Search Documents

By Joseph H. M. Beaty, Gust Bitsianes

Successful blast-furnace operation depends upon securing an optimum balance between a number of important variables. This balance will vary somewhat from furnace to furnace in the same plant and with raw materials available in different plants. It is difficult to isolate the effect of any one variable unless it has a rather pronounced effect upon the efficiency of operation. The physical properties of iron ore and coke are known to affect the process, yet it is difficult to set up any definite yardstick by which these differences can be appraised. In recent years, whenever practicable, operators have taken steps to obtain better control over the absolute size and uniformity of size of the ore and coke. The size and physical character of the stone, however, have received comparatively little attention, emphasis being placed upon chemical composition, fluxing efficiency, and action as a desulphurizing agent. Since the stone occupies only about 10 per cent of the volume of the stock column, its influence upon permeability is less than that of the ore and the coke. The large pieces now used have a tendency to roll to the center and thus increase the permeability of this part of the stock column. Smaller pieces would be more effective in promoting the permeability of denser portions of the stock. The size and physical properties of blastfurnace stone are important also for reasons best understood by considering the results obtained by the crushing and the sizing of iron ore. Crushing ore to about 2 in. at Provo, Utah, and to about I in. in Alabama produced material somewhat less permeable to gases, even though sized. In spite of some sacrifice in permeability, the efficiency of the process was improved by crushing and sizing the ore, as indicated by a substantial saving in fuel and increased output. This saving in fuel is due in large measure to more thorough reduction of ore in the upper part of the furnace and to a corresponding decrease in the amount of carbon consumed prematurely above the tuyeres by the reaction CO2 + C = 2CO - 70,080 B.t.u. [I] The physical properties of stone, its size and rate of calcination are important because they influence the rate at which CO2 is released and the completeness of calcination before reaching a level in the furnace where the temperature does not exceed 1050°C. (1920°F.). Briefly, carbon dioxide from the limestone or from the reduction of ore may cause premature corn bustion of carbon above the tuyeres. Assuming that 1000 Ib. of limestone is used per ton of pig iron, about 435 Ib. of CO2 will be liberated during calcination of a good grade of stone. If all this CO2 from the stone were to oxidize carbon prematurely, about 120 lb, would be consumed above the tuyeres in a heat-absorbing reaction. The amount of carbon thus consumed when a

Jan 1, 1943

By T. A. Lang

For permanent structure underground, where rock is not competent, support usually consists of concrete or reinforced concrete. However, temporary supports in the form of timber or steel are often needed during construc-tion. Although the history of rock bolting is relatively short—50 years— their use has become widespread in general engineering construction as well as mining. This profusely illustrated and detailed study covers a broad range in the field of rock belting: from the behavior of rock and bolts including rock properties, masses, and structure; mathematical formulae for rock bolt applications; through analysis of various operations and descriptions of the bolts themselves. Rock construction is one of the oldest of the engineering arts and its origin is lost in antiquity. From the days when early man decided that he wanted to improve the natural caves which he was using for shelter and protection or made a river crossing by placing rocks to form a ford or causeway, we have had structures made of rock. It is not too much to say that rock in situ as a structural material forms part of every major engineering undertaking. Rock bolting is one means whereby the inherently good characteristics of rock in situ are preserved and used to the best advantage and the bad characteristics ameliorated. In many cases the latter are accentuated by construction processes used. Rock bolting, as with other rock construction techniques, is only just beginning to emerge from being an art. Consequently, its theory and practice is still more descriptive than mathematical. ROCK BOLTING In underground excavations, where the rock is not competent, support is provided. For the permanent structure, this generally consists of concrete or reinforced concrete. However, support may be needed during construction before the concrete can be placed, and conventionally this consists of timber or steel support in the form of ribs, struts, and lagging. Alternatively, rock bolts may be used. Although their use dates back over 50 years, it is only in recent years that rock bolts have become widely used, not only in mining but in general engineering construction. A rock bolt is a steel bar which is inserted in a hole drilled in rock. The end away from the rock face has a device which permits it to be firmly an- chored in the hole and the projecting end is fitted with a plate which bears against the rock surface. The bolt is placed in tension between the anchor and the plate, thereby exerting a compressive force on the rock. The essential feature of a rock bolt is that it is placed in tension. This distinguishes it from anchor bars which are grouted into holes in rock, but which are not prestressed. The difference between an anchor bar and a rock bolt when the rock bolt is grouted in is analogous to the difference between the reinforcement in ordinary reinforced concrete and in prestressed reinforced concrete. The view that rock bolts only pin or nail blocks or slabs of rock which are loose to the sounder rock behind them is erroneous. Rock bolts are useful for this purpose and have been so used for a long time. However, the term rock bolting, as used here, means the designed use of rock bolts to reinforce and develop the rock around an excavation into a structural entity which can competently play its part in a structure such as a powerhouse or a mine installation. Rock bolts behave quite differently than steel ribs. They can be installed at the working face directly after blasting and within a short space of time can be exerting a stabilizing pressure on the loosened rock surface. This early installation not only partially restores loosened blocks of rock to their original unloosened positions, but also it prevents the gradual relaxation or loosening of the decompression zone behind the new rock face. In contrast, steel ribs generally use timber blocks, wedges, and lagging between the ribs and the irregular rock surface. The timber is relatively compressible, and loosened blocks of rock must move outwards an appreciable distance before any load builds up on the steel ribs. Also, the ribs may settle as the foot blocks and foundation become compressed. Hence, it may take several days or weeks before the rock has moved sufficiently to make the steel ribs carry an effective load.

