Search Documents

By E. G. Davis

As a result of interest by the U.S. Department of Energy, the Bureau of Mines conducted studies on comminution of bituminous coal to the 2-um particle size range using the Bureau-developed turbomill. Both "plant grind" size (80 pct minus 75 um) and microsize (minus 10 um) coal can be produced in a single step with the Bureau's turbomill. In 15 min, minus 2.4-mm coal milled in water with steel shot was reduced tc 65 pct minus 75 m and 26 pct minus 2 m, with an energy requirement of 139 kW^h/mt coal. Plant-grind size coal milled in water, with Ottawa sand as the milling medium, was reduced to more than 45 pct minus 2 m in 15 min, at 175 kW?h/mt. Plant-grind coal milled with steel shot was reduced to 57 pct minus 2 um in 15 min, at 138 kW?h/mt. When diesel fuel was substituted for water, the milling of the coal was less effective and less energy efficient. Keeping the pulp dispersed was critical. Without an effective dispersant, the slurry became very viscous with increased milling time, resulting in higher energy requirements, low heat dissipation, and poor grinding efficiency.

Jan 1, 1987

By W. Robert Thompson

Hurricane Katrina caused significant damage to transportation structures on the Gulf coast in August, 2005, including the destruction of the US 90 Bridge over Biloxi Bay, Mississippi. Part of the successful design/build proposal for the replacement bridge included a comprehensive test pile program of indicator piles and load test piles in the geotechnical investigation program. A total of 22 indicator piles were installed on the project using the pile driving analyzer to monitor the pile behavior. Five load tests were performed: two axial Statnamic, two lateral Statnamic, and one static axial. The results of the test pile program established driving criteria for production piles that included end-of-drive blow counts and pile tip elevations with an appropriate allowance for setup. The program also confirmed that the planned installation equipment and techniques of GC Constructors, a joint venture of Massman Construction Co., Kiewit Southern Co., and Traylor Bros., Inc., would install the piles to the design tip elevations before production piles began. An extensive program of restrike measurements at a range of times after initial driving of the indicator piles provided a systematic documentation of pile setup in the soil profiles on the site. These resistance values were used to develop a dimensionless setup factor ?S? as the ratio of the restrike resistance to the end of drive resistance. This factor varied from 1.5 for piles penetrating clays and tipped in sand to 3.0 for piles bearing completely in clay and helped establish an end-of drive blow count that included an allowance for setup. The CAPWAP analyses of restrike data with setup and the load test data were used to confirm the design unit side shear and end bearing values developed from the borings and static capacity calculations and to select the design pile lengths.

Jan 1, 2009

By M. Nyoka

Consideration of the economic, environmental, and social impacts associated with the life-cycle of a technology is of increasing importance for decision-making in industry. It has been suggested that economic assessment of technology deployment projects requires the translation of associated environmental effects into monetary values. This paper introduces an approach for identifying and evaluating environmental damage in monetary terms. The approach groups the environmental impacts associated with a technology life-cycle system into four main criteria: air, water, land, and mined abiotic resources. The valuation of the impacts on the resources consists of an economic cost benefit analysis (CBA) procedure that comprises four steps: the compiling of an impact inventory, a monetary valuation of the inventory, discounting, and a risk/uncertainty analysis. The monetary valuation step for impacts on air resources is primarily based on published externality costs for Europe and the United States, which are adopted and converted to reflect the South African context. Local opportunity costs are utilized for the other resource criteria. The damage costs are transformed into South African Rand at 2005 prices. The paper demonstrates how the approach may be applied in the assessment of projects in the metallurgical industry. Shortcomings in the approach are identified. For example, not all of the aspects that are considered necessary to assess environmental performances comprehensively can be valued in monetary terms. Also, certain values, specifically those pertaining to opportunity costs, need to be determined on a case-by-case basis. Furthermore, the uncertainties associated with the indicators obtained may strongly influence the usability of the results of an environmental performance assessment, e.g. future damage costs will change with fluctuations in the markets. It is concluded that although such an approach has merit in increasing the understanding of the potential financial implications of a technology?s environmental performance, further research is required to improve the approach described if it is to be used further in the South African metallurgical industry. Damage cost estimates that are specific to South Africa need to be developed to reduce uncertainty, and the combination of both quantitative and qualitative approaches is recommended for comprehensive sustain-ability decision-making.

