Search Documents

By H. S. Rathor

NTPC (National Thermal Power Corporation), a multi-unit organization, is generating 26% of India’s total power. This power is produced from its 14 coal based stations and 7 gas based stations. NTPC is entering into the business of power-distribution, power-trading, setting up of coal mines and diversification in non-conventional energy sector as well. For achieving the goal of the country “Power for All” NTPC has taken a giant stride by entering into Hydro Power generation which is also the cheapest and the cleanest renewable source of energy. In its pursuit for excellence, 800 MW Koldam Hydro Power Project is NTPC’s first venture in hydro sector. In Koldam, hydropower potential will be harnessed by constructing a 163m high earth and rock fill dam in a narrow gorge at upstream end of Bhakra reservoir. The river diversion is envisaged through two parallel, 14m finished diameter ‘horseshoe’ tunnels of length 901m and 934m at village Kian on the right bank, where the river forms a 180° loop. The diversion tunnels are designed to accommodate a flood of 6500m3/sec, taking into account the maximum probable discharge of 200 years return period. The tunnels pass through dolomite and limestone rock formations. The excavation of tunnels was done with drill and blast method. The excavation was attempted from both inlet and outlet faces. During geological investigation a rock fault was located at the outlet area. The location of the fault was such that it was passing through the edge of the Tunnel-1portal and around 30m away from the face of the Tunnel-2 portal. The quality of the rock at Inlet was also poor. To save the portals from slips, excavation of the tunnels was planned to start after the completion of the open excavation and its support system both at inlet and outlet. The tunnel excavation at inlet was envisaged by approaching the tunnels’ portal by constructing a road through 540EL bench and meeting the inlet portals on the upstream end, which would have been ready by mid2003, only after completion of the open excavation and its support system. To save time and cost, it was felt necessary to modify the planning by starting the tunnel excavation simultaneously along with open works both at inlet and outlet. The excavation at the inlet face of the tunnels started in December 2002 after rerouting the approach road to inlet portals through haulage road on the downstream and similarly Tunnel-1 at the outlet was started in the low cover area before completion of open area works. Thus the tunnel—heading excavation was started nearly 06 months early with the change of methodology.

Jan 1, 2005

By David Estrella, Hector M. Lizama, Jhonny Carrión

"Microcel™ sparging systems were installed on one column of the molybdenum cleaner circuit and one column of the copper first cleaner circuit at Antamina. The Microcel™ system is known to generate finer bubbles than jetting-type spargers, and smaller bubbles have been associated with higher recoveries in flotation. Alternating tests were carried out on the molybdenum column, using either jetting-type spargers or the Microcel™ system. Experimental conditions of gas flow rate, wash water rate, and froth depth were tested. Use of Microcel™ decreased the bubble sizes from 2.6-2.9 mm to 1.5-2.0 mm. In addition, Microcel™ improved both unit molybdenum recovery and unit molybdenum concentrate grade. In the copper first cleaner circuit, side by side tests were carried out that compared the Microcel™ column with a parallel columns fitted with jetting-type spargers. Best results were obtained at manifold pressures of 260-290 kPa, where bubble sizes of 1.6-2.6 mm were observed. In either copper or molybdenum flotation, the Microcel™ system required only 50-60% of the gas flow used by jetting-type spargers.INTRODUCTIONAntamina is a copper-zinc mine located in the Peruvian Andes. Compañía Minera Antamina is owned by BHP Billiton (33.75%), Xstrata (33.75%), Teck Cominco (22.5%), and Mitsubishi (10%). The mine was commissioned in 2001 with a capital investment of US$2.3 billion, and has a nominal 100,000 t/d mill capacity. Mining, milling, flotation, and tailings impoundment take place at the mine site, which sits at an altitude of 4,300 m above sea level. The deposit is a polymetallic skarn ore body with intrusive phases of quartz-monzonite porphyry into Cretaceous aged limestone [Evans et al, 2005]. Ore body thickness is 100 to 150 m and has the shape of a flat-lying crescent. Copper is present mainly as chalcopyrite with a minor bornite component. Zinc is present as sphalerite. Molybdenum is present as molybdenite. Some lead, bismuth, and silver are associated with the sulphides. The deposit is currently classified into six main ore types [Dechert, 2006], grouped into two categories: copper and copper-zinc. The mill produces four concentrate types: copper, molybdenum, zinc, and lead-bismuth. Copper, zinc, and lead-bismuth concentrates are transported by pipeline down to the port of Huarmey. Molybdenum concentrates are bagged and trucked to port."

