Search Documents

By J. P. Jarrell

Environmental considerations are of increasing importance in determining the acceptability, schedule and cost of expansion ofCanada's uranium processing industry. Environmental considerations must be addressed in the early stages of facility planning. This results in a dilemma, as the process data needed to predict physical environmental impacts are not yet available from process design activities. Hence, a business risk is incurred if plant design is carried forward to meet these requirements prior to project (or site) approval. On the other hand, project scheduling normally mitigates against leaving process design engineering until such time as project approval is obtained. This paper examines the experience gained in Eldorado Nuclear's proposed expansion of refining capacity as viewed by an environmental engineering consultant. The history of the project and the relationship to process design functions in the two-year period prior to the Port Granby environmental hearings are reviewed. During the Port Granby public hearing, there was a consensus that normal operation of the proposed refinery could be successfully integrated with the site's natural environmental constraints. Moreover, the radiological impact from plant operations was demonstrated to be inconsequential. However, concerns were raised relating to plant upset and accident situations. These concerns are summarized. Process data requirements identified during the environmental hearings are discussed. Finally, the concerns for on-site burial of radioactive waste are reviewed. These concerns focussed on long-term stability of the waste in the presence ofgroundwater transport, erosion and glaciers. The AECB's position on waste management with regard to this project is reviewed in light ofthe implications for design.

Jan 1, 1979

By Xuan Li

Aluminum slag is generated when aluminum metals are recycled through a smelting process in the presence of salt. There are small amounts of aluminum metals trapped in the aluminum slag. This research aims at evaluating the use of aluminum slag as an expansion agent for the production of lightweight concrete by taking advantage of the residual aluminum metals in the slag. The research identified key elements of producing lightweight concrete products through utilizing various mixture components including sodium hydroxide (NaOH), lime (CaO), cement, and gypsum. The volumetric expansion rate was investigated and the density and strength of the products were determined. The results show that aluminum slag can be utilized for the production of lightweight concrete products.

Jan 1, 2010

By Stefan Basista, Janusz Tomala

Modern constructions of electric ferroalloy furnaces are still based on applying in the lower "liquid" areas the standard carbon materials. What can be illustrated by the experience from several years, in the part of tap hole, hearth walls and bottom, is that so-called carbon or semigraphite microporous materials are successfully being applied. These materials, compared to the standard carbon, give better resistance to the attack by liquid metal and other wear factors. Generally this group includes materials characterised by considerable share of pores of diameters below1µm (significantly exceeding 90% of total porosity). The microporosity increases the resistance to the infiltration of the liquid metal. The effect of microporosity can be obtained by introducing silicon (or its compound) additive to materials based on electrically (or gas) calcined anthracites, electrographite and binder. Moreover, by introducing other ceramic additives, the microporous materials are more resistant to dissolution by the liquid metal. Observing the trends of "improving the materials" in the last years, it is clearly seen that the share of non-carbon additives is bigger and bigger, so we can reasonably speak of rather carbon-ceramic materials. In this paper, the survey of the most important quality criteria, which must be met by the carbon furnace linings, as well as the new testing methods will be presented.

Jan 1, 2007

A study of literature on the epidiorite dykes which transgress the Broken Hill lode and its wall rocks reveals a considerable diversity of thought regarding the time of emplacement of such dykes. In this paper it is deduced that the epidiorite dykes were formed at a late stage and were probably post-ore. Detailed mapping, sampling, and correlation of data from over 100 exposures substantiates this deduction. Physical disruption of the epidiorite dykes is indicated and some interaction of the epidiorite and ore at the time of intrusion is inferred.Further petrological study may confirm this.

Jan 1, 1968

By Louis Schaffer

A literature review concerning dredging hazards and dredge safety practices and an examination of MSHA accident and injury statistics on dredge mining in the United States provided the background for an analysis which was completed by visiting 31 dredge operations, dredge manufacturers, and dredging experts. The principal hazards are discussed and countermeasures are suggested in several areas. Drowning is the single largest fatal injury category. Special emphasis is given to the design, care and use requirements of personal flotation devices.