Jan 1, 2007

By Nicolas Denies, Gust Van Lysebetten, Bart Lameire, Jan Maertens, André Vervoort, Noël Huybrechts, Flor De Cock

"Abstract Originally developed for ground improvement works, the deep mixing method (DMM) has increasingly been applied in recent years for the realization of soil and water retaining structures and as alternative to traditional foundation solutions. From practice, there is a real need for practical guidelines dealing with the execution, the design and the control of such applications. With the aim of developing such guidelines, the BBRI ‘Soil Mix’ project was initiated in 2009. Within this research project, deep soil mix (DSM) material from 38 Belgian construction sites has been tested. In spite of the large advances in the mechanical characterization of the DSM material, one major issue remains the representativeness of the typical core samples in comparison with the real scale behavior of the soil mix elements. There is among others the question of the influence of the unmixed soft soil inclusions on this behavior and the issue of the scale effect which must be considered in the design. In order to investigate these questions, 8 large scale UCS tests and 17 large scale bending tests have been performed on excavated soil mix elements. The present paper discusses results of this experimental campaign, presents some research perspectives and highlights different aspects related to the design of soil mix elements for the realization of retaining wall or foundation solution.INTRODUCTIONSince several decennia, the deep mixing method (DMM) has been used to improve the strength and deformation characteristics of weak soils. In recent years, deep mixing has increasingly been applied – in Belgium and in other countries – for the realization of soil and water retaining structures and alternative foundation concepts. With regard to the execution of the DMM, one can refer to the European standard EN 14679 on deep mixing (2005) that was elaborated under the umbrella of CEN TC 288 “Execution of special geotechnical works”. However, from practice, it has been experienced that this execution standard does not provide enough pragmatic information and guidelines, in particular for the more recent applications of the deep mixing method (with retaining and bearing functions). The same need by the sector for guidance rules linked to design aspects in the context of Eurocode 7 was experienced as well. With the aim of developing such guidelines and in order to provide feedback to the European standardization platforms, the Belgian Building Research Institute (BBRI) has initiated the BBRI ‘Soil Mix’ project (2009-2013) in collaboration with the KU Leuven and the Belgian Association of Foundation Contractors (ABEF), the Belgian branch of the EFFC. Within this research project, deep soil mix (DSM) material from 38 Belgian construction sites, with various soil conditions and for different execution processes (CVR C-mix®, TSM and CSM), has been tested (Denies et al., 2012)."

Jan 1, 2014

By William H. Schiffbauer

One of the safety and health research programs of the former U.S. Bureau of Mines Pittsburgh Research Center was the evaluation of technology that will provide remote-controlled operation of mechanized equipment in underground room-and-pillar mining. The purpose of this effort was to enable workers to be located away from the hazardous and unhealthful coal extraction area (the face). As part of this program, advanced machine navigation and control technologies were developed for underground room-and-pillar and highwall coal mining that can be applied to commercially available mining equipment. These technologies use off-the-shelf components and a flexible control software architecture to minimize the effort required to adapt them to mining equipment. An accurate, reliable navigation system that can provide the mining machine's heading and location is a critical requirement for a remote-controlled mining system. After investigating several different types of navigation sensors, researchers selected the Honeywell Ring Laser Gyro Inertial Navigation System (INS) as showing the most promise. It was installed on a continuous mining machine at our Mining Equipment Test Facility. Extensive testing at an open pit (OP) site was also performed. This report describes the INS as it was employed on the mining machine in the laboratory, in the field, and OP tests, and provides the accuracy and performance results of the OP and highwalltests.

Jan 11, 1997

By I. L. Bell

The ironmasters of America had asked the Iron and Steel Institute to visit the USA. The Council decided it was not possible to accept, but Mr. Bell visited; this is an account of his trip. Topics covered include transport, charcoal, coal measures, coal, anthracite, bituminous coal, flux, magnetic iron ore, specular iron ore, limonite, red hematite, clay ironstone, black band ironstone, smelting works, blast furnaces of Pennsylvania, Lake Champlain furnaces, Lake Superior furnaces, Cleveland furnaces, Pittsburg furnaces, Missouri furnaces, and those of the southern states. He goes on to describe Catalan hearths, malleable iron works, Bessemer works, the Blair steel process, and labour.

