Search Documents

SEVERAL serious accidents, which had occurred owing to the platman leaving the plat without first withdrawing the "chairs" from the shaft, set the writer scheming to devise a mechanically operated system which would obviate such accidents and be "fool-proof". It was obvious at the outset that some means of indicating to the engine-driver by the movement of the "chairs" themselves, whether they were "in" or "out" of the shaft, was necessary.An arrangement of signalling similar to railway semaphores was considered, but was rejected owing to the difficulties accruing from the large number of communicating wires which would be required down the shaft-viz., 2 for each level. After several experiments, a comparatively simple and efficient electrical system was devised, and which is covered by Commonwealth Patent TO. 10,402.One of the chief features of the apparatus is its simplicity, and its strongest point is the fact that both the engine-driver and platman receive visual indication of the position of the "chairs." The arrangement consists of a miniature coloured glow lamp, one for each level of each shaft compartment, arranged and placed beside the numbers and arrows corresponding to the various levels, on the winding engine indicators. Also a large indicating glow lamp is installed at each compartment in the various levels, in proximity to the levers for operating the "chairs." Upon operating the various levers for the "chairs," an electrical current...

Jan 1, 1909

To predict the spontaneous combustion potential of bituminous coals using a simple expression based on an easily acquired coal property. Background Approximately 20% of underground coal mine fires in the United States since 1978 have been attributed to spontaneous combustion. Spontaneous combustion fires in underground mines are most likely to occur in gob area; and are difficult to detect and to extinguish by direct fire fighting methods. Often, sections of the mine or the entire mine must be sealed for long periods, at a great economic loss to the mine operator, mine employees, and the surrounding community. It is conservatively estimated that the cost of scaling a large mine is about $50 million.

Jan 1, 1989

By Gregory M. Molinda

The Coal Mine Roof Rating (CMRR) was developed 10 years ago to fill the gap between geologic characterization and engineering design. It combines many years of geologic studies in underground coal mines with world-wide experience with rock mass classification systems. Like other classification systems, the CMRR begins with the premise that the structural competence of mine roof rock is determined mainly by the discontinuities that weaken the rock fabric. However, the CMRR is specifically designed for bedded coal measure rock. Since its introduction, the CMRR has been incorporated into many aspects of mine planning, including longwall pillar design, roof support selection, feasibility studies, extended-cut evaluation, and others. It has also become truly inter-national, with involvement in mine designs and funded research projects in South Africa, Canada, and Australia. This paper discusses the sources used in developing the CMRR, describes the CMRR data collection and calculation procedures, and briefly presents a number of practical mining applications in which the CMRR has played a prominent role.

Jan 5, 2007

Stope support systems, typically consisting of props and packs, are used extensively in the gold and platinum mining industry to stabilize the rock mass in the excavation vicinity and to reduce the hazard associated with rockfalls and rockbursts. The design of stope support systems was historically based predominantly on past experience and practices, and cost considerations. The recent development of a new and improved support design methodology, has led to the potential for significant increases in worker safety and support cost savings. This paper reviews some of the fundamental rock mass and support criteria that form the basis of the improved support design methodology. The considered design criteria are the height of potential fall; quasi-static stope closure rates; dynamic stope closure rates; compressive hangingwall stresses; discontinuity spacing, orientation and interface properties; effect of support length (stoping width); effect of compression rate; consistency of support performance; a real coverage; support spacing; and zone of support influence. The proposed support design methodology combines both the zone of influence and key block stability theories, resulting in optimized support systems for rockfall and rockburst conditions. The site-specific methodology consists of two stages: (i) a tributary area analysis, and (ii) a zone of support influence and a stability analysis, considering hangingwall failure due to buckling, shear and block rotation, which gives maximum safe spacing of individual support units. The methodology is suitable for designing support systems for both blocky hangingwalls and hangingwalls fragmented by face-parallel extension and shear fractures.

