Search Documents

By S. Rajeswari, D. Gopi

"Pitting corrosion inhibition of 304 stainless steel (SS) in groundwater with a ternary inhibitor mixture (phosphonic acid + bivalent cation + various surfactants) was studied with different environmental variables such as temperature, pH, dissolved oxygen and chloride ions. Critical pitting potential and corrosion potential were calculated for these test media using electrochemical techniques. Under the tested condition, the localized corrosion resistance of 304 SS was determined and the results are discussed. IntroductionPitting corrosion of metals and alloys is a major cause of failure in chemical processing desalination plants, scrubber for flue gas desulphurization (FGD) plants, water storage tanks and pipelines, petroleum refineries, etc.Heat exchangers and condensers in inland thermal and nuclear powerplants utilize groundwater as a coolant, but materials of construction are generally prone to localized corrosion.Localized corrosion attack can be initiated when the passive film on the metal is disrupted. The presence of certain aggressive anions such as chlorides (Cl-) can migrate to the actively corroding area and stabilize pitting corrosion. Attention has been focussed on improving the resistance of stainless steel against localizedcorrosion in aqueous environments.One of the most accepted methods of avoiding corrosion is by the addition of chemicals (inhibitors). Over the past two decades, some phosphonic acids have been explored due to their good corrosion inhibition efficiency and low toxicity (Fang et al., 1993; Karman et al., 1998; Rajendran et al., 1998; Gopi and Rajeswari, 2000a). Bivalent cations like Zn2+ are often applied as additives to inhibit the metal dissolution (Sekine and Hirakawa, 1986; Aruna Bahadur, 1998)."

Jan 1, 2003

By Polysius AG

"The Lone Tree demonstration was an important milestone in bringing High Pressure Grinding Roll (HPGR) technology into hard rock applications in the mining industry. HPGRs have become standard equipment in the cement, iron ore, and diamond industries over the past fifteen years, but their use in severe duties found in the hard rock mining sector has been restricted due to high roll wear and subsequent low availability. HPGR availability has historically been limited because of frequent downtime for edge weld rebuilding as the rolls wore and short tyre life from high roll surface wear rates.Recent advancements in HPGR wear protection are now being evaluated for commercial applications in the gold and copper mining industry where this technology may offer benefits in comminuting hard and/or abrasive ores and in improving metal recovery in heap leaching applications.Proving the feasibility of HPGRs for processing competent, abrasive gold ore, Newmont Mining Corporation, the world's largest gold producer, operated an HPGR demonstration plant employing a POLYSIUS (POLYCOM) HPGR incorporating some unique wear protection, at their Lone Tree gold mine near Winnemucca, Nevada. Results of the successful demonstration are presented and evaluated in this paper.The Lone Tree HPGR demonstration plant operated for three months, from April through June 2003. The HPGR operated for 1626 hours and processed 141,000 tons of ore. This technology demonstration focused on measuring operating performance, wear characteristics, and availability of today's HPGR technology.Polysius' innovative roll surface wear protection system eliminated edge-welding downtime. Improved surface wear protection extended tyre life to predicted durations acceptable for very abrasive service. The POLYCOM HPGR is now deemed suitable for selected hard rock applications."

Jan 1, 2005

By Craig M. Sams

"Variable speed mill popularity has grown during the last 10 years with almost every SAG mill fitted with a variable speed drive. In addition, many of today’s larger ball mills are running a variable speed drive for various reasons. In the past, motor suppliers, especially gearless drive suppliers, have considered mills as being an overpriced rotor. This has lead to mills demanding more torque than what a motor can generate. This paper identifies the reasoning of what has happened and how to mitigate the mismatch in the future. Technical and economical issues are discussed, allowing mill operators to make an informed decision of which path to take in deciding what motor to put on a mill.INTRODUCTIONIt has been generally accepted in the past that motor suppliers and specialists in engineering companies understand the workings of a SAG mill or a ball mill and although there is a fair knowledge within the industry, in regards to mill torque requirements, the advent of variable speed drives in ball mills has shown the writer that a complete understanding of the mill torque requirements are not fully understood.This paper will discuss two aspects of mill torque requirements, (operating torque at various charge levels and start up torque), and how it relates to specifying the proper motor torque requirements.MILL OPERATING TORQUEMill operating torque at a given charge level and density in a mill is essentially constant throughout the entire speed range. For the purpose of this paper, we will take a 38’x 22.5’, 20’ EGL, SAG mill and provide the power draw at variable speeds but fixed loading conditions.The power draw and mill torque of this mill at 8% ball charge and 28% total loading (Highlighted) is shown below as Figure 1, at variable speeds."

