Search Documents

By J. A. Burkhardt

Field measurements and theoretical studies have been made of pressure surges—momentary variations in fluid pressure—produced by movement of pipe in mud-filled boreholes. Pressure measurements were recorded by five pressure gauges located at various positions in the borehole. An important positive pressure peak was found to occur as the casing moved with maximum velocity. Important negative peaks were found as the casing was lifted from the slips and as brakes were applied to stop pipe movement. A rigorously formulated theory has successfully predicted the sequence and magnitudes of these positive and negative surges and has established a basis for understanding how they occur. Both the measurements and theory indicate that the most important pressure surge is usually due to viscous drag of the flowing mud. The theory of viscous-drag pressure surges has been approximated by simplified graphs and calculation procedures to facilitate ready use in field operations. Comparison of measured results with those predicted by the simplified theory shows that the magnitude of this surge can be predicted accurately. INTRODUCTION It is widely recognized that raising or lowering pipe in a fluid-filled borehole produces momentary variations in fluid pressure, commonly called pressure surges. Both negative (or "swabbing") surges and positive (or "fracturing") surges may occur. In 1934, Cannon1 measured the negative surges and showed that they could be large enough to cause flow of formation fluids into the well-bore and, in extreme cases, lead to blowout conditions. Later, Coins2 measured the positive surges associated with lowering pipe. His results and subsequent field operations strikingly demonstrated that pressure surges could be an important factor in some cases of lost returns. In addition, although the evidence is less clear than in the case of blowouts and lost returns, other investigators 3, 4 feel that pressure surges probably play a part in many instances of minor gas cutting, salt-water flow and other hole trouble. The importance of pressure surges in drilling operations led naturally to attempts to explain the physical causes, nature and magnitude of the surges. Cardwell5 was the first to publish a theory which allowed the quantitative prediction of momentary pressure variations. He assumed that the drilling fluid was a 300-cp Newtonian fluid in turbulent flow. Most field muds have a considerably lower viscosity and are generally believed to be Bingham plastic in nature.6 However, card-well's results were useful because they were presented in a form convenient for field use and, in some cases, gave a reasonably accurate predicted value for the maximum pressure surge. Subsequently, Ormsby7 published a more comprehensive theory of pressure surges. He discussed both laminar and turbulent flow and considered the theory of mud-bypass devices for reducing pressure surges. As a consequence of his more rigorous approach, his results were more accurate but more complex and difficult to use. Further, both Ormsby and Cardwell considered only the pressure surge arising from viscous drag of the moving mud. Clark later published idealized graphs of surges and presented equations for predicting their magnitudes. In addition to pressure variations arising from viscous drag, he considered those caused by inertial effects. His theory was in this respect more complete than those of Cardwell and Ormsby, although he did not discuss pressures due to breaking of the gel. Furthermore, his equations, while not exceptionally complicated, were too complex for ready use at a drilling location. One difficulty common to all three theories is that none was tested rigorously by direct comparison with measured pressure surges. Their accuracy, therefore, could, not be demonstrated. Further, the two theories based on most realistic assumptions (Ormsby and Clark) required the solution of one or more rather complex algebraic equations. The research described in this paper was undertaken to supplement that described and to overcome some of the difficulties noted. It seemed obvious that a fully satisfactory study of pressure surges should encompass three main phases. 1. A valid theory useful in all field situations must be developed. This theory must be based upon realistic assumptions, must be formulated rigorously and should lead to clear concepts whereby the nature of pressure surges can be easily understood. 2. The theory, however complex and involved, ultimately must be presented in simplified form for convenient field use. This may involve extensive machine computations and the use of figures and empirical equations. 3. The accuracy of the simplified equations must be established by comparing measured pressure surges with those predicted by the theory. These must agree both in their characteristic nature and in magnitude. 'This means that careful measurements of surges occurring in actual field operations must be made.

By W. G. Matteson

The Gulf Coastal plain of the southern United States is that area bordering for a large part, the Gulf of Mexico and extending inland and northward to the main interior highland region. It is more or less V-shaped and includes the States of Florida, extreme southern Alabama, all .of Mississippi and Louisiana, the eastern and southern half of Arkansas, and the eastern, southeastern, and southern portions of Texas. While the contents of this paper apply to. the Gulf Coastal plain in general, they are intended to refer more specifically to that portion of the plain included between the 90th and 97th meridians, and the 29th and 33d parallels, an area that may be described geographically as comprising western Mississippi, all of Louisiana, part of eastern and all of south-eastern Texas. It is within this area that numerous and prolific oil pools have been developed during the last 17 years.

