Search Documents

By Jouko L. Lehtonen

Sheet pile walls can be sealed watertightly using various methods. The objective of this paper is to introduce a new innovation comprising the use of continuous cement grouting during embedding. The method has been tested on a field test site and installation and permeability features have been observed and analyzed. Installation can be carried out using traditional sheet piling machinery, merely some additional grouting equipment is needed. Installation speed of grouted sheet piles corresponds to that of conventional embedding. The permeability of the tested method is satisfactory in applications where e.g. polluted soil or water has to be isolated from the surrounding environment. In addition, this method can be used for conventional retaining walls where very low permeability is required or for reduction of soil vibration, e.g. close to a railway embankment. The new method to grout simultaneously and continuously during embedding has been developed based on respective innovations on impact driven steel piles.

Jan 1, 2006

By J. D. Potts

Dust surveys were conducted at six underground coal mines to determine if deep-cutting practices expose face workers to higher levels of respirable dust. The surveyed mines were able to successfully mine deep cuts without significantly increasing the dust exposures of face workers. For exhausting face ventilation, field data indicate that scrubber airflow is the most important factor for controlling dust. Data collected for this study indicate that 20-mesh screens should be cleaned for every 40 ft of advance because 22% of the deep cuts surveyed for this study experienced a 20% to 35% decrease in scrubber airflow over the course of the cut. For blowing face ventilation, field data and past research indicate that dust control is aided by maintaining a proper curtain-to-scrubber airflow ratio of 1.0 (measured before scrubber activation) as well as a curtain setback distance that allows the miner operator to stand at the mouth of the curtain for the entire cut. Dust levels on the bolting faces did not appear to be affected by the longer cycles associated with deep-cut mining when good ventilation practices were used.

Jan 1, 2011

By Doug Anderson

Blast vibration seismograms are generally collected strictly for compliance with regulations. The peak levels (including dominant frequency) are typically all that are looked at. However, these records contain a lot more information about how a blast has performed. The seismogram is actually a record of explosive energy that was not used in fragmenting rock. The trick is to determine how to extract information that would be useful in analyzing blast performance.

Jan 1, 2013

By John Capers

•The IME is the Safety and Security Association of the commercial explosives industry in the United States and Canada. •Founded in 1913 •Board of Governors •5 Standing committees- 1. Technical 2. Environmental Affairs 3. Legal Affairs 4. Safety & Health 5. Transportation & Distribution

Jan 1, 2006

By W. A. McKinney

The segregation process consists of heating crushed oxidized or mixed oxide-sulfide copper are with a copper-volatilizing salt and carbonaceous material at about 750° C. to produce metallic copper which is recovered from the furnace calcines by conventional sulfide flotation. The Bureau of Mines made a number of bench-scale laboratory tests on two copper ores to determine the relative merits of using halogen salts, potassium chlorate, or various salt mixtures as volatilizing agents in segregation of the copper. Laboratory investigation of typical siliceous and calcareous oxidized ores revealed that sodium chloride was a better segregating agent than the other salts. Calcium chloride, magnesium chloride, sodium fluoride, or potassium chlorate gave nearly as good segregation as the sodium chloride on the siliceous ore. Segregation of the calcareous ore with calcium chloride was nearly as good as that obtained with sodium chloride, but inferior segregation resulted when magnesium chloride, sodium bromide, or potassium chlorate was employed. The use of sodium bromide or sodium iodide on the siliceous ore, and of sodium fluoride or sodium iodide on the calcareous are, gave appreciably poorer segregation than sodium chloride or the other salts. Other tests of the ores, using mixtures of sodium chloride and the other halogen salts or potassium chlorate, gave segregation approaching that obtained with sodium chloride.

Jan 1, 1962

By L. Xinghua

Limonite is a general term for a group of amorphous iron oxide and iron hydroxide materials. It is considered as one of the very refractory iron ore types due to its wide variation in chemical composition, iron content, moisture content and easily sliming in the course of comminution. Iron grade of test sample is 25.48%, the iron minerals are mainly limonite; and the gangue minerals consist of quartz and feldspar in majority, secondarily silicate minerals. In this test work, high intensity magnetic separation (HIMS)-cationic reverse flotation and magnetic roasting-low intensity magnetic separation (LIMS) tests were conducted on limonite ore. The test results show that the concentrate with iron grade of 50.97% and recovery of 68.50% can be obtained by HIMS-cationic reverse flotation technique; while using magnetic roasting-LIMS technique, the better concentrate indexes of iron grade of 60.36% and recovery of 89.71% are achieved, and the iron grade of tailing is only 4.42%. Therefore, the magnetic roasting-LIMS technique is a better suitable method for beneficiation of low-grade limonite ore. Keywords: Low-grade limonite; Mineralogy; HIMS; Cationic reverse flotation; Magnetic roasting; LIMS

Feb 27, 2013

By Xu Lin Sheng

During the mining course, when the roof above coal seams is constituted by thick and hard sandstone (conglomerate), sudden roof movements often take place with great force and de¬struction which is the biggest danger to the safety and production. Such sever movements of the roof in mining directly relate to the rock mechanical properties which are the main fac¬tors that influences the regularity of hard roof movement and its destruction form. A significient work and important technical way for applying rock mechanics into mining en¬gineering is studying the rock mechanics of the hard roof and altering some of the rock me¬chanic parameters which induce the improvement of the rock properties in order to efficiently control the movement of the hard roof.