Jan 1, 2008

By Dave Bulled, Khiratt Husain

"The use of High Pressure Grinding Rolls is gaining significant interest as a replacement for SAG milling in the comminution of hard rock ores because of the potential for reduced costs in terms of energy and grinding ball consumption. Estimation of expected energy consumption for fullscale operations has conventionally involved the testing of a few fairly large samples in pilot scale HPGRs. This paper describes the development of a small-scale batch test method for determining a work index for HPGR of a large number of samples that can be used to show the variability of the ore as an integral part of a geometallurgical approach to circuit design and production forecasting.The test equipment that was developed comprises a hydraulic press with adjustable pressure operating on small batches of ore in a locked cycle test procedure. A work index measurement was determined that links the specific energy consumed in the test to the breakage achieved such that the index can be used to predict comminution energy requirements.The measurements were calibrated against laboratory scale HPGR equipment to develop a model for design and forecasting that includes crushers, HPGRs and ball mills in a complete comminution circuit.INTRODUCTIONEstimation of the expected energy consumption for full-scale HPGR operations has conventionally involved the testing of a few fairly large samples in laboratory and pilot scale machines (Danilkewich, 2006). With the financial input of five mining corporations, SGS Lakefield Research has developed a small scale test capable of providing relevant information on the variability of energy consumption and size reduction from drill core samples. It is our intention that the values measured in the test will be scaled up, through benchmark comparison with pilot sized and full sized HPGR units, to allow plant design and throughput forecast on a block by block basis of the mine plan using a new CEET program. CEET® (an acronym for Comminution Economic Evaluation Tool) is an advanced grinding design and performance predicting tool that uses energy relationships to model the performance of SAG / Ball mill circuits."

Jan 1, 2008

By Tuncel M. Yegulalp, Anuta Belova

This paper expands on the ZECA (Zero Emission Coal Alliance) technology, which is aimed at making coal a sustainable source of clean energy in the near future. The technology proposed immediate capture of carbon dioxide and other pollutants upon generation, thus alleviating their negative effects in the Earth’s atmosphere. ZECA proposes using chemical energy of coal to produce hydrogen; the latter is then used to produce electricity via fuel cells or Hyrogen-Oxygen turbines. In this study, a chemical engineering package, AspenPlus 12.1, is used to simulate the reactor (reformer) in which hydrogen is produced from methane water and lime as part of the zero emission power plant. Thermodynamic conditions, pressure and temperature, are optimized with respect to molar hydrogen production. Under the proposed conditions, molar conversion efficiency, carbon to hydrogen, of 95% is achieved. Further studies are required to model the complete power plant and to optimize it for efficiency.

Jan 1, 2005

By E. Douglas, D. N. Collins, J. R. Stevens

E. Douglas (Dept. of Scientific and lndustrial Re-search, Warren Spring Laboratory, Hertfordshire, England) — The authors are to be congratulated on the considerable improvements they have made in tailoring efficiency and selectivity terms which are generally superior to the alternative forms in current use. However, I feel that their efficiency expression is limited to lower-grade feeds; its accuracy reduces as the feed grade increases. For example, its application to such processes as the beneficiation of glass sands, refractories and clays will invoIve considerable inaccuracies. The reason for this lies in the direct use of recovery, which, with high-grade feeds, biases their empirical expression, R(1 - c/h). With a 90% grade feed, the recovery weighting for the slightest degree of beneficiation, over a zero efficiency sampling operation, will be 90+%+ I disagree with their second basic requirement which states that there can be no fundamental basis for any single quantifying expression. A formula giving a comprehensive representation of concentra- tion efficiency can be derived fundamentally accord-to the procedure outlined in the literature. '' This formula, called the Basic Efficiency formula, is

