Search Documents

By Pierre Lacoste-Bouchet, Ian Orford, Mike Cooper

"The Brunswick Mine ore requires fine grinding to achieve liberation of minerals. With 25mm slugs as the grinding media in the ball mill, there was a limitation of a P80 of 25 microns on the CuPb regrind circuit. Results from pilot plant testing showed that the separation efficiency could be increased through fine grinding with a P80 of 15 microns.Options considered were the capital expenditure for new fine grinding equipment such as a vertimill or the use of the present ball mill equipment with smaller media. The Wheelabrator Allevard Enterprise (WAE) millpebs product was chosen because it was a smaller media with a distribution of steel pellets between 5 to 12 mm.With millpebs the grinding product was reduced in size from a P80 of 25 microns to a P80 of less than 19 microns. The power draw to achieve the finer grind was 13% lower while the media consumption was 57% higher.The millpebs grinding media was also tested on the zinc regrind mill. The purpose of the trial was to understand what the media consumption and power draw would be with the charge lowered to achieve an equivalent grind as obtained with the slugs. The media consumption was approximately the same and the power draw was reduced by 30%.INTRODUCTIONThe Brunswick Mine ore is a complex Pb-Zn-Cu-Ag sulphide ore with the grain size of the minerals varying from submicron blebs to particles up to several mm in size. The ore is ground progressively finer in stages. The first step of grinding occurs in the SAG mill circuit. The product sizing 80% passing 95 microns is fed to the CuPb prefloat stage (Cormier et al 2002). The tails from the prefloat is then further ground to a P80 of 35 microns for the CuPb rougher flotation. The final liberation for the CuPb circuit takes place in the CuPb regrind circuit. The regrinding mill further liberates the cleaner scavenger concentrate, second cleaner tails and third cleaner tails. The reasoning for the progressive grinding is to achieve fine grinding without having galena over ground due to its high specific gravity that preferentially sends it to the cyclone underflow."

Jan 1, 2006

By K. Duckworth

"Comparative tests of the conventional Turam survey configuration and an alternative configuration called the Tx-parallel configuration were conducted at the McClean uranium deposit in northern Saskatchewan. Both configurations detected the known conductors at the site but the alternative configuration demonstrated its particular effectiveness in the reconnaissance role. This effectiveness results from the fact that the length of Tx-parallel traversesis controlled only by the length ofthe transmitter and not by its power. In addition, the field strength along a Tx-parallel traverse is uniform unless the traverse approaches the end of the transmitter. This freedom from a strong gradient of the primary field along a Tx-parallel traverse eliminates the gradient-induced anomaly shifts which are common in conventional Turam operations. The locations of each of the McClean conductors, that were obtained from the Tx-parallel profiles, werein better agreement with the locations known from drilling than were the locations obtained from the conventional profiles. However, the conventional profiles gave better estimates of the conductance of the targets.The results obtained over the McClean conductors indicate that current gathering has a strong influence on Tx-parallel results with consequent unpredictable influence on depth and conductance estimates. However, the depth estimates obtained from the Tx-parallel data appear to be in good agreement with the known depth of the McClean south conductor. The Txparallel results provide shallow estimates of the depth of the McClean north conductor which suggest that the fracture zone above the graphitic conductor is a significant conductor as was also suggested by earlier VLF surveys.Comparison with the wide range of published geophysical test surveys for the McClean site showed that apart from the work required to lay the transmitter, the Tx-parallel mode of operation of a Turam exploration system is operationally very similar to a moving source Slingram type of survey. At the McClean test site, it provided the same depth of exploration as a conventionally deployed fixed loop transmitter."