Jan 2, 1918

By James B. Cathcart

The potash mine of the International Minerals and Chemical Corp. is about 18 miles east of Carlsbad, New Mexico, in sec 1 and 12, T 22 S, R 29 E, N.M.P.M. Potash is produced from two zones in the Salado formation of late Permian age. The lower zone, consisting of a mixture of sylvite (KCI) and halite (NaCl), lies at a depth of about 900 ft, and the upper zone, in which the principal potassium mineral is langbeinite (K2SO4 2MgSO4), lies at a depth of about 800 ft. Because of the plastic nature of the material, fractures in the Salado formation are extremely rare and have been noted only on the 800 ft level of the International mine. The open fracture described below is almost unique. Only one other open fracture has been noted, and it was on a working face in the same general area as the one described, but was destroyed before the writer had a chance to examine it. According to J. E. Tong, foreman on the 800 level, this fracture was similar to, but smaller than, the one herein described. The saline strata are nearly flat-lying and comprise interbedded layers of halite, anhydrite (CaSO4), and poly-halite (2CaSO4.MgS04.K2SO4-2H2O), with halite predominating. The halite layers contain local concentrations of sylvite, carnallite (KC1.MgCl2.6H2O), and langbeinite. The principal marker in the potash mines area is a bed of anhydrite about 8 ft thick, and 70 ft below the 800 level. This bed contains varying amounts of polyhalite, and locally a few blebs of sylvite. Two principal marker beds are present over most of the 800 level. The lower is the "Middle Salt Marker," a bed of bright-orange halite, which ranges in thickness from a knife-edge to about 0.6 ft, and is usually bounded above and below by thin seams of green or reddish-brown clay. In langbeinite-rich areas, this marker usually contains abundant blebs of langbeinite. The upper of the two principal markers is a green clay seam, containing abundant halite, which ranges in thickness from 0.1 to about 0.5 ft. It is 2 to slightly more than 5 ft above the Middle Salt Marker. No langbeinite of minable grade is found above this clay, and it

Jan 1, 1950

THE IRON HUNTER. By Chase S. Osborn, pp. 316, Ills. 10. The MacMillan Company, New York. 1919. An autobiography, the story of a Hoosier boy who fought his way to manhood and power through early misfortune and poverty, from street urchin and newsboy, to editor and author; from lumberjack and dock walloper to statesman and Governor of Michigan. The reader has the measure of the man in the first chapter, a dramatic recital of how the fighting boy editor cleaned up a lawless mining camp of 40 years ago. The thread of the narrative is the author's life-long devotion to outdoor living, ex-ploration and travel. Residing in Sault de Sainte Marie, Mich., in the heart of the Lake Superior country, he took his delight and, incidentally, found his fortune in prospecting the north woods for iron ore; eventually, extending his travels to the continents and many of the islands of the world, he discovered what, he believes-to be a great iron range in Madagascar. In this book there is plenty of anecdote, a great deal of wholesome social and po¬litical philosophy and some interesting sidelights on the characters of some of the author's prominent contemporaries in the political life of Michigan. The style is direct and animated, flavored and illuminated with the vernacular of Hoosierdom and the woods country of the North. The author levies on the vocabulary of the sciences and the classics for many a noun and adjective and, with Rooseveltian license, now and then coins a word. The reader's interest will be gripped from cover to cover, albeit he may occasionally need a dictionary. R. C. A.

Jan 11, 1919

By E. A. Gulbransen, K. F. Andrew

Thermodynamic information on the solubility of hydrogen in exothermic metals is limited. Thus, the overall solubility decreased as the temperature rose, which suggests the heat of solution of hydrogen in the metal is negative; yet the terminal solubility in the metal phase increased, which suggests an endothermic reaction. A thermodynamic analysis, therefore, was made of the several equilibria involved when hydrogen dissolved in the metal. Equations were derived expressing the solubility, terminal solubility, and decomposition pressures of hydrogen in terms of the heat, entropy, and free energy of solution of hydrogen in the given phase. The relations between the thermodynamic functions for the a-zirconium and 8-hydride phase were developed. The thermodynamic quantities were determined experimentally by the measurement of the decomposition pressures over a broad composition and temperature range. Two new methods of analyzing the experimental data were developed for determination of the terminal solubility. STUDIES', ' of the impact strength of zirconium at room temperature indicated that small quantities of hydrogen, of the order of 10 parts per million, embrittles the metal. Micrographic' and X-ray diffraction' studies showed this embrittlement to result from the precipitation of a second phase upon slow cooling. These studies suggested that the terminal solubility of hydrogen in the metal phase increased with increase of temperature. This behavior appeared to contradict the effect of temperature on exothermic hydrogen occluders such as zirconium. For these metals, the solubility of hydrogen should decrease with increase of temperature. Before these facts could be understood, a thorough analysis of the several equilibria was essential. It was the purpose of this paper to consider the several equilibria involved when hydrogen was reacted with zirconium from both the theoretical and experimental points of view. Since the overall solubility of hydrogen in the metal has been considered by a number of workers, it was proposed to study the composition range 0 to 6 atomic pct H in detail. Literature Schwartz and Mallett' determined the terminal solubilities of hydrogen in the metallic phase from diffusion studies. They extrapolated concentration-penetration curves to the boundary between the solid solution phase and the hydride phase at the surface. Their results showed values of 2.6 atomic pct at 400°C and 5.2 atomic pct at 500°C. Extrapolations of the data to room temperature suggested very low values for the terminal solubilities. This study confirmed the hydrogen embrittlement results and indicated that the terminal solubilities increased as the temperature was raised. The solution of hydrogen in zirconium over the complete concentration range was studied by Hall, Martin, and Rees3 and by others. The results showed that hydrogen was absorbed up to a maximum composition of 66 atomic pct or ZrH This composition represented the t-hydride phase. The maximum amount of hydrogen absorbed increased with pressure and decreased with temperature. Due to this temperature behavior, zirconium was classed as an exothermic occluder." In 1930 Hägg studied the crystal structures of the Zr-H alloys over a broad composition range. Four hydride phases were found. However, the range of homogeneity of the several phases was not studied. Gulbransen and Andrew" recently studied the phase diagram of this system by X-ray diffraction methods and by a thermodynamic method based on decomposition pressure measurements. The results showed that only two hydride phases existed for low temperatures, the 6 and the .-phases of Hagg.' Both phases had broad regions of homogeneity. The lower limit of the two-phase region of a and d-phases suggested a terminal solubility of 4 atomic pct at 500°C. This value was in agreement with the results of Schwartz and Mallett.' To avoid hydrogen embrittlement at low temperatures, it was necessary to heat the metal in high vacuum at elevated temperatures. To choose the conditions of temperature and high vacuum, it was