Jan 1, 1963

By Hua-Zhong Yu

Gold is one of the most widely used substrate materials for self-assembly. Self-assembled monolayers (SAMs) prepared from alkanethiols and their derivatives on gold are the most reliable and well-studied systems to date, which have attracted much attention because of interest in two-dimensional molecular assemblies, and of their potential applications in molecular devices, sensors, and functionalized interfaces. Gold electrodes are also very important in microelectronics and electroanalytical chemistry. This work reports the characterization of a new type of gold substrates for self-assembly. The gold substrates are constructed from recordable compact disks (R-CDs) with simple and straightforward wet-chemical treatment, and can be made at desired sizes and shapes that satisfy different experimental needs. In particular, an easy, inexpensive, and reproducible method to prepare self-assembled monolayers (SAMs) on CD-R gold substrates after removing the protective polymer films with concentrated nitric acid was described.

Oct 1, 2003

By Paul M. Tyler

Magnesite is of importance primarily as a refractory material for lining steel furnaces , although substantial amounts are used in the production of flooring compositions and other building materials and for certain chemicals , notably epsom salts . Since consumption for all of these purposes is largely in the eastern United States and domestic deposits are situated in California and Washington , this country's magnesite mining industry , which was created largely by war- time conditions , has subsequently been sustained by tariff protection .

May 1, 1931

By Bill Kyslinger

In underground mining, machine design is predominantly dictated by mine conditions and individual customer desires. In partnership with Boart Longyear Poland and KGHM, J. H. Fletcher & Company was tasked to design and manufacture a single-boom, single operator drill module for installation of 1.2 meter expansion bolt in a 1.6 meter height mine. The objective was to produce a machine to provide ergonomic improvements for the operator while working in the mine environment. This dictated the requirement for a small easily controlled, maintenance friendly design with a remote operator?s control station. The selected design method was to use starter and finisher drill steels. This combination, requiring a number of mechanized machine motions, provides the ability to drill the required depth in the specified mine height. To accomplish the task from a remote location, a conscious decision was made to employ current technology in the form of small pressure compensated hydraulics and electronic controls. The result of the design method is a modular assembly with each sub-component designed to be replaceable and adjustable independently from other machine components. The low profile remote roof bolting module is made up of six major sub-components. Each major component is painted a different color to help the operator make the visual connection from the drill module to the operator?s control/display monitor. The Stabilizer (White) secures the module between the mine top and floor. The Drillhead (Orange) produces the drilling rotation and torque but also must slide out of position to allow the machine to manipulate the drill consumables. The Drill Steel Carousel (Blue) holds and indexes the starter and finisher steel from position to position. The Manipulator Arm (Green) moves and guides the drill steels and drill consumables from position to position during installation. The Roof Reference Guide (Yellow) locates the mine roof and guides the drill steels and drill consumables into position. The Linear Bolt Carousel (Purple) holds the drill consumables. The low profile remote roof bolting module allows the operator to drill and install a roof bolt manually or automatically with the push of a button. This design substantially reduces the operator?s exposure in the mine environment, as well as inherent pinch points and rotary hazards. Positioning the operator safely in the confines of the air conditioned cab.

Jan 1, 2006

By Manuel Arnáiz, Pedro R. Sola, Rogelio Baudot, Manuel Herrera, Carlos S. Oteo

The aim of this paper is to describe and analyze the ground treatment performed between January and May 2002 in order to increase safety during excavation and reduce instability problems along 180 m of tunnel, during the construction works associated with line 10 extension to the Madrid Metro. The tunnel was excavated using the traditional Madrid Method and in the section considered in this paper layers of sand were detected around the tunnel crown area with a significant presence of water, the in?ow of which needed to be controlled with a minimum impact on the surrounding environment.

