Search Documents

By Lester Uren

Beginning with theoretical concepts of oil drainage, this paper demonstrates that the flow of petroleum into a well from a stratum of oil-saturated sand of uniform texture increases with the diameter of the well. This conclusion is supported by experimental evidence. It appears that if a well may be reamed to a diameter of 20 ft. within the oil sand, its production will be approximately doubled. A novel method is proposed for forming and supporting a cavity of such proportions within the oil-producing stratum. PETROLEUM occurs, in nature, as a fluid saturating the pore spaces between the grains of porous rocks or aggregations of rock particles such as sand, sandstone, conglomerate, shale, limestone, etc. The oil, under the influence of gas pressure, hydrostatic pressure, gravity, earth pressure, and, perhaps, other natural forces, is caused to flow through the porous "reservoir rock" into wells penetrating the stratum in which the oil occurs. The principal moving force is the pressure of dissolved or occluded natural gas within the oil, though this;, force is assisted by gravity and by the hydrostatic or buoyant pressure of ground water about the edges of the "pool." The wells, providing outlets to the surface, are centers of reduced pressure and the flow of rock fluids into a particular well is usually an expression of the difference in pressure existing between the space within the well and that of the stored oil .within the reservoir rock. The greater this differential pressure, the more rapidly will oil flow from the source rock into the well. Opposing movement of the oil from the reservoir rock into the well are certain natural forces related to the rock structure, such as pore friction and capillarity, and certain others related to the physical properties of the oil, such as viscosity and adhesion. The differential pressure between the well and the boundaries of the area drained by it must be sufficient to overcome the forces opposing flow if there is to be movement of oil into the well. If by any device the resistance to movement of the oil may be reduced, the oil will flow into the well at a more rapid rate and the effective area of drainage will be increased.

Jan 10, 1924

By C. K. Leith

THE purpose of these conferences has been to find some basic principles to guide us in the chaos which confronts us, to arrive at elements of a national policy. None such exists, nor, as a matter of fact, have there been any concerted efforts by the public or the mineral industry to evolve one. In the absence of such a policy the administrative agencies of the government can hardly be expected to be consistent or really effective in their handling of mineral problems, domestic or foreign. Basic Facts MINERAL reserves are unequally distributed among the nations. The principal world supplies are grouped around the north Atlantic, and nearly three-fourths of the world's total is controlled politically and commercially by English-speaking people. No one nation has a complete supply of the minerals necessary for modern industry; specialization, reciprocity, and large-scale movements between the nations are inherent in nature's unequal distribution of them. The principal sources of supply are relatively few compared with the nations to be served-a fact which determines broadly certain natural outlines of the world flow. National isolation with regard to minerals can be accomplished only through backward steps in industry and lower standards of living even in the nations possessing the most of the mineral supplies. A certain measure of unified commercial control, international in scope, is a natural consequence of the limited number of the large sources of supply. Mineral supplies for the world as a whole are so large that there is little need for concern about early exhaustion, but every nation has important problems of early exhaustion of particular minerals, which must affect their policies.

Jan 1, 1933

By T. M. Anderson

From the start of production in 1915 until 1948, underground block caving operations accounted for all of the ore production of Inspiration Consolidated Copper Co. Open pit development work began in 1947, and ore production from the open pit commenced in March 1948. Thus began the transition from underground to open pit mining which continued until August 1954. Since then, open pit mining has accounted for all ore production which presently averages 105,000 tons of ore and 75,000 tons of waste rock each week. Open pit mining operations at Inspiration is carried on in two separate pits-the Live Oak Pit and the Thornton Pit. The Live Oak Pit covers an area of approximately 1500x3000 ft and the Thornton Pit, 2500x2000 ft. The geographic centers of the two pits are 4000 ft apart and, at their nearest point, the surface slopes are 500 ft apart.

Jan 1, 1961

By Earl Bardwell

(Butte Meeting, August, 1913.) THE structural relations existing between cuprous oxide and copper were first systematically studied by Heyn1, who suggested that a study of the microstructure of refined copper might be substituted for the analytical methods in vogue for determining the oxygen content of copper coming .;from the refining furnace. Hofman, Green and Yerxa,2 in their paper A Laboratory Study of the Stages in the Refining of Copper, working along the lines suggested by Heyn, showed that a study off the microstructure could be made to yield a correct estimate of the oxygen content of the specimen of refined copper under examination. In order to determine the oxygen content of the specimen of refined copper under examination a photomicrograph was first made. From the relative areas of copper and eutectic, the percentage of cuprous oxide and the corresponding percentage of oxygen were then readily calculated. It was found that the values for oxygen thus obtained corresponded closely with the analytical results. With the idea of utilizing, this method of determining the oxygen content of each charge dipped from the refining furnaces at the Boston & Montana Reduction Plant, the physical testing laboratory was equipped with suitable apparatus for carrying out the work. It may be of interest to describe certain of the methods which have been worked out in, this connection and give such data as have been obtained bearing on the effect of the oxygen content of refined copper upon its conductivity.