Jan 1, 2001

By Edna A. Dancy, Gerhard J. Derge

Jan 1, 1963

Roof falls in coal mines typically occur in or around intersections and this has not changed in the last two decades. This research develops an improved scientific understanding of stress distribution and associated failure behavior around 4-way and 3-way coal mine intersections. Three-dimensional numerical analyses were performed to determine factors that influence intersection stability. The analyses used Hoek-Brown failure criterion. Failure zones around 3-way and 4-way intersections were developed. Intersection span and horizontal stress have a major influence on intersection stability. For the 4-way intersection, pillar corners across the intersection fail first and lead to progressive failure of immediate roof and floor layers. The mechanism of failure is similar for the 3-way entry but the shape and extension of failed zones differ. Coal ribs mostly fail due to tensile stress, while roof and floor strata fail due to shear stresses. Rib corners fail due to a combination of shear and tensile stresses. In addition to stress distribution; safety factor contours analysis was performed to assess stability of intersections.

Feb 27, 2013

By D van der Merwe

Tracers of known densities are used world wide in coal processing plants to evaluate plant performance. Tracers are added to the feed stream and are counted after being recovered from the product and discard streams to determine partition curves. The need to recover the tracers can be eliminated by adding radio frequency identification tags to the tracers. Readers mounted on the product and discard streams record the passing RF tracers and produce the partition curve instantly. Tests were performed with three different shaped tracers at different collieries on cyclones ranging from 510mm to 800mm in diameter. Sink and float analyses of coal samples were used to compare conventional partition curves to partition curves obtained by using RF tracers. The average amount of tracers recorded was 78% of tracers in the feed. The results indicate that the stone shaped tracers represent the results from the sink-float analyses the best. The results suggest that RF tracers can be used to evaluate cyclone circuits in the coal industry and will make it possible to evaluate a coal circuit?s efficiency without stopping a plant and waiting for laboratory analyses. Keywords Coal tracers, partition curve, radio frequency tracer, RFID

Jan 1, 2006

By Paul Staples, Fred Woodcock, Robert Grant, Mike Cooper

"Noranda's Brunswick Mining Division, near Bathurst, New Brunswick, processes 10,500 TPD of complex Cu-Pb-Zn bearing ore. Brunswick uses conventional rod and ball milling techniques to achieve a flotation feed size of 75% passing 400 mesh. Over a two year period, testwork was performed using a Marcy pilot plant ball mill to assess the impact of several key variables on secondary grinding efficiency. Four graded mill charges were used to compare balls and slugs at 25 and 29 mm sizes. Data was evaluated by determining grinding rates using a commercially available steady state simulator. Results were critical in Brunswick's efforts to achieve finer grinds while minimizing cost per tonne.IntroductionBackgroundThe Brunswick orebody is an extremely fined grained volcanogenic massive lead, zinc, copper, silver, iron sulphide body between two metamorphosed sedimentary and felsic volcanic rock units. Pyrite content is about 60% with 20% non-sulphide minerals, mainly silica and chlorite.Size reduction at Brunswick is performed by three separate parallel lines consisting of rod mills, primary and secondary ball mill circuits, all in series. The line 3 grinding circuit is presented in Figure 1."

Jan 1, 1997

By Paul J. Axtell

Two new railroad bridges in Kansas City, Missouri are founded on drilled shafts embedded into the soil and underlying shale. The uncertainty arising from the non-homogeneous, anisotropic nature of most shales, and the variability of shales across the U.S., makes it a difficult material to assign appropriate design properties. As was the case on this project, the uncertainty of foundation performance in shale can lead to overly conservative designs, particularly with drilled shaft foundations. An extensive Statnamic axial testing program was performed to verify that the load-settlement behavior of the drilled shafts would be acceptable for the intended railroad traffic. Axial Statnamic testing was applied in three increasing cycles of 927 kips, 1007 kips, and 3177 kips, respectively. The maximum movements recorded at the shaft head during each of the loadings were 0.052 inches, 0.062 inches, and 0.257 inches, respectively. The loads applied in each of the respective Statnamic tests were not sufficient to reach the capacity of the shaft; so direct comparison of measured and calculated capacities is not possible. However, evaluation of the estimated design capacity can be accomplished based on results from the Statnamic testing program by utilizing normalized load transfer relations presented by O?Neill and Reese (1999). Such comparisons necessarily require extrapolation of the data measured in the Statnamic tests following typical load-displacement response. Results indicate the Kulhawy and Phoon (1993) method for estimating side resistance in Pleasanton shale rock sockets, assuming a smooth socket, appears to agree well with observed behavior during Statnamic testing. Accordingly, the O?Neill and Reese (1999) method for estimating the toe resistance in intermediate geomaterials, assuming cohesive rock with Rock Quality Designation (RQD) between 70 and 100, appears to agree well with observed behavior during Statnamic testing. Finally, based on Statnamic testing at varying load magnitudes and normalized curves developed by O?Neill and Reese (1999), the contribution of side resistance to the capacity of a deep foundation can be determined assuming no load is transferred to the base of the foundation during lower magnitude testing. Furthermore, higher magnitude testing can provide a means to evaluate the accuracy of design end bearing calculations.

