Search Documents

By Pierre Roy, Claude Gosselin, Maryam Sadeghi, Michel Bourassa, Christian Rochefort, Claude Bazin, Gautier Mahieu, François Lavoie, Marilène Renaud, David Cataford

"Spirals are gravity concentrators used for the concentration of iron oxide minerals from ores. This paper presents the mineral size recovery curves observed for spirals operating in two Canadian iron ore processing plants. The size recovery curves are presented for rougher, cleaner and re-cleaner spirals. The partition curves observed for the spirals are significantly different than those observed for typical gravity concentration devices such as hydrocyclones or hydraulic classifiers. The size recovery curves show the complex behaviour of the minerals as they flow down a spiral and are analysed with a view toward process modelling and simulation. Initial simulation results show that gains in the iron recovery can be achieved by increasing the recovery of coarse iron oxide particles in the rougher spirals.INTRODUCTION Spiral concentrators are gravity based separation devices used for the preparation of coal, iron and different heavy minerals ores (Wills, 1992). The classification of the particles in spirals is based on the combination of gravity, centrifuge, drag, lift and Bagnold forces (Atasoy and Spottiswood, 1995; Burt, 1984; Bouchard, 2001). Several papers are dedicated to the analysis of the forces acting on the particles flowing down a spiral (Das and al., 2007; Sivamohan and Forssberg, 1985; Holland-Batt and Holtham, 1991; Holtham , 1992). Most of these papers aim at the development of a general model for the simulation of the classification of the particles for coal ore processing. Few papers deal with the operation of spirals for processing iron ores (Hyma and Meech, 1989; Srivastava, 2001; Dallaire et al., 1978) and fewer papers present results for spirals used as cleaners following a rougher stage. Since the classification in spiral classifiers is dependent on the particle size and specific gravity a partition or performance curve commonly applied to classifiers (Mai Manga et al., 2012) is used here to analyse spiral operation. Few papers were found to describe the operation of spirals in terms of partition curves (Atasoy and Spottiswood, 1995; Holland-Batt and Holtham, 1991; Richards et al., 2000). Most of the investigations presented the application of a model to simulate the position of coal particles of various sizes and specific gravities along the trough of a spiral (Kapur et al., 1996; Holland-Batt and Holtham, 1991). In addition most of the available literature on spirals deals with one stage of concentration by spirals (Dallaire et al., 1978; Das and al., 2007; Sivamohan and Forssberg, 1985) while industrial circuits usually consist of rougher and cleaner spirals."

Jan 1, 2014

By N September, R Abate

Bateman Modular (previously Van Eck and Lurie) has been building and supplying the mining industry with modular DMS plants for the last 30 years. These DMS modules range in capacity from 1 tph to 200 tph. The most popular unit produced by Bateman Modular over the years has been the 50 tph module. Development In the last 7 years a need has arisen from the industry to provide Modular DMS plants that can treat higher tonnages (150 to 200 tph). The first DMS provided to the mining industry based on the modular concept was a 150 tph DMS Module to MIBA in the DRC. Since then Bateman Modular has provided some 14 Mega DMS modules over the last 7 years with the latest two orders from Debswana (Damtshaa double up project) and Namdeb. Ever since the first Mega Module was supplied Bateman Modular has been improving the Modules. Implementation The modules can be supplied in different configurations so as to improve the overall availability of the plant. Two off 150 tph DMS modules were supplied for a Transhex operation. This allowed the client to still operate one DMS module while maintenance is being performed on the other DMS module. The client also has the option of choosing a single module. Successes The following list of projects provides the base for the success of the Mega Modules.