Jan 1, 2003

By R. Karl Zipf, Francois E. Heuze

Stress analysis programs such as MULSIM/NL, LAMODEL, MinSim 2000, and EXAMINETAB are used in the mining industry to analyze stresses and displacements in coal mines, platinum mines, gold reefs, and tabular-type deposits. These relatively simple numerical models can efficiently simulate yielding and failure of a rock mass near a mine opening and subsequent stress transfer. The main input parameters for these models are a family of nonlinear stress-strain curves for the in-seam material. For many applications of these models, such as in coal mining, extensive field measurements and observations exist from which to estimate these stress-strain curves and calibrate the numerical models; however, such measurements are lacking for other types of mines. A three-step method is presented to determine nonlinear stress-strain curves for boundary-element (BE) programs used in many mining applications. The method requires a suite of laboratory-scale strength tests at various confining pressures. Note that this analysis uses laboratory-measured strength and modulus properties of alluvium. The dependency of the mechanical properties of alluvium on scale has not been established, although more tests are being planned. However, it is believed that the relative comparisons performed are valuable regardless of scale effects. First, the FLAC2D computer program is used to model the laboratory tests and determine cohesion (c) and friction angle () for a Mohr-Coulomb material model. Second, another FLAC2D model uses the c and values to calculate vertical stress and strain around a single opening in the rock mass. This model calculates the stress-strain path of points at various distances from the opening boundary. Finally, based on these stress-strain paths, the stress-strain curves needed for a BE analysis are derived. This three-step method was demonstrated in a large, flat-lying underground test facility in very weak rock. The BE analyses agreed well with observations of failure at the test facility and provided a basis for evaluating the behavior of alternative layouts.

To provide cooler air to miners working in hot areas of mines, particularly new deep hardrock mines. Approach Air supplied to hot working areas of mines is cooled by passing it through a series of water sprays. How It Works Water nozzles mounted inside a section of ventilation tubing release cooling sprays of water into the air being blown through the tube. The prototype of the water spray cooler consists of six evenly spaced water sprays located inside a 10-ft. long section of 16-inch-diameter fiberglass ventilation tubing. See diagram. This section of rigid tubing is installed into one of the positive pressure ventilation tubing lines that conduct fresh air into working stopes. The intake manifold to the six water sprays is connected to the mine?s cool water line, and the water valve on the manifold is opened. Warm ventilation air being supplied to the stope passes through the water sprays, and is cooled by the lower temperature water.

Jan 1, 1979

A fundamental component of grade control at Tarmoola Mine has been the monitoring of assaying through quality assurance programs. The programs have concentrated on issues related to accuracy and precision of leachwell and fire assay techniques, sample preparation and grade variability within a sample. An outcome of monitoring has been identification of shortcomings in the application of assaying techniques to Tarmoola ore types that contain coarse particulate gold. Leachwell has shown satisfactory precision since introduction as the primary assay technique in October 1998 but leachwell accuracy and recovery through comparison with fire assay techniques has identified bias. A bias toward higher fire assays in grades above 2 g/t invoked an investigation into the cause of the discrepancy between leachwell and fire assay. Testwork evaluated Leachwell assay recovery by varying leach time duration, which showed that by increasing the leach time improved recovery significantly. Monitoring of leachwell against fire assay had shown that a leachwell (200 g) with a one hour leach has under-called grade when compared with fire assay by up to 18 per cent, on average, for Tarmoola ore types. Alternatively, optimisation of the leachwell assaying technique using a 200 g pulp and a two hour leach has returned, on average, higher assays than fire assay by up to eight per cent. Testwork on screen fire assays, duplicate assays and fire assay to extinction has demonstrated assay variability associated with coarse, particulate gold. The variability and distribution of gold in Tarmoola ore types has emphasised the importance of high quality sample preparation for leachwell assaying to ensure liberation of gold to leaching solutions. Assay quality assurance protocols are vital to assay data integrity and enable confidence in delineation of ore-waste boundaries and provide early recognition of problematic assaying periods and isolation of grade control practices, which depart from performance standards critical to the operation.

