Search Documents

By C. Meyer, J. J. Eidel

C. W. Hunt I wish to register strong disagreement with the choices of drilling sites chosen by the Continental Scientific Drilling Committee, while endorsing the stated objectives. Of special significance is the lack of any site involving the metals most needed today in the US, while 9 to 13 km of drilling are allocated to gold and silver districts and 11 to 17 km to base metal (mainly copper) districts. Why is nothing proposed for platinum group or chromite? Is this because the committee did not know of such a site? If so, I offer such a site in California (see Fig. 1). The mineralization shown in Table 1 occurs in a large peridotite body in western Tehama County, CA. Petrography has demonstrated unequivocal evidence of migrated PGE deposited in peridotite and chromite of hypabyssal nature. Active diapirism (due probably to serpentine buoyancy) above a reactivated mantle to surface conduit marks the position of the conduit. Young explosion breccia cemented loosely by volcanic glass and tuff demonstrates the significance of the conduit as the prime source of the various emissions. Deep drilling could result in major metals discoveries as well as shedding light on the grand questions of platinum group mineralization. What role water has played in this occurrence is not yet certain; but chlorine and asphaltite have been detected in and adjacent to native PGM, suggesting a major role for water. The explosion breccia suggests that this excellent site could overlie entrapped geothermal steam.

Jan 6, 1987

By Jean M. Richardson, Steven R. Williams

"Geometallurgical mapping is a new team-based approach that documents variability within an orebody and quantifies the impact of geology (host rocks, alteration and structure) and mineralogy on grinding, metallurgical response and metal recovery processes. The quantitative, spatially constrained database that results can be readily integrated into 3-D block models and mine planning activities. Thus it is an important tool to reduce the technical risk associated with new mine developments or expansions.Normally undertaken during pre-feasibility or feasibility planning stages, the first step of geometallurgical mapping is to review the geology, mineralogy and other critical parameters and construct a geometallurgical matrix. This matrix provides an objective base to then guide sampling and/or compositing activity for physical property and metallurgical testing. Depending on the project, an array of testing techniques can be used to characterize the ore and feed data into the geometallurgical model.While the range and number of tests needed is project-dependant, the geometallurgical mapping approach allows the development of empirical models or interdependent relationships, grounded by spatially-constrained real data. Extensive data sets collected using less expensive testing methods can be meaningfully correlated with results from complex specialty tests to yield realistic metallurgical recovery data.With geometallurgical mapping completed, the resulting database can be integrated into an overall 3-D block mine model. This means that metallurgical response can be used to realistically forecast the recoveries of specific blocks, perhaps sampled only by drilling. Mine planning can then incorporate the forecasted metallurgical response and generate future project cash-flows; opening the door to economic optimization of the mine exploitation."

Jan 1, 2004

By Felipe Perissé Duarte Lopes

The tensile properties of DGEBA/TETA epoxy matrix composites reinforced with different amounts of curaua fibers were evaluated. Tensile specimens with up to 35% in volume of long, continuous and aligned curaua fibers were room temperature tested in an Instron machine. The fracture was analyzed by SEM. The results showed significant changes in the mechanical properties with the amount of curaua fibers. This was compared to other bend-tested composites with distinct matrices. The fracture analysis revealed a weak fiber/matrix interface, which could be responsible for the comparatively low performance of some properties.

Jan 1, 2010

By Wils L. Cooley

Several aspects of coal mine safety-ground system operation are studied. Evaluations of two sophisticated ground-wire monitors are presented, along with a detailed report of development work on a modular ground-wire monitor. A portion of the report covers stray current flow in the safety-ground system, analyzing in detail conditions surrounding the generation of both dc and ac ground wire current. Considerable detail is provided concerning studies of mine ground beds. Additional progress is reported in the development of a. continuous ground-bed monitor, and new techniques are developed for the design of ground beds and their resistance measurement. New methods of accurately measuring electrical parameters of finite layered conducting structures are also reported. The effects of stray currents in ground beds is included. Touch-and step-potentials associated with mining equipment are analyzed, and methods are presented for determining earth voltage gradients around structures contacting earth. Instrumentation to determine gradients easily is suggested. Finally, an extensive effort is described dealing with lightning transients on open-pit coal mine ground systems. The nature of the transients, their expected frequency of occurrence, and the ways in which they damage equipment are analyzed in detail.