Jan 1, 1961

By R. Ingerson

Bore surfaces of used guns commonly show a pattern of cracks in various degrees of development. It has been suggested that these cracks may aid erosion by providing channelways for the gases, eventually leading to the tearing out of blocks of metal. Under the general studies of gun erosion conducted at the Geophysical Laboratory it appeared desirable to consider this factor, and to determine the resistance to surface cracking offered by gun steel and by various other materials that might be used in the bores of guns. Method and Apparatus In order to make such a determination it is necessary to have (I) an arrangement in which the surface to be studied can be subjected to conditions similar to those in a gun with respect to temperature, pressure (developed by explosion gases), composition of the gases and length of time the surface is exposed to the gases; and (2) a specimen that can be examined readily after any number of shots, and then fired again, if necessary. The first of these conditions can be met by using an explosion vessel designed by H. S. Roberts of the Geophysical Laboratory. Fig I shows a cross-section of the apparatus. The "gun" G from which the charge is fired is made from the receiver of a caliber 0.30 army rifle, M1903, and the charges are prepared in caliber 0.30 cartridge cases. The test specimen S is held in place by a cone-shaped plug P and by a steel bridge B which is bolted to the outside of the explosion vessel on either side of the section shown. The plug, in turn, is held in place by a screw collar C. Maximum pressure is controlled by a brass rupture disk R. Part of the explosion gases flow past the two flat areas on S. Temperature and composition of gases, and the time before the rupture disk breaks, can be controlled by amount and kind of powder used, and pressure can be controlled by using rupture disks of different thickness. While the explosion vessel used was not designed so that temperature and pressure could be measured, in other vessels of closely similar size and shape containing proportionate charges of the same kind of powder as that used for standard testing procedure, values of 2700°K and 50,000 psi were obtained. Since the orifices past the flat areas on the plug are small compared to the rupture disk hole (I:I6), most of the gas goes out through the rupture disk when it breaks. The amount that goes by the plug depends on (I) the pressure attained before the rupture disk breaks and (2) the time it takes for this pressure to be built UP. The second condition (examination at will after any firing) is met by using for specimens short rods that have flat areas ground on opposite sides. These flat

Jan 1, 1949

By R. Ingerson

Bore surfaces of used guns commonly show a pattern of cracks in various degrees of development. It has been suggested that these cracks may aid erosion by providing channelways for the gases, eventually leading to the tearing out of blocks of metal. Under the general studies of gun erosion conducted at the Geophysical Laboratory it appeared desirable to consider this factor, and to determine the resistance to surface cracking offered by gun steel and by various other materials that might be used in the bores of guns. Method and Apparatus In order to make such a determination it is necessary to have (I) an arrangement in which the surface to be studied can be subjected to conditions similar to those in a gun with respect to temperature, pressure (developed by explosion gases), composition of the gases and length of time the surface is exposed to the gases; and (2) a specimen that can be examined readily after any number of shots, and then fired again, if necessary. The first of these conditions can be met by using an explosion vessel designed by H. S. Roberts of the Geophysical Laboratory. Fig I shows a cross-section of the apparatus. The "gun" G from which the charge is fired is made from the receiver of a caliber 0.30 army rifle, M1903, and the charges are prepared in caliber 0.30 cartridge cases. The test specimen S is held in place by a cone-shaped plug P and by a steel bridge B which is bolted to the outside of the explosion vessel on either side of the section shown. The plug, in turn, is held in place by a screw collar C. Maximum pressure is controlled by a brass rupture disk R. Part of the explosion gases flow past the two flat areas on S. Temperature and composition of gases, and the time before the rupture disk breaks, can be controlled by amount and kind of powder used, and pressure can be controlled by using rupture disks of different thickness. While the explosion vessel used was not designed so that temperature and pressure could be measured, in other vessels of closely similar size and shape containing proportionate charges of the same kind of powder as that used for standard testing procedure, values of 2700°K and 50,000 psi were obtained. Since the orifices past the flat areas on the plug are small compared to the rupture disk hole (I:I6), most of the gas goes out through the rupture disk when it breaks. The amount that goes by the plug depends on (I) the pressure attained before the rupture disk breaks and (2) the time it takes for this pressure to be built UP. The second condition (examination at will after any firing) is met by using for specimens short rods that have flat areas ground on opposite sides. These flat

