Search Documents

By Takeuchi T, Matsugaki K

We have developed a new shotcreting which is suitable for the primary support of TBM tun- nelling in soft rock. This spraying compound is made from cement, a special accelerating agent and glass fiber. It can be sprayed on to a rock surface using a specially designed gun similar to paint-spraying equipment. Some of the characteristics of this method are as follows: 1) If spraying is done keeping the distance between the gun and the rock surface be- tween 0.2 and 3.0 m, the rebound losses are small and there is little dust. 2) This method can be used on excavated rock surfaces under inflowing water conditions of up to 10 i/m2òmin. 3) After 1 day the compressive strengthes of the sprayed material is greater than 250 kgf/cm2.

Jan 1, 1987

By Travis G. A

The Mons Cupri Cu-Pb-Zn deposit is situated within a complex Archaean volcanic sequence dominated by rhyolitic fragmental rocks. This sequence is underlain by a 150 m group of rhyolitic ash flow tuffs with minor conglomerate and sandstone, and is overlain by approximately 180 m of dacite and andesite flows. The Mons Cupri sequence itself consists of several elongate or circular rhyolite domes, flanked by rhyolitic fragmental rocks ranging up to 400 m in thickness away from the domes. The lithology of clasts (typically 1 cm to 1.5 m in size) provides strong evidence that the flanking fragmental unit was derived by explosive eruptions associated with the rhyolite domes. An approximately 15 m thick shale horizon, bleached and silicified at its base, overlies both the rhyolite domes and the frag- mental unit. A south-dipping chloritic pipe-like body, with near-surface dimensions of 1,000 by 250 m and narrowing at depth to produce a cone-shaped cross section, lies within the rhyolitic frag- mental rocks about 250 m north of the largest rhyolite'dome in the Mons Cupri vicinity. Its east west elongation parallels that of the rhyolite dome. Ghost fragments indicate that the material in this fissure is a severely chloritized derivative of the rhyolitic frag- mental unit. The chloritic pipe is overlain

Jan 1, 1973

By Cocker A

Pre-splitting for smooth highwall formation is conducted in around 75 per cent of surface coal operations within Australia. The CMTE (Centre for Mining Technology and Equipment) in conjunction with BHPAC (BHP Australia Coal) initiated a project to look at pre-splitting and to investigate the notching of blastholes for fracture plane control. The notching was specifically for pre-split initiation and also for discing of the toe of the production holes to minimise coal loss from the top of the coal seam. There are currently a number of factors which are driving the introduction of new pre-splitting technologies and products. The first is the ever increasing bench height being employed in strip mines which require a higher quality wall with less blast damage to maintain stability. Currently depths of 55 metres are common place with depths of 70 - 80 metres fast approaching. The second factor is the introduction of new technologies or methods which require a high quality highwall produced, eg highwall mining. This paper discusses the current state-of-the-art in pre-splitting and the main issues facing successful pre-splitting in the future. The use of a blasthole notching technology to promote fracturing along the pre-split line is also analysed. The review indicates that most pre-splitting challenges in the future can be addressed through better use and developments of current drill and blast technology. It is also concluded that a blasthole notching technique may find niche applications in improving final walls within a surface coal mine, especially where a high quality wall is required. The notched blasthole method may also allow pre-splitting in ground conditions and adverse rock structure which currently cannot be pre-split by existing technology.

Jan 1, 1995

By Lovitt M

Ora Banda Gold Mine is located in the Eastern Goldfields of Western Australia. Mining is carried out underground by sublevel open sloping resulting in large open stopes. A Mass Blast of approximately 250 000 tonnes was carried out in July 1994 to recover a rib pillar between two stopes, and the crown pillar between the underground mine and the abandoned open pit above. Strategic development within 50 m of the blast consisted of two ventilation shafts and the main decline. This development required careful design and prediction of the blast results. This paper describes the design of the blast, the prediction of the likely effects, the measures taken to reduce the risk to important development, and the results of the blast.

Jan 1, 1995

By Laffin N. W

Invariably when a new plant is cammissioned operations personnel on takeover look at ways and means of reducing certain restrictions and improving process conditions. These improvements are generally of a mechanical/engineering nature with minor metallurgical alterations to fine tune and maximise recovery. Most operations are continually reviewing and updating existing equipment and equipment spares to gain the maximum performance hereby reducing operating costs. Design of current carbon-in-pulp/carbon- in-leach (CIP/CIL) plants has evolved to such a high degree that many of the medium sized plants can have a "blue printed" design from one to the next if the same engineering designer is used.