Jan 1, 1977

By Robert P. Vinson

This Bureau of Mines report presents the results of tracer gas studies conducted at three facilities where bagger hoods had been installed several years ago to remove airborne silica dust from the vicinity of the bagging operator. The studies indicated that for optimum benefits makeup air must be evenly dispersed, the hood enclosures and duct systems must be as airtight as possible, the average intake air velocity of each hood should be at least 200 fpm, and the hoods and duct systems must be properly maintained.

Jan 1, 1981

By Khandaker M. Anwar Hossain

This paper presents the development of lightweight concrete (LWC) incorporating pumice aggregate and volcanic ash (VA) based ASTM Type I blended cement (PVAC). Fresh and mechanical properties of LWC mixtures such as slump, air content, compressive strength, tensile strength, density and modulus of elasticity are described. The durability characteristics are investigated by drying shrinkage (DS) and water permeability. The investigation suggests the production of LWCs incorporating blended PVAC and VPA having satisfactory strength/durability characteristics for structural applications. The use of PVAC induces the beneficial effect of reducing drying shrinkage and water permeability. Development of such non- expensive and environmentally friendly LWCs with acceptable strength and durability characteristics is extremely helpful for the sustainable development and rehabilitation of volcanic disaster areas around the world.

Jan 1, 2010

By E. S. Wheeler

The rapid increase in the use of monel metal and malleable nickel in the form of sheet, rod and tube has resulted in a similar increase in the demand for these metals in the form of castings. These castings range in size from small valves and pipe fittings weighing a few ounces to large centrifugal pumps, gate valves and marine propellers, some of the last weighing as much as 24,000 lb. A group of such castings is shown in Fig. 1. A large nickel agitator is shown in Fig. 2. Monel metal castings are widely used in accessories for steam power plants and in a variety of chemical plant equipment where the corrosion resistance, high strength and toughness characteristic of this metal render it particularly valuable. Nickel castings find extensive use in the construction of corrosion-resistant apparatus, and are often used in conjunction with wrought nickel sheet and tube in the fabrication of equipment for handling a variety of chemical and food products, particularly dairy products. In response to this demand for castings, numerous foundries have undertaken the production of castings of these metals and have met with varying degrees of success. The successful production of castings of monel metal and nickel requires careful attention to molding practice, proper melting equipment

Jan 1, 1930

By Frank P. Frandina, Michael J. Loehr, Paul E. Gabryszak

The Heartland Corridor Clearance Improvement Project is part of a regional Public-Private initiative to allow double stack container trains a direct route from the Port of Norfolk through Virginia, West Virginia, Eastern Kentucky and into Central Ohio. In the Preliminary Engineering stage, 30 existing tunnels were assessed and 28 were found to need clearance improvements to allow the use of double stack trains. Alternative tunnel enlargement methods were developed to achieve the desired clearance improvements, while maintaining structural integrity and minimizing disruption to train traffic. This paper summarizes the geometric and condition investigations of the existing tunnels, as well as describes the preferred methodologies to achieve the desired clearance. The clearance improvements will be implemented beginning in the summer of 2007.

Jan 1, 2007

By C. A. Cole

This work consists of research in cable fault location and the construction of four field-test units based on the research. Swept-frequency sounding of mine cables with RF signals has been the technique most thoroughly investigated. The swept-frequency technique is supplemented with a form of moving target indication (MTI) to provide a method for locating the position of a technician along a cable and relative to a suspected fault. Separate, more limited investigations involved high-voltage time domain reflectometry and acoustical probing of mine cables. Particular areas of research included microprocessor-based control of the swept-frequency system, a microprocessor-based fast Fourier trans-form for spectral analysis, RF synthesizers, transmit-receive switches, RF receivers, cable dispersion-compensation techniques, low-voltage multielement display systems, and techniques for injecting or recovering RF energy through cable walls in support of clamp-on fault locators.

Jan 1, 1982

By L. O. Howard

THERE are three active mines in the Chewelah-Colville district, the United Silver Copper near Chewelah, and the Old Dominion and the Chloride Queen near Colville. The Admiral near Valley is also doing development work. The Chewelah district is in the south central part of Stevens County in the Colville Valley. Chewelah, a thriving town of 1600 people, and the scene of operations of the Northwest Magnesite Co., is about the center of the district. It is situated in a farming community on the Spokane-Nelson branch of the Great Northern railway, about 65 miles north of Spokane. Only two or three of the mines in the district have been extensively developed, although many have been prospected. The general elevation of the valley, is about 1600 or 1700 ft., that of the mountain ranges on each side about 3000 to 4000 ft., with gentle slopes and rounded glaciated tops. Prospecting is often difficult because of much glacial debris.

Jan 1, 1925

By J-S Han, J-M Yao

"An EXTENDED ABSTRACT is available for download. A full-length paper was not prepared for this presentation. The Shagou deposit is located along NE-trending faults within the high-grade metamorphic basement of the Xiong’er Terrane in the Qinling orogenic belt. It is a large Ag-Pb-Zn deposit hosted in the Taihua Supergroup and has proven reserves of 1.54 Mt of ore with grades of 767 g/t Ag, 13.24 per cent Pb and 4.31 per cent Zn. The hydrothermal ore-forming process can be divided into early quartz-pyrite, middle quartz-polymetallic sulfides and late quartz-carbonate stages. Four types of fluid inclusions (ie pure carbonic, carbonic, pure aqueous and aqueous) can be distinguished in quartz. Fluid inclusion, hydrogen, oxygen and sulfur isotope systematics indicate that the ore-forming fluids are initially deeply sourced metamorphic water with meteoric water gradually mixed in the later stages. Sulfur isotope data show that the ore-forming fluids originated from both the Taihua Supergroup and the sedimentary successions of the Guandaokou and Luanchuan Groups (CSC) located to the south of the Machaoying Fault. A genetic model of the Shagou deposit is proposed as follows: CSC subducted northward along the Machaoying Fault beneath the Xiong’er Terrane during the Mesozoic collision between the North China Craton and South China Block. Subsequent dehydration resulted in the devolatilisation of fluids rich in CO2. These fluids migrated upwards, reacted with the Taihua Supergroup and formed the Shagou deposit.CITATION:Han, J-S, Yao, J-M and Chen, H, 2015. Fluid inclusion and isotopic constraints on the mineralisation of the Shagou Ag-Pb-Zn deposit, Henan Province, China , in Proceedings PACRIM 2015 Congress, pp 615–618 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Mar 18, 2015

By M. N. Brodie, John Chapman

INTRODUCTION - DEFINITION & HISTORICAL PERSPECTIVE While this symposium is concerned with comminution which, by definition, relates to all stages of size reduction of an ore body to a form suitable for mineral separation, the electrical drive aspect of the grinding section will receive most attention in contrast to the crushing, screening and materials handling elements of the process. The reason for this is that today's large mills, thirty feet diameter and upwards, present mechanical and electrical problems which require a degree of sophistication in their solution not previously required. The ability to satisfy these demands, so far as electrical technology is concerned, largely results from the development of semi-conductor devices. These can now handle typical electrical distribution power levels within remarkably s m all volumes and with high efficiency when compared with the motor-generator sets, mercury arc rectifiers, rotating amplifiers, magnetic amplifiers and vacuum tubes which were commonly used to provide speed and torque controls as recently as the early nineteen-sixties. The hardware available to the electrical engineer has changed dramatically whereby even the simplest control system formerly using hard-wired relays is now superseded by the program m able logic controller with its computer-like memory containing the sequence of operation, in other words, the software. Reverting now to the mineral process itself, it is assumed that the ore body has been mined using explosives and is delivered to the concentrating plant in its 'run of mine' form. The problem becomes one of reducing the material to a size which will permit an acceptable recovery of the mineral with the most economical use of energy. The size of 'run of mine' material will range from about minus five feet for high tonnage open pit operations to minus two feet for the smaller underground mine. The final reduction in size may range from minus ten mesh to minus two hundred mesh (exceptionally as fine as minus six hundred mesh) depending upon the concentration method and dissemination of the mineral values within the ore. There is no single circuit that satisfies all applications, but the pattern of metallurgical equipment use shown in Table 1 appears discernable from current practice, in general terms.

Jan 1, 1982

By Richard A. Cubeta

Precast concrete segments have been used in sanitary sewer tunnel design for decades. Federal mandates (reduction in heavy metals and I & I), and system design changes (increased retention times) and other factors have exacerbated corrosion problems. In an effort to combat the ever-growing effect of microbiologically induced corrosion, owners, engineers, and designers have been specifying thin-film lining systems to protect precast concrete segments. These systems have compatibility and installation issues. Chemical additives or calcareous aggregates have been utilized in precast concrete, but have only proven to retard the rate of corrosion and do not eradicate the problem. Solid cast polymer segments are stronger than precast concrete, do not require linings or coatings, are impervious to ground water infiltration, and, above all, are inherently corrosion resistant through and through.

Jan 1, 2008

By R. W. Lawrence, J. B. Austin, P. B. Marchant, J. T. Chapman

"Biohydrometallurgy is the use of microbiological reactions to assist in the extraction of metals. Bioleaching offers an innovative alternative for the treatment of refractory gold-bearing sulphides (1). One particular cost advantage of bioleaching is the potential to enhance gold extraction after only partial sulphide oxidation. The apparent selective sulphide oxidation is more prevalent where the refractory gold is associated with arsenic and antimony (2). Oxidation of the pyrite minerals and arsenopyrite at different oxidation rates can result in high gold extractions at relatively low levels of sulphide oxidation due to preferential, or selective, oxidation of the arsenic mineral. Arsenic extraction rates in a bioleach process typically exceed the iron extraction rate. Therefore, in concentrates in which the precious metals are principally associated with arsenic minerals, liberation of the precious metals may be possible with high recoveries and less than complete sulphide oxidation. The capital and operating cost advantages of partial sulphide oxidation are inherently obvious and are briefly illustrated herein.Ultra fine milling (UFM) is another alternative for enhancing gold extraction from refractory sulphides. Some refractory gold is simply particle size sensitive and UFM can improve gold extraction without the need for costly sulphide oxidation (3). Fine grinding technology for enhanced gold recovery developed by Metprotech, South Africa, is currently producing 2 - 4 micron ground product using a single pass, stirred ball mill. Proper application engineering has ensured that plug flow occurs through the mill. Plug flow from the feed inlet at the bottom of the reactor ensures that short circuiting of feed does not occur and as a result, the mill product does not require classification.A combination of UFM as a pretreatment for bioleaching could provide a mechanism for enhanced selective sulphide biooxidation and/or increased overall gold extraction following biooxidation due to improved particle liberation ( 4). The effect of UFM on biooxidation costs will be discussed. Only sulphide concentrates are considered herein for application of UFM in combination with biooxidation."

Jan 1, 1990

By John Ellenberger

The National Institute for Occupational Safety and Health (NIOSH) has collected pillar and span data at 34 stone mines in 10 states to develop pillar and roof span design guidelines for underground stone mines. Pillar, floor and roof conditions each contribute significantly to the overall mine stability. The roof may be stable for a century, or it may appear to be stable but fail with little warning. Clearly, an assessment of the mine roof is critical to the safety of these operations. However, up until now, the assessment of the mine roof came primarily from exposures in roof falls or portal areas. This provides only limited information, and a more proactive approach is needed to assess changing mine conditions. A separate effort was undertaken to examine the roof structure with the use of a borescope. Numerous physical and geologic roof structures were observed with a stratascope/borehole video camera. The objective of this work was to develop a technique of assigning numerical values to features seen within the mine roof and apply those values to formulate a roof stability evaluation. Such features as changes in color, grain size, and general lithologies are readily observed. Minor structures in the rock, fossils and fractures are also readily identified. Each feature may have a variable and site-specific impact on roof quality. A number of mines were visited and a series of holes were borescoped in each mine. The features identified in the roof were classified and potential for roof damage related to each feature was assessed. A process is presented that relates the structures and their locations to provide a numerical value, or roof quality index that can be used to assess roof stability.

Jan 1, 2009

By James A. Finch

"I offer a personal view of what the next 30 years holds for mineral processing. Re-stating that mineral processing will remain a vibrant industry in raw material production, growth opportunities in waste management are identified. The processing sequence familiar now (mining -mineral processing -extraction) will become more interwoven. In situ processing (i.e., milling underground) will evolve from concept to demonstration. Opportunities to exploit physical properties altered in chemical (pyro-and hydro-) processing will present themselves. In primary grinding, the path to AG/SAG milling will progress with little deviation but opportunities in regrinding are wide open. Flotation will see the trend to designing bubble/particle reactors accelerate simultaneously with a vigorous response from mechanical cell suppliers. Gravity separation remains a bastion of the lone inventor but I anticipate that the new lines will come from the waste management business. I finish by examining the ""research cycle"", identifying growth in small ""high tech"" companies and university research centres.IntroductionI have been asked to offer a personal view of""where we are going in mineral processing?"". Gazing into crystal balls is quite a cottage industry as we approach the end of the millennium. Academics are often asked to assume the role of visionary, I presume because it is considered in their mandate, to reflect and philosophize (or, less charitably, because they are considered to have the time). Since this is the 30th Annual Canadian Mineral Processors Operators Conference, I am tempted to suggest the next 30 years as my frame of reference. This is about equivalent to one engineer's career or, given it takes typically 15 years to go from concept to realization in mineral process engineering (Napier-Munn, l 997a), about 2 ""invention cycles"". With this length of cycle, much that is familiar now will remain so over the 30 years.Research and development (R&D) is in response to need. The overarching need in mining is to find new ore bodies. Process developments cannot compensate for a depleting deposit or a declining commodity price. Mineral processing R&D is characterized by incremental gains, aimed at pushing the mine down the cost per tonne league table. Breakthroughs are the exception (flotation at the turn of the century was one). This must be kept in mind when trying to predict the future in our business."

Jan 1, 1998

By Andrew Kaczmarek

The mining industry is enjoying a much needed and long awaited increase in demand for natural resources. However, consolidations in the mining and mining service industries, along with a generational departure of experienced industry professionals, is challenging today’s mining companies. These challenges are not only in maintaining their existing operations, but also in securing qualified resources for developing new projects. These challenges are compounded for junior mining companies. They oftentimes lack for operating properties to draw experienced professionals from. Also, juniors have to compete with the majors’ “mega-projects” for experienced project personnel from the reduced ranks of engineering companies. This article discusses some strategies developed by Anatolia Minerals Development (Anatolia) in developing its Çöpler gold project in central Turkey.

Jan 1, 2006

By Frances H. Clark

DEVELOPMENTS in powder metallurgy have been disappointing in 1943. If any new part has gone into large-scale production, knowledge of it has been restricted by considerations of national security. Nor have any outstanding papers appeared to advance the theory of the subject during this period.

Jan 1, 1944

By E. Wasmund

"Sandfire’s DeGrussa Copper-Gold operation in West Australia is a new high grade copper sulfide mine, which includes a 1.5 Mtpa concentrator which was completed in 2013.Early after commissioning, it was identified that the flotation capacity in the all-mechanical cleaner circuit was not sufficient. In order to improve recovery, the tail from the cleaner scavenger was sent back to feed the rougher scavengers. Test-work was done on-site to evaluate the possibility of using a flotation column as a pre-cleaner. A CavTube™ sparging system was selected, which is especially effective for fine ore particle flotation. Test-work was conducted at site using a 150 mm diameter unit, and then confirmed on a 500 mm diameter unit. A 4250 mm diameter full scale unit was installed in Q4 2014 and commissioned in Q1 2015. This unit gave some significant advantages including a reduction in re-grinding requirements, elimination of a circulating load and increase in the recovery of copper in the cleaner circuit and overall circuit.In this presentation, the benefits of columns and cavitation sparging for floating fine particles and rejecting fine entrained gangue will be explained. Also, the results from a lab unit and a pilot unit will be compared against the results of the full-scale unit. The paper will demonstrate the scalability of flotation columns, and which phenomena and scale-up criteria must be considered to be successful. Finally, some general observations will be made about the importance of columns in copper cleaning circuits.IntroductionSandfire Resources’ DeGrussa copper-gold concentrator is located approximately 900 km north-north-east of Perth in Western Australia. The project area landscape is scrubby mulga lands with few notable features. The climate is arid with high temperature and heavy summer downpours."

Jan 1, 2016

A general description of investigative work conducted by the Bureau of Mines at the, Missouri Valley. manganese deposits and leading to tonnage and grade estimates has been given in Report of Investigations 4375, part 1 of a three-part report of work done between July 1945 and August 1947. Basic factual information from which tonnage and grade estimates were drawn was derived through the drilling sampling of 238 large-diameter bucket-drill holes in 11 widely separated areas. Drilling areas were selected after careful reconnaissance, mapping, and consideration of earlier work done on the deposits by the Bureau of Mines, State agencies, and private organizations and individuals. Stratigraphic studies permitted extending the results compiled within the drilling; areas to outcrop and lightly covered manganiferous zones between an beyond drilling areas. The locations of drilling areas, drilling sections, and individual drill hues are shown on illustrations in part 1 f this report. The individual drill holes, aside from providing the basic information for tonnage and grade estimates, disclosed features affecting any future plan As exploitation. It in particularly significant that a large part of the visible outcrops is faulted end otherwise complicated by slides that give a false impression of the thickness, vertical location, and even the existence of manganese-bearing zones.

Jan 1, 1949