Jan 7, 1913

By C. S. Roberts

THE advent of a sensitive X-ray method of analysis recently has allowed the determination of retained austenite in amounts as low as 0.3 pct.' As a result this phase has been found in quenched low carbon steels where its presence has not been generally suspected. In the course of a study of the tempering process,' retained austenite determinations were made by the X-ray method on a series of high purity Fe-C alloys and plain carbon steels. The chemical analyses of these materials and details of the hardening procedure are given in Table I. Results were obtained after quenching to 72°F (22°C) and — 321 °F (—196°C). Austenitizing temperatures were between 100" and 150°F above A, or Acm. All proeutec-toid cementite or ferrite was in solution. The combination of the results with those of Averbach, Castleman, and Cohen,' and earlier results of Esser

Jan 1, 1954

By T. M. Anderson

Open pit mining at Inspiration began in 1947 after 32 years of underground mining. Two separate pits are included in the operations: the Thornton pit, which measures approximately 2500 x 2000 ft, and the Live Oak pit, which is 1500 x 3000 ft. The geographic centers of the two pits are approximately 4000 ft apart, and at the closest point, the two slopes are only 500 ft apart. Today, much of the open pit mining is being carried out in areas which were broken by earlier underground block caving operations; less than 50% of the total material moved has required drilling and blasting. In the solid or virgin areas, the, material ranges only from soft to medium hardness, thus simplifying drilling, blasting and loading operations. As a result, most mining costs and problems have been centered around truck haulage, truck maintenance and the ever-increasing length of the grade haul.

Jan 3, 1963

Note by the Secretary.-—In the preceding communication of Mr. Rickard, in the present discussion, as printed in Trans., xxiii., the loss of quicksilver at Pestarena, reported on p. 569, as 230 and 234 grammes per metric ton, is stated as equivalent to about 74 pounds per short ton avoirdupois—an obvious error, which escaped correction in my reading of the proofs, and was not discovered until after Vol. XXIII. had left the press. The true equivalent is 0.46 pound or about 7 1/2 ounces (instead of pounds) per short ton.— R. w. R. Philip Argall, Denver, Colo. (communication to the Secretary) : Mr. Rickard's last contribution to this discussion* calls for some reply from me, if only by way of defending myself against the charge (p. 569) that my criticisms of his paper were "unnecessarily hypercritical and occasionally unfair." At the same time I am fully aware that our Transactions are not the place for mere personal controversy, and that the sole object of discussion is to define differences of opinion, and defend opposing views as a means of eliciting the truth. Mr. Rickard disclaims the statement, which he says I attributed to him, that in the slow-crushing Gilpin county mills the pyrites remain longer in the mortar than the other portions of the ore. My understanding of his statement was based on the following passages in his paper: " Particles of ore, which have heen pulverized to a fineness which would permit of their exit through the screen, are enabled to settle towards the bottom of the mortar. It would he expected that the heavy metallic minerals occurring in the ore would, because of their greater specific gravity, be most affected by this feature of the treatment. In practice this is found to be so. The fine slimes contain a large proportion of metallic sulphides, generally valuable on account of their close association with the precious metals, while the coarsest particles to be found in the tailings usually consist of quartz and other minerals forming the less heavy gangue (Trans., xxiii., 139).