Jan 1, 1989

By Stewart WJ

Australia's first offshsore well was spudded in on 27th December 1964 and resulted in the discovery of the Barracouta gas field. Further exploratory drilling led to the discovery of the Marlin gas field in December 1965, the Kingfish oil field in April 1967 and the Hblibut oil field in June. 1967. In September 1968, a small oil reservoir was found in a sand below the main Barracouta'gas reservoir. The Snapper gas field was discovered in May, 1968 Information on exploration activities associated with the discovery of oil and gas in the Bass Strait area may be found in the paper, "Exploration in the Gippsland, Bass and Otway Basins, Australia" by B. M. Hopkins. _ Development of the commercial fields is being undertaken on an equal participation basis by Hematite Petroleum Pty. Ltd. and Esso Exploration and Production Australia Inc. Esso Standard Oil (Australia) Ltd. is responsible for the design, construction and operation of the production facilities.

Jan 1, 1970

By Denby B, Hollands R. Schofield D

Surface mines are in operation worldwide, the vast majority employ large haul trucks for the transfer of material both to the outside world and around the site. The sheer size of these trucks and the operating conditions means there is a high

Jan 1, 1998

Mssissippi Valley-type (MVT) and sedimentary-exhalative (SEDEX) zinc-lead deposits represent about half to three-quarters of the world's production and reserves of lead and zinc. The two deposit-types have traditionally been regarded as separate entities in terms of genesis largely because they possess very different morphologies, resulting from the epigenetic nature of MVT deposits and the syngenetic origin of SEDEX deposits. Similarities in regional setting, metal ratios, size and grade, lead and sulphur isotopes, and source(s) of fluids and metals in the two deposit-types, however, suggest that they could be products of similar genetic processes. The physical properties of MVT ore fluids suggest that certain types of SEDEX deposits could have been formed from fluids possessing similar salinities and temperatures. The hypothesis is further strengthened by the facts that: 1. in several cases MVT and SEDEX mineralisation occurs in the same region, and 2. recent advances in establishing the timing of MVT mineralisation has revealed that some MVT deposits are contemporaneous with nearby SEDEX deposits. If MVT and SEDEX zinc-lead deposits do indeed share a common ultimate derivation from fluids that emanated from sedimentary basins, then the presence of one deposit-type in a region could be used to infer the possible presence of undetected deposits of the other type. Furthermore, knowledge of the mineralisation age of one type will constrain the exploration target host rocks of the other type. A genetic relationship between MVT and SEDEX mineralisation may also explain why certain individual deposits, such as several in Ireland and eastern Canada, appear to be 'hybrids' and possess geological attributes of both end-member types.

Jan 1, 1993

By Pilkington T, Noy A

The Yallourn North Extension (YNX) open cut mine ceased mining operations in early 1989. YNX may be used again for coal supply at the discretion of the Coal Corporation Of Victoria (CCV); this has resulted in the need for interim rehabilitation of the site which may last many years, or indeed, permanently.The site has suffered substantial surface erosion over the years with large areas of bare clay and coal batters remaining exposed. The first priority is to reduce the quantity and improve the quality of stormwater runoff from the site. This is best achieved by appropriate revegetation and the use of existing landform depressions as silt trap/wetland areas. Proposed rehabilitation needed to take into account the sensitive fire safety of the open cut and the option to re-open the mine if CCV deems appropriate.The authors detail the factors involved in the rehabilitation proposal and the multi-disciplinary approach to planning including engineers, scientists, a forester, landscape architects and community input. The rehabilitation design included early consideration of land use and ongoing maintenance issues linked to water quality improvement factors including vegetation. Engineering input was required for reshaping and clay covering exposed coal batters and the design of silt traps which will revert to wetlands in future. The integration of each discipline has produced a rehabilitation design pleasing to both the SECV and community alike.

Jan 1, 1992

The first hydraulic roof supports were installed underground in 1950s and ever since that time engineering developments have improved the supports in many different ways. However. advances in three main areas, the roof support mechanical design, hydraulic engineering and electronics have ultimately led to the point where, 35 years after that first installation. automation has been achieved and is now commonplace.The history of roof support automation has involved the continual integration of high technology engineering. Thera ate further possibilities for the future which combine to give some idea of the likelihood of there ultimately being a completely manless face.

Jan 1, 1991

By L Terrusi

The Bungaroo Valley hosts a concealed Tertiary channel iron deposit (CID) along a 17 km stretch of its length. Bungaroo Valley is approximately 0.5 km wide upstream at its easternmost extent, and 3.5 km wide downstream where it joins the Jimmawarrada Creek. The valley follows the axial trace of an anticline that plunges gently to the southeast, and the CID infills the valley. Mineralisation extends to a depth of 230 m below the surface, and almost the entire deposit occurs below the water table. Bungaroo Valley cuts through the Buckland Hills and is bounded to the north and south by steep scarps capped with the resistant Dales Gorge Member of the Brockman Iron Formation. Basement rocks are believed to be mostly Wittenoom Formation shales and dolomites, with Mount McRae Shale and Mount Sylvia Formation also present. Deep, localised depressions appear at the base of the CID sequence towards the north edge of the upstream section of the valley, while downstream the basal CID contact is relatively flat and shallow. In both cases the profile of the CID surface closely mirrors that of the basal contact. The localised depressions seen in the upstream basal CID contact produce significant variations in CID thickness of up to 100 m over short strike distances. This uneven palaeotopography is most likely due to eddying and waterfalls forming within the riverbed prior to CID deposition during a time when the water table was much lower than at present. It may also be associated with possible karsting in an underlying dolomite unit and subsequent syn- or post-depositional collapse of the overlying CID. The irregular basal contact of the Bungaroo CID sequence has implications for mining in terms of pit design and resource accessibility.

Jan 1, 2007

By P Griffin

Mill relining is a major contributor to overall plant downtime. Reducing the number of mill liner pieces removed from and replaced in the mill has a direct impact on the overall reline time and in turn, mill availability. To improve the mill availability of Ridgeway OperationsÆ 32 foot SAG mill, a number of initiatives were implemented in terms of liner design. These included the conversion of the shell from 40 to 30 rows, reducing the number of pieces from 80 to 60 each shell reline and reducing the number of pieces from 48 to 32 per feed end reline. In addition, modifications were made to the discharge end of the mill to extend the life of the outer pulp lifter and discharge cone, thereby reducing the frequency of change out. The standard radial outer pulp lifter was converted to an angled design. The discharge cone was converted to the BullnoseTM design supplied by Bradken. This paper discusses the design changes made and the expected benefits to the Ridgeway Operations in terms of mill availability improvements.

Jan 1, 2007

The microstructures exhibited by ilmenite in its association with other oxide minerals have been the subject of a number of papers, the most comprehensive of which is that by Ramdohr. The following observations in some degree extend his conclusions. They are based upon a study of about sixty specimens of "massive" ilmenite and titaniferous ores from a number of wIdely 'scattered Australian localities. Specimens of this character proved much rarer than was expected. The collection was gathered together through the generous aid of the University Geological Departments, Geological Surveys, and Natural History Museums of the several States of the Commonwealth, all of which contributed such specimens of local origin, as they possessed. Special thanks are due to Dr. E. S. Simpson, of Western Australia, who made available several highly interesting specimens, together with his...

Jan 1, 1938

It is no longer adequate in running mines and quarries to simply select the best equipment. Today's competitive international commodity markets demand superior efficiency. This requires efficient production and commercial processes together with systematic involvement of people in continuous improvement of processes. True Total Quality of Management (True TQM) principles provide an operating philosophy for maximising productivity and minimising unit costs of output. Unfortunately, even though these principles are proven in all industry sectors worldwide, they have not always been used correctly. This paper describes basic methodology for correct use of these principles to successfully improve the productivity of rock breakage production processes.

Jan 1, 1995

By Mousset-Jones P, McPherson M. J

Underground airways are characterized by irregular shape and uneven surfaces including large-scale natural roughness, fractures, and a super-imposed sand roughness. Swirls in the grooves of the wall and separation because of the periodic variation of the open cross sec- tion, due to the blasting patterns, make it almost impossible to calculate average con- vective heat transfer computationally on the bases of the geometrical description of the surface. However, dimensionless friction factors can be used to characterize the surface effect of an airway and an analogy between heat and momentum transfer can be applied to calcu- late an average convective heat transfer Coefficient.

Jan 1, 1988

By Gonzalez-Dominguez J. A, Dreisinger D. B

At Cominco's Zinc Refinery at Trail, British Columbia impurities are removed from zinc sulphate electrolyte by a two-stage purification process using zinc dust. Copper, cadmium and thallium are removed in the first stage whereas cobalt is removed in the second stage. Cobalt removal kinetics are affected by soluble antimony and copper additions to the electrolyte. This study was focused on the kinetics of cobalt removal by zinc powder cementation. Experimental variables included copper and antimony concentrations, pH and temperature. Common organic additives employed in zinc plants were studied to determine potential interactions with the cobalt removal process. Cementation products obtained from laboratory experiments and plant practice were studied using SEM. A number of significant results were obtained: 1. Copper and antimony ions were sustantially removed from solution during the early stages of the cementation reaction (within the first 15 minutes). Cobalt cementation kinetics are slow and follow a first order kinetic regime. 2. A drop in the cobalt removal rates can be correlated with a rise in the Eh of the slurry. 3. Ligninsulphonate, Percol 351 and animal glue at levels of 2 mg/L significantly impede cobalt cementation.

Jan 1, 1993

By Johns A. L

The concept of the Melbourne Underground Rail Loop and the organ- isation to achieve its construction are covered in the companion papers (Reference 1, 2) and will not be repeated here. The Victorian Railways, as well as being the eventual operator of the Loop when it is completed by MURLA, have also been responsible as "Contractors" to MURLA for the construction of the "cut and cover" or "box" tunnels and related approach works located on existing Railway property. These tunnel connections link the existing suburban system to the new underground works. The following tabulation indicates the significant work volume involved in this cut and cover tunnelling exercise and which is covered in some detail by this paper.

Jan 1, 1981

By Garland W

Access to geoscience reference informa- tion including mining and mineral processing has increased considerably in the last five years in Australia. This has been due principally to the use of computer-based information storage and retrieval systems. The main reference data base for the mineral and petroleum industries and disciplines in Australia is the Australian Earth Sciences Information System (AESIS), cooperatively developed and coordinated by the Australian Mineral Foundation (AMF). AESIS is created on the CSIRO computing network (CSIRONET) which has a CYBER 76 host computer located at the CSIRO Division of Computing Research (DCR) at Canberra. Data entry was until recently carried out by AMF using a dedicated line through the Adelaide CSIRONET node to the CYBER 76 interactive system. Data entry is now done directly at the AMF on a DEC PDP 11/44 mini computer that is also a host work station on CSIRONET. Data collection via magnetic tape media input from other computer-based systems is under development. The software used for data entry and management of the data base was developed by CSIRO CILES Systems Development Group. For public interactive online use the AESIS data base is transferred by tape to AUSINET - the Australian information net- work run by ACI Computer Services, Melbourne, where the data base is converted to a form suitable for the IBM STAIRS software. CSIRO facilities at DCR Canberra are used to produce computer type-set camera ready products and output in microform, on magnetic tape or as graphic display. Keywords: Earth sciences information, Computer applications, Information storage and retrieval, AESIS, Data bases, Australia.

Jan 1, 1983

By Rigby D, Gould K. W, Hart G. H

The variation in chemical and isotopic composition of hydrocarbon gases generated from humic source rocks in the Cooper Basin, the orth West Shelf, the agoorin oil shale deposit. ollinsville and the southern Sydney Basin is reviewed, discussed and interpreted.The primary composition of gases generated in and released from such source rocks appears to be very largely controlled by the degree of dispersion of the organic material. For example in eoaly shales, where the degree of dispersion may be high, products as generated may escape into surrounding inorganic structures where further maturational reactions may proceed. On the other hand, when the organic materials occur in massive form, as in coal seams, the hydrocarbons generated tend to be retained within the coal. Further cracking to the stage of methane generation is usually required before release of hydrocarbon products is significant.Secondary factors of importance in determining seam gas composition in the Bowen (Collinsville) and southern Sydney Basins are the invasion of coal measures by carbon dioxide from external magmatic sources and/or the vertical diffusion and loss from the surface ofgases generated at depth.Isotopic measurements of gas composition have been particularly valuable in determining the origins and histories of the gases examined, in demonstrating when gases are of mixed origins and in the prediction of gas quality in exploration.

Jan 1, 1985

By Thomas CG, Armstrong GJ, Lynch KS

A small glass walled pot grate has been used to simulate drying of iron ore pellets in a travelling grate plant. This equipment has enabled the effect of decreasing grind and de- creasing pellet bulk density on plant production to be quantitatively predicted. These predic- tions are compared with plant experience. The use of the laboratory simulator in comparing the effect of various additives on plant production is also described and substantial improvements in both the goethite and free-water drying periods are predicted.

Jan 1, 1972