Jan 1, 2006

By John W. Cole

The Bureau of Mines conducted a trenching and sampling project during 1947 on the tungsten-rich granodiorite that outcrops in Henderson Gulch, Montana. During the course of this investigation, interest was attracted to the Sunrise copper-gold mine in metamorphosed limestone in the north slope of the gulch. The mine was examined by S. H. Lorain, Chief, Mining Division, Albany Branch, in May 1948. A trenching and drilling program was recommended to develop a parallel vein indicated by outcrops to lie below the principal productive Queen vein. In the meantime, the Queen Mining Syndicate initiated a trenching program that exposed high-grade lead-copper-silver-gold ore in a nearly vertical vein that strikes N. 600 E. to east. A core-drilling program to develop this vein was initiated in September 1948. This report presents the factual data obtained from the trenching and drilling operations. The Sunrise mine was discovered about 1890. Production has been estimated to be $120,000 in gold from 40,000 tons of ore mined during the period 1892-1903. The tailing from this operation was treated by cyanidation in 1912, with a reported recovery of $3.50 to $4.00 a ton from 15,000 tons of material. Subsequent production of sulfide ore was 7,396 tons treated by smelting, with recovery of 1,569.42 ounces of gold, 10,003 ounces of silver, 352,899 pounds of copper, and 354 pounds of lead.

Jan 1, 1950

By Jan E. Nesset, Phillip J. Mackey

"Studies have shown that there is a correlation between commissioning and start-up time, i.e. time to reach full plant design capacity, and the degree of innovation and technical/engineering uncertainty in the project design. The paper describes the types of start-up curves for plants according to the level of technology or uncertainty in the process design. The need to properly describe and understand the commissioning and start-up time is examined using these curves and the importance on project success is highlighted. A number of case histories of recent mining and metallurgical projects are also reviewed. Finally, the paper reviews how to better assess the level of start-up uncertainty associated with a project and makes suggestions for decreasing the commissioning time due to technological risk.INTRODUCTIOThe start-up of a new mining and metallurgical facility, a much anticipated event, is a critical step in the life of such a project. Achieving a successful start-up and reaching the design capacity on-time requires careful planning, a thorough understanding of the key technological and engineering components involved and a well-trained and adequatelystaffed start-up crew. In this paper, some of the aspects related to start-up of a mining/metallurgical project will be explored, and in particular, the impact of the technology component will be examined. In order to illustrate this, a number of case histories based on recent mining and metallurgical projects will be discussed. Ways of assessing and understanding the uncertainty associated with technological issues related to start-up of a mining and metallurgical plant will also be examined.The history on mining and metallurgy is full of success stories of great mines and mills that are now considered “company makers” (well known examples of such successes include the Horne mine for Noranda which had a 1 year start-up in 1926-27, the Dome mine for Placer Dome, the Grasberg deposit for FMI in Indonesia). Less well documented are specific studies relating to plant start-ups and what constitutes a success or a failure, however there are a few notable references in the literature and these will be reviewed."

Jan 1, 2003

Two new inorganic-organic hybrid polymers, Al(OH)3-polyacrylamide (Al(OH)3-PAM) and Mg(OH)2-polyacrylamide (Mg(OH)2-PAM) were synthesized and successfully applied for the treatment of oil sand tailings. The results indicate that both Mg(OH)2-PAM and Al(OH)3-PAM were unaffected by the change in pH, and could be applied to oil sand tailings with varying sand-to-fine ratio (SFR). The optimum dosages for the Mg(OH)2-PAM and Al(OH)3-PAM were about 330 g/ton and 650 g/ton, respectively for SFR 3.75. The flocculated oil sand tailings dewater quickly producing 66-68% solids. The flocculated tailings produced similar filtration rate before and after shear. Mg(OH)2-PAM treated oil sand tailings produced twice the filtration rates (220 ml/min) compared with Al(OH)3-PAM. This study clearly indicates that Mg(OH)2-PAM and Al(OH)3-PAM is a viable solution while decreasing the mass-production of tailings and increasing the rate of water-recycle.

Jan 1, 2012

By K. A. Lewandowski

Leach heaps are plagued with problems due to fine material migrating downwards, clogging the spaces between the coarser ore particles, resulting in decreased metal recovery rates. The use of a binder in agglomeration would allow the fine material to be immobilized, increasing the availability for the solution to come in contact with all the ore. As much as 1.64*1012 BTU per year would be able to be saved if a 25% increase in copper recovery was experienced, assuming that 70% of heap leaching units converted to using agglomeration technology. This is equivalent to approximately 18% of the energy currently being used in leaching heaps.