Jan 1, 1989

Validation of the JKMRC Rotary Breakage Tester (JKRBT) Ore Breakage Characterisation Device

Sep 13, 2010

By Roy Woodall

Successful mineral exploration is the lifeblood of the mining industry. Contrary to what the environmental lobby would have the world believe, the industry is replacing the metals it is extracting. The reserve base has not changed significantly in 20 years (Fig. 1.) Mineral exploration is a research activity. First there is the idea, the vision or the intuitive thought. The experiments follow. These involve repeated phases of data gathering, data interpretation and concept testing through drilling. For many companies, exploration is the main investment in scientific research. Each mineral exploration experiment may involve years of costly work. Despite the improving tools of science and technology, the investment remains high-risk. Only the promise of high rewards, or desire to survive as a mining company, will stimulate the necessary commitment and level of investment. Confidence that an economic return can be achieved, confidence in the science and technology being applied and confidence in the people involved are the foundations upon which successful mineral exploration is built (Woodall, 1984). The challenges facing the explorationist in the 1990s fall into two categories: - the challenge to make the activity economic; and - the challenge to make the activity socially and, therefore, politically acceptable.

Jan 1, 1992

By J. Lovering, M. Allan

"INTRODUCTIONThe Afton Mines property is located 180 air miles east-northeast of Vancouver and nine miles west of Kamloops, a city of 60,000 people in south central British Columbia. The deposit is located adjacent to the Trans-Canada Highway at an elevation of 2,231 feet above sea level.Interest in the property dates back to 1898, when a 330 foot shaft was sunk on the Pothook claim immediately south of the existing operations. Since that time many companies and individuals have investigated the possibilities of the area but it was not until 1972 that Afton Mines Ltd. located a significant zone of copper mineralization. The feasibility study was completed in the period 1974-1975, by Teck Corporation Ltd., who control Afton through 50% direct ownership and 65% ownership of Isa Mines, who own a further 23%. Construction began in March, 1976. Ore production started in August, 1977, and the first ore was fed to the mill on December 8. This was the third mine to be brought into operation by Teck since 1975, the others being Newfoundland Zinc and Niobec.The orebody is a porphyry copper deposit which has undergone supergene alteration. It is 1,700 feet long in a west-northwest by east-southeast direction, 300 feet wide and dips at 55° to the south. The mineralization in the supergene zone, which accounts for two-thirds of the known deposit, is rather unusual in that the copper is present primarily as native copper and chalcocite. The grade is one percent with the distribution: 70% native, 25% chalcocite, and 5% chalcopyrite with bornite, covellite, and cuprite."

Jan 1, 1979

By David R. Jessey

Water pollution problems associated with surface metal/nonmetal mines throughout the United States were assessed. Three major problems were identified: acid mine drainage (AMD), toxic concentrations of heavy metals and excessive sedimentation. Several factors affect the type and amount of pollutants generated at a mine site. Among these are hydrologic regime, geology, mineralogy, topography, climate, size of the mineralized area and mining method. Nine surface mines situated in distinctly different settings were visited and their pollution problems studied. These mines were located in Morenci, Arizona; Hayden, Arizona; Sauharita, Arizona; Cobalt, Idaho; Spruce Pine, North Carolina; Iron Mountain, California; Butte, Montana; Fernwood, Idaho; and DeLamar, Idaho-Oregon. A detailed evaluation of the pollution problems at the Morenci mine indicated that a diversion system and treatment pint would be the most effective means of abatement for the existing water quality problems. Based on the study of the Morenci mine and three other porphyry copper mines with differing problems a water management plan was conceived for a new source copper mine. A companion Appendix Volume containing detailed reports on the mine site visits is on file at the US Bureau of Mines Spokane Research Center.