Jan 1, 2007

By Denis Yaychuk, Gary Billingsley

The economic eva luation of a mineral property or mining venture should include the quantification of ri k as part of the analy is. The re ults of such an analysis provide the decision-makers not only with the most likely financial outcome and the probability of achieving that or any other outcome. but al o with a ranki ng of the relative impact of all the ri sk factors. These type of resu lts offer more complete information for investment and technical deci ions than the traditional cash flow/ ensitivity analysis. In addi tion. by attempting to quantify ri sk. the personnel providing the va ri able input are forced to take a much clo e r look at the data involved, and are fo rced to work together. the reby increa ing substantially the awa reness of the impact their work and others· work has on th e outcome of the analysis.

Jan 1, 1986

By Hua-Zhong Yu

Gold is one of the most widely used substrate materials for self-assembly. Self-assembled monolayers (SAMs) prepared from alkanethiols and their derivatives on gold are the most reliable and well-studied systems to date, which have attracted much attention because of interest in two-dimensional molecular assemblies, and of their potential applications in molecular devices, sensors, and functionalized interfaces. Gold electrodes are also very important in microelectronics and electroanalytical chemistry. This work reports the characterization of a new type of gold substrates for self-assembly. The gold substrates are constructed from recordable compact disks (R-CDs) with simple and straightforward wet-chemical treatment, and can be made at desired sizes and shapes that satisfy different experimental needs. In particular, an easy, inexpensive, and reproducible method to prepare self-assembled monolayers (SAMs) on CD-R gold substrates after removing the protective polymer films with concentrated nitric acid was described.

Oct 1, 2003

By Don A. Toth

Until recently, the fire protection systems used to protect mining equipment were based on generically designed, off the- shelf concepts. These systems were reliant on single agent approaches and were generally comprised of a series of small twenty or thirty pound chemical canisters that would discharge their contents when triggered by thermal detection means. As the equipment grew in capacity, the logic used to increase the protection was to add more chemical canisters to the system. Hydraulic excavators and large-scale mining trucks grew dramatically in size into the 1990?s and beyond; with this growth came the increase in major losses due to fire. This was evidenced throughout this period, and continues to be of great concern today. During this presentation you will learn of the significant changes that have come about as a result of this history. Today, dual-agent products, infrared detection and unit-specific, engineered systems are the primary phrases used when discussing how to best protect this equipment from fire loss. This session is a must for anybody looking to optimally protect their equipment assets and for those looking to renew and/or secure new insurance for high value equipment in the future.

Apr 1, 2005

By Manqiu Xu, Pete Winn, Steve Wilson

"In the flotation of ultramafic ores at Thompson mill, Inco Limited, CMC is used as both a floatable rock depressant and electrostatic serpentine slime dispersant. CMC, being a high molecular weight polymer, creates a serious handling problem in its introduction into the flotation processes. Typically, it is added as a 1-3% solution. This requires an enormous handling facility and makes its metallurgical gains uneconomical.Laboratory studies have shown that dry CMC addition as opposed to wet addition is feasible, as long as sufficient conditioning time is provided. Dry CMC addition into the grinding mill is also possible but its effectiveness is slightly reduced as compared to dry addition after grinding mills. Dry CMC addition using a vibratory feeder into the mill discharge is successfully applied in the treatment of ultramafic ores at Thompson mill.INTRODUCTIONManitoba Division MineralogyAt Inco’s Manitoba Division, two distinctly different sulphide ores are processed at the Thompson mill - primarily by froth flotation. The Thompson and Birchtree mines are both located within the Thompson Nickel belt. Sulphide mineralogy is relatively simple and includes both hexagonal and monoclinic pyrrhotite, pentlandite and minor chalcopyrite hosted in metasedimentary and metavolcanic rocks. The significant difference between the two mines is the amount of ultramafic rock associations in the host material. Increasingly, more of the ultramafic associated ores from the Birchtree mine are being processed through the mill with a characteristic poor metallurgy."