Jan 1, 2008

Introduction Research has shown that when an emergency occurs, work-ers often do not get the information they need to take appropriate action. Important information about incidents is either not com-municated effectively or not at all to those affected by the event. The "Emergency Communication Triangle" safety talk focuses on the content of emergency warning messages. It presents a procedure using mental cues that can be used by senders and receivers of emergency warnings. The talk includes graphics for use during the presentation, as well as references for more information. Background Interviews with 48 miners who had escaped one of three different underground mine fires revealed that warning information provided to them was inadequate. Either insufficient information was provided to miners inby the fire areas or they failed to ask the questions needed to let them plan and execute an effective escape. Most of the miners who evacuated from these three mines did not have information that would allow them to make decisions about efficient escapes. The communication breakdown came from two directions: (1) the individuals providing the warning did not offer details about the situations even though some were known and (2) the individuals who received the warnings did not ask for clarification of the situation. The lack of information allowed miners to continue attempting to place cues into normal frameworks after they should have evaluated the situation as abnormal and threatening. The uncertainty created by the lack of information influenced their decision-making and therefore their actions. Approach Researchers at the NIOSH Pittsburgh Research Laboratory have developed a training intervention that can be used by senders and receivers of warnings during a mine emergency. This material was developed for use in short safety training sessions such as start-of-shift safety talks. The information can be presented in about 15 minutes. Although the illustrations were taken from the underground coal mining industry, the training can be tailored to any work setting by substituting appropriate examples. How It Works During the safety talk, miners learn about the six categories of critical information that should be provided during emergency communications: Who, Where, What, Miners, Event, and Response. • Who: When reporting an emergency or receiving a warning, the first thing a miner must do is identify himself or herself. This is important because people react differently based on who gives them information. • Where: Giving or finding out the location of the problem is important. Of the 48 miners interviewed about their escape, only 2 knew where the fire was located. However, this information was known by either the dispatcher or the person who discovered the fire. • What: Miners must tell or ask exactly what is happening. At one mine fire, miners near the phone heard the message to evacuate and went to gather the others on their crew. One worker shouted to a machine operator: "Come on down to the mantrip. We're going out." Because it was close to quitting time, the machine operator thought they were just leaving the section a little early and went through his normal end-of-shift routine, wasting valuable time. After giving or obtaining the three initial pieces of critical information, miners can then give or obtain details about the response in progress. • Miners: Is anyone hurt? Has everyone been accounted for? When and where was a missing person last seen?

Sep 1, 2004

A computer program for the static load analysis of linear elastic structures is presented. It is the product of a two-year project for the development of a efficient program for the analysis of mine-type structures. The report is divided into two parts. The first part explains the general method of analysis, the computer program organization and the most significant numerical techniques used. The second part is a user manual for the computer program. The FORTRAN IV computer program deck and example problems were transmitted separately to the sponsor. Request for a copy of the program should be directed to the Bureau of Mines, Denver Mining Research Center.

Jan 1, 1972

By R. Bergstrom

The implementation of a Quality Management System (QMS) or an Environmental Management System (EMS) that conforms to the standards issued by the International Organisation for Standardisation (ISO) no longer needs to result in a bureaucratic nightmare supported by mounds of paperwork. In this sense, this paper describes the Quality Management System that was implemented and demonstrates how the technologies that were developed can be used to satisfy other similar requirements.

Aug 25, 2002

Henry Walker Eltin (HWE) are the mining contractors for Gloucester Coal at Stratford mine, which is in an environmentally sensitive area in the Avon Valley, NSW, Australia. Normal blasting at Stratford is done in a “stand up” or “box cut” mode to suit the truck and shovel operations. Recently an opportunity of doing a throw blast became available when part of a ramp had to be blasted to accommodate changes to the pit design while not damaging the remainder of the ramp. The objective was to maximise throw into the void in order to minimise excavation costs by reducing the amount of overburden to be moved by the excavation fleet. It was necessary that the best result be achieved while staying within the vibration and airblast limits at a neighbouring property and nearby township. Both objectives were achieved through the application of Orica’s knowledge of blast design, modelling and i-konTM electronic detonators.