Jan 1, 1956

By J. A. Singmaster

IT will perhaps be wise to define my terms in begin-ning to talk about my subject, especially so where the popular and commercial terminology are as con-fused as they are in the case of zinc. While our French friends know zinc by its true name, and we find Balzac, Daudet, and other literary celebrities using it correctly in their novels, it is quite the contrary in English, particularly here in America. The quotation of a definition for zinc recently appearing in one of our leading technical magazines, "zinc is the place where they wash the dishes," will emphasize the difference. Zinc suffered in the first place by becoming an article of commerce long after its alloys with copper were in common use under the name of brass. Then again, when the art of zinc coating iron and steel objects was commercialized, we called it galvanizing, which is really a meaningless term. The French and Germans use the obvious terms-zinguerie and verzinken-for the opera-tion. Since these two uses of zinc, brass making and galvanizing, have been by far the largest consumers of zinc, is it any wonder that the popular knowledge of zinc is as vague as it is? In fact, since the disappear-ance of the sheet of zinc along with the parlor stove, the zinc-lined bath tub and refrigerator, there has been little popular contact in this country with the undis-guised metal zinc. On the Continent, where zinc has been used for over a hundred years under its real name, particularly for roofing and building purposes, the situ-ation is quite different. It is quite refreshing to turn for a moment to the contrast offered by my friend, Dr. Merica's specialty, nickel. They put 2 or 3 per cent of it into steel, and we have nickel-steel, or a larger amount into an alloy, and we have nickel-silver. To be sure there is no silver there, but what need that matter, nickel is used in the alloy and is first in the name. They plate with nickel and call it nickel-plating, no galvanizing about that. And, finally, they take that noble coin which admits us daily to underground New York, composed of three parts of copper and one part nickel, and get away with nickel as its popular name.

Jan 6, 1927

By M. J. Sinnott

WITH the advent of nodular iron as an engineering material, considerable interest has been shown in developing this material for various applications. Generally the strength, hardness, or ductility are the more common properties used for design purposes but occasionally applications involving a knowledge of the thermal conductivity of the material is required. A search of the literature showed, rather surprisingly, that relatively little work has been done on this property for all types of cast iron. Insufficient data are available on thermal and electrical conductivities to develop the Weidemann-Franz ratio, or the Lorentz relationship, for estimation purposes. There are no data on nodular irons and the published data on malleable irons are quite sketchy. For these reasons the conductivity of the group of nodular irons listed in Table I were measured. Irons I to IV were made in such a fashion as to maintain the carbon and alloy content essentially the same while varying the silicon content. Test specimens were cut from the mid-section of 4-in. keel castings. Iron V is a commercial casting of nodular iron. The test specimen of this iron was cut from the center of a large cast billet 3x10x26 in. All alloys were tested in the as-cast condition. A microstructural examination showed that each iron had spheroidal graphite but the size and distribution varied with the silicon content of the iron. The spheroid size decreased while the number of graphite nodules increased as the silicon content of the iron was increased. The matrix structures of each iron consisted of pearlite and ferrite with the proportions varying from predominantly pearlite in the low-silicon iron to mostly ferrite in the high-silicon iron. The commercial heat, iron V, was predominantly pearlite probably because of its higher manganese and phosphorus content. Two methods for measuring the thermal conductivity were used. The first was a modification of the techniques described by Powell and Hickman and Van Dusen and Shelton,² the second method was a simpler technique described by Jakob and Hawkins." Since the agreement of both methods as tested on two sets of duplicate samples was excellent, the simpler experimental technique was used. The results of the measurements are given in Table II along with a summary of the microstructural constituents. These conductivity data indicate that as the percentage of silicon increases there is a corresponding decrease in the thermal conductivity even though the structure is changing from pearlitic to ferritic. Such a change in microstructure is usually accompanied by an increase in conductivity. A third factor involved in the behavior of these irons is the size and distribution of the graphite nodules. The relative amounts of graphite do not change greatly but the size and distribution do. Generally graphite improves the conductivity but in the present case such an effect is probably masked by the alloying effect from the silicon and its dispersion through the matrix. The thermal conductivity of the nodular irons studied is less than that of regular foundry irons by some 10 to 30 pct and is less than that of regular malleable irons.' The cause of the decreased conductivity is probably the more highly alloyed fer-rites obtained in these irons and the changed mode of distribution of the graphite as compared to the regular foundry irons. References R. W. Powell and M. J. Hickman: Journal Iron and Steel Inst. (1946) 154, No. 2, p. 99. 'M. S. Van Dusen and S. M. Shelton: U. S. Bur. Standards Journal of Research, RP668 (1934) 12, p. 429. ³M. Jakob and G. A. Hawkins: Elements of Heat Transfer and Insulation. 2nd Ed. (1950) New York. John Wiley and Sons. ' J. W. Donaldson: Journal Iron and Steel Inst. (1933) 128, No. 2, p. 255.