Jan 1, 1984

THE Synthetic Liquid Fuels Act (30 U.S.C., 321-325, and amendments) became law April 5, 1944, and a period of intensive research and development in this field was begun by the Federal Bureau of Mines. As part of this program, bulletins were published on pressure hydrogenation,3 the Fischer-Tropsch synthesis,4 and nil stifle.5 The. Bureau also has published a short bibliography on coal gasification,6 mostly of a theoretical nature. Because anal gasification is prerequisite to either the Fischer-Tropsch or coal-hydrogenation processes, publishing this sizable collection of technical information in this form Will Ire valuable. The material will he presented in three parts. as follows I. United Stares Patents. II. United Kingdom, Australian, Canadian, and South African Patents. III. Other Foreign Patents. Part I appeared in early 1960. Part II follows.

Jan 1, 1962

By A. B. Hazar-Yoruç

Ferrochromium produced by smelting chromite ores is an important alloying component in the steel industry. Ore, coke and fluxes are mixed and reacted in an arc furnace for a smelting process of ferrochromium. In ad-dition to this process, pre-reduction of chromite ore with carbon is an important industrial process. In all these processes, the mechanism and kinetics of reduction of chromite with carbon play an important role. In this study, the reduction of Turkish chromite ore with carbon was investigated. Chromite and carbon were ground to three different particle size groups. Chromite was mixed with carbon in stoichiometric and excess ratios. The samples were reduced under argon atmosphere at temperatures between 1,200° and 1,350°C. The formed phases and alloy compositions of reduced chromite samples were analyzed by optical microscopy, scanning electron microscope (SEM) with EDAX and X-ray diffraction analysis (XRD). Experimental results showed that the degree of reduction and the reduction rate increased with increasing temperature and decreasing particle size. The highest degree of reduction, 61.4%, was obtained at 1,350°C. The reduction took place in three stages: Stage 1: transformation of Fe3+ to Fe2+ and formation of metallic nuclei, Stage 2: formation of metallic crust around the particles and Stage 3: growth of the metallic crust and coalescence of the metallic phase.

Jan 1, 2007

By Ahmad Ghahreman, Lin Li

Silver and cupric ions have been proven to play the roles of catalysts to promote the oxidation kinetics of chalcopyrite in acid solution. In this study, the interaction between silver ions and cupric ions during ferric leaching of chalcopyrite in sulfuric acid solution has been investigated. The electrochemical study by Tafel analysis showed a significant boost of dissolution rate for chalcopyrite dissolution in Fe3+- Cu2+ containing sulfuric acid solution after Ag+ was added in the solution. For 10 ppm Ag addition, the dissolution rate of chalcopyrite increased to 7.94 ×10-6 A/cm2 from 3.2 ×10-7 A/cm2, when Ag+ was absent. On the other hand, the effect of Cu2+ on the dissolution of chalcopyrite in Fe3+-Ag+ containing sulfuric acid solution was not obvious from electrochemical measurements. The chalcopyrite leaching tests in different acid solutions showed that silver addition had an obvious catalytic effect on promoting chalcopyrite dissolution. Comparing the leaching rates of chalcopyrite leached in Fe3+ containing, Fe3+-Ag+ containing, Fe3+-Cu2+ containing and Fe3+-Cu2+-Ag+ containing sulfuric acid solutions, it was found in Ag+-Fe3+-Cu2+ containing sulfuric acid solution, the leaching rate was highest among all the aqueous acid systems. Further leaching tests suggested that with increase of the Ag+ concentration from 0 to 20 ppm, the leaching rate of chalcopyrite in Ag+-Fe3+-Cu2+ containing sulfuric acid solution also increased and reached 57.62% with 20 ppm Ag+ addition after 24 h. INTRODUCTION Chalcopyrite is the most important copper mineral in copper hydrometallurgy and it accounts for nearly 80% of the universal copper resource (Olvera, Rebolledo, Mora, Dixon, & Asselin, 2018). The hydrometallurgy of chalcopyrite has been intensively studied with emphasis on solving the slow dissolution kinetics of chalcopyrite in acid environment. A variety of aqueous systems, such as sulfate (Hiroyoshi, Miki, Hirajima, & Tsunekawa, 2001), chlorides (Liu, Chen, & Yang, 2017), and ammonia (Hua et al., 2018) have been studied to improve copper leaching. From another perspective, chalcopyrite leaching studies have indicated that the mechanism of chalcopyrite dissolution in acid solution is essentially electrochemical (Li, Kawashima, Li, Chandra, & Gerson, 2013). Therefore, extensive studies have recently been carried out to explain the dissolution kinetics of chalcopyrite in different media by various electrochemical techniques.