Jan 12, 1875

The Tertiary gold deposits of the Hauraki area are predominantly epithermal vein types containing mineral assemblages of quartz, calcite, pyrite, sphalerite, galena, chalcopyrite, acanthite and native gold (electrum). Sulphosalt, telluride (eg hessite), seleniferous sulphide and selenide minerals are important locally. Studies of wall rock alteration mineralogy, fluid inclusions in gangue minerals, and sulphur isotopes of sulphide minerals indicate that the ore forming fluids had the following parameters: pH, near neutral at depth but acidic near surface; temperature, predominantly 320 - 270¦C for base metal dominated assemblages, 280 - 200¦C for precious metal dominated assemblages and generally below 200¦C for late stage barite; apparent salinity, six to zero equivalent weight per cent NaCl; and CO2 concentration, generally around one mole per cent CO2. There is fluid inclusion evidence for boiling during mineralisation in some deposits. Moderate values off S2 and FO2 are indicated for base metal and mixed base metal û precious metal assemblages of most deposits by the predominance of pyrite + chalcopyrite over other iron-bearing phases; primary bornite is absent, whereas pyrrhotite, hematite and magnetite rarely occur in the veins. The largest gold û silver deposits formed from solutions in which the sulphur species in solution were predominantly reduced. Near surface environments and some deep, predominantly base metal, deposits were formed from solutions with approximately equal concentrations of oxidised and reduced sulphur species.

Jan 1, 1984

The 106th Annual General Meeting of The South African Institute of Mining and Metallurgy was held in the J.C. Lemmer Auditorium, SA National Museum of Military History, 22 Erlswold Way, Saxonwold, Johannesburg on Wednesday, 13th August, 2003. Welcome The President extended a special welcome to the guests and representatives of our sister institutes and other associations, also to recipients of awards, senior members of industry, Honorary Life Fellows, Past-presidents, our Members and other guests, among them the following: Kevin Moxham, President, Association of Mine Resident Engineers Prof. Jay Barton, Vice President, The Geological Society of South Africa Dr Gus Muller, President, Institute of Certificated Mechanical and Electrical Engineers, South Africa Marius van Rooyen, President, Institute of Mine Surveyors of South Africa Benjamin Ngulube, Deputy Vice President, South African Institution of Electrical Engineers Dr Francois Malan, Chairman, South African Institute of Rock Engineering Dr Paul Jourdan, President, Mintek

Jan 1, 2003

By Srinivasulu Tadisetty

The productivity and safety of Indian longwall operations are insignificant because of complex geomechanical conditions. Therefore, the continuous monitoring and forecasting of abnormalities is imperative. Authors developed an innovative real time system and implemented in one of the Indian longwall mines. The real time system was successfully acquired data from underground chock shields and classified the behaviour in real time as per the standard norms. Furthermore, it forecasted the abnormal behaviour of chock shields promptly. The management was implemented appropriate precautionary measures based on real time forecast. Subsequently, the longwall operations were successfully completed with enhanced productivity and safety. This paper discuss the impact of the innovative system on productivity of experimental longwall mine.

Jan 1, 2006

By Donald E. Ralston

The Huntsville study area in northeastern Alabama consists of Jackson, Limestone, Madison, and Marshall Counties. Major emphasis was placed on the Huntsville urban area in Madison County to analyze the relationship of urban growth and the minerals industry. Huntsville was delineated into its component urban, suburban, and rural parts for 1964, and the primary area of growth was predicted for 1990. Population estimates were made for the four-county area as a unit and Madison County separately, and projected to 1990. Demand estimates for crushed stone and sand and gravel were made for the same area units and projected to 1990. Analysis of quarry sites in the Huntsville area was made for the present and for the future. The mineral operations of the study area are all located in rural areas; in the case of Huntsville, the mineral sites are located in areas defined as "rural" in the component urban-suburban-rural system. The operations outside Madison County can expect to have minor problems with urban encroachment, while those operations in Madison County can expect major problems associated with urban growth and development. Some of the problems associated with limes tone production can be reduced if producers invest in capital equipment that will reduce the nuisances inherent in this activity. Although urban expansion endangers some quarry operations in Huntsville, topographic and political restrictions which prevent urban expansion can effectively shield quarry operations for some time.