Jan 1, 1988

By C. O’Hara, S. Roy, K. Swedburg, J. Katchen

"New Gold Inc.’s New Afton concentrator commenced operation in June 2012, producing a copper-gold-silver concentrate. During the first two years of operation, various optimization efforts have improved mill throughput, recoveries and concentrate grade. Daily mill throughput has increased 20% above the design rate. This was achieved through more consistent instantaneous feed rate and size distribution from the mine reclaim stockpile, higher pebble crusher reliability, changes to the SAG and ball mill grinding media sizes, larger SAG grate openings, reduced SAG discharge screen-deck aperture size and an increase in the maximum ball mill power draw limit. Metal recoveries at New Afton are primarily limited by liberation in the coarser size fractions; therefore, improving the grind size at a given mill throughput has been the main means of improving recovery. The average rougher flotation feed F80 size was reduced from 175µm in Q1 2013 to 165µm in Q1 2014, while the average operating mill throughput increased by 25%. Other flotation circuit changes focusing on recovery improvement include the addition of froth crowders to the rougher cells and the use of a stronger frother. The average concentrate grade increased from 22% Cu in Q1 2013 to 25% Cu in Q1 2014. This was achieved by redirecting the flash flotation concentrate stream to the regrind circuit and by the addition of lime to the cleaner circuit.This paper describes the above improvements made at the New Afton mill. The paper describes the objectives, timing and end result of each area of improvement.IntroductionThe New Afton Mine is situated approximately 10km west of Kamloops, British Columbia, 340km north-east of Vancouver. The mine has a moderate climate, access to transportation and electrical infrastructure, nearby fresh water supply, and close proximity to industrial and mining service businesses. The population of Kamloops is around 90,000 with most mine employees living in or around the city."

Jan 1, 2015

By C. F. Gleeson, D. G. Sheehan

"The results of humus and overburden geochemical surveys over the Doyon, Bousquet and Page-Williams gold ore deposits are presented.These studies show that humus sampling for gold gives negative results over the Doyon deposit. The lack of response is probably caused by the presence of 1 m of relatively impermeable glaciolacustrine clay and silt that overlies 1 m to 2 m of till over the surface expression of the ore zone. By contrast, positive responses for gold occur in humus samples over the Page Williams A and C gold deposits. The ""A"" ore zone is covered by several metres of exotic calcareous till over 0.5 m to 1 m of older, locally derived till. Anomalous values for gold in humus range from 10 to 35 ppb over the orebody. Overburden over the ""C"" ore zones is much thinner, generally it consists of less than 2 m of sandy till. Trenching humus anomalies that range from 10 to 1360ppb Au uncovered the gold mineralization. The geochemical dispersal trains in till from the Doyon orebody and the Page-Williams ""A"" zone are relatively short (i.e. less than 200 m) because both deposits occur in the lee of bedrock highs that shielded them from extensive glacial quarrying. Dispersal trains from all three pyritic gold deposits can be defined using either the fine fraction or heavy mineral fraction of the till.The intensity of the gold in till anomalies over the ore zones is variable. Therefore, it would be misleading to attach rigid significant threshold gold values to overburden drilling results. Each case must be evaluated based on bedrock topography, sample density, overburden type, thickness of till, as well as size, type and orientation of the target exposed to glacial erosion."

Jan 1, 1987

By James R. Lang

The Xietongmen deposit is located 350 km west of Lhasa, Tibet. It is a new, high-grade porphyry copper-gold discovery and the first deposit to be systematically explored by a western company in southern Tibet. In 2005, Continental Minerals Corporation drilled 21,332 m of core in 63 holes and demonstrated excellent lateral and vertical continuity of high-grade copper-gold mineralization over an area 750 m by up to 350 m in size which remains open in all lateral directions. Drill intersections repeatedly yield grades >1% Cu equivalent (based on gold and copper prices) and include 308.5 m at 0.87% Cu and 1.25 g/T Au (1.60 CuEQ%), and 315.6 metres at 0.61% Cu and 1.11 g/T Au (1.26 CuEQ%). Extensive drilling in 2006 will expand and delineate the deposit, and metallurgical, engineering, environmental and socio-economic evaluations will begin. Xietongmen is hosted by volcanic and intrusive rocks of the Gangdese belt, a magmatic arc active between 120 and 30 Ma along the southern margin of Eurasia. Pervasive alteration is dominated by a well-mineralized K-feldspar and biotite assemblage, and by a more peripheral sericitic assemblage also with strong chalcopyrite. Major vein stages include chalcopyrite-bearing quartz, biotite, magnetite and pyrite-pyrrhotite types.