Jan 1, 2000

By I. Dimitrov, S. R. McCutcheon

"Industrial-grade limestone is found in both the Lower Silurian La Vieille Formation and Upper Silurian LaPlante Formation of the Chaleurs Group in northern New Brunswick. Currently, between 150 000 and 200 000 tonnes of limestone are produced per year from the proximal facies of the LaPlante Formation at the Sormany quarry of Elmtree Resources Ltd., located west of Bathurst.The proximal facies of the LaPlante Formation was deposited on the margins of tectonically uplifted Ordovician terranes. This facies comprises stromatoporoidal-algal bindstone intercalated with wackestone, packstone, and floatstone in variable proportions. The distal facies comprises calcareous shale and minor limestone deposited deeper offshore.Folding and faulting related to Middle Devonian Acadian tectonism have caused an increase in the apparent thickness of the limestone sequences, especially adjacent to the regional Rocky Brook-Millstream fault. Structural and stratigraphic observations indicate that some of the limestone bodies in the area have been tectonically displaced from their site of deposition.A variety of prospecting techniques was used to locate new limestone resources, including geological mapping, airborne and ground electromagnetic surveys, and satellite remote sensing. Clastic rock units above and below the LaPlante Formation have distinctive properties that help to trace the intervening limestone along strike. Because of water-saturated glacial cover, thick vegetation, and the small size of targets, airborne geophysical methods did not prove effective in delineating limestone beds, but aeromagnetic surveys helped map the underlying clastic unit. The remote-sensing data and especially high-resolution digital elevation models helped in identification of karst topography related to limestone."

Jan 1, 2007

By Pavel Vasak

Microseismic monitoring has become standard practice in the mining industry as a ground control monitoring tool at depth. Translating the information into practical hazard assessment tools for the rock mechanics practitioner is the focus of research jointly conducted at Creighton Mine by INCO Mines Technology Centre (MTC) and the Geomechanics Research Centre (GRC) in Sudbury, Ontario. Rock mass damage mechanisms are typically related to stress and the presence of geological structures. Due to well executed de-stress blasting practices at the mine, stress related problems are minimized. However, structurally related damage mechanisms associated with shear zones, faults and joints pose a substantial hazard. Identifying active structures from the dataset of seismic and microseismic events is generally problematic. We propose a new methodology that uses a combination of spacetime event density, hierarchical clustering and principal component analysis to identify planes of microseismic activity, termed active planes (APs). Once identified, the presence and intersection of active planes can be used to provide a hazard ranking for nearby excavations. The ranking is based on the standard Q rock mass classification system, with emphasis on the joint set number (Jn) and stress reduction factor (SRF) parameters. If the rock is treated as a fractured continuum, then, the Jn indicates the degree of freedom for blocks to move and hence, increased potential hazard. An increased hazard can also result if the APs are larger-scale and discrete (faults) rather than ubiquitous (joints). In this case the SRF is used as a measure of the degree of looseness in the rock mass.

May 1, 2004

By Fidelis T. Suorineni

Rockbursts are a major hazard in deep hard rock underground mining and tunneling. To date a significant number of rockbursts still defy conventional explanations. A review of rockburst case histories in the literature has shown that pillars and tabular excavations under shear loading are prone to rockbursting in situations where they are least expected under conventional knowledge of rockburst causes. Despite the evidence of the effects of shear loading on underground infrastructure, and the frequency of their occurrence, little is known about how this loading mechanism causes such large magnitude events and extensive damage. In this paper analytical and numerical modeling are used to understand the behaviour of pillars and tabular excavations under shear loading. The numerical modelling results show that pillars under shear loading are less confined than their equivalents in loaded in pure compression in the same geologic environment, and are therefore more brittle and weak. For tabular excavations under shear loading, the behaviour depends on whether such excavations are continuous, co-planar or offset with rock bridges. Analytical results based on slit theory show releasable potential energy in tabular excavations increases nonlinearly with excavation half-span. The study results are important for the safe and economic extraction of orebodies under shear loading.