Jan 1, 1970

By R. L. Brown

This report, summarizing the Bureau of Mines research and technologic work on coal and coal products for the period July 1, 1950, to July 1, 1951, is based largely on publications issued during the year. The sixteenth in an annual series, it gives footnote references to publications giving further details of the research and technologic work described, except in a few cases where research data presented herein has not been published previously. During the year, the national fuels situation was generally one of plentiful supply.3/ Mineral-fuel resources appeared adequate for several hundred years at reasonably increasing rates of supply. Coal-production capacity was in excess of demand; petroleum supplies were adequate; and natural gas use was limited only by pipeline capacity. However, it was pointed out that a world war would drastically change this situation of relative plenty, particularly with regard to supplies of petroleum and its products. Conversion to the use of coal on a large scale would be required, and improved methods of mining and of processing and using coal in solid or fluidized form or converted to liquid fuels could materially contribute to our national safety.

Jan 1, 1952

By L. Nahai

Iran's petroleum industry is nearly 50 years old and the oldest in the Near East. According to published figures, Iran ranks third in production and reserves in the Near East. These reserves (including probable reserves) are estimated at 35 billion barrels and constitute about 11 percent of the world's total. Iran is the sixth largest producer of crude petroleum in the world. The 1961 output of more than 430 million barrels was 5 percent of total world out-put for the year. In the same year, Iran ranked fourth among world petroleum exporters, providing 8.4 percent of total world exports.

Jan 1, 1963

Council for 1999/2000 President M.H. Rogers President Elect Dr L.A. Cramer Vice Presidents Senior A.A.B. Douglas Junior S.J. Ramokgopa Immediate Past President J.R. Dixon Honorary Treasurer J.A. Cruise [ ] Annual report In accordance with the current management policy, this report on the activities of the Institute is presented under eight main headings: 1. Interests of Individual Members 2. Technical Meetings 3. Publications 4. Regional Development 5. Engineering Science and Technology in South Africa 6. International Liaison 7. State Liaison 8. Management and Administration.

Jan 1, 2001

By R. H. O. Wagner

"This paper describes the bench testing, pilot plant studies of alternative flowsheets, to determine the feasibility of gold recovery, by carbon in pulp extraction, in the Schumacher Mill gold flotation tailings. The economics were calculated based on pilot plant recoveries and actual industry operating costs.The economics of the carbon in pulp treatment of the gold flotation tailings were not justifiable. The economics of desliming the gold flotation tailings followed by carbon in pulp treatment were marginal, but favourable. INTRODUCTIONPamour Porcupine Mines, Limited is a gold, silver and copper producer located in Timmins, Ontario. In 1983 the head grade of Pamour's gold ores averaged nine one hundredths of a troy ounce of gold per short ton.Pamour operates two area mills to concentrate the gold ores. Free milling gold ores are processed at the Pamour One Mine mill, whereas the refractory carbonaceous gold ores, and complex gold, silver, and copper sulphide ores, are processed through the Schumacher Mine mill.The complex Schumacher mill feed ores do not all react favourably to flotation methods, consequently this study was commissioned to investigate the feasibility of the carbon in pulp cyanidation of the Schumacher mill gold flotation tailings. These tailings contain ten to fifteen percent of the gold in the mill feed. During the study period, the average grade of the Schumacher mill flotation tailings was nine one thousandths of a troy ounce of gold per ton, or one quarter of a gram of gold per metric tonne."

Jan 1, 1984

Acid soluble calcium is depleted in drainage sediments from hydrothermal alteration centres in the Coromandel Peninsula. The routine analysis of acid-soluble calcium on drainage samples is an economical and effective technique for outlining hydrothermal alteration centres in volcanic terrains.