Jan 1, 2003

By Hendrick A. D. Kirsten, A. Clayr Alexander

Stillwater Mining Company is currently developing a second underground palladium and platinum mine approximately 21 km (13 miles) west of their existing Nye operation in the Bear tooth Mountains of southern Montana. Portals for the two access tunnels required at the new site were excavated in limestone talus to accommodate4.6 m (15 feet) diameter tunnel boring machines. A review of the technical design, field conditions and construction of the portals is presented.

Jan 1, 2001

By S. P. Godby, S. P. Sharples

Wind-tunnel tests were carried out of the conditions under which nuisance dust particles (100-1 000 micrometres) become entrained by wind. A laser entrainment monitoring system (LEMS) was used, and was found to provide an accurate means of assessing nuisance dust emissions from a surface. Accurate determination of the threshold entrainment velocity of dusts using the LEMS gives a baseline against which the performance of dust control techniques can be evaluated. Minerals tested included coal, petroleum coke, limestone, sand and pulverised fuel ash. Pilot field trials of a portable wind tunnel equipped with the LEMS have been successfully completed, providing a means of validating laboratory results in the field

Jun 19, 1905

By Josef K. Alter

Crosshole Sonic Logging (CSL) of drilled shafts requires 1.5-in (38-mm) or 2-in (51-mm) I.D. sonic access tubes to be installed inside the steel reinforcement cage. The sonic access tubes do not contribute to the structural capacity of the drilled shaft. The proposed use of Ischebeck TITAN T73/56 CSL/Hollow Threaded Rebar for Cross Hole Sonic Logging Access Tubes Combined with Longitudinal Concrete Reinforcing in Drilled Shafts (patent pending) is discussed as an alternative method of construction and CSL probe access. The T73/56 hollow threaded rebar/sonic access tube performs as a high strength rebar while at the same time creating a 2.2-in (56-mm) I.D. sonic access tube. The deformed high strength hollow bar provides better adhesion to concrete thus reducing the problem of debonding associated with smooth PVC and steel pipe. A cost comparison using conventional rebar with added sonic access tubes is discussed. The use of T73/56 CSL/Hollow Threaded Rebar as a value engineering alternative can reduce both material and labor costs for drilled shaft construction and can provide an advantage where anchor bolt cages and longitudinal reinforcing create congestion.

Jan 1, 2011

By Micheal Mitariten

The recovery of natural gas (primarily methane) from coalbed deposits is an established and growing source for the U.S and accounts for over 7% of its total production. The gas from on-purpose degassing is often pipeline quality and requires only compression and dehydration before being admitted to the pipeline grid. However, the raw gas is sometimes contaminated with nitrogen (N2) and/or carbon dioxide (CO2) that can make the gas inadmissible to the transportation pipeline. In general, the N2 must be 4% or less and the CO2 should be 2% or less. In treating gas produced from virgin coal bed or from degassing operations where CO2 is present, amine systems are traditionally used for its removal. Engelhard’s Molecular Gate® adsorption system offers an attractive alternative due to its skid-mounted equipment, low pressure and unattended operation, cost and high on-stream reliability. Natural gas can also be sourced from the residual coal, after the coal has been mined. This source can be the GOB or gas remaining in abandoned coal mines. This source is almost universally contaminated, often with a combination of CO2 and N2. If the source is from air intrusion, the source can also be contaminated with O2. In treating CO2 / N2 contaminated feeds, the Molecular Gate adsorption system removes both of the impurities along with a level of O2 within a single processing step. To date, ten Molecular Gate units are underway with three systems having been installed for upgrading gas from abandoned coal mines. The technology consists of specialty adsorbents and advanced PSA processes that are jointly offered as fabricated packaged equipment by Engelhard Corporation and Guild Associates, Inc. Upgrading requirements, project challenges and project arrangements are discussed in this paper.