Jan 1, 1949

By John A. Gann

The following investigation constitutes a brief réumé of the more important binary magnesium alloys from the standpoint of metallo-graphic technique, and the effect of heat treatment on structure and properties. The comparative newness of the subject justifies this procedure as a preface to a more detailed study of each individual series of alloys. The work was started with the idea of practical application in the industry rather than as a theoretical investigation. The alloy compositions studied were selected as those most likely to show whether heat treatment would produce beneficial results. Furthermore, it was considered satisfactory to use commercial 99.9 per cent. magnesium, the best commercial grade of alloying ingredients, and to limit the time of heat treatment at the expense of incomplete equilibrium. These facts must be kept in mind when examining the results obtained, and the conclusions drawn. Preparation of Alloys All melts were made in an oil-fired cast-steel pot, approximately 12 in. dia, by 12 in. deep. Approximately 15 lb. of flux and 50 lb. of magnesium were melted and the calculated amount of alloying metal was added. After thorough alloying and puddling, the metal was chill cast in a graphite mold with four 1/2 by 1/2 by 4 in. bars fed from a common sprue and runner. The next higher composition alloy in a given series was made by adding the calculated amount of metal to the heel from the preceding cast. The pot was thoroughly cleaned after each series and new flux then introduced, thus avoiding possible contamination from earlier melts. The percentage compositions given in Table 1 are the calculated values. While not all alloys were analyzed, enough were checked to indicate that the reported compositions are correct to a few tenths of one per cent. A more detailed description of the foundry methods employed has been given in a previous paper. 1

Jan 1, 1929

By John A. Gann

The following investigation constitutes a brief réumé of the more important binary magnesium alloys from the standpoint of metallo-graphic technique, and the effect of heat treatment on structure and properties. The comparative newness of the subject justifies this procedure as a preface to a more detailed study of each individual series of alloys. The work was started with the idea of practical application in the industry rather than as a theoretical investigation. The alloy compositions studied were selected as those most likely to show whether heat treatment would produce beneficial results. Furthermore, it was considered satisfactory to use commercial 99.9 per cent. magnesium, the best commercial grade of alloying ingredients, and to limit the time of heat treatment at the expense of incomplete equilibrium. These facts must be kept in mind when examining the results obtained, and the conclusions drawn. Preparation of Alloys All melts were made in an oil-fired cast-steel pot, approximately 12 in. dia, by 12 in. deep. Approximately 15 lb. of flux and 50 lb. of magnesium were melted and the calculated amount of alloying metal was added. After thorough alloying and puddling, the metal was chill cast in a graphite mold with four 1/2 by 1/2 by 4 in. bars fed from a common sprue and runner. The next higher composition alloy in a given series was made by adding the calculated amount of metal to the heel from the preceding cast. The pot was thoroughly cleaned after each series and new flux then introduced, thus avoiding possible contamination from earlier melts. The percentage compositions given in Table 1 are the calculated values. While not all alloys were analyzed, enough were checked to indicate that the reported compositions are correct to a few tenths of one per cent. A more detailed description of the foundry methods employed has been given in a previous paper. 1

Jan 1, 1929

By C. Kremer Bain

DURING the past several years of diamond drilling in Washington County, Mo., the St. Joseph Lead Co. has discovered a concentration of commercial lead-zinc ore at four different points within an area of 36 square miles. The largest and to date the most promising group of these orebodies is located in the Indian Creek area. It was considered to be of sufficient value to warrant development.

Jan 9, 1953

By Hugh M. Roberts

In the spring of 1915, then a 30-year old geologist in the employ of the E. J. Longyear Co., of Minneapolis, Minn., I accompanied prospectors to ex- amine outcrops of supposed nickel ore situated a mile or two in from the shore of a lake in the Kenora district of northwestern Ontario. The deposit proved to be bog iron ore containing traces of nickel. We were stormbound there for three days, a circumstance which gave rise to a tale that was told at our fire one night. It seems that Sandy and Jock, two prospectors, were crossing the bay of a large lake in a canoe. They were bucking headwinds; the waves grew higher. Jock called out from the stern, "Sandy, can ye na pray a little." Sandy pressed his knees a little closer into the bow and, between strokes of his paddle, sought for words, which came haltingly, "Save us this time . . . Oh Lord . . . and we promise . . ." when Jock, peering through the spray sang out, "I would na commit yourself, Sandy, I think I see lond ahead."

Jan 1, 1965

By Thomas B. Douglas

INSTRUMENTATION in the process industries can no longer be regarded as a convenience, but rather an absolute necessity. Although many chemical processes must already be conducted with instruments, every properly designed application of automatic process control will improve operation: 1) the product will be more uniform and of higher quality; 2) the manual labor saved will reduce cost; 3) uniformity of flow and uniform control of process will increase production; and 4) surges will be eliminated, making it possible to operate equipment near ultimate capacity at all times. Industrial instruments fall into two general classifications-those that measure and those that measure and control. The cement industry has been using instruments for a number of years, particularly in the burning process, primarily for indicating and recording. Automatic process control makes additional use of these instruments, and others, to control variables. Assisted by the instrument manufacturers, engineers at Ideal Cement CO. achieved considerable progress in determining how well the usual recording instruments could be made to control various phases of cement-making. The results of these experiments were used to make the new plant at Houston as wholly automatic as possible.