May 1, 2011

By F. Mohamm

"Recent changes in regulations and scientific advances concerning selenium bioaccumulation have placed greater importance on non-biological treatment systems for selenium control. Mining wastewater contains hexavalent selenium (selenate) as the predominant aqueous species and possibly small amounts of tetravalent selenium (selenite). Non-biological removal of selenite is accomplished readily and cost effectively by ferric co-precipitation and adsorption using ferric oxyhydroxides sourced from ferric salts or iron anodes in electrocoagulation cells. Selenate on the other hand is difficult to remove. It is often incorrectly assumed that electrocoagulation is suitable for removing both selenite and selenate. Selenate removal efficiency by electrocoagulation is low and the amount of waste residue produced high. In contrast, BioteQ’s Selen-IX™ process removes selenate very efficiently and produces a much smaller amount of stable residue. The process combines selective ion exchange with electro-reduction of selenate in electrocells that physically resemble electrocoagulation cells but are designed and operated differently. This paper summarizes four years of pilot scale demonstration on a wide range of mine waters and discusses the key benefits and limitations of Selen-IX™. The pros and cons of combining ion exchange with electro-reduction in comparison to direct electro-reduction of selenate are also reviewed.INTRODUCTION Selenium in Mining and Mineral Processing Effluents Similar to sulphate and metals, selenium presence in mining and mineral processing wastewater originates from minerals contained in the mined deposits. Therefore, no organoselenium species are typically present in these kinds of waters and inorganic species including selenite (SeO32-), selenate (SeO42) and elemental selenium account for the majority, if not all, selenium present in these streams. Elemental selenium is not always present in mine water but is often contained in smelter wastewater. To comply with new environmental regulations, a successful water treatment plant must remove selenium from all these forms effectively and economically without generating by-products that are difficult to dispose of or manage. Elemental selenium can be dealt with using filtration or gravity separation in clarifiers often assisted by flocculants and/or coagulants. Mine impacted waters typically contain other forms of suspended solids which are removed from water in this way. Once the solids are removed, the selenium species that remain untreated are the dissolved forms. In mining waters this is mostly selenate with small fraction of selenite. In smelter wastewater, the majority could be selenite. It is well established that tetravalent selenium is readily removed from water by using ferric iron co-precipitation at pH > 4 (NAMC SWG, 2010). Ferric hydroxide/ferrihydrite solids act as the adsorbent for tetravalent selenium when it is in one of the ionic forms of biselenite or selenite. This treatment for tetravalent selenium is highly efficient. Therefore, tetravalent selenium removal is generally not an issue and is often easily incorporated into lime neutralization or unit operations such as electrocoagulation used for removing other metals present in mine impacted waters. Another option of dealing with tetravalent selenium is sulphide precipitation in acidic pH which produces SeS2 and can separate selenite from other metals and/or sludge produced at neutral to alkali pH."

Jan 1, 2017

By K. Janghorban

Multilayered ceramic-metal composites were produced by solid state diffusion bonding of polycrystalline alumina and three Al alloys containing 1 to 2%Sr, 2% Mg and Mg + Si (5057 Al alloy), The multilayered structures were fabricated at 610°C under a compressive stress of 3 MPa for 2 hours in He-5%H atmosphere, The ceramic-metal interfaces were studied by SEM and TEM equipped with energy dispersive spectrometer (EDS). Addition of 1 wt % Sr to Al promoted good adhesion, without producing any interfacial products, while the Al-2%Sr was poor in this regard due to the presence of dispersed A14Sr which is an intrinsic phase in the Al-Sr phase system, The Al-2%Mg alloy produced a continuous film at the interface, which was characterized to be MgAl2O4. Al alloys containing Mg and Si (5057 commercial alloy) produced not only the spinel structure (MgAl2O4), but another phase rich in Mg and Si (close to Mg2Si), These latter interfacial reaction products were not the intrinsic phases in Al-Mg alloys, and were reaction products at the Al2O3 ?Al alloy interfaces.