Jan 1, 1954

By Lawrence Wright

ON the steep slopes of the Kootenays, 15 to 20 miles south of Nelson, B. C., are a number of ore occurrences (Fig. 1). One that has many features of mining and geological interest is the Ymir Yankee Girl Gold Mines Limited. Discovery of this property was made in 1899 at an outcrop on the hillside, some 2500 ft. above the village of Ymir. This proved to be a branch vein 20 ft. long leading to two main veins, the Yankee Girl and the Spur (Fig. 5). The ore pattern as now delimited shows a remarkable increase in ore area with depth below the outcrop. This recent development is of interest particularly in view of the fact that the property was nearly con-demned, professionally. Another interesting feature, which has a bearing upon its history, is the persistent excess of tonnage produced from period to period over visible reserves. This is not ascribed to lagging mine development, but to detailed vein characteristics, which we will endeavor to make clear by giving a description of the veins and their surroundings.

Jan 1, 1938

By David B. Reger

Exploration for new pools of gas in the Oriskany sand and continued exploitation of areas already known to be productive in that sand were the main features of petroleum activity in West Virginia during 1938. To a considerable extent the exploration program resulted in failure, but the extension of former areas was eminently successful. Throughout the state, in general, less drilling was done than in 1937. According to the West Virginia Department of Mines, only 631 permits to drill were issued, as compared to 1034 in 1937. The account of operations, as reported by trade journals and other sources, shows that 766 wells were drilled, resulting in 131 oil wells with 1609 bbl. of daily production; 484 gas wells with 1,232,216,000 cu. ft. of daily open flow; and 151 dry holes. Several discoveries indicate new pools of oil and gas; and several extensions of old gas pools have been made. In spite of a decreased number of total wells, the figures for new gas and oil are both larger than in 1937. The new oil average is 12.3 bbl. per well per day; the gas average is 2,545,900 cu. ft. per well per day, the ratio of dry holes to completions is 19.71 per cent. No general attempt was made to discover new pools of oil. A continued low price, coupled with reduced takings, combined to make drilling unattractive. The principal oil wells completed, by counties are: Boone, 6; Calhoun, 10; Clay, 7; Gilmer, 5; Kanawha, 5; Lincoln, 7; Pleasants, 13; Ritchie, 32; Roane, 6; Tyler, 7; and Wirt, 14. Production for the year, according to the Oil and Gas Journal, was 3,724,750 barrels. The leading counties in gas, with the number of successful wells in each, are: Boone, 16; Braxton, 13; Cabell, 47; Calhoun, 29; Doddridge, 10; Gilmer, 55; Kanawha, 127; Lincoln, 18; Ritchie, 29; Wayne, 19; and Wetzel, 26. Production for the year is estimated as 150,000,000,000 cubic feet. Pipe-line construction, which was extensive in 1937, was insignificant in 1938. Exploration was not as active as in 1937. Field prices of both oil and gas have severely declined.

Jan 1, 1939

By David B. Reger

Exploration for new pools of gas in the Oriskany sand and continued exploitation of areas already known to be productive in that sand were the main features of petroleum activity in West Virginia during 1938. To a considerable extent the exploration program resulted in failure, but the extension of former areas was eminently successful. Throughout the state, in general, less drilling was done than in 1937. According to the West Virginia Department of Mines, only 631 permits to drill were issued, as compared to 1034 in 1937. The account of operations, as reported by trade journals and other sources, shows that 766 wells were drilled, resulting in 131 oil wells with 1609 bbl. of daily production; 484 gas wells with 1,232,216,000 cu. ft. of daily open flow; and 151 dry holes. Several discoveries indicate new pools of oil and gas; and several extensions of old gas pools have been made. In spite of a decreased number of total wells, the figures for new gas and oil are both larger than in 1937. The new oil average is 12.3 bbl. per well per day; the gas average is 2,545,900 cu. ft. per well per day, the ratio of dry holes to completions is 19.71 per cent. No general attempt was made to discover new pools of oil. A continued low price, coupled with reduced takings, combined to make drilling unattractive. The principal oil wells completed, by counties are: Boone, 6; Calhoun, 10; Clay, 7; Gilmer, 5; Kanawha, 5; Lincoln, 7; Pleasants, 13; Ritchie, 32; Roane, 6; Tyler, 7; and Wirt, 14. Production for the year, according to the Oil and Gas Journal, was 3,724,750 barrels. The leading counties in gas, with the number of successful wells in each, are: Boone, 16; Braxton, 13; Cabell, 47; Calhoun, 29; Doddridge, 10; Gilmer, 55; Kanawha, 127; Lincoln, 18; Ritchie, 29; Wayne, 19; and Wetzel, 26. Production for the year is estimated as 150,000,000,000 cubic feet. Pipe-line construction, which was extensive in 1937, was insignificant in 1938. Exploration was not as active as in 1937. Field prices of both oil and gas have severely declined.