Jan 1, 1981

Alluvial gold mining in New Zealand and in particular on the West Coast underwent a renaissance during the early 1980's. This was based on two main factors: a) the sharp rise in the gold price b) the advent of the hydraulic excavator with which to mine the auriferous gravels. The scale of operations varies considerably. A small operation typically consisting of one or two people using an excavator to feed either a land based or pontoon mounted (floating) gold recovery unit, which will typically feature a rotary screen with or without a tailings stacker with the screened fines < 10 - 15 mm) fed over riflle tables. The largest screening plants of this type are operated by DML Resources in their Arahura and Mikonui mining operations where the plants have the capacity to screen up to 250 m3 of gravel per hour. These plants usually employ jigs and centrifugal concentrators for gold recovery. Unique amongst current operations is the Grey River Dredge, a bucket ladder dredge capable of processing 700 m3 per hour similar to those that operated earlier this century. Gold concentration is by a series of jigs. The number of plants operating in recent times peaked at around 130 in 1987 (coinciding with a nominal average gold price of $751) and since that time has steadily declined to 80 units in 1993 and about 45 - 50 units today. This cycle of rapid expansion and then steady decline has been repeated on the West Coast since the original gold discoveries in the mid nineteenth century.

Jan 1, 1996

By Gungor Tuncer, Ali Kahriman, Abdulkadir Karadogan, Mehmet Aksoy, Kagan Ozdemire

With increasing environmental constraints on the levels of disturbance induced by blasting operations upon nearby residents, there is an increasing need to be able to design cautious blasting with greater precision. Therefore, determination of maximum amount of explosive per delay for a certain distance especially in large blasts is of great importance for the elimination of these environmental problems. Although too many research studies had been carried out in the past in order to eliminate environmental issues produced from blasting unfortunately a general approach or formula has not been established yet because of the complexity of the matter. In addition to the wave and ground motion characteristics, the complexity of blasting parameters and site factors restrict the developing a general criterion. So experimental site-specific studies should be still done in order to predict and control blasting effects. This paper presents the results of ground vibration measurements carried out in Espey Open-Pit Boron (Colemanite) Mine located on the west side of the central Anatolia near Kütahya province in Turkey. Within the scope of this study, ground vibration components were measured for 13 shots during bench blast optimisation studies in order to predict peak particle velocity level for this site. In blasting operations; ANFO and Powergel Magnum 600 (blasting agent), Powergel Magnum (priming) and delay electric detonators (firing) were used as explosives. Parameters of scaled distance (charge quantity per delay and the distance between the source and the station) were recorded carefully and the ground vibration components were measured for all blast events using 4 different types vibration monitors (3 White Mini-Seis and 1 Instantel Minimate Plus Models). Then, the data pairs of scaled distance and particle velocity obtained from the 38 record events were analysed statistically. At the end of statistical evaluation of the data pairs, an empirical relation which gives average line at 95% confidence level and upper bound 95% prediction line with a reasonable correlation coefficient was established between peak particle velocity and scaled distance.

Jan 1, 2005

By H. Kose

In this research, a model quarry with an annual production capacity of 1 000 000 tonnes has been studied for both pit and hillside quarry cases with constant overall slope angle and variable bench slope angle, considering road grades of 8 per cent and 10 per cent. First, technical requirements have been determined and then the effect of production parameters, such as hole diameter, type of quarrying (pit or hillside) and road grade, on the cost has been investigated to determine bench height. Based on the results, it has been concluded that hole diameter has to be kept large in both pit and hillside quarrying to reduce drilling unit costs. In addition, in order to take advantage of gravity and reduce transportation cost, it has been suggested that bench height and road grade have to be kept high and low respectively in the case of hillside quarrying (downhill transportation) while, in the case of pit quarrying (uphill transportation), bench height and road grade have to be kept low and high respectively, in order to transport the blasted material to a lower height and distance, to save energy, thus decreasing the transport cost. Keywords: Quarry, pit, hillside, road grade, bench height

Jan 1, 2005

By J Canterford

There is an apparent push to develop and commercialise "new and innovative" process flow sheets. A not-too-difficult reality check clearly demonstrates that the success rate of this push is not particularly significant and in fact could be regarded as a waste or misappropriation of R&D funding and the associated brain power. As Julian Sumner Miller would comment "why is this so?" To put it bluntly, many of the so-called innovative developments are equivalent to gold plating the dunny door - visually interesting but of very limited practical value. This presentation encapsulates some personal lessons learnt over the past 45 years.CITATION:Canterford, J, 2013. Developing a ænew and innovativeÆ process flow sheet - Traps for all players of all ages, in Proceedings MetPlant 2013 , pp 1-5 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 15, 2013

The polymerisation of silica is found to interfere with thickening of leach pulps at Risdon. Hydroxyl ion and fluoride ion are catalysts for this reaction. Stability may be obtained by the presence of aluminium or ferric iron.INTRODUCTIONAt Risdon it has been a matter for satisfaction that, although the concentration, of silica in leach solutions is appreciable, it has ,given relatively little cause for anxiety.However the margin of safety is small and some intermittent difficulty in thickening leach residues during the last few years has prompted a further investigation, certain parts of which are described here since they may be of general interest.Leaching and ClassificationThe method of leaching which is practised at Risdon has been described in, two previous articles, by W. C. Snow (1936) and S. W. Ross (1949) to whiCh the reader is referred for detail. Continuous leaching is practised, the circuit solution flowing through five air agitated pachucas in series, to tlie first of which calcine is added. The circuit solution, which also enters the first pachuca, consists of spent electrolyte from, the electrolytic cells and contains 90 -gm. of free sulphuric acid per litre. About 80 per cent of the solublezinc oxide is extracted from the calcine in the first pachuca, at a pH value of 1-1 (7 gm.H2S04/1 at 55 to 60°C. In the later pachucas the leaching rate decreases sharply. The leach pulp which leaves the 'last pachuca contains an average of 17 gm. of free acid per litre, corresponding to a pH of 1.7; but, owing to variations in extraction, the end point fluctuates between 2.5 and 0·3 gm. free acid per litre (pH:> 1·5 to 2.5). The average flow through the plant is 1,250,000 gallons per day, which corresponds to a production of 300...

Jan 1, 1958

By Robert Stefanko

The growing demand for energy during the post World War I and World War II periods has prompted underground coal production to increase rapidly. This has been met primarily by mine mechanization, resulting in the development and application of new mining machine types. Correspondingly, the total connected horsepower of each machine as well as the number employed has enlarged rapidly since 1950. (2,3,9,14,16,17) Electrical consumption for each mine has also grown. In the early years of mining electrical applications, only d-c power was utilized underground. Yet, d-c machine limitations were soon realized, and many a-c systems were substituted to permit economic and efficient utilization of a-c distribution and motors. Due to the attractive torque characteristics, ease of distribution and speed control, several traction applications have continued to be powered by d-c motors. The result has been the now prevalent use of mixed a-c/d-c mine power. However, augmented electrical power employment seems to have added to underground coal mining electrical accidents.

Jan 1, 1974

By Chas. F. Jackson

The work of the mining division is divided between seven sections, each in charge of a supervising engineer, as follows: 1. Metal-mining methods section, the supervising engineer of which is also supervising engineer of the Southwest Experiment Station at Tucson, Ariz. 2. Metal-mining research section. 3. Nonmetal minim section. 4. Coal-mining section. 5. Mine-ventilation section. 6. Mineral-industries survey section. 7. Electrical section. The names of the sections indicate broadly the fields covered by each, and in the following pages the objectives and type of work of each section will be summarized briefly and the active problems listed. The work done during the calendar year 1936 will also be summarized.

Jan 1, 1937

By W. R. Hardwick

This paper describing the mining methods of the Inspiration Consolidated Copper Co. is one of a series being prepared by the Bureau of Mines on mining methods and costs in various mining districts of the United States. The story of mining at Inspiration is of particular interest because, after 127,812,000 tons of low-grade copper ore were successfully mined, the mining method was changed from block caving to open-pit. As the open pit became deeper, many features of the former block-caving operation that were exposed elucidated concepts of the mechanics of caving that previously had been assumed but not observed. The conversion to open-pit mining was accomplished by unique combinations of equipment and the introduction of ingenious engineering and operating practices that have extended the expected life of the mine for many years.

Jan 1, 1963

By R. J. Wensley

THE use of small substations for the supplying of 275-volt energy to the locomotive and cutting machines in coal mines is a well-established practice. A few years ago, when labor costs were lower, these substations were located as near to the load as possible, and an operator was provided for each station. This practice has now become so expensive that substations are being located with reference to other mining machinery, such as hoists or pumps, so that one operator can look after both. Some-times the substation is operated by one whose duties make him traverse quite a large area. In such cases the interruption of alternating-current supply may produce a long interruption in the direct current, as the station cannot resume service until this man reaches it. Such interruptions interfere seriously with production and may easily counterbalance the supposed saving gained by such operating methods. The grouping of substations for convenience in operating may also result in excessive copper loss and consequently poor trolley voltage, with its attendant evils of low locomotive speeds and increased locomotive motor maintenance. The speed of the coal-cutting machines will also be reduced. By relieving the substation of its, burden of the operating labor cost, the most economical location, from an electrical standpoint, may be chosen. The matter of machine insurance should also be considered. If an attendant is caring for several kinds of equipment, he cannot watch the machine continually for signs of trouble; therefore, continued overload, phase failure, low alternating-current voltage, bearing trouble, etc. may result. Some partly automatic equipments have been installed; these have protection against low voltage, reverse current, and bearing trouble and are provided with automatic reclosing circuit breakers. This is a step in the right direction but it does not go far enough to give first-class machine insurance.

Jan 9, 1921