Jan 1, 2005

By Graham Davey

"Low speed stirred milling has been employed for many years in the metalliferous and industrial minerals industries. High speed stirred milling is a relatively new method of grinding in the metalliferous process industries. However it has been it has been in wide spread use in the industrial mineral field for over 30 years for various minerals. Many existing metallurgical operations are looking to maximize economic return from existing deposits, requiring new thinking and technologies. By combining low speed and high-speed milling fine and ultrafine grinding efficiency and operating costs can be improved.The correct selection of different fine grinding technologies is covered, when each mill is applicable and when a combination of the VERTIMILL® Grinding Mill and SMD provides the best economic solution.INTRODUCTIONUltra-fine grinding of minerals has been in wide spread use in the industrial mineral field for over 30 years. Within the last 10 years the metalliferous industry has shown interest in the ability to produce ultrafine particles, as chemical, physio-chemical and physical separation processes have advanced to be able to treat ultrafine metalliferous particles. Also as the primary mineral deposits, around the world are depleted, new more difficult deposits must be mined. Existing operations are also looking to maximize economic return from existing deposits, requiring new thinking and technologies.The traditional approach for gold containing refractory material has been to liberate the locked gold by chemically destroying the pyrite through oxidation. Roasting, pressure oxidation, and bacterial oxidation all employ various degrees of temperature, pressure and catalysis to react the pyrite with oxygen to produce iron oxide and sulfur by-products. However all of these methods are economically impacted due to specific operational added requirements and emissions controls. Pressure and bacterial oxidation have very high capital and operating costs."

Jan 1, 2006

By A. S. Moghaddam

The transportation of cemented and non-cemented mine tailings in the form of paste through pipelines is one of the main stages of paste backfill operations. For the purpose of pipeline design, the rheological properties of the materials, such as yield stress and viscosity must be determined. In this study, the yield stress of two Canadian mine tailings, for gold and copper mineralization, were studied using the vane method and slump tests. The comparison between the vane method and the slump tests indicates that the slump tests generally overestimate the yield stress values for both cemented and non-cemented paste backfills. In addition, the effects of 5% Portland cement (type 10) and mixing time on the yield stress of paste backfills were investigated. The percentage of cement as a binder agent has a direct effect on the increase of the yield stress of paste backfills. Yield stress measurements show that mixing times of 4 minutes and 12 minutes have the same effect on the yield stress values.

May 1, 2007

By V. I. Lakshmanan

Process Research ORTECH Inc. (PRO), with its in-depth knowledge on cobalt behaviour in nickel matte smelters and its novel mixed chloride hydrometallurgical processing, is developing a hybrid process to enhance cobalt recovery. PRO’s experimental data is compared with plant information on cobalt behaviour in smelters. In final stages of iron rejection in the converters, the thermodynamics of the matte-slag system dictates the undesirable transfer of the cobalt to the final converter slags. This results in much lower cobalt recovery in the product Copper/Nickel matte (<60%) in present copper and nickel smelters. This information is used to transfer cobalt into desired quantity of converter slag. The enriched cobalt slag is subjected to PRO mixed chloride process to recover nickel, and cobalt as high value salts of importance in lithium ion batteries. From a typical converter slag containing 3.5% Ni, 1.5% Co, and 1.0% Cu, PRO leach process extracts 98 % Ni, and 98 % Co, and 99% Cu. Application of this process to enhance cobalt recovery in typical Copper/Nickel smelters is presented. In addition, this will also enhance the Copper and Nickel recovery. Both these aspects are of interest to the Copper, Nickel, and cobalt producers. INTRODUCTION In pyrometallurgical extraction of copper and nickel from sulphide ores cobalt often occurs with copper and nickel. The requirement of cobalt is increasing due to its need in lithium ion cells used in electric vehicles. Therefore its efficient and economical extraction in a form suitable for use in lithium batteries is of great interest at present. In the pyrometallurgical processing of copper and nickel sulphide concentrates the concentrate is smelted to produce a furnace matte, which is then sent for converting to remove the iron to produce iron free (~1% Fe) matte for further processing to copper or nickel matte. The copper/nickel matte is processed for metals recovery by hydrometallurgical or vapo-metallurgical or oxidation – reduction routes to make market products. As shown in Figures 1 and 2 the slags are produced in the smelting step and in the converting steps. The metal losses in smelting are controlled by the oxygen pressure in that step and slag production which is controlled by concentrate grade. The slag produced in the converting step which is carried out at a higher oxygen pressure contains higher level of metals is often returned to the smelting step to increase value metals recovery.