Jan 1, 2000

By Manqiu Xu

"Ore grades are decreasing and ore deposits are becoming more complex. In order to make a sound economical decision about a mining project, metallurgical testwork must be carried out. A few large “representative” samples cannot represent the metallurgy of a large ore body and a large number of samples reflecting variation in ore head grades and in mineralization types must be obtained for proper metallurgical studies, including flowsheet development for a greenfield project. A relationship can be established between the recovery of valuable minerals and ore grade for each mineralization type. This relationship can be used to establish a correlation between values recoverable and values contained in the ore body that can include multiple pay metals. With this information, a sound economical decision can be made about the viability of a large mining development project.INTRODUCTIONThe demand for minerals today is historically high as many countries are being rapidly industrialized. The supply for these minerals is not necessarily running short. However, it is widely accepted that the world today is running short of the easy to mine and easy to process ore deposits. As ore grade is decreasing and ore mineralogy is becoming more complex, metallurgical testing must be fully conducted in order to make a sound economical decision about a mining project. For a high-grade and high-quality deposit, it is hard not to make a good profit even with low metal prices. For a low-grade and hard to process deposit, the profit margin is much lower and is dependent on the throughput and the recovery of valuable minerals. The recovery of valuable minerals is a function of ore grade and mineralogy and it must be experimentally determined for a given processing option.At Vale Base Metals Technology Development, metallurgical testing for an existing operation or brownfield project is termed as Ore Evaluation, while metallurgical testing for a greenfield project is termed as Flowsheet Development (Xu, 2011). In the past, metallurgical testing involved a few large composite samples for lab and pilot plant testwork. As ore deposit becomes less homogeneous and more variable, a few large composite samples cannot represent the metallurgy of a large ore body. In addition, useful information about the deposit such as zones of “impurities” or floatable rock minerals would not be obtained. Different processing strategies could have been developed if the locations and sizes of these zones were known in advance. For proper metallurgical studies, a large number of samples reflecting variation in ore head grades and in ore mineralization types must be used. A relationship can be established between the recovery of valuable minerals and ore grade for each mineralization type. This relationship can be used to estimate values recoverable in the ore body that can include multiple pay metals. Ultimately, the recovery verses ore grade relationship will be used in business decision-making."

Jan 1, 2013

By R. B. Crookston

This paper presents the status and mining method chosen by each of the active underground oil shale projects in the united States today. Potential improvements in equipment and methods on the near-term horizon are discussed. The problems and potentials that lie in the long-term future of oil shale mining are examined in light of the demands which must be met by this developing technology.

Jan 1, 1981

By Samantha Beeson, Collin Poole

"This paper examines the development of two new selective flocculation techniques for recovering KCI values from low grade carnallite potash ore.Direct recovery of KCI was achieved using one of two mid-range molecular weight polymers, one non-ionic and the other strongly cationic, in conjunction with the same selective anionic dispersant. From initial response studies on pure minerals and selective flocculation tests on synthetic mixtures, investigations were extended to recover KCI values from a natural carnallite potash ore. A single-stage process achieved products grading up to 61.3% KCI at recoveries up to 85.4% for the cationic flocculant suite and up to 64.8% KCI with recoveries as high as 90.3% for the non-ionic flocculant suite, with dispersant and flocculant dosages of 150-250gr1 and 10-75gr1, respectively. These results clearly demonstrate not only the feasibility of treating such problematic ores at low reagent dosages, but also the potential elimination of desliming prior to froth flotation.The experimental results presented are considered in terms of the reagent adsorption phenomena present in the system and various aspects of floe formation and cleaning.IntroductionAs high-grade sylvinite potash ores become scarce, lower grade sylvinite and carnallite potash ores are becoming more attractive. However, these ores often contain large amounts (up to 15% by weight) of water-insoluble slimes which must be removed prior to KC! flotation, owing to their high adsorptive capacity for the amine collectors used. The slimes are generally removed by scrubbing followed by hydroclassification and any residual material not eliminated is blinded with reagents such as guar gum or starch to inhibit interference in subsequent KC1 flotation.An alternative approach used commercially in Canada by Agrium Inc. involves water-insoluble slimes flotation prior to KC! flotation. In this process, the slimes are selectively flocculated and then separated by froth flotation. Losses of KC! to the slimes product and associated brine requirements are both reported to be less than those encountered in conventional desliming, but the technique is somewhat limited in its application at present."