Jan 2, 1958

By C. H. Chou, Albert Sauveur

The following experiments were conducted in order to study the influence of the rate of cooling through and below solidification on the dendritic structure (macrostructure) and microstructure of some hypo-eutectoid steel. The steel selected was of commercial grade and had the following composition: C, 0.40 per cent.; Mn, 0.85; Si, 0.70; P, 0.099; S, 0.043. After melting in vacuum in an Arsem furnace, the various samples were allowed to solidify and to cool to room temperature as indicated in Fig. I. Samples were thus obtained representing all possible combinations of slow and fast cooling through the various ranges of temperatures indicated, namely: (I) zone of solidification or primary crystallization, (2) zone of granulation, and (3) zone of secondary crystallization. The location of the different temperature zones in the iron-carbon equilibrium diagram is shown in Fig. 2. The authors adopted Belaiew's notations. The designations of the various samples readily indicate their treatment, as will be apparent from Table 1. Sample SSS.—This sample was slowly solidified and cooled to room temperature in the crucible in which it was melted. The dendritic (macro) structure is shown in Fig. 3. The dendrites an: sharp and dis-

Jan 1, 1930

By J. Fred Johnson

MORE ORE is mined in the Bingham District than in any other mining district in Utah. In addition to the open-pit operations of the Utah Copper Co., there have been, many large underground mines. Until recent years the principal production was from the Jordan and Commercial limestones, but in the last eight years valuable ore deposits have been developed in the so-called alphabetical or "A," "B," "C," and "D" limestones, mainly by the U. S. Smelting, Refining & Mining Co. The value of these developments has led the company just mentioned to acquire large holdings in the district and within the last year to install at the Niagara shaft a hoist capable of going to a vertical depth of 4000 ft., or 1800 ft. deeper than the present lowest level. Ore from Bingham has been the chief factor in enabling the

Jan 1, 1934

By Robert J. Linney

IN the latter part of the year 1943, it was decided to experiment with diamond-drill blast holes in the Old Bed magnetite mine at the Mineville mines of the Republic Steel Corporation, in sections of the ore body where vertical dimensions were large and where development for sublevel bench stopes had already been done. Other possibilities of application for this drilling method were in the reclamation of old floors and pillars in the pitching folds of the Lower Old Bed ore body and in the reclamation of large vertical pillars in the " 21 " Bonanza-Joker ore body. The cross sections and views of the two ore bodies will show the conditions to which the diamond-drill method has been applied. The Lower Old Bed magnetite ore body is lenticular and dips approximately 30° toward the southwest and strikes generally southeast and northwest. An intensely folded structure, which pitches generally on an axis approximately at right angles to the strike, is continuous from the uppermost old workings down to the present bottom of the mine, and probably continues with depth. On successively lower levels this folded structure becomes greater in vertical dimensions and the two folds are closer together in a horizontal dimension. As shown in Fig. 1, this folded structure gives to parts of the ore body considerable vertical dimensions, which provide areas that were developed for sublevel bench stoping above a slushing drift, as shown in Fig. 2. It was in one of these previously developed sublevel bench stopes, No. 26 on the 1185-ft. level, that the diamond-drill blast-hole method was applied for mining the upper sublevel. The lower sublevel was underhand-bench-drilled to the finger raises of the scram drift below. The roof of this stoping area began to break and spall on the lower sublevel, causing the roof to become inclined. Along the hanging wall of the stope this reached an elevation about half way between the two sublevels. A smooth schistose seam in the hanging wall causes the ore to break away freely. Therefore, if bench mining had been carried on in the upper sublevel, a dangerous condition of poorly supported benches would have resulted. When the drillers were slashing across the sublevel to footwall and hanging wall to make a bench, spalling roof of the opening below would probably have carried away part of the bench, and would have left a dangerous place in which to continue underhand benching. A 6 by 8-ft. raise had been driven between the lower stope and the upper sublevel about 200 ft. from a manway. It was decided to use this raise for a starting cut and to arrange holes as shown in Fig. 3, so that a slot would be opened across the ore body between the footwall and hanging wall. This slot would then be used for the purpose of breaking into the ore; by blasting vertical rings of holes drilled at right angles to the axis of the pitching folds as nearly as possible. Layouts of this slot drilling and the rings adjacent are

