Search Documents

By Brimblecombe P

Morwell Open Cut is a continuous mining operation employing 5 buck- etwheel excavators, I bucket chain excavator and 54 conveyors. The combined bunkering capacity at both client Power Stations represents less than 12 hours maximum coal demand. This creates an extremely dynamic operating environment, which is further complicated with significant variations in both excavating and transportation plant capabilities. To achieve set objectives, including- I adequate reserves, 2 coal supply reliability, 3 cyclic plant maintenance, 4 minimal cost of coal, scheduling of the operation requires constant monitoring and reappraisal. Investigations are in progress to develop a computer based scheduling tool capable of simulating the complex operating environment. A review of computer scheduling packages currently available within the State Electricity Commission of Victoria has found limitations making most unsuitable for the task. The type of package found to be most suited is a knowledge based system ('Expert System')capable of operating within a set of rules defined by the user. Work is proceeding on the development of a knowledge base to test the effectiveness of Personal Computer based `Expert Systems'.

Jan 1, 1989

By Holliday R, Floyd JM

A laboratory investigation was carried out to determine the distribution of gold between the products of lead-zinc concentrate smelting in the Imperial Smelting Furnace (ISF). Bullion, speiss and slag from the ISF at Cockle Creek were used as the starting materials to evaluate the effect of gold and copper content of products on the distribution of gold between phases under conditions simulating those in the ISF hearth. The ratio of gold in bullion to gold in speiss has a mean value of approximately 1.6 and is independent of the gold content of the bullion. The distribution coefficient of gold between bullion and speiss is dependent on the copper level in speiss and is lowered by increasing copper content in speiss. The ratio of gold in bullion to gold in slag is in the range 25 to 5700 and dependent on the gold content of the bullion. For low gold concentrations in bullion of the order of 1 g/t and a bullion to slag ratio of 1:3 the gold loss to slag is expected to be approx- imately 23%. In all tests the gold in slag remained low, in the range 0.05 to 0.5 ppm provided metal prills were not suspended in Slag.

Jan 1, 1986

The importance of orebody definition and optimisation in project development cannot be overstated. Inappropriate orebody definition is the single most important reason for project under performance and/or failure. Without the firm foundation of good orebody definition, the structure of a project cannot be assembled reliably. Many factors need to be considered in the process of orebody definition. These factors are well summed up in paragraph 123 of The Institute's Code and Guidelines for Assessment and Valuation of Mineral Assets and Mineral Securities (Valmin Code). The factors range from the initial geological data through assaying, geotechnical and hydrogeological factors to mining and metallurgical considerations. There are other factors which also need to be considered including marketing and environmental factors. This paper briefly reviews some of these factors and their impact on project development. Three examples are presented where one or more of these factors have had significant impact on the development of the Project.

Jan 1, 1997

By Thorburn D

This paper reviews the history of environmental assessment in New Zealand with reference to mineral developments. Emphasis is given to larger more controversial projects particularly metal mines. The changing role and application of the Environmental Protection and Enhancement Procedures is examined in the context of changes in the government's environmental administration and the response of the Ministry of Energy's resource allocation group. Conclusions are drawn on the effectiveness of the present environmental assessment activities and on the allocation of administration of priorities in the Ministry. The Ministry of Energy has effectively ceased to exist.

Jan 1, 1990

By Jeffery RI, Pollard CA, Fear NJ

The paper describes the detailed hydrogeological studies carried out prior to the sinking of twin shafts at British Coal's new mine at Asfordby, Leicestershire, UK. The test methods for assessing potential groundwater inflows to the shafts are discussed and details are given of the ground freezing scheme employed through the major aquifer zone in the Sherwood Sandstone at a depth of 375 metres. During shaft sinking pressure recovery tests were carried out to further assess potential inflows and the results are compared with those from the surface tests prior to sinking.

Jan 1, 1988

By Walker K, Burton RC

An outline of the ventilation and refrigeration requirements of deep South African gold mines is presented. This is followed by a brief description of the history of controlled recirculation in mines and the practical and economic benefits such schemes can offer. The potential hazard of a fire in a recirculation system is discussed.The major part of the paper describes the first large-scale field trial of controlled recirculation to be conducted in South Africa. Emphasis is placed on the monitoring system that was used for data acquisition during the trial, and also on a safety system designed to shut off the recirculation fans in the event of a fire.The paper concludes with a review of the latest development work taking place on recirc-ulation safety systems.

Jan 1, 1985

This paper describes a case history of using an integrated geochemical and hydrogeological approach to predicting solute transport from gold mine tailings in highly fractured volcanic terrain. Two modes of transport are identified, namely discrete fissure flow and diffuse seepage through the intervening weathered rock. A simple mass balance approach is used to predict concentrations at points of emergence because most of the seepage migration will be by way of the discrete fissures where advective transport will predominate. The mass balance method has been modified to allow for natural degradation of weak acid dissociable cyanide. The long term effects of diffuse seepage are also examined.