May 1, 2006

By G. P. Holmes

"IntroductionThe copper-molybdenum property of Brenda Mines Ltd. is located 18 miles north west of Peachland in the Okanagan Valley of the Southern Central interior of British Columbia. The actual site is 50 miles north of the international boundary and 150 air miles east of Vancouver at an elevation of 5000 feet above sea level. The earliest written mention of the prospect is found in the Geological Survey of Canada, Memoir No. 243, issued in 1947 by Dr. H.M.A. Rice. In 1954 the area was staked by a prospector, Bob Bechtel, who interested Bern Brynelsen of Noranda Exploration in examining the claims. A joint Noranda - Kennecott program resulted but since the grades were so low the property was not taken up until in 1964 a re-examination by Chapman, Wood and Griswold produced recommendations leading to the construction of the Brenda Mine as it is today.The rounded, timber covered mountains of the area are composed of the tuffs, argillites and limestones of the Upper Triassic Nicola Group, which is intruded by a Jurassic quartz diorite, called the Brenda stock0 The actual orebody occurs in a strongly fractured zone within the Brenda stock, approximately 1500 feet from the contact with the Nicola group0 The ore minerals, .chalcopyrite and molybdenite, associated with pyrite and magnetite of lesser importance, occur as fillings within the fractures 0 The grade of the ore decreases outwards from a central higher grade core and in January 1971 total reserves were estimated at 165 million tons assaying 0,182% Copper and 0,049% Mo."

Jan 1, 1972

By G. Thom, A. Kay, J. B. Hyde

"This paper will initially outline the specific types of copper castings used in blast furnace iron production. Tuyeres, tuyere coolers and stack cooling plates will be discussed in some depth, with particular reference to their dimensional configuration and purpose.Following this, the failure of such cooling members will be discussed, with special focus on tuyeres. Tuyeres are the most common casting which often requires replacement. Reasons for failure and its effect on operations will also be included.The latter sections of the paper will deal with the strict specifications demanded by ironmakers regarding copper castings. The justification for such rigid demands will be explained through the material presented earlier in the paper.IntroductionThe modern 5000-tpd blast furnace, worth millions, is a large capital investment to be sitting idle. Consequently, ironmakers strive to minimize the loss in iron production and revenue from furnace downtime. Two major causes of downtime are furnace relines and shutdowns to replace damaged tuyeresor tuyere coolers. Copper ancillaries are important items in the production of iron. They are consumable items, therefore they contribute to the campaign life or to the downtime in blast furnace production.Several combinations of lining and cooling systems have been used with varying degrees of success. Blast furnace refractories have evolved from ceramic to carbonaceous linings. The Russians and Japanese have successfully introduced stave-cooled furnaces that may have several forms, such as evaporative cooling. Stelco has two furnaces which use the Russian-designed cast iron system. However, this paper will be confined to the use of copper cast cooling members in a conventional internally cooled furnace.Figure 1 is a schematic cross section of the E blast furnace. The three major sections of a blast furnace-the stack, bosh and hearth-are identified. Further, the locations of the various copper members are indicated. This furnace produces an average of 5300 tons of hot metal per day."

Jan 1, 1982

By J. G. Price

"The paper reviews state-of-the art welding processes and consumables for structural and pressure equipment applications in offshore environments, particularly the Arctic. Optimum selection of consumables will be discussed with regard to the facility to meet tentative toughness requirements in weldments. Finally, the development of welding procedure specifications will be considered in relation to the prevention of hot or cold cracking and lamellar tearing.Welding RequirementsGeneralThe exploitation of Canadian frontier oil and gas reserves will require a fleet of various types of offshore structures. These will include fixed jacket types and semi-submersibles for the East Coast with huge man-made islands and icebreakers for the Arctic regions. Both these regions will also require supply and drill ships plus subsea pipelines and cargo tankers for transportation. Clearly the welding of these items will plays large part in the over-all integrity and safety of exploration and production operations.The required development in structural steels and pressure vessel steels, for current and future offshore structures, to improve properties, particularly toughness for lower temperature service, has also prompted welding researchers to develop process and consumable combinations to match the parent plate specifications. This development has had to consider particular aspects of weldability such as a low susceptibility to cold cracking and preventing low HAZ toughness. Current research has centred on attempts to increase HAZ toughness with higher heat input welding of newly developed structural steels.The installation of Arctic region pipelines has provided a sound base for future, more complex fabrications in the most severe service temperatures in the Canadian frontier although few of the installations have been designed to the lowest possible exposed temperature of -62°C."