Jan 1, 2019

By C Jia, J Graindorge, L M. Olssen

Picking up abandoned mining tenements and looking to recover remnant resources around old operations is an opportunity that comes with its own challenges and risks. Reliance on information released to government departments (such as the Department of Mines and Petroleum (DMP) in Western Australia) by the previous owners, can compound the risk.This paper explores Alto Metals Ltd’s Lord Nelson and Lord Henry deposits and surrounds near the town of Sandstone in Western Australia. The Lord Nelson and Lord Henry open pits produced around 2 Mt of ore for over 250 koz of gold during production between 1999 and 2010. There has been no further work carried out in the area between 2010 and 2016. The deposits are open at depth and along strike.Alto Metals picked up the tenements in 2016 and has subsequently re-estimated remnant resources around Lord Nelson and Lord Henry, and publicly reported updated Mineral Resources in accordance with the JORC Code 2012.All of the information was manually compiled from data released to the DMP and annual reports. This paper highlights the challenges and risks arising from this data compilation, geological interpretation, re-estimation and classification process, together with future opportunities and challenges for further developing the area.CITATION:Olssen, L M, Graindorge, J and Jia, C, 2017. Starting from scratch – defining remnant resources from publicly available data: a case study from the Lord Nelson and Lord Henry gold deposits, in Proceedings Tenth International Mining Geology Conference 2017, pp 175–188 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 20, 2017

By Edmund J. Cardoza

The paper describes the design, construction and quality control aspects of the installation of a cement-bentonite (CB) cut off wall to impede seepage through a flood control dike. Special emphasis is placed upon the development of a proper specification, distinguishing the CB method from the Soil-Bentonite technique. The importance of the pre-construction laboratory testing program and field quality control procedures is emphasized by the fact that the in-place properties and characteristics of the CB cut off may not be known until after a majority of the work is complete. Sections are included which describe the construction method, the specialty equipment and personnel requirements and the quality control/quality assurance aspects of the project.

Jan 1, 1992

By R. F. Hinds

A pressurizing system was designed and built to apply a radial pressure of 5.000 psi to rock samples. Samples of the Bradford, Weir and Kirkwood sandstones were subjected to radial pressures parallel and perpendicular to the bedding in the system and the changes in conductivity, porosity and permeability were deter-mined. Asymptotic decreases in conductivity, porosity and Klinkenberg permeability were observed over the 0- to 3,500-psi range. From these data, the increase of formation factor over the same range was calculated. The cementation exponent expressed in the Archie equation was found to increase with pressu,re. The rate of change varied from formation to formation. Only small differences were observed for samples taken parallel to the bedding as comnared to those taken perpendicular to it except for the Bradford sand. Above 3,500 psi the data are not good enough to tell if the properties continue to fall-off asymptotically or in a different manner. A possible explanation for the probable litnit of the asymptotic rate around 3,500 to 4,500 psi is that this represents the maximum pressure which the formations have unrdergone during their geological life as a result of burial. INTRODUCTION For many years measurements have been made in the laboratory of the properties of oil-bearing sandstones with little consideration being given to whether these properties had been changed when the samples were moved from their original position in the ground to the laboratory. Relatively little has been reported in the literature on the effect of pressure on the properties of sandstones. The changes in permeability for eight typical consolidated oil-bearing sandstone samples with overburden pressure (0- to 15,000-psi range) was presented by Fatt and Davis' in graphical form. In 1953 Fatt' also reported the relationship between porosity and overburden pressure for four typical consolidated oil-bearing sandstone samples (0- to 5,000-psi range). Fatt later described the changes of formation factor and porosity of 20 typical oil-bearing sandstone samples with overburden pressure changes (0- to 5,000-psi range) giving the values of the coefficients and exponents in the Archie' equation, and the more general Winsauer equation', where C, k and m are empirical constants, F is the formation factor, and + is the porosity. During the experiments of this investigation the core was contained in a neoprene rubber sleeve as shown in Fig. 1. It was held between two steel end members which were mounted in a steel cylinder. The unassembled pressure cylinder with its component parts is shown in Fig. 2. The core was insulated from the two steel end members by a Teflon sleeve with a small hole in the

Particle Size Measurement of TiO2 Nanoparticles in Non-Aqueous Solvent by Interactive Force Apparatus Under an Electric Field

Sep 13, 2010

By Tuncel M. Yegulalp

The objective of this study was to categorize mining operations in the stone, and sand and gravel industries into areas of similar ground control functions and define initial factors affecting operational safety in each area, by means of utilizing publicly available data, telephone interviews and on site observations. The findings and recommendations presented in this report are based on the information collected during the two phases of the project. They also contain, in part, the collective qualitative opinion of the operators with respect to government rules and regulations on ground control safety and the implementation of these rules and regulations by government inspectors.