Jan 1, 2006

By Osamu Taki

This paper presents the system, the strength of column, the design concept, and the applications with four case histories from the past project as the general aspect of Geo-Column (trade mark of single soil-cement column by SCC Technology, Inc.). In the system, it shows the installation process and drilling/mixing tool with the mixing process. In the design concept, it shows how to design Geo-Column against the vertical and horizontal load. Finally, it shows the applications with four case histories, (1) building mat foundation, (2) isolated foundation on the pedestrian bridge, (3) bridge spread footing and slope erosion control wall in the channel, and (4) cut-off wall and shoring wall in the underpass roadway to the railroad.

Jan 1, 2000

By Bernard Lewis

During the past 10 years the technical investigations conducted by the Explosives Division of the Mine and Explosives Bureau of the Bureau of Mines have been described in a series of summarizing reports prepared by Wilbur I. Huff, consulting explosives chemist of the Bureau. These reports covered the…

Dec 1, 1947

By Luke Erickson

San Francisco Public Utilities Commission is planning to replace 5 miles of pipeline under San Francisco Bay. The tunnel will be constructed using an Earth Pressure Balance (EPB) TBM and will be the first TBM-driven tunnel under the Bay. The alignment passes under environmentally sensitive habitats, through interbedded layers of sands and clays, and through a buried bedrock ridge. This paper discusses the geotechnical characterization and anticipated tunneling conditions and presents the analysis of various construction methods that resulted in the selection of an EPB TBM. Considerations related to tunneling with an EPB TBM are described in detail, including ground conditioners, TBM cutterhead wear, muck control, and squeezing ground.

Jan 1, 2008

By T D. Sullivan

Risk lies at the heart of all mining and nowhere more so than in pit slope design. Mining is principally about two areas of risk; safety and economics. This paper addresses the main elements of pit slope design and presents a view of the state of the art in terms of safety, design, prediction of performance, success and pit slope management. There has been a recent trend for serious injury and fatalities due to stability in open pit mines. The causes and contributing factors are analysed in relation to geotechnical knowledge, pit slope design and management. Currently there is no standard classification system for mine slope designs and it is considered doubtful if a universal system is possible. Designs are usually formulated in accordance with many different methodologies, various engineering principals and a number of different philosophical approaches, with results often presented in terms of Factors of Safety or Probabilities of Failure. However wide experience has demonstrated that even with apparently detailed engineering investigation and analysis at Feasibility Level, at the Operating Stage mine slope angles are regularly subject to large changes. The general experience is that these changes are ± 5° and 16° overall, which is considerably outside the accepted order of accuracy. For large deep mines these are huge changes and represent significant risks to the operations. The current state of practice in pit slope design is examined for two stages, feasibility and operating.

Jan 1, 2006

By Robert A. Cummings

A rock mass classification system has been developed for support estimation in mines using caving methods. The developed system (MBR System) accepts readily-obtainable geotechnical properties, and mining geometry, to develop a rating that permits recommendations for drift support in block caving mines. The data base includes major active United States caving mines. The method is intended to be used for planning and estimating purposes and for preliminary support design. The Manual explains the organization and nature of the MBR System, its derivations, details of required input data, methods for assessing the data and for developing rock mass ratings, and techniques for selecting the most appropriate mine support recognizing mine requirements and desired stability. A worked example is provided.

Jan 1, 1984

By A. M. Ramalho

In the synthesis and sintering processes to obtain superhard materials, such as diamond and cubic boron nitride, deformable ceramic capsule is used as gasket to transmit and support the required high pressures and high temperatures, HPHT. The ceramics materials for these capsules should have special physics and chemical characteristics such as refractoriness, shear strength and compressibility. In this work, Bridgman?s anvil made of hard metal or speed steel was used to characterize some ceramics materials in terms of their maximum compressible thickness. Tests were also performed with different resin polymers used as binding mixture with ceramics powder. Chemical analyses and investigations through scanning electronic microscopic (SEM), X-ray and real tests for the synthesis of diamond were also performed. The results showed that local Brazilian calcite can be successfully used in the manufacture of HPHT gaskets.

