwards of 15 years to become productive. The combination of rapid rise in use of rare earth minerals coupled with supply shortages has caused rapid price increases and threat of non-delivery of product. The result of this disruptive situation has been a profound response at several levels: corporate, industry-wide and governmental. Let’s learn more about why rare earth magnets are so important to modern society."

Jan 1, 2012

By F. E. Patton

"IntroductionAT NORANDA, the strength of the ore and wall-rocks per-mitted mining in large open stopes. While some of the orebodies were small and could be mined out in one stope, in most cases their size was such that it was essential that ore pillars be left during the first stage of mining. In these cases, backfilling has been necessary for ground control and to facilitate the later recovery of the ore in these pillars.This paper discusses the development of the •backfill and •its use in pillar recovery.GeologyThe ore bodies at Noranda occur as replacement deposits in a block of rhyolite flows and breccias, bounded on the north by the Horne Creek fault and on the south by the Noranda Andesite fault. Mineralization consists of pyrite, pyrrhotite, magnetite, chalcopyrite, sphalerite, gold, and various tellurides.The main orebody is a massive sulphide deposit designated the 'H' orebody. It is elliptical in plan, measuring roughly 400 feet by 800 feet, and is divided into two zones -Upper H, extending from surface to the 1,500-foot level, and Lower H, from the 1 ,500-foot level to just below the 3,000-foot level.Mining MethodsOpen stope mining in both Upper H and Lower H zones has been fully described in previous publications (1). A brief review only of the mining methods will be given here."

Jan 1, 1952

By Jiuhua Xu, Shuiku Jia, Weiren Sun

"Abstract -The Jinqingding gold deposit, situated in the east Jiaodong Peninsula of Shandong province, is typical of the pyrite-quartz vein gold deposits in the Muping-Rushan gold belt of China . The gold deposit is controlled by a great NNE fracture zone and is composed of several lenticular orebodies within the fracture zone occurring in the Kunyushan granite massif. The Kunyushan granite massif was formed by the replacement of the Archean Jiaodong group.The main minerals associated with gold are pyrite, chalcopyrite, galena and sphalerite; the gangue minerals are dominated by quartz, sericite, microcline and calcite. The mineralizing event can be divided into four stages: (1) pyrite-quartz; (2) quartz-pyrite; (3) siderite-polymetallic sulfides; and (4) calcite-quartz. Gold occurs mainly as native gold and electrum in stage 1 and stage II. There are some evident differences between pyrite from major stages of gold mineralization and that from minor stages; these include differences in crystal forms, size and composition of fluid inclusions.Wallrock alterations consist of sericitization, silicification, pyritization and potash-feldspar alteration. Five alteration zones can be distinguished from unaltered granite (zone 0) to vein lodes (zone IV). Au and Ag increase rapidly from zone 0 to zone IV, Cu increases continuously, while Pb and Zn increase slowly. R-type geological factor analysis indicates that the Au, Ag, Cu, Pb and Zn bear a close relationship to wallrock alteration."

Jan 1, 1994

By Edward S. Bell, Frank Angebrandt

"Nuclear reactors must have very large heat outputs to compete with conventional sources and the only feasible applications are in the production of electric power or large quantities of process steam. This paper considers alternative fuels for electric power generation in Canada. In a publicly owned utility, nuclear stations are economic for base-load generation for unit sizes of 500 mega• watts or larger where competitive fossil fuel costs are higher than about 30 cents per million Btu. In British Columbia, Alberta and Saskatchewan, fossil fuels will continue to be in adequate supply at costs lower than 30 cents per million Btu and thus, except for the special case of Vancouver Island, power generation in Western Canada will continue to be the hydraulic and conventional thermal type. In Eastern Canada, fossil fuel prices are likely to be higher than 30 cents per million Btu and most utilities will be able to install units of 500 mw or larger, so that nuclear power plants will provide much of the base-load generation required. Base-load generation comprises about two-thirds of the energy generated by power utilities. By 1990, the total annual electrical energy load will be over 600 billion kwh, with two-thirds of this load in Eastern Canada. Allowing for additional hydraulic resources which may be developed in Quebec, British Columbia and Manitoba, hydraulic generation is forecast to provide a little more than a third of this electrical energy, nuclear generation a third and fossil-fuelled generation about a quarter."

Jan 1, 1969

By C. Nikolic

A process utilizing ozone for the precipitation of cobalt from nickel sulphate liquors containing ammonium sulphate has been developed. Best results were obtained using nickel carbonate to maintain solution pH at 5.0 to 5.5. Work was performed both in column and stirred-tank reactors. Variables studied included neutralizer type and concentration, NH4+ concentration, temperature, Ni++ and Co++ concentration, per cent O3 in the O2 carrier gas, O3 input rate and agitation. The over-all rate of cobalt rejection increased sharply with increasing agitation and ozone concentration in the gas phase, reflecting relatively slow transfer of ozone from the gas to the liquid phase.