Jan 1, 1981

By Jim Lauder, Russ Calow, Ken Maley, Michael Ounpuu, Stuart T. Caverly

"Stuart T. Caverly, Section Head XRF Laboratory, Jim Lauder, Systems Engineer, Russ Stuart T. Caverly, Section Head XRF Laboratory, Jim Lauder, Systems Engineer, Russ Concession Street, Lakefield, Ontario KOL 2HOAbstractOn-stream X-ray analyzers have become an integral part of modem milling operations. The calibration of these instruments is not difficult but must be performed carefully and with consideration for the principles of X-ray spectrometry. A discussion of successful calibration procedures as well as examples of several common mistakes is presented.IntroductionOn-stream X-ray analyzers (OSA) have become an integral part of modem mineral dressing plants. Advances in instrumentation and computer software make the analysis of process streams fast, accurate and precise. Proper instrument calibration that respects the fundamentals of X-ray spectrometry is essential if the data generated are to be reliable. Often the importance of this task is underestimated and delegated to a person with inadequate XRF training. Successful OSA calibration is the result of careful, systematic procedures.On-stream analysis is perhaps the most important tool that has been provided for the concentrator metallurgist. Combined with powerful, low cost PC's and distributed control systems, real-time elemental analysis affords today's metallurgist many opportunities to troubleshoot and optimize his process.Before OSA, operators had to be very experienced if they were to achieve good results. Even with hourly grab samples, most changes in control approach would still be based on visual cues from the circuit and gut instinct. Real-time analyses have changed that completely.The last two decades have seen a persistent drive to reduce production costs. Operations utilizing OSA have been the most successful in this endeavor. Direct benefits from the application of OSA are fairly obvious. Operators are able to make incremental changes in operational parameters (e.g. reagent addition, pH, cell level), and immediately monitor the effects. Variations in the characteristics of the mill feed can be identified and addressed immediately. More progressive operations have linked analyses to control loops to adjust process setpoints ( e.g. reagent additions), and to change them automatically according to formulas based on previous experience."

Jan 1, 1996

By H. W. Brandt

A field test was designed to inject a specially formulated two compound epoxy resin into the roof rock ahead of a working face to cement fractures and formation interfaces at the Westmoreland Coal Co., Winding Gulf Div., Eccles No. 5 Mine, Eccles, West Virginia. Five 30 foot long X 2 inch diameter, hold were drilled at an angle of 15° above the plane of roof line front the face of a working entry. The epoxy resin compounds were pumped through a proportioning unit and mixed in-line before being discharged into the drill hole under treatment it injection pressures up to a maximum of 450 psig. When the coal face was advanced an anomalous failure of the roof rock occurred in the treated section. Further testing was suspended until the cause of the failure could he determined. The polymers were tested, under confined conditions, in 2 inch pipe columns. Extreme temperature and pressure (up to 2400 psig) rises were recorded as they cured, It was concluded that this pressure source fractured the rock and caused the roof failure. The entire program was terminated after it was determined that the heat rise and resultant high pressures could not he controlled chemically or mechanically.

Jan 1, 1978

By G. N. Schrauzer

Work has been carried out in the development and testing of carbon monoxide (CO) detection devices which use silica-gel impregnated with metal salts. If carbon monoxide is present, the ?detection gel? (the treated silica-gel) changes from a yellow to a blue-green or blue color. The detection gel "regenerates", i.e., returns to its original yellow color, within 4-24 hours after removal from air containing CO. The detection gel exhibits a threshold of CO response which can be adjusted over a wide range of CO concentrations, typically from 50-500 ppm in air. The preparation of detection gel using salts of palladium, molybdenum and copper is described. Also reported are the results of testing the detection gel&apos;s response to carbon monoxide under varying conditions of temperature and humidity and in the presence of some potentially interfering gases. Low levels of hydrogen sulfide (~ 5 ppm)1 nitrogen dioxide (< 7 ppm), and acetylene (> 200 ppm) were found to affect the detection gel. Temperature and humidity were also found to affect the detection gel&apos;s response. Increasing temperature shortens the gel?s response time while increasing the humidity delays the gel?s response and alters the threshold of the gel. A brief discussion of the further research and development necessary to stabilize the detection gel?s desirable characteristics is included. Descriptions of testing equipment and procedures are covered in detail.