Jan 1, 1997

By L. Alan Weakly

Global warming is a political reality in the United States today. The actual impact of the continued utilization of fossil fuels is not known and is open to debate. However, the growing concern about the continued use of these fuels is problematic. There are technologies available to us today that would permit America to meet its future energy demand and not contribute to global warming. The inconvenient reality is that fossil fuels cannot completely be replaced with energy conservation and the use of wind, solar, hydroelectric, geothermal and nuclear energy. The connection between the greenhouse effect and global climate change was first identified by physicist John Tyndall in the 1860s. To prove the greenhouse hypothesis, Roger Revelle and his research team started measuring carbon dioxide concentrations in the earth?s atmosphere in the early 1960s (Becker, 2007). With the rising concern about global warming, scientists throughout the world have been obtaining surface and air temperature data. Scientists have also been comparing CO2 concentrations found in glaciers throughout the world with theorized annual temperatures. Data for both dates back 1,000 years. Armed with this data, many nations of the world and the United Nations Intergovernmental Panel on Climate Change (IPCC) have concluded that climate change is a reality. The IPCC also concluded that this climate change is the result of mankind?s consumption of fossil fuels and that catastrophic consequences will occur on a

Jan 1, 2008

By G. Danko

MULTIFLUX, a new thermal, hydrologic, and airflow model and software is being developed to solve the flow of heat, moisture, and air in and around an underground opening. MULTIFLUX couples two distinct domains that are solved separately first and re-coupled as an iterative task: (1) the rockmass, and (2) the airway. The airway is solved with a lumped-parameter Computational Fluid Dynamic (CFD) module which is an embedded part of the MULTIFLUX code. The CFD model includes convection, conduction, and radiation for heat, as well as convection and diffusion for moisture transport in an air-filled opening. The CFD model also solves for the airflow field. The surrounding rockmass model may be from any analytical solution, or from a complex thermal-hydrologic numerical model such as NUFT or TOUGH2. The rockmass model is interfaced to MULTIFLUX using a novel technique called Numerical Transport Code Functionalization (NTCF). The method provides fast convergence on a personal computer platform. The paper reports the results of MULTIFLUX simulations for a mine drift, comparing calculations with a known mine climate software, CLIMSIM, and with measured data. Through this validation example, the performance of MULTIFLUX is demonstrated. The results show excellent agreement due to the use of realistic modeling assumptions and boundary conditions.

Jan 1, 2009

By Balu E. George, Subhadeep Banerjee, Shailesh R. Gandhi

"A three-dimensional analysis of laterally loaded helical piles installed in cohesionless soil is presented. Finite Element Analysis was conducted using commercially available Plaxis 3D AE version, assuming Mohr-Coulomb failure for soil. Pile is modelled as plate elements with a single helical blade attached to a hollow shaft. The ultimate load for various configurations is examined considering deformation criteria. The Bending Moment distribution and maximum lateral deflection are also discussed. It was observed that the ultimate lateral load carrying capacity increased by presence of helical blade and the maximum deflection also got reduced. The diameter of the helical blade was found to have significant effect on the lateral deflection, maximum bending moment and the ultimate load. However, the observations from the study suggest that the presence of helical blade seizes to produce considerable effect after a certain depth. Difference in failure pattern with regard to the distribution of soil resistance observed for different geometries considered for numerical analysis are also touched upon.INTRODUCTIONHelical piles or screw anchor piles have gained popularity due to fast installation, instant use, and other advantages over the traditional piles. They are usually used to support structures like solar panels, light houses, and other light structures which are subjected to uplift loads. However, such structures are often subjected to significant lateral loads as well. Under lateral loads, the response of helical piles can be different from that of a conventional pile due to the presence of the bearing provided by the helical blade. However, the proper design remains a concern due to lack of work carried out on the lateral capacity of helical piles.The lateral performance of helical piles is significant because they can act as efficient alternative to conventional piling systems in many applications.The lateral load capacity of screw anchor piles with different number of helices were examined by Mittal et al. (2010) by experiments in sand. They found that the lateral load capacity of piles increases with addition of helical blades. Prasad and Rao (1996) examined the lateral capacity of helical piles in clay by experiments on model piles and found that the lateral capacity of helical piles were more than that of the straight shaft piles. It was observed that the lateral capacity increase with embedment depth and shear strength of soil. Sakr (2009) studied lateral performance of two section helical piles in soft soil. The investigation by Prasad and Chari (1999) reported that the pressure distribution across the diameter is not uniform for circular piles, but it is maximum at the centre and almost zero at the two edges.Puri et al. (1984) after conducting model tests on single-helix, two-helix, and three-helix anchors installed in sand, proposed a mathematical model that was fashioned after Matlock and Reese’s elastic theory model. Elkasabgy and Naggar (2015) investigated he lateral performance of full scale large capacity helical piles in structured cohesive soils and reported the modulus of sub-grade reaction to be non linear."