Jan 1, 2005

By K. G. Kebkal, R. Bannasch

"Because the operation of tethered underwater vehicles in the deep ocean or under drifting ice areas is very complicated or impossible, the application of autonomous underwater vehicles (AUV) is preferred or even the only possible solution. However, this implies the possibility of a direct and real-time control over all AUV functions, which is only achievable with the availability of accurate positioning/navigation and a high-speed communication link. This paper presents a flexible bottom- or surface-based solution enabling high positioning accuracy of underwater objects (harvester, AUVs, bottom nodes); specifically, a multifunctional system that combines Ultra Short Baseline (USBL) transceivers and Long BaseLine (LBL) stations deployed at a large depth. Moreover, each baseline transponder is equipped with a high-speed communication device to provide the means for real-time AUV control based on the information about its current position, e.g. navigate it with direct commands and operating its actuators and other mechanisms. Moreover a communication link with a high data rate can provide valuable visual information from the operation area.Depending on how many nodes the LBL grid comprise has, target transponder positions can be estimated with an accuracy of several to tens of centimetres. The purpose of the paper is to present the experiments with all key elements of the multifunctional Hydro-Acoustic USBL-aided LBL Positioning and Communication System."

Sep 1, 2014

By Joseph T. Coe, Siavash Mahvelati, Alireza Kordjazi

This paper introduces recent advances in stress-wave NDT systems for use in assessments of in-service foundation integrity and drilled shaft construction. The primary results of the laboratory experiments are very promising, as the acquired image was capable of differentiating changes in pile cross section as low as 0.3 cm. The preliminary results with the same hardware components on a relatively large scale cemented sand model were also promising. A brief overview is provided of both systems including hardware, survey methods, and data processing techniques, followed by a discussion on application of the results to QA/QC of deep foundations. INTRODUCTION There are two main applications in which current QA/QC NDT technology fails to provide sufficient information regarding deep foundation conditions: (1) detection of flaws in outside cover concrete of drilled shafts and corrosion in steel piling; and (2) evaluation of anomalies beneath the bottom of drilled shaft excavations. Previous studies have demonstrated the capabilities of high frequency stress waves for geotechnical and foundation evaluation purposes (Lee and Santamarina 2005; Coe and Brandenberg 2010; Coe and Brandenberg 2012; Coe and Kermani 2016). Higher frequency waves can visualize smaller anomalous features at the expense of higher attenuation and smaller propagation distance. Therefore, the goal of this study was to advance the state of NDT practice by development of a prototype high resolution stress-wave imaging system as proof-of-concept. The equipment and hardware were modular, which allowed simultaneous development of two system configurations for application to in- service foundations as well as drilled shaft excavations during construction. Results are presented based on two large scale soil models. The first laboratory model simulated section loss in an in-service steel pipe pile and drilled shaft foundation (Fig. 1a). The second model simulated anomalous conditions beneath drilled shafts excavations as might be encountered in areas with significant karst (Fig. 1b). For both models, evaluation of foundation conditions relied on the propagation of small amplitude seismic stress waves using hardware similar to those described in Coe and Brandenberg (2010) and Coe and Brandenberg (2012).

Jan 1, 2018

By Leslie F. Sawatsky

Failure of drainage works is one of the principal threats to the sustainability of mine closure facilities but the risk can largely be remedied by appropriate design of mine closure drainage facilities. The feasibility of sustainable mine closure facilities that avoid failure of drainage systems needs to be established during the early stages of mine planning, before mine disturbances make sustainable closure uneconomical. Experience in mine development shows there is often enough latitude in mine plan development to incorporate measures with neutral economic consequence and positive environmental benefit. Project managers need to resist the temptation to develop mine plans and closure drainage plans independently. Integrated mine planning with effective inputs by environmental specialists and drainage designers may affect the overall mine configuration, footprint and schedule. Key issues pertain to the end pit location, waste dump configurations, pit infill elevations, fluid impoundments, diversion channel routing and preservation of flows to receiving waters. Guidelines with illustrations of suitable practices are presented to assist mine planners.