Jan 1, 1979

By M. E. Steidlitz

FABRICATION of semiconductor devices.requires the formation of electrical contacts, often involving the use of lead, tin, and lead-tin solders. In several recent instances when germanium had been bonded to nickel with lead, a new metallic phase appeared, unattached to either germanium or nickel, but rather suspended as a continuous foil wholly contained within the lead matrix. Since such metallic structures do not form in nickel-lead or lead-germanium systems under identical conditions, a brief study was made of the characteristics and possible formation mechanisms of this material. EXPERIMENTAL Specimens were prepared by placing single crystal, transistor-grade germanium discs, 30-mils in diam by 6-mils thick, into a depression in a graphite boat. =A* nickel washers, 125 mils in diam by 5-mils thick, containing a center hole of 10-mils diam, and coined into a soup bowl shape, were loaded on top of the discs, so that the bottom of the

Jan 1, 1959

By A. Burger Pintér

To be meaningful the sharing of ideas about the National Environmental Management Act (NEMA) and social issues within the context of Mining and Metallurgy (M&M) requires an honest scrutiny of the M&M/social environment relationship, both past and present. It is not a secret that this relationship has been and is fraught with difficulties. Thus from all perspectives (M&M, society and environmental and social consultants) such a dissection, that highlights the realities, both good and bad, is uncomfortable. For this section of the colloquium to have any value, the honest but difficult approach needs to be taken.

Jan 1, 2000

By Norman A. Jull

"Factors which affect the separation achieved in a hydrocyclone are discussed and illustrated with graphs of some mathematical relationships.Definitions of separation and sharpness include comment on use of elutriation devices.A plea is made for better evaluation of field data prior to their reporting or use in calculations. Methods of evaluation are suggested, with samples of the relevant calculations.An example of the effect of percent solids errors is given, with computer printout and plotted corrected recoveries.INTRODUCTIONThe range of interest in cyclones runs from a simple demand for classification results to a detailed study of published equations defining cyclone characteristics. Probably this group covers as broad a range and, in an attempt to offer something for everyone, I will begin with general operating comments, then move on to more analytical topics. Ideally, an author would compose his paper after the discussion period, when he would have a better idea of the areas of special interest to his audience.Sor'1e of you may share our incurable fascination with classification, especially as performed in cyclones. It is amazing that such a simple device could be in use for more than 20 years and retain as much mystery as it does. Substantial parts of the mystery have been solved but some remains, to keep up our curiosity. There is at least one valid reason: the unusual compactness of this device, which makes internal observation very difficult. What other unit can you think of which performs such a complex separation between particle sizes, shapes and specific gravities at such high capacity? Retention time in a cyclone is typically 3 seconds!Mutual Agreement - In a cyclone, every parameter of geometry and of operation interacts with every other. In an orderly discussion of individual parameters it would be necessary to repeat, in every section, 11 if all other factors are equal"". Could we agree now, for our mutual convenience, that that phrase is clearly understood between us during the remainder of this paper?"

Jan 1, 1972

Innovative Technology for Optimised Thickening Sedimentation

Sep 13, 2010

By B Nielsen, H Lehto, J Rohleder, C Robben

Sensor-based ore sorting is being increasingly used to reduce the amount of low-grade and waste material processed in mineral concentrators. This type of preconcentration provides bottom-line benefits to users by reducing the amount of energy, water and consumables, as well as reducing capital cost. Existing operations can increase metal production, while previously uneconomic deposits and low-grade stockpiles can also be exploited. The technology can also be used to separate ore types for selective processing. The path to implementing sensor-based sorting may include:• geometallurgical evaluation• first inspection testing to investigate sensor response• bench-scale testing where sensor selection is not obvious or for difficult applications• performance testing in full scale sensor-based sorting machines• larger scale site-based piloting with a temporary semi-mobile plant installation. Sorting requires material to be suitably prepared and presented to the machines and typically this consists of crushing and screening to limit top size and optimise liberation. However, where material streams are suitably sized and prepared, additional equipment may not be required (e.g. the sorting of semi-autogenous grinding (SAG) Mill pebble streams).This paper presents a case study of economic upgrading of gold ore, by preconcentrating with sensor-based ore sorting. The case study examines sorting amenability, test work, the feasibility study through to implementation, with associated flow sheet development. The development process is analysed and evaluated with a view to rationalising the process for development of future projects. In addition, limited financial modelling based on expected results is shown to illustrate the benefit to the operation.CITATION:Nielsen, B, Rohleder, J, Lehto, H and Robben, C, 2017. Sensor-based ore sorting to maximise profit in a gold operation, in Proceedings MetPlant 2017, pp 131–146 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 11, 2017