Jan 1, 2017

On April 1, 1982, the Bureau of Mines and the Department of Energy entered into an Interagency Agreement to develop an enhanced computer cost model for uranium in situ leach mining. The original computer cost model contained data base information related to two regions; the Wyoming basin region and the South Texas trend area. The enhanced cost model contains additional information on San Juan Basin type deposits. This addition is significant because it expands the model's capabilites to include one of the largest uranium producing areas in the United States and developes costs related to uranium production from in situ leach mining. The data base was expanded and modified to include changes necessary for San Juan basin type deposits. These changes included, but were not limited to, state and local taxes, royalty payments, depth of deposits, drilling costs, and electrical costs. Also site visits were taken to verify many of the base case parameters. Consequently, the data base has been incorporated into the computer program and existing software was modified to provide for the additional data. Information was obtained on drilling coats and therefore the current program more accurately reflects these costs to depths of 2500 feet. This depth parameter has been expanded to include Wyoming Basin and South Texas scenarios also. Verbal communications were held with one operator in the Crownpoint, New Mexico area as well as the state regulatory agencies to help validate the expanded model. As a result of these changes, several tables have been included, summarizing changes in the new default parameters and the overall range of input parameters.

Jan 1, 1982

By Morgan L. Race, Matthew R. Glisson

"Most driven pile projects have plumbness limits from 0.25 in/ft (21 mm/m) to 0.5 in/ft (42 mm/m) to control bending stresses. For two projects, the project teams performed static load testing to evaluate performance of piles with sweep. One project, located in Grand Forks, North Dakota, used 9.625-inch (244-mm) diameter piles with a wall thickness of 0.395 inch (10 mm) and lengths ranging from about 130 to 160 feet (40 to 49 m). Measured pile sweep (lateral offset distance of the pile toe from the pile top) was between 12 and 17 inches (305 to 432 mm). Static load testing indicated that the piles could support the design load with axial deflection of less than 1 inch (25 mm) but only provided about 80 to 90 percent of the ultimate resistance at axial deflections of about 1.9 to 1.7 inches (49 to 43 mm), respectively. The other project, located in Shakopee, Minnesota, used 9.625-inch (244-mm) diameter pile but with a wall thickness of 0.352 inch (9 mm) and lengths around 50 to 90 feet (15 to 27 m). The measured sweep varied between about 20 and 63 inches (508 and 1,600 mm) for 9 of 214 piles driven at the site. Load testing indicated that these piles could provide the required design resistance with less than 0.3 inch (8 mm) of axial deflection and support the required ultimate resistance with about 0.5 to 0.6 inch (13 to 15 mm) to of axial deflection.INTRODUCTIONAnyone who has observed a significant number of piles has seen that, inevitably, the pile is not perfectly straight after driving. In spite of the best efforts of contractors, there are a whole host of reasons for piles to end up out-of-plumb or to have a curve, sometimes referred to as pile sweep. Most project specifications set limits for plumbness typically between 0.25 in/ft (21mm/m) and 0.5 in/ft (42mm/m) (USACE, 1991; PDCA, 2007; MnDOT, 2016; MoDOT, 2016). Closed-end pipe piles, including monotube or tapertube, are the only pile type that allow actual measurement of the final alignment of the pile.As Nadeem, et al. (2015) note, buckling failure of long, slender piles is the predominant mode of pile failure in soft soils. Pile sweep is just one source of buckling failure in long, slender piles. The nonlinear buckling analysis showed that increasing slenderness ratio and/or increasing degree of curvature decreases the loadcarrying capacity of a driven pile. Nadeem, et al. (2015) considered solid, steel pile with lengths from 24 to 66 feet (7.5 to 20 m), diameters from 9.75 to 26 inches (244 to 660 mm), initial bends from 2 to 6 inches (50 to 150 mm), and half- and quarter-sine shapes."

Jan 1, 2017