Jan 1, 2019

By Roy Lindsay, Paul O'Hara, Gary Halverson

"The New Britannia Minesite is located in Snow Lake, Manitoba, 420 miles north of Winnipeg (figure 1). The mine previously operated from 1949 to 1958 extracting some 5.39 million tons of ore at a 0.150 opt gold grade. From 1959 to 1986 the property was held by Nor-Acme and Hudson Bay Exploration and Development and in 1987 High River Resources Ltd. Optioned the property, dewatered the mine and conducted a diamond drill program between the 1 780 and 2400 levels. In 1988 two companies, Nor-Acme Mines Ltd. and High River Gold Mines Ltd., negotiated an option agreement with INCO Gold whereby !NCO assumed management control of all site exploration work. During this period, a bulk sample of 10,000 tons was extracted from the 1780 level with no further exploration recorded after its removal. Both Hudson Bay Exploration and Development and INCO Gold conducted feasibility studies on reactivating the property but at a calculated capital cost of Cdn $70 to $80 million found the rate of return on their investment unacceptable.In 1991 !NCO Gold merged its interest with the assets of TVX Gold Inc. and in February 1994 TVX Gold Inc. and High River Gold Mines Ltd. entered into a joint venture partnership to develop the Snow Lake property, naming TVX Gold Inc. the operator. Upon completion of a feasibility study in April 1994 by Bharti Engineering Associates Inc., a decision was made to reopen the Britannia Mine at an established project cost of US $33 million.Project construction commenced in July 1994 with the hoist house excavation. The first concrete for the hoist house level footings was poured on August 4, 1994 and the project was completed on October 1, 1995 at a cost of US $36 million. The first gold pour took place November 4, 1995.This paper not only presents the metallurgical aspects of the operation but also describes the novel approach used to complete the design and construction of the site facilities."

Jan 1, 1996

By Pierre Boileau

Outline ? Who are We? ? Canada?s GHG Emissions 1990 - 2000 ? Emissions from the Petroleum Sector ? Emissions from Petroleum Exports ? Emissions from Manufacturing Industries ? Emissions from Mining and Metallurgy ? Conclusions Greenhouse Gas Division Key Functions: ? National GHG Inventory Report, Emission & Removal Trends Analysis, and Indicator Fact Sheets ? Scientific and Engineering Guidance, Technical Advice, Data Quality Assurance & Quality Control and Methodological/Data Development ? International Negotiations (FCCC) & scientific/technical guidelines (IPCC & ISO) ? Expert Review Teams (ERTs) ? Outreach ? GHG Verification Centre ? Clearinghouse ? Protocol Development