Jan 1, 1945

By R. Casting, J. Philibert, and C. Crussard

APPARATUS described in this paper uses the properties of X-radiation, emitted by substances under electron bombardment, as a means of rapid chemical point analysis. The method is based upon the principles of emission X-ray spectrography pioneered by Moseley in 1913. A very finely focused beam of electrons—the electron probe—is projected on the surface of a sample, which has a very large area compared with the beam diameter, at the point where it is desired to know the chemical composition. The minute volume of the sample which is thus irradiated emits a complex X-ray spectrum consisting principally of the characteristic radiations of the elements present in the volume. Measurement of the wavelength and intensity of each component of this spectrum thus affords a simple method of determining the chemical identity and concentration of these elements. The volume of sample which is analyzed at each position of the beam is limited by the diffusion of electrons in the sample. For an accelerating potential of the electron beam of about 30 kv, which is a convenient value for producing the characteristic radiation, this diffusion extends over a diameter of about 1 µ normal to the beam, and about 2 µ in the direction of the beam. Thus a beam of 1 µ in diameter leads to a volume of about 2 µ in diameter being irradiated. The limits of the analyzed region are thus considerably smaller than those obtained by using spark or arc emission spectrometry, which must extend to about 50 µ at right angles to the beam, and those obtained in X-ray fluorescence analysis, where the penetration of the specimen is considerably greater. The apparatus itself consists of three main parts: an electron optical system. an X-ray spectrograph and an optical microscope. The electron opticai system consists of a tungsten cathode emitting the electrow and a pair of magnetic lenses which focus the electron beam on the specimen to be analyzed. The specimen is prepared in the usual way, as in optical micrography. The X-radiation, emitted at the focal spot where the electrons strike the sample, is analyzed with a curved crystal, Geiger-Müller counter, vacuum spectrograph. The light microscope, designed to observe the surface of the sample in the region to be analyzed, is provided with a reflecting objective placed on the axis of the second magnetic lens. Its magnification is X450. The quantitative determination of an element A in the analyzed region is made by measuring the intensity I, of a strong characteristic line of the element, as emitted from the sample, and then the intensity I (A) of this same line as emitted from a

Jan 1, 1958

By P. K. Koh

Chi phase (body-centered cubic, a = 8.89A) was found in as-cast 23 pct Cr-10 pct Mo-Fe alloy as well as in heat-treated 316, 316L, 317, and modified 446 stainless steels. Chi phase resembles sigma phase in its metastability, chemical composition, and brittleness. Microstructure and some of physical properties of chi phase were developed. MOLYBDENUM has been established as a desirable alloying element for the enhancement of corrosion resistance in Cr-Ni steels and creep and rupture strength in high temperature alloys. On the debit side, however, the molybdenum addition has been known to stimulate u formation. When the molybdenum-bearing steels were subjected to prolonged heating at elevated temperatures, losses of corrosion resistance and/or ductility have been observed. Andrews1,2 first found the existence of a new phase among the anodic FeC13 extracts from type 316 stainless steel solution treated and then reheated from 800" to 1100°C. This phase was designated x and was identified by diffraction patterns as of body-centered cubic structure with a value equal to 8.89? and similar to that of a manganese. He found that the x phase in this steel always coexisted with s phase, but failed to distinguish one from the other by metallographic technique. No definite conclusion was drawn regarding the equilibrium temperature ranges of these two phases. The appearance of Andrew's work recalled an un- explained structure observed several years ago at the Allegheny Ludlum Research Laboratories during the investigation of an experimental alloy containing 25 pct Cr, 10 pct Mo, and balance Fe. X-ray diffraction patterns on the as-cast material revealed the presence of a body-centered cubic phase having a lattice parameter of 8.89?. The structure was sufficiently similar to that of y chromium that for a time it was thought that the structure might be caused by the presence of some undissolved electrolytic chromium particles. The alloy as-cast was so brittle that it shattered after the slightest hot reduction by hammer cogging. This paper gives the results of some metallographic and X-ray diffraction studies on x phase as found in several experimental alloys as well as a few molybdenum-bearing commercial stainless steels. The analyses of materials studied were as shown in Table I. Experimental Procedure Metallography: Solid specimens were polished mechanically and etched in boiling 50 pct HC1 solution in order to best delineate x and s phases in the alloys studied. X-Ray Diffraction: The difficulty of satisfactorily developing diffraction lines for s phase in solid specimens has been previously reported by Bindari, Koh, and Zmeskal.V or this reason all specimens used in this investigation were subjected to anodic