Jan 1, 1988

By Chugh Y. P

A generalized void diffusion model for subsidence prediction has been developed based on theoretical concepts and physical principles. The general form of the model is a three-dimensional differential equation. With a few assumptions on the characteristics of overburden strata overlying typical room-and-pillar mining or longwall mining systems, specific solutions for the differential equation were obtained. A brief description of these solutions and their applications in the United States and China are presented in this paper.

Jan 1, 1992

During late 1953 and early 1954, tests were carried out in Sydney metropolitan brickpits in order to determine if some improvement might not be effected in the personal shock, fly rock and possible ground displacement accompanying daily blasting occurrences in the numerous quarrying activities of the metropolitan area. As a result of this preliminary work (Reid, 1954), the Department of Mines decided to further investigate the problem with a view to placing this type of blasting on a sound economical and safe basis for both operator and nearby residents alike. To assist in the work, a Cambridge Universal vibrograph was acquired.Human safety was the first consideration followed by property damage to homes and factories in the extractive areas. Although most of the actual field work has been confined to the Sydney metropolitan area and in particular to the large clay-shale quarries, many cities and country towns have blasting problems associated with the extractive industries, engineering projects both above and below ground level, and in building excavations to which the results may apply.The following figures illustrate how much activity of this type is located around cities and towns:Sydney Metropolitan Area:

Jan 1, 1958

The 1980's have produced an outstanding revival of the Australian gold industry. In contrast to some previous mining booms, the economic aspects of the growth in gold production are soundly based. In general the new developments have been highly profitable and this is beneficial to all parties- whether they be government, shareholders employees or suppliers. Mining companies are showing a large commitment to gold exploration with approximately 50% of Australian exploration budgets now being directed towards gold. An increasing proportion of this expenditure is being channelled towards the eastern States with Queensland 'being the major centre of interest. Further strong growth in production is expected with some 50 projects likely to come on stream before 1990. A very significant aspect of the foundation for this growth is a continuation of the existing tax status of the industry.

Jan 1, 1987

By Rosengren KJ

Geotechnical conditions often have a critical influence on the design of new open pit and underground mines, but they are often considered of secondary importance in relation to other factors, such as detailed geology, orebody geometry and grade distribution. As a result, geotechnical studies may not be carried out during early project investigations or, at best, may be given only superficial attention, often to the overall detriment of the project. Technically and economically, it is logical that geotechnical studies should be integrated with geological investigations as soon as it becomes evident that the particular deposit may prove to be economic. The paper discusses the use of geotechnical information in the selection of mining methods and mine design for underground mines and for wall design and assessment of excavation characteristics in open pit mines. It then considers methods of obtaining the relevant data, with particular reference to exploration boreholes. Selected case studies on the application of geotechnical data to mine design are Included.

Jan 1, 1986

By Coppock BW

Sintering of lead and zinc concentrates is practised by Sulphide Corporation Pty. Limited to provide both desuiphurised lump sinter feed, for simultaneous reduction to zinc and lead in the Imperial Smelting Process blast furnace, and sulphur dioxide gas for sulphuric acid manufacture. From November, 1969 a 20 percent increase in production rate has been obtained through improvements in operating technique. A gradual increase in bed permeability was achieved by modifications to the feed mix conditioning equipment and by improving moisture control. However advantage could not be taken of the higher permeability to increase sulphur elimination because the hardness of the lump sinter decreased. Higher throughput, better quality sinter and more stable sintering conditions were however made possible by simultaneously: 1. reducing segregation and compaction in the sinter bed, by narrowing the discharge opening of the main layer feed hopper, 2. reducing the sizing of sinter returns to give a closer size spectrum of particles in the feed mix, and 3. increasing the sulphide sulphur content of the feed mix to give higher bed Temperatures.

Jan 1, 1972

The Devonian Mount Morgan gold-copper deposit was situated on the western margin of the Calliope Volcanic Are assemblage, in the northern New England Orogen. Recorded production from commencement of mining in 1882 to mine closure in 1989 stand

Jan 1, 1994

Robertson Diasol have developed a spectral gamma-gamma tool fully able to withstand borehole conditions. Spectral data is digitally recorded across 256 channels depending on energy levels of the photoelectric effect. Data processing is being developed with the objective of calibrating channel amplitudes to mineral type which will lead to a direct log of selected mineral grade as a continuous trace with depth.

Jan 1, 1990

By Lu T. K

A new type of rockbolting system, the self drilling rockbolt, has been studied to develop a 'single pass' bolt for use in rockbolt installation in underground engineering. This single pass bolt forms the basis of a Rapid Face Bolting system which will reduce the amount of time spent in securing a roof during the operation of a continuous miner in the development of a panel.The installation efficiency and anchorage tests were performed in the laboratory on the self drilling bolt and the traditional resin anchorage. bolt. The results of both bolts are cmmnared.