Jan 1, 1978

By A. E. M. Warner, I. E. Hills, C. L. Harris

Since the late Dr. Keith Brimacombe, et al, performed tests at the now-closed Asarco Tacoma smelter and the Inco Copper Cliff Smelter on Peirce-Smith copper converters almost thirty years ago, many Pyro-metallurgists have investigated using the technology. To the best of the authors knowledge, except for shrouded tuyere technologies using substantial oxygen enrichments, the core idea of using high pressure air injection has not been implemented anywhere in the world. This paper reviews the fundamentals of this technology and summarizes the basic economic considerations. It also presents the circumstances of where and when high-pressure injection might be justified.

Jan 1, 2007

By J. E. Nesset

Significant progress has been made over the past few years on characterizing and understanding the hydrodynamic properties of frothers and collectors and their effect on flotation performance. This new understanding of the relationship between chemistry and hydrodynamics has dramatic implications for how flotation circuits should be controlled and optimized. Previous work has shown that choosing a frother of the right 'strength' is critical to the optimization process, and the work and discussion presented here serve to strengthen the argument. In addition, we know that collector chemistry may also influence hydrodynamic properties and needs to be taken into consideration. To achieve the desired outcome, the overall system of reagents and operating parameters must be considered. This paper describes and discusses some of the findings from recent research on frother and collector chemistry effects (on hydrodynamics), and how this knowledge can be used to improve flotation performance. Examples from plant experience are discussed.

Jan 1, 2009

By B. Calver, D. J. M. Farnsworth

"As open-pit operations expanded at Pine Point, hydraulic aquifer evaluation was undertaken to establish the criteria necessary for the design of a feasible dewatering system.The extreme climate of this northern location dictated that the ore zone under extraction be rendered as dry as possible to minimize freezing effects. The design and implementation of such a system necessitated detailed hydraulic evaluation, and the problems that occurred are typical of those inherent in open-pit mining operations in northern areas.The paper describes the problem solution as approached from a mine engineering point of view, with particular reference to the practical aspects of operation and installation. The hydrological analysis used is simple and readily applicable to most open-pit dewatering problems."

Jan 1, 1969

By C. R. Whittemore

Introduction The technical library in the service of industry is gradually becoming a well recognized and important part of all progressive industrial organizations. The larger mining, metallurgical, and chemical firms of Canada are establishing extensive reference libraries in connection with their research and operating departments in order that the members of the organization may keep abreast of the rapidly developing fields of engineering in which they are interested. It is the purpose of this paper to point out the usefulness of such a department in any industrial organization, to give a general outline of a system for filing and dispensing information, and to outline briefly the literature to be consulted and the procedure to be adopted in instigating a literature search. The technical library falls under the classification known as 'Special Libraries', and is quite different from the general library in that it is a storehouse of facts and owes its value to the ready presentation of information required for each specific case, and in a form most ready for use. The library brings all the available information relative to the interests of the corporation from without the plant to the organization within, and also keep in touch with each department of the organization.

Jan 1, 1930

By R. A. Wyman, F. E. Hanes

THE demand for high-quality aggregate is increasing in all phases of the construction industry and in all organizations associated with road building in Canada. The production of aggregate in Canada has increased almost continuously since the end of the war and has quadrupled since 1948. Increases during the past fifteen years can be accounted for by the expansion in all types of construction, particularly that of roads and highways. Total construction in 1959, based on preliminary estimates, has been valued at $7 billion, and an increase fore-cast for 1960 indicates optimism on the •construction horizon (1). Cement produced in Canada in 1959 amounted to 6.3 million tons. This is more than 2.5 times the 1948 production. Increased cement production indicates an increased use of concrete, and thus an increased need for aggregate. Natural sand and gravel deposits are gradually being depleted.

Jan 1, 1962

By O. W. Borgeson, D. K. Honsberger, R. T. Bell

The Scully Mine, situated in the Labrador Trough near the Quebec-Labrador boundary, is one of the world's largest continuous ore deposits. This paper outlines the sequence of the mining operations from the planning stages to the delivery of the ore to the crusher at an average rate of 50,000 tons per day, 7 days per week. The principal equipment required to maintain this production rate includes four 12.\1.1-inch rotary drills, seven 8-cu.-yd electric shovels and a fleet of large haulage trucks. Particular attention is given to grade control, programmed by computer, drilling and blasting techniques and operational aspects inherent with open-pit mining in Canada's North.

Jan 1, 1969