Jan 1, 1939

By A. Josefsson

The transition temperatures of 0.01 to 0.02 pct carbon steels are shown to be strongly influenced by cooling rate in the a range, quenching from A, causing a very low transition temperature even after strain aging. In a titanium-stabilized steel and in a steel with 0.05 pct C this effect is absent. NORMAL mild structural steels usually show a structure of more or less pure ferrite, as a matrix, in which cementite grains or pearlite are embedded. Of these components, ferrite is by far the most interesting one as far as ductility and brittle (cleavage) fracture are concerned. Obviously, pear-lite and carbide are by no means necessary for a cleavage crack to nucleate and grow in the ferrite, as steels with a very low carbon content (Armco iron with 0.02 pct C) have an impact transition temperature just as high as semikilled steels with 0.26 pct C.1 Although it has been argued that a very embrittling effect is to be expected from cementite, precipitated as continuous films along the ferrite grain boundaries,'. " the micrographic evidence for a direct causal connection between the brittleness and these films does not seem to be very convincing. On the other hand, it has been stated that cementite particles in ferrite are able to stop ferrite cracks.4,5 In any case, the properties of the ferrite itself seem to be of overwhelming importance to the ductility of steels, justifying a thorough study of steels consisting of ferrite of different compositions, but principally free from pearlite, which means a carbon content below 0.02 pct. Such investigations have been carried out using the impact transition temperature as a criterion of the tendency to brittle fracture and have given some rather unexpected results. One result is the profound influence of carbon on the transition temperature of the steel in normalized condition. If the carbon content is reduced from 0.02 to 0.015 pct and below, a nearly discontinuous decrease in transition temperature appears even with high percentages of such elements as phosphorus and nitrogen present. This will be reported elsewhere." The present paper deals with another effect of carbon upon transition

Jan 1, 1955

By E. H. Wells, A. Andreas

New Mexico retained its position as the sixth largest oil-producing state for the year 1937 with a total production of 38,484,630 bbl. This was an increase of 11,680,184 bbl. over the 1936 production of 26,804,446 bbl., or a gain of 43 per cent. The production for Lea County during 1937 was 35,961,056 bbl.; for Eddy County, 2,136,251 bbl.; and for northwestern New Mexico (San Juan and McKinley Counties), 387,323 bbl. The average daily non-marginal well allowable for Lea County on Jan. 1, 1937, was 92 bbl.; at the close of the year it was 67 bbl. The average daily pipe-line runs were less than the allocations of the New Mexico Oil Conservation Commission, but slightly in excess of the state allowables recommended by the United States Bureau of Mines. The average daily production for the year was 105,437 barrels. The total number of completions in the state was 742, of which 638 were oil wells; 19 hydrocarbon gas wells; 5 carbon dioxide gas wells and 80 dry holes. Of the dry holes, 46 were in proven fields. Of these 46 dry holes, 13 were in the Artesia-Grayburg-Jackson-Maljamar area, Eddy County, two in the Getty Extension field, Eddy County, 11 in the Red Mountain field, McKinley County, three in the Rattlesnake field, San Juan County, and nine in the Aztec-Bloomfield area, San Juan County. There were only eight dry holes in the proven fields in Lea County. Southeastern New Mexico Lea County.—The Monument field was the largest producing field in Lea County, with 10,945,788 bbl., closely followed by the Eunice field with 10,927,929 bbl. The Hobbs field, formerly the largest producing field in Lea County, was relegated to third .place, with 7,292,522 barrels. Drjlling during the year closed the gap between the northern part of the Eunice field and the southern part of the Monument field. The wells in this area were relatively small, because of decreased porosity in the lime. The greatest activity in Lea County was in the Monument pool, with 199 completions, 197 being oil wells, one a gas well and one a dry hole.

Jan 1, 1938

By R. W. Gurry, L. S. Darken

The solubility of cementite in austenite is computed by thermodynamic methods from the observed solubility of graphite. It is found that the solubility of cementite is greater than that of graphite in the entire austenite temperature range. Thus the prior discrepancy between this portion of the phase diagram and the observed metastability of cementite is partially resolved. FOR several years it has been apparent that a serious discrepancy exists in certain observations pertaining to the Fe-C system. Direct experimental data indicate: 1-That the curve representing the solubility of graphite in austenite'" crosses that for cementite4 at about 945°C as shown in Fig. 1. 2— That graphite and austenite saturated therewith are stable1 relative to cementite at all temperatures between the eutectoid, about 723°C, and the eutectic, about 1153°C. These observations are mutually incompatible in view of a well-known consequence of the second law of thermodynamics, namely, that the stable phase (presumably graphite at all temperatures) has a lower solubility than the metastable phase (presumably cementite). Hence either 1 or 2 above must be in error; either the measured solubility of graphite or of cementite, or the observation as to the stability of graphite, is in error. Our present purposes are: 1—To collate the available data on cementite and prepare a table of HO — HO° and of (Fa— HO°)/T. This tabular method seems the best and most convenient way to represent the heat and free energy of formation. 2—To determine whether the measured solubilities of cementite and graphite in austenite are in accord with the above table and the measured thermodynamic properties of austenite, in order to resolve, if possible, the existing paradox of these two solubilities. Enthalpy of Cementite The enthalpy of cementite at 273 °K, H279 — HOcem, was computed by integration of the low temperature heat capacity as measured by Seltz, McDonald, and Wells" 68" to 298 °K) and as given by the Debye functions recommended by them (0" to 68°K); the result is included in Table I. At higher temperature HCem — H,,"" is given by Kelley who used the data of Naeser7 (298" to 1037°K) and of Umino8,9 (273° to 1923°K). We have recalculated Hcem — H273 cem from the data of UminoO in the following way. In the equilibrated alloy at temperature the weight fraction of cementite Pct c -Pct cr is PctC -PctCr designated f(C), and the