Jan 1, 1954

By Alec M. Crowell, J. W. Sanders

While the production of crude oil and condensate in South Arkansas increased only 1.7 per cent over the 1940 figure, complete utilization of gas produced with the oil and condensate, and heretofore wasted, was beginning to be evidenced. There were 26,229,264 bbl. of oil and condensate produced in South Arkansas during 1941, as against 25,790,380 bbl. for the year 1940. (Fig. I.) Since 1936, deep producing sands have been discovered in 18 fields and during that period only 40 per cent of the total state production has come from Upper Cretaceous formations while 60 per cent came from the Lower Cretaceous and Jurassic formations. The gas produced with crude oil and condensate from the latter formation contains large quantities of hydrogen sulphide, the maximum being 6900 grains per 100 cu. ft. in the Patton pool of Lafayette County. Gas Utilization During the latter part of 1940 and the early part of 1941, pilot plants were placed in operation to determine whether the hydrogen sulphide and deleterious material in South Arkansas gases could be removed economically. The Federal Government desired to build a large aluminum plant in the Ouachita Valley and was seeking cheap fuel for the generation of electricity. The fact that the gases were produced with appreciable quantities of crude oil and condensate made it available at a very low price, since the state's conservation law prohibits the flaring of any gas. As a result of these experiments the first large-scale unit for the processing of gases containing hydrogen sulphide was placed in operation on Sept. I, 1941. The plant is in the Magnolia oil field, Columbia County. It processes residue gas from the Shell Oil Company's gasoline plant in that field and also raw gas from the Village field, 6 miles east of the Magnolia field. The gas entering the desulphuri-zation unit is laden with approximately 1400 grains of hydrogen sulphide per 100 cu. ft. and is stripped to a content of 4 grains per 100 cu. ft. The capacity of the plant is 15 million cu. ft. of gas treated daily under a pressure of 160 lb. per sq. in. The cost of treatment, exclusive of depreciation, is appreciably less than I per 1000 cubic feet. Two other plants of much greater capacity have been announced and priorities have been granted, which should bring the total amount of gas treated to 150 million cu. ft. daily. The gas to be treated will have a maximum hydrogen sulphide content of 4500 grains per 100 cu. ft. and will be processed under a pressure of 600 lb. per sq. in. These developments are something entirely new in field practice for the industry. The fact that this heretofore wasted gas is available at very low cost has led to the location of some eight war industries within the state, in addition to the alu-minum plant. Recovery OF Sulphur The Susearch Corporation and the Southern Acid and Sulphur Co. placed in operation during 1941 pilot plants to de-

Jan 1, 1942

By Alec M. Crowell, J. W. Sanders

While the production of crude oil and condensate in South Arkansas increased only 1.7 per cent over the 1940 figure, complete utilization of gas produced with the oil and condensate, and heretofore wasted, was beginning to be evidenced. There were 26,229,264 bbl. of oil and condensate produced in South Arkansas during 1941, as against 25,790,380 bbl. for the year 1940. (Fig. I.) Since 1936, deep producing sands have been discovered in 18 fields and during that period only 40 per cent of the total state production has come from Upper Cretaceous formations while 60 per cent came from the Lower Cretaceous and Jurassic formations. The gas produced with crude oil and condensate from the latter formation contains large quantities of hydrogen sulphide, the maximum being 6900 grains per 100 cu. ft. in the Patton pool of Lafayette County. Gas Utilization During the latter part of 1940 and the early part of 1941, pilot plants were placed in operation to determine whether the hydrogen sulphide and deleterious material in South Arkansas gases could be removed economically. The Federal Government desired to build a large aluminum plant in the Ouachita Valley and was seeking cheap fuel for the generation of electricity. The fact that the gases were produced with appreciable quantities of crude oil and condensate made it available at a very low price, since the state's conservation law prohibits the flaring of any gas. As a result of these experiments the first large-scale unit for the processing of gases containing hydrogen sulphide was placed in operation on Sept. I, 1941. The plant is in the Magnolia oil field, Columbia County. It processes residue gas from the Shell Oil Company's gasoline plant in that field and also raw gas from the Village field, 6 miles east of the Magnolia field. The gas entering the desulphuri-zation unit is laden with approximately 1400 grains of hydrogen sulphide per 100 cu. ft. and is stripped to a content of 4 grains per 100 cu. ft. The capacity of the plant is 15 million cu. ft. of gas treated daily under a pressure of 160 lb. per sq. in. The cost of treatment, exclusive of depreciation, is appreciably less than I per 1000 cubic feet. Two other plants of much greater capacity have been announced and priorities have been granted, which should bring the total amount of gas treated to 150 million cu. ft. daily. The gas to be treated will have a maximum hydrogen sulphide content of 4500 grains per 100 cu. ft. and will be processed under a pressure of 600 lb. per sq. in. These developments are something entirely new in field practice for the industry. The fact that this heretofore wasted gas is available at very low cost has led to the location of some eight war industries within the state, in addition to the alu-minum plant. Recovery OF Sulphur The Susearch Corporation and the Southern Acid and Sulphur Co. placed in operation during 1941 pilot plants to de-