Jan 1, 1895

By Rodney P. Smith

THE solubility of columbium nitride in ? iron has been determined for the temperature range 1191o to 1336°C from the nitrogen content and metallogra-phic examination of a series of Fe-Nb alloys.* (0.0 to 0.92 pct Nb) equilibrated with a purified gas mixture of 1 pct hydrogen in nitrogen. The method is the same as that used by Darken, Smith, and Filer' to determine the solubility of aluminum nitride in y iron. The variation in the furnace temperature during an equilibration period was about ± 2.0°C. Each sample was approximately 1/2 in. wide, 2 in. long, and 1/16 in. thick. A time series at 1200°C using samples of highest columbium content indicated that one day was sufficient for equilibrium; however, to be on the safe side all samples were left in the furnace for either two or three days. Afterequilibration, the samples were brought to room temperature by quenching in water. The experimental results are shown in Fig. 1. To be in accord with the values reported by Wriedt and Gonzalez2 and the temperature coefficient of our results at higher temperatures, the nitrogen content of iron at 1191oC is assumed to be slightly lower than our experimental value. Our data for the single-phase regions are not sufficiently accurate to establish an interaction coefficient for nitrogen in these alloys. However, the change in nitrogen content with change in alloy content for a number of systems (Fe-N-A1;3,1 Fe-N-Ni;372 Fe-N-Si.3949 Fe-N-V;3,5 Fe-N-Cr;3,6 Fe-N-Mo3,7) has practically the same value for the liquid alloy at a temperature near 1600°C as for the solid alloy at temperatures near 1200oC when the alloy content is below a few percent. On this basis the lines through the single-phase regions have been drawn with a slope corresponding to an increase in nitrogen of 0.0013 pct per 0.1 pct Nb.3 The straight lines through the two-phase regions were drawn with a slope corresponding to a one-to-one atom ratio of nitrogen to columbium in the nitride. The X-ray

Jan 1, 1962

By F. Twyman, D. M. Smith

THOSE chemists (they are still greatly in the minority) who use the spectroscope, use it very often, and find it almost indispensable. As a means of detecting minute quantities of the metals it is unrivalled. A metal can be readily distinguished in the presence of any other element, compound, or mixture without the necessity of separation. The qualitative analysis of the metallic constituents of a substance, which the spectroscope gives so easily, is a sure basis for planning a chemical analysis. As the determination of each element proceeds the purity of precipitates may be checked as often as desired. If, possessing these advantages, the spectroscope has been neglected in general chemistry, it is not surprising that it was neglected in metallurgical chemistry; for many of the impurities which are of industrial interest, even when they are present in a metal or alloy in small quantities, are not then always easily detected by the examination of their visible spectrum. The history of the development of the art has been given in Bureau of Standards Scientific Paper No. 444.

Jan 1, 1928

By Alden Greninger

THE time-honored description of the growth of metal crystals to form polycrystalline aggregates is one in which two important steps are con-sidered: (1) nucleation, and (2) dendritic growth, each dendrite starting from its individual nucleus and resulting (upon slow cooling, assuming no solid phase changes) in a macrograin. This picture of the process of crystallization is incomplete, and it is with the hope of enlarging upon it that the following summary and correlation of experimental results are given. MOSAIC STRUCTURE For an exact definition of the mosaic structure of metal crystals-if, indeed, one can be found that will hold for all metals-one must await the results of much experimental work in this field. The writer's investiga-tions have been confined almost entirely to copper and a few of its alloys. The following terms are proposed, and will be used in this report: Macromosaic Structure l.-Large-scale mosaic structure; more specif-ically, mosaic structure of a scale large enough to produce splitting of Laue spots on back-reflection Laue X-ray patterns2. The deviation from exact parallelism of neighboring macromosaics varies from a few

Jan 1, 1935

By C. E. Richards, C. N. Reid

The influence of preferred orientation on the incidence of defbrtnation tuinning has been studied. High-purity iron with almost vandonz grain orientation was cotnpared uitll iron of the sa)ne grain size and composilion lza,ing a strong (110) fiber texture. As expected from published work on single crgslfls, /he ))lean stress for the onset of luitzning-, and the l,olu)nt. fraclion of twinned nzaterial obserlled in lension differed fron the 1-a1ue.s it2 co?nPression for tnolerial with a slrong texlure. The llinning stress of "rctndorrl " )zalerial did not 17ary with the sense of the aPPlied unin.via1 stress, but sirprisinglg the incidence of 1c)i)zning- was about three 1i))zes greater ill conzp?&apos;ession Illon in lension. These results (Ire attributed entirely to ovienbation and may be nderslood in ler?ns of the shear slresses acting on the allowed twinning syster)is. J. HE twins most commonly formed in bcc metals may be described as regions of the crystal in which a particular set of (112) planes is homogeneously sheared by 0.707 in the appropriate ( 111) direction. A similar twin-related crystal could be produced by a shear of 1.414 in the reverse (111) direction but twinning by this large displacement has never been reported. Thus, twinning is unidirectional and a shear stress which produces twinning does not do so when its sense is reversed. The sense of a shear Stress is reversed when the loading is changed from tension to compression, or vice versa. Consequently, for a given orientation of a crystal relative to a uniaxial stress, only a fraction of the twelve (112) twinning systems are geometrically capable of operating in tension, and the remaining systems may operate only in compression. Therefore, when twinning is involved, there are expected to be differences in behavior between crystals tested in uniaxial tension and those tested in compression. This has been verified experimentally by Reid et 01.&apos; and Sherwood el al.,&apos; although a critical stress criterion was not encountered. Furthermore, twinning stresses in colmbium," tungten, tantalum,&apos; irn,&apos; i-Fe,\ nd molybdenum7 single crystals have been shown to depend critically on orientation, although again twinning did not occur at a critical value of the macroscopic shear stress. However, when twinning occurs, it generally does so on the most highly stressed systems, 1--4&apos;6&apos;8&apos;9 implying that the stress level does have some relevance to twin formation. In view of the large orientation dependence of twinning in bee single crystals, it might be expected that such an effect would be present in poly crystalline material which possesses a recrystallisation texture. Indeed, riestner" showed that the twinning stress in tension is very orientation-sensitive it1 <&apos;grain-oriented, silicon-iron;" this material possessed a very strong t c m^ii a nnr x_____k . i-_ii__ ri_______j. _x r»i_._:__i preferred orientation obtained by secondary recrystallisation. Reid et a/.&apos; observed a marked difference in the tensile and compressive yield stresses of polycrys-talline columbium which was rationalised in terms of the effect of a preferred orientation on twinning. No other such illformation is known to the authors. Several investigations of twinning in polycrystalline bcc metals have been reported in which the possible existence of a preferred orientation was not even mentioned. It is the purpose of this paper to show that there is a strong effect of texture on twinning in polycrystalline iron, and to poilt out the difficulty in eliminating preferred orientation in recrystallised metals. 1. EXPERIMENTAL METHOD Material and Specimen Preparation. Low-carbon, high-purity iron was obtained from the National Physical Laboratory in the form of $-in. diam rod which had been cold-swaged from a diam of 1 in. The composition of the material is given in Table I. The as-received bar was cold-swaged directly to 0.185 in. diam from which cylindrical tensile and compression specimens were machined. Specimen geometry is illustrated in Fig. 1. The gage length was 0.30 in. long and 0.10 in. diam; it should be noted that, apart from the extra heads which are necessary for tensile loading, the geometry and dimensions of the two types of specimen are identical. The specimens were heat treated either by sequence A or B outlined in Table 11. The essential difference between these two treatments is that in one case the material was repeatedly cycled through the y- to a-phase change in order to produce grains of almost random orientation ("random" iron)

Jan 1, 1969

By L. C. Brown, E. B. Hawbolt

The formation of grain boundary precipitates has been studied in Ag-5.64 wt pcl Al alloys at 688°C. Large-grain specinzerzs were used and the boundary misorientation measured by X-ray diffraction. At low-angle grain boundrrries Primary sideplates form. u)hile abore a 17-deg misorientation lenticular precipitates predominate. Growth of the lenticular precipitates was studied on individual grain boundaries using a statistical technique. The thickening and lengthening rates appeared to be independent of &apos;pain boundary misorientation, indicating that grain boundary diffusion was not significant in this system. The precipitates grew urith constant shape, with both the length and thickness increasing parabolically with time. The parabolic lengthening rates were unexpected since previous theory and experimerztal results had indicated linear growth. By approximating the shape of the precipitate to that of an oblate spheroid grouling with constant shape an equivalent diffusion coefficienl was calculated. The zlalue obtained was in good agreement with nleasurements obtained fron, diffusiorz couples. IF a single-phase alloy is heated or cooled to a temperature such that the phase becomes supersaturated, there is a tendency for a second phase to precipitate from it in order to remove the supersaturation. Precipitation takes place initially on grain boundaries due to preferred heterogeneous nucleation, but subsequently Widmans kitten plates may form in the grain interiors if the grain size and supersaturation are sufficient. The type of grain boundary precipitate formed depends on the nature of the boundary. Aaronson1 and clark2 have shown that grain boundary misorientation can be characterized by the simple parameter R, where and X, Y, and Z represent the minimum rotations about three orthogonal axes required to bring the two lattices forming the grain boundary into coincidence. The maximum value for R is 60 deg. In using this parameter the orientation of the grain boundary itself is, of course, neglected. However it was found in both Fe-si3 and A1-Ag2 that the precipitate shape depended only on the parameter R. Clark found that the vast majority of precipitates formed were allo-triomorphs— lens-shaped precipitates that grew along the grain boundaries. At low-angle boundaries, however, (R < 15 deg) Widmanstatten sideplates nucleated at the grain boundaries and grew into the adjacent grains. It has been reported that the rate of growth of grain boundary precipitates is controlled by diffusion within the supersaturated phase.&apos; The theories which have been developed for growth rates have assumed the diffusion coefficient constant over the composition range of the supersaturated phase. This is a fairly good approximation if the composition range involved is not large. Thickening rates have been calculated using the theory developed by Zener4 and by Frank5 for the growth of planar precipitates. A parabolic growth law

Jan 1, 1968

By N. Tiner

In an article on magnesium and its alloys, Gann and Winston! stated that manganese has a limited solubility in the liquid state. W. Schmidt2 showed a diagram according to Joseph Ruhrmann indicating that the solubility of manganese in liquid magnesium falls from about 2.65 per cent at 790°C. to about 0.5 per cent at 675°C. The curve was extrapolated to show zero solubility at the melting point of pure magnesium (Fig. I). This work suggested that at the lowest manganese contents it was not possible to detect either a eutectic or the formation of a solid solution, so that manganese was stated to be present in the structure as large individual crystals. Two years after the presentation of, these results, Gann3 brought evidence to show that some manganese is capable of dissolving to form a solid solution, any excess of manganese present then assuming chiefly the form of small blue-gray particles scattered throughout the primary magnesium crystals, occasionally in clusters but seldom at the boundaries. He presented micrographs of cast alloys containing 0.1, 0.4 and 1.0 per cent manganese that show a small amount of coring around the individual particles due to solid solution, and indicate that the location of the manganese particles is closely associated with the original dendritic structure of the primary crystallization. He also pointed out that the amount of manganese that can be dissolved in magnesium depends on the amount of other alloying elements present, the effect of the second alloying element being to decrease the amount of manganese retained in the alloy. E. Schmid and G. Siebe14 have determined the solid solubility of manganese and its variation with temperature by means of precision X-ray diffraction measurements. They found that the solubility is 3.4 per cent at 645°C. and decreases to practically zero at 200°C. It is apparent that the X-ray diffraction measurements of Schmid and Siebel are not in agreement with the results of Ruhrmann as presented by Schmidt. This disagreement, and also the lack of data on magnesium-aluminum-manganese and magnesium-zinc-manganese systems, led the author to the present investigation, to determine accurately the liquid solubility of manganese and its variation with temperature. Experimental Method The experimental method for making solubility determinations consists of saturating the molten magnesium or the alloys with manganese at various temperatures and analyzing the dip samples taken from these melts. Melting is carried out in a cylindrical steel pot heated by an electric resistance furnace. The pot had a metallic outside coating to protect the steel against oxidation, and a graphite inside lining to prevent the contamination of the melt by prolonged contact with iron. The inside diameter of the pot was 4 in. and the depth 12 inches.

Jan 1, 1945

By J. Chipman, N. J. Grant, R. Rocca

D. E. Babcock (Republic Steel Corp., Youngstown, Ohio)—With reference to eqs 7 and 8, at what temperature do they apply John Chipman (authors&apos; reply)—That was 1600°C. Dr. Babcock—You have l x 10-4 as the component for the lime and 1 or 4x10-. Now, is it by dividing one into the other you get the 400? That is assuming equivalent activity on the part of oxygen, sulphur, and magnesia. Dr. Chipman—Yes, they are calculated for 1600. Now, the first one for CaO was calculated before we had a glimpse of Dr. Rosenqvist&apos;s paper." If you take his calculation you get 14,000 cal which is very good agreement, but our calculation would be superseded by Dr. Rosenqvist&apos;s new data. Dr. Babcock—The state you assume those to be in is the liquid state, as near as you can measure? Dr. Chipman—Naturally it is based on the solid CaS, but if you add the effect of fusion on both sides it just about balances out, so the ratio would be about the same. B. M. Larsen (U. S. Steel Co., Kearny, N. J.)—If we knew the activity of sulphur in the slag instead of merely the percentage, we might be able to find some conflicting factors that balance one another out, and find that the FeO or oxygen pressure effect is really present over the whole range. Dr. Chipman—I am fairly sure we would. The activity of sulphur in the slag and the activity of CaO in the slag, if we just knew those quantities, would enable us to save a lot of this computation and assumption and all the approximations we are doing now. Mr. Larsen—Two other points perhaps should be included: 1—an independent effect of manganese in helping the desulphurization; and 2—the number of mols of constituents or number of mols of ions or whatever there is in the slag could vary with these compositions in such a way that you get dilution effects. Dr. Chipman—You can figure all that in if you want to and it might improve the degree of approximation a little bit. Maybe enough to justify the labor of calculation, inaybe not, but we did not do it. L. S. Darken (U. S. Steel Co., Kearny, N. J.)—The authors have tackled a very complicated problem in trying to tie together in one picture the desulphurizing problem over the wide range of basicity and oxidation level from that of the open hearth to that of the blast furnace. At the present state of our knowledge of slags such an ambitious undertaking necessarily involves the adoption of numerous hypotheses. Their formulation (eq 11) for the higher FeO range

Jan 1, 1952

By Chikao Nishiwaki

INTRODUCTION The Japanese dependency for mineral raw materials from foreign sources increased rapidly within the 20 years since the Korean war. During this 20 year period Japan has attempted to industrialize and develop her economy while depending mostly on heavy import of nearly all kinds of mineral raw materials. She has fabricated them using energy generated mostly by mineral fuel that are also imported. Fabricated goods are either used domestically to accelerate more fabrication industry or exported after adding more refinement or fabrication. In this paper iron ore as a major raw material for the Iron and Steel industry, three major base metals, copper, zinc and lead, and petroleum as a major energy source have been selected as examples to represent the general features of various kinds of mineral raw materials that are imported. Among other important mineral commodities for which Japan dependa upon foreign sources are: Aluminium, nickel and cobalt, potash and phosphorous 100 percent dependent and tin, tungusten, chromium and molybdenum over 95 percent dependent. IRON ORE Statistics for the important iron and steel raw materials, namely iron ore, coal and scrap iron are shown in Tables 1, 2 and Fig. 1. Iron ore is by far the most important and basic among these three commodities. There has been practically no steel or iron imported as a metal into Japan during this period. Iron ore, including aggregate such as pellets, and metallurgical coal are mostly transported in large ore cargo boats to the port where very efficient port facilities unload them directly at the steel mill site. As a result

Jan 1, 1976

By C. A. Bruch, J. F. Duffey

On the basis of metallographic and cooling-rate studies of 15 U-Zr alloys, a new version of the 6 phase region of the U-Zr phase diagram is proposed. IN several published diagrams of U-Zr alloy system:&apos; there is good agreement that at elevated temperatures complete solid solubility exists between y uranium and ß zirconium. Similarly, there is reasonably good agreement concerning the uranium-rich and zirconium-rich ends of the diagram. However, there is no agreement concerning the nature of the diagram at intermediate compositions and at temperatures below about 650°C. The early work of Saller et al.8 hows an intermediate phase, 6. In a later diagram by Saller and Rough&apos; shown in Fig. 1, the d phase field is drawn with dotted lines, indicating doubt that this phase exists. The diagram of Summers-Smith2 does not show the d phase. More recently Holden and Seymour&apos; have shown that in the composition range 40 to 60 wt pet Zr, the high-temperature ? phase, which is body-cen-tered-cubic, transforms to an ordered structure, 8. They found that the order-disorder transformation occurs between 595° and 610°C, and presented a diagram based on the study of four different alloy compositions. Most recently Saller et a1.5 presented a new diagram which differs with respect to the composition limits of the 8 field from the others proposed by these authors. The purpose of the present investigation was to determine the boundaries of the d phase field. Experimental Procedures and Results Alloys—Buttons, weighing 80 g of 15 different alloy compositions were prepared by arc melting Mal-linckrodt uranium and iodide-process zirconium in a water-cooled crucible. A controlled atmosphere of argon and helium was maintained in the furnace. Prior to making each button, a sacrificial button of zirconium was melted to increase the purity of the furnace atmosphere. Each alloy was then melted six times to improve its homogeneity. Subsequently the alloy buttons were jacketed in copper and hot rolled to slabs at 775°C. From these slabs, specimens were machined for chemical, thermal, and metallographic analyses, Table I gives both the estimated chemical composition of the alloys, and the values which were obtained by analysis. The oxygen contents varied from 0.013 to 0.032 pet, nitrogen from 0.0014 to 0.014 pet, and carbon from 0.0013 to 0.011 pet. The purity of the alloys ranged from 99.947 to 99.975 pet. Thermal Analysis—The specimens for thermal analysis were blocks 11/4 x 1/4 x % in. The bead of a calibrated thermocouple was placed between two of these blocks and molybdenum wire was wrapped around the assembly. Each assembly was sealed in a quartz capsule having an argon atmosphere. The capsule was placed inside a refractory crucible which was heated in a furnace. Using a method described by Smith,&apos; the emf of a differential thermocouple, with junctions inside and outside of the refractory crucible, was used to activate the

Jan 1, 1959

By J. W. Freeman, D. N. Frey

Fundamental reasons for the improvement in creep resistance of an austenitic alloy by cold working were investigated mainly by X-ray diffraction. The creep resistance was found to be improved by the internal stresses in the lattice of the alloy induced by the cold work. THIS investigation was concerned with the fundamental reasons for improvement in creep resistance of an austenitic alloy as a result of cold working. Also, the investigation was carried out to elucidate the conditions under which cold working could be expected to improve the creep resistance. To achieve these ends, creep resistance and internal structure were correlated for a variety of cold-worked conditions. Since the aim of the investigation was not to obtain specific and extensive information on any one alloy, creep testing was done with a single stress at 1200°F. Structural studies were carried out primarily with X-ray diffraction characteristics. The alloy used, low carbon N-155, was selected on the basis of being representative of at least some of the alloys used in gas turbines. Low carbon N-155 alloy in the form of %-in. sq bar stock was used in this investigation. The chemical composition, in percent, was: C, 0.13; Mn, 1.43; Si, 0.34; Cr, 20.73; Ni, 18.92; Co, 19.65; Mo, 3.05; W, 1.98; Cb, 0.98; N, 0.14; and Fe, balance. The bar stock was produced from a 13-in. sq billet, finished to 7/s in. round cornered square between 2060" and 1910°F. Prior to use in this particular investigation, the bar stock was solution-treated 1 hr at 2200°F and water quenched. This procedure was used in order to put the stock in a condition where effects of prior processing were minimized. Experimental Procedure The specific approach to the problem was twofold. First, the influence of cold working, under various conditions, on the creep rate under a single stress at 1200°F and on the internal structure was in part determined. Second, the effect of annealing at various times and temperatures on the creep rate and internal structure of the cold-worked samples was in part evaluated. The first step was basic to the investigation—creep resistance and structure were to be correlated. The second step was taken to see if the annealed samples showed some internal changes which could also be correlated with changes in creep resistance. This it was felt would facilitate solution of the basic problem. The creep and structural studies were carried out on samples reduced approximately 5, 15, and 40 pct at room temperature and 15 pct at temperatures up to 2200 °F. Annealing of various of the samples was done at 1200°, 1400°, 1600°, and 1800°F for time periods up to 1000 hr. Studies of the annealed samples were concentrated on materials rolled approximately 5, 15, and 40 pct at room temperature and 15 pct at 1400°F. The creep tests were carried out at 1200°F under 40,000 psi, the latter being approximately the 1000 hr rupture stress of the material

Jan 1, 1952

By M. Cohen, C. Wagner, J. E. Reynolds

If the total volume of a diffusion couple changes during the diffusion, the measurement of distance becomes ambiguous. Use of distance parameters as suggested by Hartley and Crank is discussed. For small concentration differences, the standard form of Fick&apos;s second law is retained with conventional length units and the in- terdiffusion coefficient D. It is shown how D can be calculated from experiments involving large concentration differences and analyzed in terms of distance parameters. &apos;The merits of incremental diffusion couples involving small concentration differences are emphasized. THE conventional form of Fick&apos;s second law for one-dimensional diffusion of component B in a binary solution of A and B is where c, is the concentration of component B; x, the distance; t, the time; and D, the interdiffusion coefficient which may depend on ca. Hartley and Crank&apos; have pointed out that Eq. 1 applies only if the total volume of the diffusion couple does not change during the diffusion process; otherwise, the definition of x becomes ambiguous. No change in total volume takes place if the specific volume of the solution is a linear function of the weight fraction Wb, or if the molar volume is a linear function of the mol fraction N. In some alloys, however, these relationships do not hold, and then it is necessary to introduce a modified measure of distance, 4 in order to retain the general form of Eq. 1. The application of Hartley and Crank&apos;s suggestions to diffusion in alloys has been discussed by Wagner.&apos; Relation Between Measure of Distance and Units of Concentration The definition of [ depends on the choice of units for the concentration c,, as follows: 1—If the concentration ca is measured as the weight fraction W, (or weight percent), [ = 5, has to be defined so that equal increments of contain equal increments of mass m of the solution, e.g., dm = pSdx = Sdw [2] where p is the local density of the solution, and S is the cross-sectional area in sq cm which is taken to be constant in this problem of one-dimensional diffusion." * da Silva and Mehla have demonstrated the constancy of the cross-sectional area in the usual type of diffusion couple. However, experiments involving diffusion into thin wires4, 5 may exhibit changes in cross-sectional area, and therefore are excluded from the present treatment. Thus and the unit of is gram per sq cm instead of cm. 2—If the concentration c, is the mol fraction N, must be defined so that equal increments of contain equal numbers of mols of solution, e.g., dn= (S/V)dx= Sd [41 where V is the local molar volume of the solution. Thus dt, = dx/V [51 and the unit of is mols per sq cm. 3—If, as may be advisable in the case of interstitial solutions, the concentration C is measured in terms of the molar ratio of components B and A (c,, = Y, = nH/nA, where n and nl are numbers of mols of B and A), = Y has to be defined so that equal increments of contain equal numbers of mols of A, e.g., dnA= (NAS/V)dx = Sdf [6]

Jan 1, 1954

By M. J. Pool, P. J. Spencer

Using liquid tin as the solvent metal, the heats of solution of silver and gold in dilute Ag-Au-Sn alloys have been determined at 723°K by solution calorimetry. From the values obtained, the various enthalpy interaction coefficients in the liquid solutions have been calculated. The self-interaction coefficients Au and Ag values of 2413 and -6322 cal per g-atom in binary Au-Sn and Ag-Sn alloys, respectively. For an alloy containing 0.04 mole fraction Ag, Au is equal to 2443 cal per g-atom, and in an alloy containing 0.04 mole fraction Au, Ag has a value of —8883 cal per g-atom. Ag Au has been determined as —2650 cal per g-atom. ADDITION of a second solute to a dilute binary alloy may cause striking changes in the thermodynamic characteristics of the alloy. As yet, such influences cannot be reliably predicted and it is only by accumulation and critical assessment of data that definite patterns can be established. Solute interactions in dilute solutions were first treated mathematically by Wagner,1 who derived expressions for the Gibbs energy interaction coefficients. For an alloy consisting of. two dilute solutes, i and j, in a solvent s, these coefficients are given by: where yi is the activity coefficient of component i and x represents the mole fraction of solute or solvent. Other interaction coefficients have since been established in terms of the various partial molar thermodynamic properties of an alloy; the definitions of these are summarized in a recent paper by Lupis and Elliott.2 Mathematical and experimental studies of such coefficients have received much attention recently, providing a very useful theoretical background to an understanding of the nature of solute interactions taking place in dilute solutions. One of the definitions to arise from such work has been the extension of Wagner&apos;s treatment by Lupis and Elliott4 to include an enthalpy interaction coefficient, defined as. where ?Hi is the relative partial molar enthalpy of component i. ?Hi is related to the relative partial molar enthalpy at infinite dilution, ?Hio, and to the enthalpy interaction coefficients by the expression: Values of ?Hi can often be obtained with a high degree of accuracy by calorimetry, and, if the composition of the alloy is carefully controlled by making calculated solute additions throughout a series of measurements, application of Eq. [2] will enable reliable enthalpy interaction coefficients to be determined. Partial heats of solution must be investigated as a function of solute concentrations down to xi = 0, and, since ? values are obtained from the slope of mi plotted against x, great care must be taken to obtain precise data. The data for binary systems which are presently available often require extrapolation of ?Hi values from compositions as great as xi = 0.05 or even 0.1 to obtain limiting heats of solution. Reliable enthalpy interaction coefficients are thus impossible to obtain from published data for most of the alloy systems already investigated. The aim of the present work was to determine values of Au, Ag, Ag, and Au in the limit xsn -1 for the relatively simple Ag-Au-Sn system and from these results to gain some insight into the possible influence

Jan 1, 1969

By L. D. Frink

Those actively interested in mining are fully aware of the ever-increasing difficulty of making conditions such that efficient work can be done in underground openings, especially as higher rock temperatures are encountered in depth. This is also true where an effort is being made to cut down the burden of overhead expense by working headings 24 hr. in a day if blasting is done as often as is possible in that time. That the conditions resulting from both these causes have driven the native-born Americans from the mines and that their places have been taken by less efficient foreigners is a fact that we must all admit. The great war now being fought in Europe and the educational qualification clause written into our immigration law by the last Congress will probably limit very materially the supply of labor, such as we are now using in our mines, and will force upon mine operators the necessity of making this work appeal again to Americans. Metal tubing, with blower or exhaust fans, has long been used in supplying air to dead ends where natural ventilation is impossible, or in driving the smoke from such places, or in doing both, as the need might be. Here in Butte we have now come to use canvas tubing very extensively and find that it has many advantages not possessed by the metal. The use of flexible tubing is not new, but it has not been generally used in mining operations. Recent improvements, however, in the canvas itself and in the jointing of sections and manner of suspension have so increased its usefulness that it promises to add much to the efficiency of mining. There is now on the market a product that is impervious to air, is fireproof, and has a system of jointing which permits it to be put up or taken down in a few seconds. In this article an effort will be made to explain the manner in which canvas tubing is being used in the North Butte company&apos;s operations at Butte, Mont. The accompanying photographs will, I hope, help make clear what may be done with this material.

Jan 1, 1918