Jan 1, 1952

By Cuppam Dasarathy

The incidence of liquid inzmiscibility in binar)) indium alloys has been theoretically analyzed on the basis of the Hildebrand-Alott equation. Bedictions of miscibility or otherwise Imve in general been found to agree with those phase diagrams that are already publislzed in the literature. Out of a total of 27 systems, where either the complete phase diagrams are published or liquid immiscible behavior is reported, the Predictions agree with the experimental data in 25 systems, the exceptions being the Te-In and Ni-In systems. According to the equation, liquid immiscibility is also indicated in the binary alloys of indium with K, Rb, Cs, Na, Sr, Ba, Ti, Zr, V. Nb(Cb), Ta, W, U, Re, Ru, Rh, Os, and Ir. RECENT investigations by the author have shown that indium when alloyed with iron, chromium, and cobalt shows liquid immiscible behavior.1"3 The Fe-In phase diagram shows a wide range of compositions where the liquids are immiscible.4,5 No intermediate phases are present in this system. No precise information is available about the extent of liquid immiscibility in the Co-In system. However, it is certain that there is a range of compositions where the liquids are immiscible and that there are two or three intermediate phases,376 in the system. Liquid immiscibility is also strongly indicated in the Cr-In system and no evidence was obtained in the brief investigation to indicate the presence of intermediate Cr-In phases.2 The present paper deals with a theoretical analysis of binary alloys of indium with certain elements of the periodic table and indicates the systems where liquid immiscibility may be expected. The incidence of liquid immiscibility in binary systems has been theoretically examined by many workers and many excellent papers are available on the subject. In this paper, the alloy systems are examined on the basis of the more recent ideas proposed by Mott.7,8 It has been claimed8 that the Mott parameter predicts the incidence of miscibility or otherwise with reasonable accuracy and consistency. BACKGROUND TO MOTT&apos;S APPROACH Hildebrand applied his immiscibility rule for non-polar liquids to various alloy systems.9 The basis of this rule is that the equation for the excess free energy of formation of a liquid solution is rather similar to the theoretical expression for the energy of mixing of a regular solution. He postulated that when the heat of mixing is sufficiently high, separation into liquid phases will occur and the condition for complete CUPPAM DASARATHY is at the Research Centre, British Steel Corporation, (South Wales Group), Port Talbot, Glamorgan, Great Britain. Manuscript submitted March 12, 1969. IMD miscibility was shown as where VA and VB were the atomic volumes of the components A and B, and ?EV the energy of vaporization of the component. The term (?EVA/VA)1/2 was regarded as a measure of the binding energy of the component A and was called the L&apos;solubility parameter" 8A. On this basis immiscibility occurs when 1/2(VA+VB)(bA-bBf > 2RT [2] Apparently, however, there were several inconsistencies in that according to Eq. [2] several systems known to be miscible in the liquid state were predicted as immiscible. MOTT&apos;S ANALYSIS ~ott&apos;" regards that the reason for the inconsistencies arising out of Hildebrand&apos;s equation was largely due to the electrochemical attraction between the two elements, not being considered. Hence, Eqs. [I] and [2] were modified by taking into account the electro-negativities of the two elements XA and XB, and Mott arrived at an equation for immiscibility, i(VA + VB)(6A - aB)2 - 23,Q60n(XA - XBf > 2RT [3j which can be written as i **&£*&* >&apos;*°™- &apos;• HI T being the melting point of the more refractory component of the system. In Eq. [4], the numerator was called the Hildebrand term, the denominator, the electronegativity term, and their ratio, the Mott number. Mott observed that if the Mott number of a given binary system was greater than the maximum number of Pauling bonds which the two metals could form, then liquid immiscibility could be expected. The maximum number of bonds formed by a given metal was considered to be directly related to the number of bonding electrons available, i.e., to its maximum valency. Since the valencies of the elements considered vary from 1 to 6, Mott assumed that if the ratio of the Hildebrand term to the electronegativity term was >6, then immiscibility could be expected. On the contrary, if the ratio is <1, the metals should be miscible. Further, the alloying behavior is not only influenced by the valencies of the two elements but also by the relative atomic sizes that influence the types of packing and hence the coordination number. Mott considers that on average the maximum number of near neighbors of unlike atoms is 6. Thus, on both valency and size factor considerations, Mott concludes that the maximum number of bonds&apos; possible in any system was 6, this being the upper limit of the Mott number for miscibility. In considering the alloying behavior of systems with Mott numbers between 1 and 6, Mott plotted the num-