Jan 1, 1942

By Ralph E. Esarey, George V. Cohee

In Indiana, 349 wells were drilled for oil and gas in the year 1942. Of this number, 125 oil wells and 21 gas wells were successfully completed and 203 were dry holes. Drilling activity declined 37 per cent as compared with that of the year 1941. This reduction was brought about largely by Federal Conservation Order M-68, restricting drilling to one well on 40 acres, in order to save steel. This Order was later supplemented to permit closer spacing of wells drilled to sandstone formations in southwestern Indiana. Most of the drilling in 1942 was in the southwestern part of the state. Posey County ranked first, with 94 completions and 44 producers; Gibson County, second, with 77 completions and 38 producing oil wells and 2 gas wells. There were 58 drilling operations in the state at the end of the year. During 1942 a total of 589,734 ft. of hole was drilled, of which 231,702 ft. was wildcat footage. The total initial production of the oil wells completed was 9974 bbl. and of the gas wells, 11,148,000 cu. ft. (Table 2). Of the 349 wells completed, 122 were wildcat wells (Table 3); 26 were completed as oil wells; 17 were extensions to proven fields and 9 discovered new pools. Posey County was foremost in wildcat drilling, with 37 wells completed (Table 6). Thirty-five per cent of the wells drilled in 1942 were wildcat, as compared with 25.5 per cent in 1941. It is anticipated that the percentage of wildcat wells drilled in 1943 will be greater, although the total number ol ,wells drilled in the state will probably be less. The new discoveries in Indiana in I942 were, for the most part, one-well pools in the southwestern part—in Posey, Gibson and Spencer Counties (Table 4). Most of the development in pools took place in the . Hazelton and Kirksville pools in Gibson County, Mr. Vernon pool in Posey County and the Vernon Heights pool in Vander-burgh County. Deeper production was obtained from the Osage limestone in the Hazelton pool at a depth of 2402 ft., 650 ft. below the productive McClosky limestone. The well had an initial production of 140 barrels. Extensions to 17 pools in the southwestern part of the state were successfully completed (Table 5). An interesting development during 1942 was new production from the Devonian limestone in the Dodds Bridge pool, Sullivan County. The Ohio Oil Co. deepened one of its wells, which had been producing from a shallow sand, to the,Devonian, and it was completed for an initial production of 77 bbl. Five other Devonian producing wells were completed in that area. Crude-oil production in Indiana in 1942 was 6,609,000 bbl. (Table I). The Griffin field, Gibson and Posey Counties, which produced approximately 3,550,000 bbl., accounted for more than half of the state's production. The Mt, Vernon and New Harmony fields were next in importance of production, with 684,000 and 523,000 bbl., respectively. The price of crude oil was $1.22 a barrel for the old

Jan 1, 1943

By George V. Cohee, Ralph E. Esarey

In Indiana, 349 wells were drilled for oil and gas in the year 1942. Of this number, 125 oil wells and 21 gas wells were successfully completed and 203 were dry holes. Drilling activity declined 37 per cent as compared with that of the year 1941. This reduction was brought about largely by Federal Conservation Order M-68, restricting drilling to one well on 40 acres, in order to save steel. This Order was later supplemented to permit closer spacing of wells drilled to sandstone formations in southwestern Indiana. Most of the drilling in 1942 was in the southwestern part of the state. Posey County ranked first, with 94 completions and 44 producers; Gibson County, second, with 77 completions and 38 producing oil wells and 2 gas wells. There were 58 drilling operations in the state at the end of the year. During 1942 a total of 589,734 ft. of hole was drilled, of which 231,702 ft. was wildcat footage. The total initial production of the oil wells completed was 9974 bbl. and of the gas wells, 11,148,000 cu. ft. (Table 2). Of the 349 wells completed, 122 were wildcat wells (Table 3); 26 were completed as oil wells; 17 were extensions to proven fields and 9 discovered new pools. Posey County was foremost in wildcat drilling, with 37 wells completed (Table 6). Thirty-five per cent of the wells drilled in 1942 were wildcat, as compared with 25.5 per cent in 1941. It is anticipated that the percentage of wildcat wells drilled in 1943 will be greater, although the total number ol ,wells drilled in the state will probably be less. The new discoveries in Indiana in I942 were, for the most part, one-well pools in the southwestern part—in Posey, Gibson and Spencer Counties (Table 4). Most of the development in pools took place in the . Hazelton and Kirksville pools in Gibson County, Mr. Vernon pool in Posey County and the Vernon Heights pool in Vander-burgh County. Deeper production was obtained from the Osage limestone in the Hazelton pool at a depth of 2402 ft., 650 ft. below the productive McClosky limestone. The well had an initial production of 140 barrels. Extensions to 17 pools in the southwestern part of the state were successfully completed (Table 5). An interesting development during 1942 was new production from the Devonian limestone in the Dodds Bridge pool, Sullivan County. The Ohio Oil Co. deepened one of its wells, which had been producing from a shallow sand, to the,Devonian, and it was completed for an initial production of 77 bbl. Five other Devonian producing wells were completed in that area. Crude-oil production in Indiana in 1942 was 6,609,000 bbl. (Table I). The Griffin field, Gibson and Posey Counties, which produced approximately 3,550,000 bbl., accounted for more than half of the state's production. The Mt, Vernon and New Harmony fields were next in importance of production, with 684,000 and 523,000 bbl., respectively. The price of crude oil was $1.22 a barrel for the old