Jan 1, 1978

The concentration of Mt. Morgan sulphide ore has always been attended by serious loss of gold. Until recently, with a simple selective flotation flowsheet, even the lowest grade of ore milled-about 2 dwt. per long ton-thislloss was 0&#183;9 dwt., whilst for average to high-grade ore, 3&#183;5 to 5 dwt., the figure was 1&#183;5 to 2&#183;0 dwt. Early in 1937 it was decided to equip the research laboratory for an investigation into the condition and location of the escaping gold and the physical and mineralogical barriers preventing its recovery.With the completion of: this equipment in July 1937, trial and error testing, which had been explored to exhaustion, was abandoned and a five months&apos; research programme mapped out and commenced. Based on the knowledge so gained, a flowsheet combining primary desliming, bulk flotation of the natural slime, selective flotation of the deslimed fraction, and cyanidation of the selective flotation tailing was drafted and tried with encouraging results in a 70-lb. per hour pilot plant. This flowsheet, modified to meet current circumstances, is being dove-tailed into the existing 1,500-ton sulphide ore concentrator, though the cyanidation treatment is actually carried out in the oxidized ore mill, to which the flotation tails are pumped.RESEARCH EQUIPMENT(1) Five tube elutriator (Fig. 1) t built in the company&apos;s workshop.

Jan 1, 1939

By Simon D. Handelsman

?Artisanalmining ?Application of human energy (e.g. pick & shovel) directly to produce minerals ?majority no technical skills and lack adequate working tools ?Small-scale mining ?Application of modern technology for limited scale mineral production Significance of ArtisanalMining ?15 million people in artisanaland small scale gold mining ?55 developing countries ?Use of mercury damages health of 100 million people

May 1, 2006

By A D. Campbell, G R. Power

The objective of the draw strategy in a caving mine is to maximise economic return by minimising waste dilution3 and maximising ore recovery4. The draw strategy must also include suitable controls for air blast and mud rush hazards and is highly constrained until continuous cave propagation has been achieved. This paper details a three-year project at the Ernest Henry Mine (EHM), which used cave flow simulation software to develop a draw strategy that increased the mine value by 32 per cent.Dilution and ore loss can be significant in sublevel cave (SLC) operations and result in poor recovery and considerable economic losses. To minimise dilution and ore loss, cellular automata software was used to simulate cave flow over the mine life. The optimisation project required mining footprints for various cut-off grades to be developed. Draw strategies for each mine footprint were then generated using a range of shut-off grades. Economic assessment of each scenario was then conducted to determine the mine footprint and corresponding draw strategy that generated the highest NPV (net present value). The iterative simulation process was improved by developing automated software functions in the flow modelling software to reduce time taken to generate and assess life-of-mine (LOM) draw strategy scenarios.In addition to improving the NPV of the mine, the optimisation project also enabled a decrease in the mine cut-off grade which increased the ore reserve and extended the mine life. Overall, an iterative process of mine planning, cave simulation, economic evaluation and geotechnical analysis was used to significantly increase the economic return of the SLC whilst ensuring caving risks were controlled to an acceptable level.CITATION:Campbell, A D and Power, G R, 2016. Increasing net present value by a third at an operating sublevel cave mine using draw strategy optimisation, in Proceedings Seventh International Conference and Exhibition on Mass Mining (MassMin 2016), pp 167–174 (The Australasian Institute of Mining and Metallurgy: Melbourne).

May 9, 2016

By Lewis Martin

Spokane Research Center personnel are currently conducting research on cable bolts to assess their material and support properties, to provide design criteria for roof control systems under various types of underground mining conditions, and to provide background data for computer models of cable bolt supports. Laboratory studies of cable bolts made of conventional steel cables with Garford bulbs and collars resulted in recommendations on characteristics such as embedment length, hole diameter, cable bolt diameter, and configuration of cables. A completed series of laboratory tests has determined the minimum embedment length of resin required for resin-grouted, cable bolt ground support.

Jan 1, 1996