Jan 1, 1970

By E. R. Helderman, C. Y. Ang, C. C. Nealey

Beryllium-base alloys have been successfully p7.-epared by the liquid-phase sintering technique. Depending orz the composition and amount of the intended liquid please, microstructures either single -phase or duplex in feature with randomly oriented grains have been obtained. Qualitative and semi-qualitative determination of distribution of alloying elements md microsegregations in some experi)uzental alloys haue been made by electron-micro-probe analysis in conjunction with microliardness testing and standard metallography. Tensile tests reoealed that some conzpositions possess attractive elastic properties with Young&apos;s mot1uli greater than 40 X 10&apos; psi. In powder metallurgy, liquid-phase sintering is a process or phenomenon that has proven to be of practical value. For example, the heavy metals such as tungsten-copper-nickel, high-strength heavy gyro alloys,&apos; heavy-duty electrical contacts,&apos; and tungsten carbide tool materials are all products of liquid-phase sintering. Mechanisms involved in liquid-phase sintering, however, are not completely understood. Questions regarding the exact roles played by rearrangement of particles, liquid/vapor surface energy, solution and precipitation, and so forth, have not been completely answered. Evidence has been cited3 that at least volume shrinkage in the densification process is diffusion-controlled. It is possible that the predominant mechanisms for the complete densification and grain growth in a liquid-phase sintered system depend primarily on the alloy systems involved, in addition to processing conditions. Despite the lack of sound understanding of the mechanisms of the process, liquid-phase sintering has been and is being used to advantage either to synthesize microstructures for their special properties or to prepare alloys which are difficult to form by fusion process. Liquid-phase sintering of beryllium alloys was first attempted by Jones and Williams.4 They first tried infiltrating beryllium with magnesium, and then succeeded in preparing the alloy by sintering Be-Mg powder compact in molten magnesium bath. This investigation resulted in the identification of some Mg-Be intermediate phases. Crossley et a1.5 also used liquid-phase sintering technique in an attempt to produce ductile beryllium alloys for structural applications. The major liquid-phase components investigated by Crossley et al. were aluminum and silver with minor additives of germanium, calcium, lanthanum, cerium, and yttrium. The lack of wetting and the bleeding out of liquid phase were the difficulties encountered during experimentation. According to Hodge,6 the two compositions investigated by Crossley, which showed some promise based on compression tests, involved large amounts (over 35 wt pct) of silver, thus making them too heavy to be of practical interest to the aerospace industry and military users. The present investigation was prompted by the search for light-weight (density less than aluminum) beryllium alloys exhibiting small anisotropy in physical properties for precision inertial navigation instrument applications. In addition to isotropy, good structural properties such as high elastic modulus or desirable combination of mechanical and physical properties are also objectives of this investigation. The technique of liquid-phase sintering was chosen for its versatility in producing either duplex or homogeneous microstructures. This report is concerned with the use of copper and aluminum, with or without silicon addition, as the intended liquid phase, and the resultant micro-structures and some physical properties of the beryllium alloys. Qualitative and semiquantitative electron-microprobe analyses of some of the alloys are presented to illustrate the usefulness of this microanalytical technique for the identification of microconstituents and their distribution. EXPERIMENTAL PROCEDURES The beryllium powder used was -200 mesh Brush Beryllium Co. QMV NP-50 grade. Typical chemical analysis of the powder is shown in Table I. Commercial high-purity copper, aluminum, and silicon powders all screened to —100 mesh were used as additions. Mixed powder compositions were ball-milled in ceramic jars for 1/2 hr to ensure thorough blending. Milled powder was loaded either in 3/4-in.-diam button die or in Metal Powder Association flat tensile specimen die and compacted under top and bottom pressure. No lubricant or organic binder was used. Sintering was carried out in a quartz tube under a vacuum of 50 to 100 µ pressure. Surface hardness and some microhardness readings were taken on sintered specimens. Sintered density was

Jan 1, 1965

but, returning to South Africa, for the next two years he was assistant general manager of the Simmer Deep Gold Mining Co., at Johannesburg. In June, 1911, he returned to New Zealand as general manager and consulting engineer for the Consolidated Goldfields of New Zealand, at Reefton, which position he held at the time of his admission to the 1nstitute in 1914. Early in September, 1915, he left New Zealand for active service in France. Corporal Sheppard B. Gordy Sheppard B. Gordy, born in Ansonia, Conn., in 1889, graduated from the Sheffield Scientific School in 1910 and with the degree of E. M. in 1912. He entered the employ of the Braden Copper Co. immediately on his graduation and remained with this company four years, working up through the various grades to assistant foreman and foreman to one of the individual mines. The last year he was in its employ, he acted as general mine foreman. He was for a short time with the Chile Exploration Co. and then went with the Andes Exploration Co. (Anaconda) and remained with the latter, doing mine exploration and development work, until he sailed for home in June, 1918, to give a more personal and active service to his country in her need. He declined a tender of induction into an officers&apos; training camp, at the urgent request of Professor McClelland supplemented by Mr. Potter, because they demonstrated to his satisfaction that he could give more valuable service to his country in helping out with the aircraft production. Being within the draft age, in order to carry out this plan, it was necessary for him to be called by his Local Board and sent to camp. This call came Aug. 26. Two weeks before that time he had gone to Dayton, Ohio, to begin the study of aircraft production, and was sent by the Dayton Board to Camp Sherman, Chillicothe, Ohio, where he died of pneumonia on Oct. 9. Lieutenant Thomas Clarence Gorman Thomas C. Gorman, a lieutenant in the Second Tunnelling Company of the Canadian Engineers, was killed in France on Mar. 18, 1918. He was resting in his sleeping hut and was in the act of writing a letter when a bursting shell killed him.