Jan 1, 1943

By W. Tempelaar Lietz

The Ten Section oil field is located in the San Joaquin Valley in Kern County, California. about 12 miles southwest of Bakersfield in Township 30 South, Ranges 25 and 26 East. The accumulation is in a low relief anticlinal dome and has a productive area of approximately 2,200 acres. Discovered in 1936 as a result of seismic work, it was the first field on the floor of the Valley to obtain production. It had a small primary gas cap, and since its inception has been produced by depletion with controlled withdrawal from the gas cap to minimize blowthrough. STRUCTURE AND STRATIGRAPHY The Ten Section structure is an elongated anticlinal dome with flank dips of only about 7 degrees. A map of the field, now fully developed, and a composite log are shown in Figs. 1 and 2. Contours shown on the map are on the top of the first zone, or Marker XA as indicated on the composite log. As shown, the field has a productive closure of only some 350 feet, and there apparently is no faulting in the reservoir. The productive measures in Ten Section are of Upper Miocene age and are known as the Stevens sand. They contain thin, irregular shale or siltstone streaks which vary considerably in stratigraphic position and thickness and apparently are rather discontinuous. As a result, individual sands and shales cannot be correlated over any appreciable area, which makes it difficult to subdivide the sand body into separate zones which are distinct throughout the field. However, there are two fairly persistent siltstone bodies that at the time of development were considered to divide the productive measures into three - zones. The first, or uppermost zone is productive over the entire field and has an average thickness of 180 feet, of which some 65 per cent is sand. It had a primary. gas cap in the crestal area with an areal extent of 930 acres. The second zone has a productive area somewhat smaller than the first zone, but it did not have any original gas cap. It has an average thickness of about 360 feet, of which 55 per cent is sand. The third zone has a very limited areal extent and a maximum productive thickness of 100 feet, of which 80 per cent is sand. Recently, a deeper oil accumulation, termed the "53" sand, was discovered, but it is not discussed in this analysis. In the first and second zones the water table was at 7,980 feet subsea, while in the third zone it was at 8,080 feet subsea. RESERVOIR CHARACTERISTICS Sand Characteristics The Stevens sand in Ten Section is hard and well consolidated, and numerous wells were cored for core analysis. Core data on four representative wells are shown, plotted beside the electric logs in Figs. 3 to 6. The average porosity is 20 per cent, with porosities ranging from 15 to 30 per cent. It is estimated, from cores taken with oil base muds, that the interstitial water content is about 40 per cent. The average weighted permeability is approximately 140, with measured permeabilities ranging from 10 to 3,000 md. As might be expected with practically no correlation of individual sand

Jan 1, 1949

By W. Tempelaar Lietz

The Ten Section oil field is located in the San Joaquin Valley in Kern County, California. about 12 miles southwest of Bakersfield in Township 30 South, Ranges 25 and 26 East. The accumulation is in a low relief anticlinal dome and has a productive area of approximately 2,200 acres. Discovered in 1936 as a result of seismic work, it was the first field on the floor of the Valley to obtain production. It had a small primary gas cap, and since its inception has been produced by depletion with controlled withdrawal from the gas cap to minimize blowthrough. STRUCTURE AND STRATIGRAPHY The Ten Section structure is an elongated anticlinal dome with flank dips of only about 7 degrees. A map of the field, now fully developed, and a composite log are shown in Figs. 1 and 2. Contours shown on the map are on the top of the first zone, or Marker XA as indicated on the composite log. As shown, the field has a productive closure of only some 350 feet, and there apparently is no faulting in the reservoir. The productive measures in Ten Section are of Upper Miocene age and are known as the Stevens sand. They contain thin, irregular shale or siltstone streaks which vary considerably in stratigraphic position and thickness and apparently are rather discontinuous. As a result, individual sands and shales cannot be correlated over any appreciable area, which makes it difficult to subdivide the sand body into separate zones which are distinct throughout the field. However, there are two fairly persistent siltstone bodies that at the time of development were considered to divide the productive measures into three - zones. The first, or uppermost zone is productive over the entire field and has an average thickness of 180 feet, of which some 65 per cent is sand. It had a primary. gas cap in the crestal area with an areal extent of 930 acres. The second zone has a productive area somewhat smaller than the first zone, but it did not have any original gas cap. It has an average thickness of about 360 feet, of which 55 per cent is sand. The third zone has a very limited areal extent and a maximum productive thickness of 100 feet, of which 80 per cent is sand. Recently, a deeper oil accumulation, termed the "53" sand, was discovered, but it is not discussed in this analysis. In the first and second zones the water table was at 7,980 feet subsea, while in the third zone it was at 8,080 feet subsea. RESERVOIR CHARACTERISTICS Sand Characteristics The Stevens sand in Ten Section is hard and well consolidated, and numerous wells were cored for core analysis. Core data on four representative wells are shown, plotted beside the electric logs in Figs. 3 to 6. The average porosity is 20 per cent, with porosities ranging from 15 to 30 per cent. It is estimated, from cores taken with oil base muds, that the interstitial water content is about 40 per cent. The average weighted permeability is approximately 140, with measured permeabilities ranging from 10 to 3,000 md. As might be expected with practically no correlation of individual sand

Jan 1, 1949