Jan 1, 2006

By F. Z. Utyashev

The present work considers the essence of fragmentation: on the level of a simple model as a material response to the curvature accumulated by it at large deformations. It is on this basis that the correlation between curvature and fragment sizes is determined. It is shown that at deformation the area of curvature center inevitably changes. It is revealed that a specific value of variation of center surface area, i.e. ^As parameter, is numerically equal to the value of curvature acquired by a material. Minimum sizes of fragments and grains depending on ^As have been estimated, and the dependence of this parameter on strain has been established. Besides, the present paper considers the effects exerted by curvature center geometry, material distortion, directions of deformation and thermal warming up in the localization zones on structure refinement when various techniques are applied.

Jan 1, 2006

By J. Daavittila, P. Jokinen, M. Honkaniemi

In the latter part of the 1980?s Outokumpu Chrome in Tornio, Finland, was in a situation when its twenty-year-old ferrochrome plant was becoming inefficient to sustain economically sound production. The company made extensive studies on the then available processing methods to find out the best possible processing route. As a result the whole plant was practically rebuilt and expanded. When equipment was proven in practical operation an application for FeMn production was developed. Now when Tornio FeCr-plant is considering the expansion the same type of exercise is to be performed with today?s challenges, which will be discussed in the paper. These challenges include increasing costs or decreasing quality of raw materials, increasing energy costs, stricter environmental regulations and demand of better working conditions. The possibilities to respond to these challenges will be discussed in the paper. The future and continuing development with FeCr includes the better utilization of process dusts and a lower consumption of energy. By adapting the latest automation tools to better control of the process even higher efficiencies can be achieved with present technology. New processes are considered for development in the future and some possible technologies will be described.

Jan 1, 2004

By Richard A. Bideaux

With both unit costs per meter and average depth of drilling constantly increasing, there is a strong incentive to maximize the information acquired from drill holes, and then to make this information accessible to the geological staff. The larger the drilling project, the more advantageous computerization of data is over manual methods. The conversion to computer-readable form and the verification of large amounts of drill-hole data can be a substantial data processing task, but once accomplished, the benefits in increased accuracy and speed of interpretation will compensate for the time and effort spent in the work. For an exploration project progressing towards a preliminary feasibility study, about half of both the time and costs for all computer work of the entire feasibility study are devoted to drill-hole data base organization, and maintenance. Once drill-hole results are quantified and verified to be correct, they are immediately accessible and are not subject to further transcription or reinterpretation of errors. To obtain maximum benefits from computer utilization in this area, the drill-hole data base should be set up along with availability of the first data. For some companies, this may initially comprise a large number of purely speculative drill holes on a spacing of perhaps 1 or 2 km. Although few of these drill holes may encounter economic material, thought should be given, at this time, to the variables which will be logged when such material is found. In this way, it should be possible to set up a consistent format into which all future drill-hole information will readily be accommodated. This format may even be carried over into the data base requirements for an operating property.

Jan 1, 1979

By L Besra, A. R. Prasad, B. P. Singh

The role of surface-chemical phenomena and the physical processes that participate in the dewatering of a suspension of alumina trihydrate were subjected to a systematic investigation, which has increased understanding of the influence of surface tension, contact angle and adsorption in the process. The residual moisture content of the cake can be reduced significantly through the use of surface-active agents in slurry pretreatment or as wash-water additives. The effectiveness of a particular surfactant is hard to predict from any single parameter, but is dependent on its ability to reduce surface tension and possibly to modify the solid-liquid contact angle. If scaled up to industrial operation of the dewatering step of the Bayer process in India, the use of these chemical additives could substantially improve its process economics, reducing the fuel costs for thermal drying by a much as Rs 50/t

Jun 21, 1905

By N. I. Aziz

The importance of using disc cutters for rock excavation is reflected by their wide application in hard rock cutting machines such as tunnel boring machines and raise borers. The forces involved in the cutting process are those due mainly to thrust and rolling forces and are greater than that required by cutting picks. An interesting feature of cutting with discs is the formation of surface crushing, surface and sub-surface chipping and primary crack formation. Experimental, as well as analytical, work has been carried out to determine the optimum spacing between the disc cutters to control primary crack orientation. