Search Documents

By J. H. Scaff, W. G. Pfann

The effects of impurities on the electrical properties of silicon are discussed in a companion paper by Messrs. Scaff, Theuerer, and Schumacher.' It was shown that an ingot of silicon which contained boron and phosphorus in certain concentrations consisted partly of p-silicon and partly of n-silicon2 and that the common boundary between these regions was the source of a photo-voltage. These features were ascribed to the segregation of boron and phosphorus during solidification of the ingot. Because of different rates of segregation the first portion of the ingot to freeze contained a molar excess of boron over phosphorus and hence was p-silicon. The last-solidified region contained a molar excess of phosphorus and was n-silicon. This paper is concerned with the microscopic examination of such ingots. The microstructures are rather unusual in certain respects and their study has helped to show how the segregation of minor elements modifies the electrical properties of silicon. The microstructures of ingots prepared from two lots of silicon, designated 1 and 2, will be described. These lots were obtained from the Electro Metallurgical Co. Both contain 99.8+ pct silicon, but they differ in impurity analysis. For each lot will be shown the microstruc-ture of a slowly cooled ingot, for which the time of solidification is 6 min., and that of a rapidly cooled ingot, for which the time of solidification is 2 min. The ingots were prepared from 45 g charges of silicon. When an alloy freezes a cored structure is generally produced because of insufficient diffusion to remove concentration differences established during freezing. As a result of coring the first portion of a crystal to freeze is usually poorer in solute than equilibrium requires, while the last material to solidify is richer. In a columnar grain, growth is principally unidirectional and coring can produce a concentration gradient along the entire grain. By carrying the picture of the coring process from a single grain to an entire ingot in which columnar grains are aligned more or less radially, one can easily see that a composition gradient could be established between the outside and center of the ingot. This, to a considerable extent, occurs during the solidification of a slowly cooled ingot of silicon. Slowly Cooled Ingot In slowly cooled ingots of both lots of silicon, columnar grains which are approximately radial in direction and longest at the top of the ingot enclose a region in which the shapes and align- ment of the grains are considerably less regular. The central region is last to solidify and contains cavities and inclusions. The sketch of Fig 1 illustrates some of these features, as well as others which will be described below. If a polished section of an ingot is etched in a mixture of 2 parts of 20 pct HF and 98 parts of HNO3 the p-n barrier becomes visible. The overall shape of the barrier in a slowly-cooled ingot is roughly oval, as may be seen in Fig 1. The proportion of n-silicon, that is, the region enclosed by the barrier, is considerably greater in ingots of lot 1 than in those of lot 2. A sample about 34 x 1/8 X 1/8 in. was cut from a slowly cooled ingot of lot 1 with its long direction extending from the top of the ingot to the porous region. Thus its upper half was psilicon, its lower half n-silicon. A longitudinal face was polished and etched in the acid mixture. The areas of interest are identified in Fig 2. A band of parallel markings extends across the sample in the columnar region. These striae are roughly parallel to the upper surface of the ingot and cross grain boundaries with only slight deviations. They are quite distinct in the n-silicon,

Jan 1, 1950

By R. F. Mehl, C. S. Barrett, A. H. Geisler

THE mechanism by which the super-saturated solid solution of 20 per cent silver in aluminum decomposes has been reported in two previous publications. 1,2 The analysis of streaks in Laue photograms showed that thin platelike particles (the so-called Guinier-Preston aggregates) form upon {111} matrix planes in the early state of decomposition.1 The size of these particles is larger, the higher the temperature at which they form in accordance with nucleation theory;3 at all temperatures they increase in size with aging.2 When they have grown thick enough to afford three-dimensional diffraction, powder X-ray photograms show that the structure is not that of the equilibrium precipitate y but that of a transition lattice ?'. Since this is also platelike in shape and also lies upon the {111} matrix planes with the {110} direction in the matrix parallel to the {11.0} direction in ?', it seems likely that the original platelet particles are merely ?' in an early stage of formation, and thus finely dispersed. The atomic spacing and pattern on the {00.0} plane in ?' are identical with those on the {111} matrix plane to which it lies parallel, and since comparable directions in the two planes are parallel, the lattices are thus coherent at the interface; an analogous coherence has been found in aluminum-copper alloys.3 The structures ?' and y are both close-packed hexagonal and are oriented alike; they differ only in interatomic distances. Consequently, ? ' is regarded as y strained from its ordinary dimensions by the lattice coherency between it and the matrix.2 The lattice movements that transform the matrix to the equilibrium precipitate appear to be very simple.2 The mechanism of precipitation in this system is simpler and is more precisely known than that in any other system,2,4 hence the system should be a profitable one for the difficult task of correlating property changes with structural alterations. The present report provides additional studies on powder X-ray diffraction from alloys of 10 per cent, 20 per cent and 30 per cent Ag, and presents the correlation of crystallographic changes with changes in microstructure, Brinell hardness and electrical resistivity of the three alloys. PREPARATION OF SAMPLES AND EXPERIMENTAL PROCEDURE The preparation of the 20.2 per cent Ag alloy has been described.2 Alloys containing 9.9 and 29.7 per cent Ag were prepared from 99.97 per cent Al and 99.99+ per cent Ag using a similar procedure. Rolled

Jan 1, 1943

By John F. Elliott, David L. Schroeder

SURFACE depletion can be a significant source of error in the use of the effusion method for determining the thermodynamic properties of alloys, particularly in the case of solid alloys.' However, as yet this problem has not been treated quantitatively by experimentalists in the field.1-3 The method necessitates diffusive transport of material out of the source alloy to obtain a relevant measurement. The general character of the system is shown in Fig. 1. The diffusive flux (nD) at the alloy surface is equal to the effusive flux (nE): where D is the diffusion coefficient of the diffusing substance, C is its concentration, X is the distance from the surface into the source alloy, p is the density of the alloy, and AS is the actual available surface of the alloy. The concentration of the diffusing substance at the surface is CS, and Here fE is the Clausing factor, AE is the area (sq cm) of the orifice, y is the activity coefficient of the substance in the alloy, PO is the vapor pressure (Torr) of the pure substance, M is the molecular weight of the effusing species, and T is the absolute temperature. The differential equation for diffusive transport in the source alloy is Fick's second law. Its solution is dependent on the geometry of the source alloy. Two boundary conditions must be established to obtain the proper solution, the first being Eq. [1], or its equivalent. The solutions for several important forms of the source alloy are considered below.

Jan 1, 1967

By Walter R. Hibbard, George H. Eichelman, William P. Saunders

INTEREST in the various products of the austenite eutectoid transformation in iron-carbon alloys, particularly as produced by the isothermal sub-critical techniques introduced by Davenport and Bain,1 has resulted in the application of similar heat treatments to other eutectoid transformations. Studies2.3.4 of the beta copper-aluminum alloy eutectoid transformation revealed microstructures very similar to those found in iron-carbon alloys. Investigations5,6 of the kappa phase in the copper-silicon alloy system have established the eutectoid type transformation of this phase into terminal alpha and intermediate gamma phases. This transformation has been reported' as forming a eutectoid type structure in a very sluggish manner by a long time isothermal treatment. The purpose of the present investigation is to study the products of the kappa eutectoid transformation as affected by transformation temperatures by means of microscopic and hardness methods. PREPARATION OF ALLOYS The copper-silicon alloy equilibrium diagram is shown in Fig I. The kappa field converges to a minimum silicon solubility at the eutectoid composition and all other completely kappa alloys are hypereutectoid. Thus, kappa decomposition involves first the proeutectoid precipitation of gamma, followed by the eutectoid transformation of a lower silicon content kappa (5.2 pct). Smith5 has indicated that alloys containing between 5.4 and 5.7 pct silicon could be hot rolled, but that the latter composition was desirable in order to permit a wider kappa temperature range. The alloy was prepared by adding Baker's commercially pure silicon to an ingot of copper-silicon alloy containing 2.34 pct silicon remaining from the investigation of Brick, Martin and Angier.7 Following the casting techniques of Krynitsky, Saunders and Stern,8 the ingot was melted under a heavy layer of dried charcoal in a clay-graphite crucible in a gas-fired pot furnace. Small lumps of silicon were held under the melt surface with a graphite rod. After the silicon had dissolved, the alloy was chill-cast and then remelted without a cover, stirred thoroughly, skimmed and poured into a preheated cast iron mold. The cast microstructure is shown in Fig 2. The casting, 10 X 4 X ¾ in., was annealed at 750°C for 21 brand furnace cooled. About 1/16 in. was milled from all surfaces. The plate was cut in half longitudinally and the bottom half analyzed by A.S.T.M. methods.9 The composition by weight was as follows: copper 94.24 pct, silicon 5.56 pct, iron 0.11 pct.

Jan 1, 1948

By Y. L. Yao

It is suggested that the binary alloy systems of transition metals may be classified into groups according to "excess energy"E. For systems with positive ?E, the Laves phase, the TiNi3-, the TiCu3- and the Cudu-type rich in the smaller atom and the TizNi-type rich in the larger atom may exist. For systems with negative ?E and composed of two components of different crystal structures, the X, the Cr3O and the phase may exist on the side of the phase digrattz rich in the component with the higher "solubility factor" value am! the Cudu-type and the disordered hcp phase on the other side; if the crystal structure of two components is the same, the Cudu-type may exist on both sides. For systems with weakly positive ?E and cotnposed of different crystal structures, the u phase and the MgCd3-type may replace the Laves phase and the other types; the X, the Cr3O and the a phase may also exist. Finally, the equirnolar compounds of the CuAu- and the CsC1-type may exist irrespective of the sign of ?E. THERE are many factors which play a major role in the formation of binary intermediate phases in alloys, such as the crystal structure, the electronic structure, the atomic size and the electrochemical factor. To find the simultaneous effects of all these factors on the formation of intermediate phases of every metal would be a difficult task, especially because only a small fraction of experimental facts necessary for the complete formulation is known at present. Thus the past surveys of intermediate phases have been usually confined to few metals, several types of intermediate phases and some but not all controlling factors. In a previous paper1 the idea of "solubility factor" of metals was introduced. Although the suggested values are tentative and empirical, the formation of a continuous series of solid solutions in metals could be correlated with the interplay among the atomic size factor, the solubility factor and the crystal structure factor. The purpose of this paper is to demonstrate qualitatively the interplay of these factors in the formation of binary intermediate phases among transition metals. FACTORS CONSIDERED The Crystal Structure Factor. With rare earths excluded, the transition metals are classified into three common crystal structures listed in Table I. There is arbitrariness in the present classification of several allotropic elements. However, out of seventy-odd continuous solid solutions formed among transition metals, only six of them, namely, those

Jan 1, 1962

By T. J. Koppenaal

The surface slip line structure has been investigated by optical microscopy during the easy glide deformation of Cu-A1 single crystals as a function of composition, testing temperature and prior thermal treatment. The slip line structure in alloys of 2.5 or less at. pct Al is similar to pure copper, while alloys of 5 or more at. pct Al show slip tracings typical of a brass. Cross slip is observed in the "a-brass type" crystals and the amount of this type of slip increases rapidly with aluminum content. The cross slip tendency in 14 at. pct Al crystals is signicantly higher when tested at 150°C as compared to 4.2" and 77°K. In addition, cross slip is more pronounced in this alloy in the furnace cooled condition than when quenched from 450°C. The cross slip behavior is analyzed in terms of existing models for this type of deformation. In two previous investigations, reports of yield points1 and solid solution strengthening2 in Cu-A1 single crystals have been given. This paper enlarges upon the brief description of the slip line structure discussed in these reports. Since the easy glide slip line pattern of copper changes markedly with the addition of -30 pct Zn (-brass),3 a study of slip lines as a function of solute additions in Cu solid solutions should help to explain some of these differences. In addition to composition variables, slip lines have also been studied as a function of testing temperature and prior thermal treatment. PROCEDURE The slip line observations were made on single crystals of 0.5 to 14 at. pct Al using a light microscope. Details concerning the preparation and basic testing procedure are given elsewhere.' Prior to testing, each crystal was homogenized at 900°C for 24 hrs, furnace cooled, and electrolytically polished in a 60 pct phosphoric acid solution. The strain rate was-5 X 10 sec-I in each case. Unless otherwise stated, all observations reported upon here were made during the early stages of easy glide. RESULTS AND DISCUSSION The maximum magnification generally used was 1000X, and slip lines could be resolved down to about 105 cm (1000A). This resolution is appreciably less than obtainable with electron microscopy replica techniques where the replication can resolve slip lines down to about 40 A. Thus, while many qualitative features could be studied, the type of quantitative data obtainable with an electron microscopy replica study could not be made. Crystals containing 0.5 and 2.5 at. pct Al deform much like pure copper exhibiting a high density of fine slip lines that cover the entire gage length of the specimens. Fig. 1 shows the surface slip line pattern in a 2.5 at. pct A1 extended 0.01 shear strain at room temperature. Crystals having 5 to 14 at. pct A1 showed appreciably coarser slip lines that were generally concentrated at one end of the gage length. During easy glide these coarse slip lines propagate along the gage length in a manner similar to that observed in a-brass single crystals by Piercy, Cahn, and cottrel14 and refered to by them as a Lüders band propagation. Fig. 2 shows a typical area of these coarse slips in a 14 at. pct A1 crystal after a room temperature shear strain of 0.01. Two slip systems were apparently active. Using a method described by Cullity, the angles, between the specimen axis and the normals of the primary and secondary slip planes were determined to be 50 and 84 deg, respectively. 'From the Laue photograph, was 52, 81, 66, and 30 deg for the primary, cross, conjugate, and fourth slip planes, respectively. The secondary active plane in Fig. 2 is thus established as the cross slip plane, and the operative slip system is evidently the cross slip system, e.g., slip

Jan 1, 1963

By Kent W. Pilz

Wet dust suppression can be achieved by 1) confinement of the dust within the dust producing area with a curtain of moisture, 2) wetting of the dust by direct contact between the particles and droplets of moisture or 3) the formation of agglomerates too heavy to remain airborne, or too heavy to become airborne, by combining small dust particles with each other and with the droplets of liquid. From the standpoint of economy, availability and safety, water is the ideal fluid; however, it is not as effective for dust suppression as when small percentages of specially formulated dust control compounds are blended with it. Performance of dust control com pounds is related to surface active agents and surface activity. In all liquids there is an attractive force between molecules which varies inversely as the sixth power of the distance between molecules. Thus, in the liquid phase where molecules are crowded together, the intermolecular forces are powerful; whereas in the liquid-vapor phase where the molecules are relatively far apart, these forces diminish rapidly. In the body of a fluid there is an uneven distribution of forces resulting in an inward pull called surface tension. The force which keeps two surfaces apart or causes them to coalesce is termed interfacial tension. Fluids of high surface tension exhibit poor wetting, spreading and penetrating qualities. Water has the unusually high surface tension of 72.75 dynes per cm at 20°C.

Jan 7, 1972

By Pol Duwez, Paul Pietrokowsky

The crystal structure of the compound TisGeS has been determined from X-ray powder diffraction data. Related silicon and tin compounds have been found to be isomorphous. Unit cell dimensions, axial ratios, and parameters for equivalent atomic positions are given. THERE is, at present, only meager information pertaining to the solid state reactions of titanium with the elements in group 4B of the periodic table (silicon, germanium, tin, and lead). The only two compounds whose crystal structure has been established are TiSi² and TiGe² (references 1 and 2 respectively). These two compounds are isomor-phous and have an orthorhombic symmetry D242h— Fddd. The titanium-rich regions of the constitution diagrams of titanium-silicon, titanium-tin, and titanium-lead have been investigated by Craighead et al.³ While valuable information concerning the alpha solid solubility of these three elements in titanium was obtained, no light was shed on the existence or nature of the titanium-rich compound in these systems. The present study is concerned with the crystal structure of the intermediate phases Ti5Si ?, Ti³Ge³, and Ti5Sn³, which were found to be isostructural. The alloys were prepared by mixing the pure metal powders in the desired proportions, pressing the mixture into pellets, and melting them in an electric arc furnace in the presence of a helium atmosphere.& After melting, the specimens, weighing approximately 5 g, were sealed in evacuated quartz vials, homogenized at 1038°C for three days, and quenched from that temperature. Powder diffraction patterns were made with a 143.2 mm diam Debye-Scherrer X-ray camera in which the Ievins and Straumanis film arrangement was utilized. Filtered copper radiation was used throughout the entire investigation. A study of the powder patterns of a series of alloys of various compositions indicated the presence of a compound around a composition corresponding approximately to a ratio of 3 titanium to 2 silicon, germanium, or tin. From a visual examination of the diffraction patterns, it was evident that the silicon and germanium alloys were iso- morphous. For small angle reflections, the powder pattern of the tin compound was analogous to that of the silicon and germanium compounds, but after the first ten reflections, the similarity was no longer clear. The powder pattern of the germanium compound was selected for indexing, since it exhibited a weak small angle reflection and clearly resolved doublets in the back-reflection range. Good agreement between observed and calculated values of (1/d)² was found by indexing the pattern on the basis of hexagonal symmetry. For the hexagonal system:

Jan 1, 1952

By M. J. Duggin

Evidence is produced below to show that the carbide "Mn,C," reported by Kw,and ersson' is really a mixture of two carbides. One is an Fe-Mn carbide which is probably isomorphous with hexagonal Mn15C4, reported by Bouchand and Pruchart.' The othev is a tetragonul Fe-Mn carbide with cell dzmensions close to those reported previously by the author3 for an Fe0.1Mno. carbide. IN a recent investigation several Fe-Mn carbide specimens, each weighing about 5 g, were prepared in a manner previously reported.3 Debye-Scherrer X-ray photographs were taken of at least two samples from different parts of each specimen using a 114.6-mm-diam camera. The exposure time was 2 hr using filtered chromium radiation, a tube voltage of 35 kv and a tube current of 10 ma. In the case of one specimen, which contained nominal weight percentages of iron, manganese, and carbon of 9.40, 84. 6,, and 6.0, respectively, duplicate chemical analyses indicated f1.2 and 5.5 wt pct C to be present in the two samples taken of the specimen: no graphitic carbon was detected. One powder-diffraction pattern of this specimen indicated the presence of the tetragons: carbide reported earlier,3 (a = 6.772A, c = 9.427A), plus cementite (O), plus an unknown structure. The second powder-

Jan 1, 1970

By Fritz Wald, Richard W. Stormont

lHE general constitution of a number of metal-lead telluride and metal-tin telluride systems has recently been studied in an effort designed to furnish background information for the study of degradation mechanisms on junctions between thermoelectric power generation materials and metals.1"4 This paper reports further results of that effort. It was found that cobalt-lead telluride constitutes a stable pseudobinary section through the ternary Co-Pb-Te system. Materials used in the study were lead and tellurium of semiconductor-grade purity (American Smelting and Refining Corp., 99.999+ pet). Cobalt (Johnson Matthey & Co., 99.999 pet purity) was used in the form of slices cut from rods of 5 mm diam. Twenty- gram charges of the alloys were melted in evacuated quartz ampoules. Thermal analysis, as described previously,2'3 and metallographic and X-ray diffraction methods (Debye-Scherrer photographs) were used as investigative tools. Substantial difficulties were encountered in polishing, as reported previously for the lead telluride-iron system.3 A number of different etches were used, including dilute aqua regia, Murakami solution, an etch containing copper nitrate,3 and HC1-HNO3-acetic acid-water mixtures. None of these etches gave consistent results over the complete range of cobalt concentrations. On the alloys containing bulk cobalt in the form of primary

Jan 1, 1969

By Alden B. Grenninger

The time-honored description of the growth of metal crystals to form polycrystalline aggregates is one in which two important steps are considered: (1) nucleation, and (2) dendritic growth, each dendrite starting from its individual nucleus and resulting (upon slow cooling, assuming no solid phase changes) in a macrograin. This picture of the process of crystallization is incomplete, and it is with the hope of enlarging upon it that the following summary and correlation of experimental results are given. Mosaic Structure For an exact definition of the mosaic structure of metal crystals—if, indeed, one can be found that will hold for all metals—one must await the results of much experimental work in this field. The writer's investigations have been confined almost entirely to copper and a few of its alloys. The following terms are proposed, and will be used in this report: Macromosaic Structure1.—Large-scale mosaic structure; more specifically, mosaic structure of a scale large enough to produce splitting of Laue spots on back-reflection Laue X-ray patterns2. The deviation from exact parallelism of neighboring macromosaics varies from a few minutes to a few degrees3. Just as there are no exact dimension limits for macrograins, so the dimensions of a macromosaic vary considerably. Macromosaic structure may often be seen on copper single crystals if they are examined carefully with critical illumination4. However, back-

Jan 1, 1936

By James Marsh

INTRODUCTION Economists have long expressed suspicion of the economic theory of natural resource exhaustion, even in writing articles which have contributed to it (1). Indeed, the gap which separates the pure theory from practical management seems unusually wide. It is doubtful whether a mine manager could possibly know enough about the relevant parameters of his mine to steer it along the optimal paths described by the theorists (2). Nevertheless, enough faith in the theory remains that mine managers are suspected of being a separate breed whose behavior must be studied in special courses using specialized text-books, collections of readings, and journals (3). The implied hypothesis, that mines and natural resource firms are managed differently than other firms, is the subject of this paper. In the next section the theory is developed and analyzed. In section III, I discuss the implications of the statistical results that have been obtained. Finally, conclusions are reserved for section IV. THE MODEL A key difference between the traditional theory of natural resource production and that of other forms lies in the set of variables which ire assumed to jointly determine the quantity of output the firm will produce. Output, in the non-resource case, is assumed to be a function of k clearly definable and distinguishable inputs or factors of production, viz., y = f(xl, x2, ..., xk), (1) here

Jan 1, 1977

By J. E. Coyne, L. E. Tanner, J. E. Boyd

In recent investigations of the isothermal transformations of the retained 0 phase in a titanium alloy having 13 pct V, 11 pct Cr, and 3 to 4 pct Al, there have been indications that the w transition phase is the initial decomposition product at temperatures below about 950°C (510 c).' This metastable phase, found in a number of titanium-base alloys rich in stabilizing elements and known to have an adverse effect on their ductility and toughness, is not easily observed by the usual experimental techniques. Since wis coherent with the /3 matrix,495 distinct interphase boundaries are not revealed metallographically. However, in some cases, an etching effect (i-e., a "mottled" /3 surface) poorly resolved by light microscopy has been found to correspond with the presence of w.6 X-ray diffraction examination has generally been the most suc- cessful means for identifying this phase and crys-tallographic determinations have been made.4'5 Dynamic elastic modulus7 and electrical resistivity measurementse have also aided in the identification of w. In the current study, the electron microscope was utilized to examine microstructures in aged Ti-13V-11Cr-3A1 that were unresolvable by light microscopy techniques. Using negative parlodion replicas (shadowed with chromium at 27 1/2 deg) examination was made of various transformation

Jan 1, 1962

By Paul L. Burkhart

THOUGH at an earlier period brief studies had been made by the Lehigh Navigation Coal Company Inc., it was not until 1924 that J. B. Warriner, then general manager, called for a comprehensive study of timber treatment, treating solutions, and related operations. Because of the impossibility of procuring accurate costs and other pertinent treating data, the American Wood Preserving Co. agreed to treat a car of mine timber at the Port Reading plant of the Reading Railroad. Fig. I shows the treating data collected at the treating plant on this timber, which was installed in two of the Lehigh mines in 1925. [ ] In the latter part of 1925, a survey of the tunnels and gangways of the company's Panther Valley mines was made to determine the proportion of gangways or tunnels timbered, cause of timber failures, approximate life of the average wood set and the approximate percentage of treated timber that it would be profitable for the company to use. Results of this survey appear in Table I. Because of the high percentage of timber that gave evidence of failure by rot, as noted in Table I, and a further study of the life of the sections where timbering was necessary, it was deemed advisable to fill 25 per cent of the yearly gangway timber requirement with treated timber. QUANTITIES AND TREATMENTS OF TREATED TIMBER PURCHASED In the early days of the program, none of the large treating companies would accept orders for small quantities of treated timber and the company was compelled to state the quantity of timber it would require at each operation in each month of the year. Table 2 is an example of the tabulation given to the various treating companies to assist them in making a yearly bid on the minimum quantity of timber required by the company during the year 1931. A bill of timber was calculated for each car, the weight of which would be between the minimum and maximum weight permitted for railroad-car loading. The treating company was paid for timber upon delivery at the operation specified. As extra cars of timber were required, they were ordered from the treating company, and payment was required on their receipt, on the basis of the piece or tonnage

Jan 1, 1942

By C. F. Floe, M. Cohen, M. B. Bever, V. G. Paranjpe

P. Coheur and L. Habraken—We read this paper with great interest and are glad to congratulate the authors for their valuable work, supplying an important contribution to the mechanism of tempering on the carbides in vanadium steels. We are in a good position to appreciate this work since we have been studying, for more than a year, Cr-Mo steels of a composition similar, but less highly alloyed (namely 0.1 pct C, 3 pct Cr, 1 pct Mo). Our results are quite in concordance with the authors', however, we wish to point out that it is very interesting to use equally the electron microscope in order to observe the variations of microstructure in steels. We have studied simultaneously the evolution of the carbides in situ with the electron microscope, and, after extraction, again with the electron microscope, and then with X-rays. The first results which we have obtained have been communicated at the Congress of Delft (July 1949) and at the "Journees de la Metallurgie" in Paris (October 1949). These may be summarized as follows: After tempering with varying either the tempering temperatures or the tempering times, the carbides show two evolutions. The first one is connected to the carbides existing in the steels, principally in the boundaries of the grains. For some groups of steels these carbides may coalesce and for other groups they may

Jan 1, 1951

By N. J. Grant, D. S. Bloom

P. Coheur and L. Habraken—We read this paper with great interest and are glad to congratulate the authors for their valuable work, supplying an important contribution to the mechanism of tempering on the carbides in vanadium steels. We are in a good position to appreciate this work since we have been studying, for more than a year, Cr-Mo steels of a composition similar, but less highly alloyed (namely 0.1 pct C, 3 pct Cr, 1 pct Mo). Our results are quite in concordance with the authors', however, we wish to point out that it is very interesting to use equally the electron microscope in order to observe the variations of microstructure in steels. We have studied simultaneously the evolution of the carbides in situ with the electron microscope, and, after extraction, again with the electron microscope, and then with X-rays. The first results which we have obtained have been communicated at the Congress of Delft (July 1949) and at the "Journees de la Metallurgie" in Paris (October 1949). These may be summarized as follows: After tempering with varying either the tempering temperatures or the tempering times, the carbides show two evolutions. The first one is connected to the carbides existing in the steels, principally in the boundaries of the grains. For some groups of steels these carbides may coalesce and for other groups they may

Jan 1, 1951

By J. E. Metcalfe

Proceedings of the Fourth Empire Mining and Metallurgical Congress, Great Britain 1949. Part II published at the Offices of the Congress in London, England, 1139 pp. The price of these proceedings is £ 2. The parts may be purchased separately at a cost of £ 1 each.-Part I of this book covers a report of the organizing committee, the inaugural meeting and presidential address, banquet at Guildhall, welcome by Sir Richard Livingstone at Oxford. and final session. Technical session and papers are also covered in Part I. Part II covers such topics as coal, present-day trends in mineral dressing and metallurgy. Mining Engineer's Survey Manual. By J. E. Metcalfe. Published for "Mine & Quarry Engineering" by Electrical Press, London, 1951. 341 pp., illus., charts, diagrs., tables, 8 ¾ x 5 1/ in., cloth, 30s., available from Percival Marshall & Co., Ltd., London, and British Book Centre, 122 East 55th St., New York 22, N. Y. Beginning with a brief treatment of surveying fundamentals and a discussion of the correlation of surface and underground surveys, this practical manual continues with descriptions of surveying practice both above and below ground including stopes, inclined shafts; etc. Space is devoted to sampling and valuation, geological considerations, and descriptions of modern surveying instruments. The organization of survey operations is covered in the last chapter.

Jan 1, 1952

By S. F. Bartram, G. A. Chase

COMPUTED X-ray diffraction powder patterns of YNi3, YNi5, and CbBe3 are available on request from either author.

Jan 1, 1968

By K. Mukai, M. Ishihara

This report is a brief discussion of the impurity levels both in primary aluminum and super-purily alnminim in connection with raw materials and proc-essing methods. Particularly, truce amounls of im-purities were analyzed by introducing nittss-speclro-gruphy and nenlron-aclivalian analysis techniques. Vanadium and gallium content in primary aluminum metal corresponded to theor amounls in anode coke. but the nickel content in primary aluminum was hide-pendent oj its amount in the anode cake. Sulfur in the anode colic might result in an increase of the iron content in the molten metal in the reduction cell. The content of sodium and calcium increased with increasing bath ratio. In the holding furnacc sodium content decreased rapidly, and nonmetallic inclusions merit separated front the mollen metal. Three-layer elctrolysis was effectire in eliminating many impuri-ties with the exception of copper, aluminum oxide. aluminum nitride, and some rare-earth elements. THE amount of impurities and nonmetallic inclusions in aluminum metal depends on impurities in the raw materials and various production processes. This paper presents an investigation of the behavior of impurities and nonmetallic inclusions in aluminum during the electrolysis process, the period in the holding furnace, and the process of three-layer electrolysis. Chemical analysis and emission spectrometric analysis have generally been used as methods to determine small amounts of impurities in both primary aluminum and super-purity aluminum; however. mass spectrography and neutron-activation analysis have been recently introduced into this field, and trace amounts of impurities can accurately be determined by these latter methods. EXPERIMENTAL WORK Common impurities were determined by means of absorptiometric. polarographic, flame-photometric. and emission-spectrometric methods. However, in the determination of trace amounts of impurities and non-metallic inclusions, the following methods were applied. In the analyses of trace impurities by mass-spec- trographic analysis, samples were exposed in the vacuum spark of double-focus ing Mattauch-Herzog type mass spectrograph (Japan Electron Optics Laboratory, Ltd.). Ilford Q2 photographic plates were used as ion detectors. Fe was used as the internal standard, and the atomic concentration of each element was calculated by the following expression and converted into the weight concentration: where E, and Ei are the exposures (coulomb) when isotopes of the internal standard and impurity elements (on which the estimate is based) show the same density, X is the percent (atomic) concentration of the standard, IF and Ii are the percent abundances of the isotopes of the standard the impurity elements (on which the estimate is based), and Ms and hfi are the mass of the isotopes of the standard and impurity elements (on which the estimate is based). The coefficient of variation in this method is about 40 pct in the range of 0.1 to 1 ppm. In neutron-activation analysis, irradiations were done in the nuclear reactors TRIGA-I1 (neutron flux: 4.7 x 10 11 n per sq cm per sec; Rikkyo University) or JRR-2 (neutron flux: 2 x 1013 n per sq cm per sec: Japan Atomic Energy Research Institute). After the chemical separation, a NaI (3 by 3 in.) scintillator connected to a 256-channel y-ray spectrometer (R.C.L.) was used for counting and recording various activated impurities. The coefficient of variation in this method is about 20 pct. In the analyses of nonmetallic inclusions, aluminum-oxide determination was carried out according to Fischer's method, 3 as follows. A slice of sample was cut off and the surface was cleaned. It was dissolved in bromine-methanol. The solution was filtered and the residue was washed. The residue was fused with potassium bisulfate flux. Then it was dissolved in weak acid, and oxine solution was added. The aluminum oxinate was extracted with benzene. Finally, aluminum was determined absorptio-metrically. Aluminum nitride determination was carried out as follows. A slice of sample was cut off and the surface was cleaned. It was put in the distillation apparatus and decomposed with sodium hydroxide solution. The solution was distilled. Then ammonia was absorbed and

Jan 1, 1967

By FRED T. WILLIANS

INTRODUCTION. THE Park City mining-district is distinctively a camp of few properties, 5,000 acres, or one-third of the entire district, being under the management of but three companies. As a rule, the ore-bodies lie deep, with no outcrop, except where erosion has formed the deeper canyons and gulches. Ontario canyon exposed the famous Ontario ledge, and Woodside gulch showed the first ore of the Silver King Coalition mine. The Quincy ore-bodies were first brought to light in upper Empire canyon, and Thaynes canyon was instrumental in aiding the prospector during the early days of the camp. There are 22 shafts which have reached a depth of at least 500 ft., ten a depth of 1,000 ft., five a depth of 1,300 ft., and two a depth of 2,000 ft. The amount of lateral development has been proportionally extensive, including six long tunnels, four of which are in 3 miles, with a fifth now being driven. The Ontario lower drain-tunnel is now more than 4 miles long. The formations are sedimentary, dipping about 30° NW. and N., and traversed by many fissures, dikes, and faults. The principal ore-bodies are found associated either with the contact of the basal Ontario quartzite and the overlying limes, or on a quartzite stratum within the limes, or in the fissures, or along some of the porphyry dikes. The district covers the intersection of the Uintah and Wasatch ranges, which explains the existence of large folds and faults, and fissures of great length, width, and depth. In a general way, the geology of the district consists of a basal quartzite dome, which has been exposed by erosion at the Ontario property. The Ontario fissure lies entirely within this formation. Flanking this dome on the west, north, and east lie

Jun 1, 1911