Jan 1, 1993

By R Bunduwongse

The oil crisis had repercussions throughout the world and most importantly on mining, where the drive to reduce the use of liquid fossil fuel led directly to the appearance and subsequent growth in the design of mobile crushers in late 1970s early 1980s, which heralded a new era in both quarrying and mining. Even though mobile crushing has now become common, even preferred in the quarrying industry, this has not been the case in mining. This paper looks at why, in spite of the initial optimism, this technology has yet to gain full acceptance in the mining industry. The paper examines some of the problems that have been encountered in the past and offers suggestions as to how they can be avoided by applying the appropriate technology. It then takes a look at the successful application of the semi-mobile in-pit crushing system used by Italian Thai Development Company (ITD), on the Mae Moh Phase 5 contract and examines how the techniques used successfully there could be applied to the industry at large.

Jan 1, 2007

Hydraulic transport of coal has been used for many years on the West Coast of New Zealand to extract small blocks of steeply dipping coal. Recent development at Strongman 2 Mine has seen the use of high pressure monitors to cut coal and a corresponding increase in the scale of production.This paper provides a brief introduction to hydraulic mining, describes the present system used at Strongman 2 and discusses future potential development.

Jan 1, 1998

By Ellery B. I

Field investigations recently undertaken by Utah Development Company (U.D.C.) have been developed to allow the assessment of ground conditions relevant to the use of large bucket wheel excavators for pre-stripping overburden. "Bucketwheel diggability" predictions were made on the basis of a wedge test which was perform- -ed in the field on nominal 150 mm diameter drill core samples. Specific separation force (calculated from the wedge test results) for different rock horizons were theoretically related to the excavation rates of various sized bucketwheels, i.e., "bucketwheel diggability". The specific separation force was shown to vary with lithology, structure, weathering and moisture changes. By correlating these features between boreholes, an overall assessment of bucketwheel diggability was then made. The approach adopted to assess bucket- wheel diggability incorporated various levels of investigation. Initially, a reconnaissance stage provided information from widely spaced 150 mm cored holes to compare and contrast areas with differing bucketwheel digging char- -acteristics. The following stages progressive -ly added to this information, until finally, between hole correlations, allowed calculations to be made of volumes of materials of similar

Jan 1, 1981

By P Carrasco, E Me, M Campos, J Tapia

Correct sampling practices are of vital importance to the mining industry; key decisions for the business are made on the basis of samples in all the value chain. Geology plays a relevant role in pre- and post-investment stages. Actually the understanding of natural variability is essential for geological modelling, geometallurgical modelling, mine planning, grade and process control. Improper sampling practices obstruct this objective introducing irrelevant variability components, which can cause monumental economic losses. A good approach to accomplish this understanding is the application of heterogeneity and IngamellsÆs tests, which are useful tools to quantify the variability of a certain well-delimited geological unit at different comminution scales. The application of heterogeneity test can help minimise Pierre GyÆs fundamental sampling error and to study the impact of other sampling errors. IngamellÆs test allows us to define the correct mass of sample for chemical analysis. This paper presents the results of several heterogeneity and IngamellsÆs tests done in Chilean porphyry copper deposits that belong to CODELCO Chile (Chuquicamata, Mina Sur, Radomiro Tomic, El Salvador, Andina and Teniente), in different geological units (endogenous oxides, exotic oxides, supergene sulfides and hypogene sulfides) and for several elements (Cut, Cus, Mo and As). These tests, considering the natural variability, have helped us develop accurate sampling protocols to minimise the fundamental error to acceptable levels. A major contribution of these tests (more than 30) is the generation of secure sampling protocols using the highest sampling constant obtained in the tests, for new porphyry copper deposits that donÆt have information given by heterogeneity and IngamellsÆs tests.

Jan 1, 2005

DURING the four years, 1922, 1923, 1924, and 1925, China produced the following quantities of non-ferrous metals and ores: Antimony Products - 67,869 (long) tons. The production for 1925 was 20,869 tons, of which 80% was regulus, 14% crude,and 6% oxide.Arsenic (White) - 4200 tons. The production for 1925 was 1200 tons, but only 90 tons were exported, some 25% of which to Hong-Kong, France, and U.S.A. each, and the rest in small lots to other countries. Domestic consumption was 1110 tons, and thelocal price for "cake" was around £47 per ton on 1925 exchange.Arsenic Ore (Realgar) - 1400 tons.Lead Ore (Galena) - 44,853 tons. The production for 1925 was 10,853 tons, of which 16%, produced in Korea, went to Japan, and 84% produced in Hunan, went to Europe.Manganese Ore (Pyrolusite) - 142,567 tons. The production for 1925 was 42,567 tons, of which 94.3% went to Japan.Tin Ingot - 33,480 tons. In 1925 the exports to Hong-Kong were 8880 tons of usual rough tin of 94% to 96%. Most of this was refined to No. I Chinese quality of 99.3% and exported to U.S.A. and Europe, owing to the good price ruling.Sulphur - 12,000 tons. Sulphur is included in this list in order to explain how its production led to the discovery of some other ores.Wolfram - 19,668 tons. The production in 1925 was 5868 tons, most of which came from the Quee Mee mountain district in South Kiangsi, from the detrital deposits. Civil disturbances prevented the usual output from Hunan border.Zinc Ore (Blende) - 134,190 tons. Exports for 1925 were 34,190 tons of low-grade ore, averaging 30% zinc, 14% lead, and 7% silver...

Jan 1, 1927