Nov 1, 2002

By Randy Clarkson

"Free gold particles occur in many base metal and precious metal mines throughout the world. Occasionally mine operators are unaware of the presence of free gold particles in their ores because they have not seen free gold hand specimens or at the working face of the mine.Due to the high density and malleability of gold, large circulating loads of free gold particles can build up over time in grinding circuits. This gold is often deposited in unintended traps throughout the mineral processing system.These unidentified free gold deposits represent a serious security risk as well as inaccessible inventory of gold. Deposits of free gold particles often remain undetected by mine management until they are accidentally discovered while repairing mill equipment. The trapping and subsequent release of gold particles can frustrate attempts to calculate accurate metallurgical balances.Nuclear tracers have been used to determine the free gold recovery efficiency of gravity recovery equipment, drills, and sampling equipment (Clarkson, 1994, 1997, 1998, 1999 and Walsh, 1986, 1992). In 1995, the author used radiotracers to locate and eliminate gold traps at La Mine Doyon (Clarkson, 1997). In 1998 and 2001, the author also salted mineral processing circuits at Royal Oak's Pamour Mine in Timmins (Clarkson, 1999) and at Gold Corp’s Red Lake Mine in Ontario with radioactive gold particles.The gamma and X-ray radiation from gold's nuclear isotope (Au198) were detected through steel, in pipes, and in moving equipment with scintillometers. The radiotracers proved to be a safe, rapid and accurate method of identifying gold traps, improving security, determining the recovery efficiency of Knelson gold concentrators and estimating retention times of gold particles in various processes."

Jan 1, 2003

By C. Larsen, D. Fragomeni, A. Vien, D. G. Fisher

"MOCCA is a Multivariable Optimal Constrained Control Algorithm developed specifically for non-square industrial control applications with practical difficulties such as interactions, time delays, constraints, modelling errors, etc. MOCCA consists of an off-line simulation/translation module, for tuning the control parameters, and an on-line module that implements the designed control law.This paper describes an evaluation of MOCCA on the Hemlo grinding circuit which comprises one open circuit ball mill and two closed circuit ball mills in series. In this case a 4x4 unconstrained control problem was considered. The manipulated variables included the fresh ore feed rate and three pump box water additions. The controlled variables were the grinding circuit product particle size and three pump box levels. In this application soft constraints were implemented through control action and control error weighting. The feedforward capability of MOCCA was used to compensate for a measured water flow disturbance to one of the pump boxes. MOCCA performed very well during plant evaluations when compared to the original classical multi-loop control strategy and proved to be quite robust. Perhaps most importantly, the process engineers and plant operators have a high level of comfort both in understanding MOCCA's general operating principles, and with its demonstrated performance."

Jan 1, 1991

By Glenn Kosick, John Starkey, Glenn Dobby

"A practical new test has been developed for SAG hardness determination. Using two kilogram samples of minus one inch diamond drill core or crushed muck samples, the Starkey SAG Test has been shown to give accurate predictive information which directly relates to on-stream SAG mill performance. Typical results and test criteria are discussed in the paperAchievements to date include:• Identification of hardness profiles and the location of hard and soft zones in a large ore body.• Accurate prediction of the hardness of a bulk sample by using an adjacent diamond drill hole.• Derivation of a plotted curve relating pilot plant power to laboratory relative hardness.• Demonstration that for every test done to date, the Starkey SAG Test produced a product size distribution identical to that produced in a pilot plant or full scale plant SAG operation.This test can now be used for blast hardness monitoring and short term control of mine production in existing plants and for identifying the proper locations for bulk samples in new projects. In addition, new SAG mill design can now be rationalized in a low cost way to eliminate unforeseen production shortfalls.IntroductionThis paper is presented to introduce the Starkey SAG Test, a practical new laboratory tool for measuring the relative hardness of small ore samples in a semi-autogenous grinding (SAG) environment. The test was first designed for use on diamond drill core samples during the prefeasibility stage of new mining projects, to provide new information about the ore body at reasonable cost. It is a new tool and does not replace existing pilot plant test requirements.The test will also be useful for throughput prediction in existing SAG plants by assisting in short and long term mine planning, where forecasting of metal grades and milled tonnage is used to control mine profitability. Because in-plant hardness testing has previously been unavailable on small samples, this test offers exciting possibilities for SAG mill operations where hardness variation is or could be a problem.The Starkey SAG Test provides the following benefits to the mining industry"

Jan 1, 1994