May 1, 2004

By B. Papillon

There has been a veritable increase in the adoption of electronic detonators in the last few years. Electronic detonators offer several distinctive features over electric and non-el (shock tube) detonators including better timing accuracy resulting in excellent fragmentation and vibration control, certainly key mining parameters. The field programmability also helps in reducing the on-site magazine storage of detonators with diverse fixed delays. A typical electronic detonator may consist of a logic core, a communication interface, storage capacitor(s) and the ignition element. Being electronic components, the electronic detonators may be susceptible to RF or electromagnetic interference (EMI). RF sources are virtually everywhere: cellular phones/towers, radio transmission, microwaves, walkie-talkies, high voltage (HV) transmission cables and wireless networks with their characteristic frequency emissions. Safety issues prevail; e.g., whether the RF interference can cause premature or inadvertent firing whether directly or indirectly. From a reliability perspective, the RF interference may also impact on bus communications, e.g., during the logging, verifying, charging and firing phases. The deleterious communications disturbance may result in a misfire (non-firing of one or more of the detonators) which is terribly inconvenient for the mine operators and even pose a safety hazard.

Jan 1, 2009

By Gabrielle Gaustad

For aluminum, substitution of primary with secondary resources decreases energy consumption; this energy advantage creates a strong economic incentive to recycle. Several authors have raised concerns that the current sinks for secondary materials may soon be saturated, impeding subsequent expansion of recycling. This work combines dynamic material flow analysis with optimal batch planning models to quantify the significance and drivers of these pending limits under several scenarios, and thereby explore potential opportunities to increase recycling. An aluminum recycling system case was developed that includes containers and packaging, automotive, and construction products and scraps. The impacts on aggregate scrap utilization and materials cost are explored in the context of changing alloy demand and lifetime. Insights drawn from this specific case study could be applied to multi-stakeholder, systemic models.

Jan 1, 2010

By J. Sliwinski, J. Oliveira

"The application of geometallurgy and corresponding sample selection can take on several formats within industry. Current practice can range from a strictly geostatistical approach to one in which geological and metallurgical parameters are used in combination to create a representative sample selection strategy. The stage of a project and the level of information available at the time of sampling influences the methodology used to create a representative sample.A geometallurgical study of Carpathian Gold’s Rovina Valley Project in Romania is used to demonstrate a sample selection strategy that integrates geological, mineralogical and metallurgical data to maximize the relevance of the geometallurgical unit definitions. This approach, practiced by Xstrata Process Support for its’ clients, ensures that the results of the metallurgical program can be interpreted in the context of these units.INTRODUCTIONGeometallurgy is a cross disciplinary approach in which metallurgical performance of an ore is linked to intrinsic geological and mineralogical characteristics. The objective of a geometallurgical study is to characterize the range of metallurgical performance of an orebody. This allows the geoscientist or metallurgist to create a robust flowsheet able to treat the full range in variability and to develop production strategies to maximize financial performance. The standard approach is to individually sample and test a series of ore types or geometallurgical units. Several different approaches are used in industry to define what constitutes geometallurgical units and how to sample them.One current methodology is the use of multivariate statistics. Geochemical data along with available geological data are used to define multiple variability domains (Williams, 2004; Walters, 2009). There are risks associated with this methodology since the extent of the data set itself may not support a purely statistical approach at the time that metallurgical units need to be defined. The assay suite collected by exploration programs is often limited to pay metals while metallurgical performance is often affected by ore gangue components. Furthermore, in many cases metallurgical scoping and pre-feasibility studies take place prior to the availability of extensive geochemical data sets. Purely statistical methods can produce multiple populations which require extensive sampling, testing and validation prior to consolidation into a reasonable number of composites for metallurgical testing. Methodologies are therefore required that allow representative sampling and testing of consolidated geometallurgical composites to occur at various phases throughout the development of a mining project."

Jan 1, 2013