Jan 1, 1920

By H.E. Brauer

Among the zinc base alloys used for casting in metal moulds, pnrticularly die casting, those alloys containing aluminum usually together with copper, are probably the most widely used. The reason lies in their desirable mechanical properties and the fluidity and absence of hot shortncss which facilitate ca,sting. Objection to the use of these alloys may be raised on account of the rather frequent instances of failure of a type variously described as disintegration, exfoliation and intererystalline corrosion. In all cases which have come to our kno~vlcdge where the conditionsof service were known, failure has occurred upon cxposurc to moisture and heat varying from a hot moist atmosphere to lligh pressure steam. RIoreover, the alloys described in all such roses contain impurities or alloying metals which the present authors have found to have enormous accelerating effects on intererystalline oxid:~t&apos;ion in zinc-aluminurn alloys. Thus Williams1 experimented with an alloy containing a large percentage of tin exposed in Cuba. Baucr2 reports failure of a boiler plug containing over 1 per cent. of impurities, doubtless lead for the must part, and Rawdon&apos;s3 examinations were madc on an alloy containing 0.1 per cent. lead also exyosctl to thc Tropics. No thorough investigation of the nature and cause of this type of failure has been made heretofore, so far as the authors are aware, although Rawdon correctly classified it as internal oxidation. We have, therefore, carried out this investigation in order to det&apos;ermine the exact nature of this phenonienon and the effect of other metals present as impurities or intentional additions in accelerating or retarding it. In the appendix we include a considerable amount of data which may be valuable in selecting an alloy combining good physical properties with high resistance to oxidation. At the time this work was undertaken the best available equilibrium *Investigator, Metal Section, Research Division, The New Jersey Zinc Company. &apos;H. W. Williams—Jour. Am. Inst. of AIet,als, Vol. 11, p. 221 (1917). 2o. Bauer—ZeiL, fiir i&apos;vletall Kunde, Vol. 12, .No. 7, pp. 129-31 (1920). 3H. S. Rawdon—Trans. Am. Elcctrochcmic.al Society (1921).

Jan 1, 1923

By H. E. Brauer

Among the zinc base alloys used for casting in metal moulds, pnrticularly die casting, those alloys containing aluminum usually together with copper, are probably the most widely used. The reason lies in their desirable mechanical properties and the fluidity and absence of hot shortncss which facilitate ca,sting. Objection to the use of these alloys may be raised on account of the rather frequent instances of failure of a type variously described as disintegration, exfoliation and intererystalline corrosion. In all cases which have come to our kno~vlcdge where the conditionsof service were known, failure has occurred upon cxposurc to moisture and heat varying from a hot moist atmosphere to lligh pressure steam. RIoreover, the alloys described in all such roses contain impurities or alloying metals which the present authors have found to have enormous accelerating effects on intererystalline oxid:~t&apos;ion in zinc-aluminurn alloys. Thus Williams1 experimented with an alloy containing a large percentage of tin exposed in Cuba. Baucr2 reports failure of a boiler plug containing over 1 per cent. of impurities, doubtless lead for the must part, and Rawdon&apos;s3 examinations were madc on an alloy containing 0.1 per cent. lead also exyosctl to thc Tropics. No thorough investigation of the nature and cause of this type of failure has been made heretofore, so far as the authors are aware, although Rawdon correctly classified it as internal oxidation. We have, therefore, carried out this investigation in order to det&apos;ermine the exact nature of this phenonienon and the effect of other metals present as impurities or intentional additions in accelerating or retarding it. In the appendix we include a considerable amount of data which may be valuable in selecting an alloy combining good physical properties with high resistance to oxidation. At the time this work was undertaken the best available equilibrium *Investigator, Metal Section, Research Division, The New Jersey Zinc Company. &apos;H. W. Williams—Jour. Am. Inst. of AIet,als, Vol. 11, p. 221 (1917). 2o. Bauer—ZeiL, fiir i&apos;vletall Kunde, Vol. 12, .No. 7, pp. 129-31 (1920). 3H. S. Rawdon—Trans. Am. Elcctrochcmic.al Society (1921).

Jan 1, 1923

By R. C. de Lange

An improved replica technique is developed for a nondestructive study of the nucleation and growth of fatigue cracks. Three different growth stages of a fatigue crack were observed. An initial stage of high growth rate is followed by a long period of very slow growth, until finally a third period of high growth rate leads to fracture. THE metal-fatigue process is of a very complex nature. The experimental approach towards fatigue is susceptible to many minor influences which, together with the unavoidable scatter in testing results, makes the interpretation a matter of extreme care. The generally accepted fact that, in a homogeneous material, the fatigue cracks start at a free surface indicates that surface studies may contri-but in an essential way to a better understanding of the fatigue mechanisms. Indeed metallographic observations of the fatigue phenomena have been very fruitful in the last decade. The study of extrusions, intrusions, and persistent slip bands has contributed much to the present knowledge of the early processes in fatigue.&apos; The drawback of the current metallographic techniques lies in the fact, however, that either observations of fatigue phenomena had to be made in a destructive way after an only partly executed test or a sequence of observations on the same test bar was only possible on notched specimens.2 4 In both cases an uncertainty exists as to the nucleation and growth of the fatigue crack in an unnotched test bar, where the crack can start at any place of a large area and develops in a test bar, which is macroscopically

Jan 1, 1964

By J. A. SINGMASTERN

THE New Jersey Zinc Co.&apos;s vertical retort plants are believed to have been in continuous operation through the whole year. At Palmerton metal purer than that made from the same ore in the old plant has been produced and has been able to compete successfully with very pure electrolytic metal in die castings and other special uses where extreme purity is worth money. A new plant using this process was put in production by the Grasselli Chemical Co. at Meadowbrook, W. Va., early in the summer. It is said to be working very satisfactorily. It is understood that this plant will not produce high-grade metal. Two patents issued to Bunce and Mahler (Nos. 1,749,126 and 1,749,127) describe a method of operating the vertical retort so that practically lead-free metal can be obtained from ores containing consider- able lead. The zinc vapors and other gases leaving the reaction zone are filtered through a column of material maintained at a temperature high enough to prevent much zinc from condensing. The filtering medium is either periodically or continuously changed.

Jan 1, 1931