Jan 1, 1987

By F. Ford, J. Dong

"Laboratory and miniplant testwork was carried out to reject uranium from an Iron Oxide Copper Gold (IOCG) deposit that contains an average of 60-70 ppm uranium with high variability. The dominate copper bearing mineral is chalcopyrite with minor bornite and trace covellite. The main gangue minerals are iron-rich chlorite, quartz and magnetite. The main uranium-containing mineral is uraninite (UO2). Downstream processes require the maximum uranium level of no more than 80 ppm in final copper concentrate.Mineralogical examination reveals that uraninite particles are finely disseminated with grain size of less than a few microns in the deposit requiring fine regrind in order to liberate uraninite from chalcopyrite particles. A lab flowsheet was developed to include ultrafine regrind of the rougher concentrate to the particle size of 80% passing 11-13 µm with up to four stages of recleaning in flotation columns. Finer regrind to 80% passing 5-6 µm may continue to improve liberation but does not decrease uranium level in the final concentrate. In each of the successive recleaning stages by flotation column after fine regrind, uraninite is rejected into the column tailings, with the final copper gold concentrate containing less than 70 ppm uranium from a feed containing 83 ppm uranium. The conceptual flowsheet was further tested in an integrated, continuous miniplant showing average 94% copper recovery with average 74 ppm uranium. The uraninite particles that report to the final concentrate are either locked with chalcopyrite or entrained as liberated particles of less than 5 µm in size.IntroductionIron Oxide Copper Gold (IOCG) deposits are copper and gold ores hosted within a large body of iron oxide and are significant ore deposits for copper and gold (Williams, et al., 2005). These deposits can also contain economic levels of other metals such as uranium and rare earth elements. The known sizes of IOCG deposits range from 10 to 4,000 million tonnes with grade of 0.2-5% copper and 0.1-3 g/t gold. One of the greatest IOCG deposits is Olympic Dam in South Australia. It is the fourth largest copper deposit and the largest uranium deposit in the world. Gold and silver in the deposit also contribute significantly to the total revenue."

Jan 1, 2017

By Paul Gauthier

Aujourd?hui, avec un faible prix de l?or sur le marché, les opérateurs miniers doivent revoir leur façon de faire. La méthode de minage «Eureka» permet de réduire les coûts de production et d?accélérer la mise en production des chantiers. Les principales étapes du cycle de minage et les problématiques associées à l?utilisation de cette méthode à la Mine Bousquet y sont décrites.

Oct 1, 2001

By B. Jago

From the perspective of metallurgical processing, gold ores can be classified into freemilling and refractory ores. Their extractive metallurgy is largely driven by mineralogical factors such as gold particle size, association with other minerals, coatings and rimmings, presence of cyanicides, oxygen consumers and preg-robbers, presence of refractory gold minerals, and invisible gold in sulphide and sulpharsenide minerals. Gold process mineralogy helps address issues and problems related to gold ore processing. It is widely used as a predictive and trouble-shooting tool in gold ore processing, and provides useful information on process selection, flowsheet development, recovery improvement, and reagent consumption optimization. By combining classic mineralogical techniques, modern instrumental analysis, and diagnostic metallurgy, the mineralogist is able to balance the various types of gold occurrence in an ore.

Jan 1, 2006

By R. J. Balfour, T. L. Papucciyan

"INTRODUCTIONCapital Cost considerations are basic to feasibility in the achievement of success for Mineral Processing Projects as much as or more than in many other industries. Capital cost is an important factor ae it 1R the unit of measurement for process engineering economic decisions. As a result of ever increasing complexity, alternatives of process and remoteness of site, there is an ever increasing emphasis on accurate estimating and the attendant cost control systems in the international market of today for the Mineral Industry where initial plant costs are becoming a more important factor than operating costs. An undervaluation means trouble ahead. An over-cautious assessment may bring an unnecessary abandonment of a project. Consequently, the ultimate cost must be predicted early and accurately and must be controlled to this parameter during the design and construction phases. Cost Est!~ mating is one of a variety of project management tools used to assist in planning and achieving the optimum balance between Quality, Cost and Time, the eternal triangle of evaluation, namely obtaining a project of acceptable quality at minimum cost and on time. In order to attain these established objectives, proper planning, organizing, coordinating, monitoring, adjusting and controlling the design, procurement and construction elements of the project are essential.This project management approach based upon the principle of a Task Force under single management, comprising a complete service organization, requires a substantial number of qualified individuals specialized in their own field and capable of working together as a team to perform their various functions effectively. The Task Force is supported by their chiefs of discipline and performs in accordance with established procedures and standards under the leadership of a Project Manager.General Engineering Company Limited with the backing of the full resources of Surveyer, Nenniger & Chenevert and its total staff of approximately 1,0009 offers the complete project management service to the Mineral Processing Industry of North America and the rest of the world. As mine sites become more remote and difficult of access, the need for an experienced team of specialists who work under the Task Force principle, with well established standards and procedures becomes even more important. Our long history of successful pro1ecta in this field has been our training ground for the fulfillment of this need."

Jan 1, 1972

By H. J. McQueen

ORDER OF PRESENTATION ?INTRODUCTION TO THE VICTORIA BRIDGE ?REASONS FOR A BRIDGE AT MONTREAL ?RAILROAD BRIDGE REQUIREMENTS ?IRON PRODUCTION CANADA / WORLD AL ?METALLURGICAL INDUSTRY CANADA ?FAIRBAIRN, STEPHENSON SHIP PLATE-RIB BOX GIRDER ?VICTORIA BRIDGE (PREFABRICATED BRITAIN) ?IRON ORE SITUATION THE VICTORIA BRIDGE 1859, TUBULAR -WROUGHT IRON* 1898, TRUSS ?STEEL* (*HOT RIVETED) 1957, SPUR, LIFT SPANS ??DUCTILE WROUGHT IRON WITHSTANDS FATIGUE ?TO KEEP THE TRAINS ON TIME & ON TRACK? ??IMMOVABLE SHARP PIERS SPLIT ?THE IRRESISTIBLE ICE, STOPPED CITY FLOODS? ? ?********* ??111 YEARS-YOUNG STEEL TRUSS, (1898): ?STILL VITAL SEA-T0-SEA RAIL LINK? ? ?********* ??51 YEARS HAVE PASSED SINCE SEAWAY (1958) ?SWITCHED BRIDGE INTO DOUBLE LIFT SPANS?

May 1, 2011

By Brigitte J. Dejou

The Red Dog sediment-hosted zinc-lead deposit is located in the Brooks Range thrust belt in northwest Alaska, approximately 1000 km northwest of Anchorage. The mine constitutes the primary deposit in a 400 square kilometre district, which hosts several other mineral occurrences. All the known mineralisation is hosted by the Mississippian Ikalukrok Member, deep basinal shale of the Kuna Formation, part of a Devonian to Cretaceous sedimentary sequence. The rocks underwent intense deformation during the Brookian Orogeny in Middle Cretaceous time. Several thrust faults juxtapose the stratigraphy. The Red Dog mine is composed of four deposits which together contain 105 Mt in resources and reserves for a total resource exceeding 18 Mt of Zn metal. The mine is an open pit with 25 foot high benches. The biggest challenge is not the Arctic conditions, but metal extraction, due to the fine grained nature of the mineralisation and the variability of the ore. The mine produces Zn and Pb-Ag concentrates that are shipped to smelters around the world from the Red Dog port facilities during the short summer period. Ore mineralogy is generally simple and consists of sphalerite, pyrite, galena and marcasite. The deposits are generally overlain by decametre thick exhalative barite horizons and exhibit strong silicification, which locally obliterates the original textures. Although described as a world class Sedex-type deposit, a large portion of the mineralisation exhibits sub-surface replacement textures. Moreover, unlike most other Sedex deposits, the reconstruction of the basin is made difficult by the structural complexity of the district. To assist exploration in the district, several assumptions are made regarding the deposit settings relative to metal source, growth faults or crustal extension.

May 1, 2006

By R Thomson

The use of uranium metal in non-ferrous metallurgical practice is dis-cussed with reference to its alloying behaviour and chemical activity. It is suggested that the more promising applications are in the treatment of molten metals to combine with impurities. Mines Branch work along these lines is described for copper, zinc, magnesium, aluminum and nickel alloys. It is shown that a cop-per-uranium master alloy (25 per cent U) successfully deoxidizes molten copper without detriment to the electrical or mechanical properties of the product at residual uranium levels of up to 0.8 wt. per cent. Additions of uranium to alpha brass in amounts greater than the lead impurity content were found to remove the deleterious effect of lead on hot-workability. Similar deoxidizing and malleableizing effects were found with uranium additions to nickel. It is thought that uranium forms stable intermetallic compounds with many impurity elements. A significant malleableizing effect can therefore be expected in the presence of other elements besides lead.

Jan 1, 1963

By K. J. Fair, H. W. Smith, D. R. Francis, J. M. Toguri

"Bench-scale batch milling and screening tests were carried out on secondary aluminum dross 10 produce an aluminum concentrate. To complement these tests, an analysis of a commercial plant was also performed by sampling dross at various stages in the plant's milling and screening circuit. These studies have indicated that benefits of increased capacity, grade and recovery of aluminum metal can be realized by addition of screens before the ball mill, longer grinding period and by grinding the smaller size fractions more efficiently.To test the predictions, a plant test was performed on the milling of100tons of secondary dross. The recycling of the large size fraction (+1/8 in.) of aluminum dross through the impact mill rather than through the rate limiting ball mill resulted in a comparable aluminum grade. The ball milling of the _1/ 8 in. + 10 mesh size gave a dross grade of71% AI. A lower feed rate to the ball mill resulted in a higher final grade. With minor modifications, secondary dross can be processed in 22% of the time it takes with the present circuit without a sacrifice in grade.IntroductionSecondary aluminum dross is a mixture of metallic aluminum, aluminum oxides and salts (alkali halides). Any comminution process deforms or slowly grind s the malleable metal phase and reduces the size of the friable, brittle, oxide-salt phase relatively fasterr(1).The milling of aluminum dross is performed to upgrade the metallic aluminum fraction. Figure I shows a flowsheet for the milling of secondary dross as presently practised at Metals and Alloys Co. Ltd., Toronto, Ontario. At point A, large acceptable grade material is hand picked for refurnacing, the unacceptable off-grade material is sent to the sweat furnace and the remaining, + 2 in. fraction is recycled through the 3.9 ft by 4.1 ft impact mill. For simplification, three ball mills are shown. However, in reality there is only one, a 5 ft by 10 ft ball mill used in a semi-batch mode. The 2 in. + 3/8in. and 3/8 in. + 10 mesh products are remilled in the ball mill. The -10 mesh material is discarded as waste."

Jan 1, 1987

By E. Gallestey, D. Groenveld, F. Kolb, M. Rozou

"Recent copper price evolution pushes modern mining industry even harder to achieve highest production with maximum efficiency. Operations are bound by numerous contractual and environmental conditions that bring a high degree of complexity to both the operators controlling the process and the plant managers assessing the circuit’s potential and setting the production goals.Advanced process control (APC) for grinding is one important tool to operate this most energy intense area in an optimal way, finding the optimal trade-offs between highest throughput, energy efficiency and product quality based on variable ore properties, production targets and management priorities.ABB’s state of the art control and optimization software platform enables user to design a controller based on model predictive control (MPC). The paper and the presentation show the technology used and the results achieved through an APC controller installed in a pilot project in Aitik (Boliden SA), Sweden. Furthermore, possibilities to interconnect grinding with other areas as stockpile management and flotation with various interconnected APC controllers will be shown. Finally, an example of the return on investment and the payback times based on the increased throughput and better product quality will be presented.INTRODUCTIONDepending on the ore characteristics and the targeted plant capacity, the design of the grinding circuit may vary significantly. Typically, the circuit consists of several mills (rod, ball, SAG, AG) in series and/or parallel with a number of classifiers and sumps at appropriate locations (see Figure 1).The main goal of the grinding section is to reduce the ore particle size to a level that enables efficient separation between gangue and precious metals in the subsiding processing step. The trade-off between quality and quantity has to be made. At the same time, it is also crucial to execute this process at the lowest possible energy and grinding media consumption."

Jan 1, 2015

By G. M. Ritcey, K. E. Haque, S. H. Lucas

"Laboratory-scale hydrochloric acid leach tests were conducted on an Elliot Lake uranium ore. Hydrochloric acid leaches without an oxidant or with molecular oxygen (i.e., air or pure oxygen gas) as an oxidant favoured uranium and radium extractions. Conditions for maximum uranium, thorium and radium extractions with hydrochloric acid in the presence of sodium chlorate were determined. The highest extractions of uranium (96%), thorium (81%) and radium (91%) were obtained using a mixture of 44.0 kg HCI and 2.5 kg NaCIOJ per tonne of ore at 75°C with 18 hours ' retention.Flowsheets for two-stage leaching are proposed. The residues obtained from the second-stage leach contain uranium (0.002%), thorium (0.006%) and radium (15 to 20 pCi/g). Tailings of this nature are considered suitable for mine backfill, and, if pyrite is removed, suitable for surfacedisposal.IntroductionThe nuclear energy industry forecasts an increasing demand for uranium. This increasing demand requires not only largescale mining and processing of conventional and complex uranium ores, but also leads to the consideration of new and nonconventional sources of uranium, e.g., black shales, phosphate rocks, granite, sea water and fossil-fuel ash.Sulphuric acid leaching is the most widely used process to extract uranium from the ore(l). The leach liquor is separated from the solids (tailings), purified, concentrated in various intermediate stages, and finally a semi-purified product, yellow cake (80-85070 U30 8) , is precipitated. The tailings, which constitute nearly 98% of the total bulk of most ores, are usually discarded in surface disposal areas.The Elliot Lake region of Ontario is one of the major uranium producing areas in Canada. The principal uranium minerals are brannerite and uraninite, present as microscopic grains in the matrix of quartz-pebble conglomerates. The average grade is between 0.10 and 0.15% UPs. Up to 6.5% pyrite is also present in the conglomerates. Because pyrite is less reactive toward sulphuric acid leaching, almost all the pyrite goes into the tailings and eventually into' the disposal sites."

Jan 1, 1980

By G. M. Ritcey, K. E. Haque, S. H. Lucas

"Laboratory-scale hydrochloric acid leach tests were conducted on an Elliot Lake uranium ore. Hydrochloric acid leaches without an oxidant or with molecular oxygen (i.e., air or pure oxygen gas) as an oxidant favoured uranium and radium extractions. Conditions for maximum uranium, thorium and radium extractions with hydrochloric acid in the presence of sodium chlorate were determined. The highest extractions of uranium (96%), thorium (81%) and radium (91%) were obtained using a mixture of 44.0 kg HCI and 2.5 kg NaCIOJ per tonne of ore at 75°C with 18 hours ' retention.Flowsheets for two-stage leaching are proposed. The residues obtained from the second-stage leach contain uranium (0.002%), thorium (0.006%) and radium (15 to 20 pCi/g). Tailings of this nature are considered suitable for mine backfill, and, if pyrite is removed, suitable for surface disposal.IntroductionThe nuclear energy industry forecasts an increasing demand for uranium. This increasing demand requires not only largescale mining and processing of conventional and complex uranium ores, but also leads to the consideration of new and nonconventional sources of uranium, e.g., black shales, phosphate rocks, granite, sea water and fossil-fuel ash."

Jan 1, 1980

By Flavio Rojos-Tapia, Samuel Sánchez-Pino, Marcelo Fernández-García, Samuel Sánchez-Baquedano, Rainer M. Imhof

"Pneumatic flotation was introduced to the Chilean copper mining industry in 1993 by Ingeniería de Minerales S.A., being implementation in 1994/95. The technology is based on the designs and development of Dr. Rainer Imhof from Germany and from Chilean copper processing experience.Pneumatic flotation has been successfully used for sulphide and oxide copper minerals and copper slag, iron ores (reverse flotation), gold and promising results with molybdenum as product. Extremely hard conditions were applied in flotation process such as roughing, cleaning, scavenging. Pneumatic flotation can be applied for any type of mineral which has to be separated by flotation. Even very dense and heavy slurries can be processed, the range of the particle sizes to be collected is very wide, and the number of cleaning stages needed normally is one in our experience until now.The good performance of the technique can be explained by the high gas hold-up and the very effective micro-turbulences which boosts the attachment to the bubbles changing dramatically the flotation time concept. Some economic high lights are: less energy consumption, less maintenance costs, simple and reliable to operate and it is required a small area to install the circuits.As a result of the Chilean mining industry experience, it can be concluded that the pneumatic flotation can be regarded as an excellent alternative to the conventional way of Mineral Processing.INTRODUCTIONDerived from seventies, works in Germany about pneumatic flotation with Prof. Simonis (Technical University of Berlin) and Prof. Bahr (Technical University of Clausthal), it has been developed an interesting flotation technology in Mineral Processing, with the designs developed by Dr. Rainer Imhof, who has been known for more than ten years (Imhof, 1998) by his contribution at Ekof, KHD, Allmineral and the actual company Maelgwyn Mineral Services where he is a Technical Director. Ingeniería de Minerales S.A. has been working ten years deeply involved with the technology developed by Dr. Imhof and is more than ten years experienced with pneumatic flotation, from Wits University and Mintek in South Africa (Sánchez, 1990), (Sánchez, 1990)."

Jan 1, 2003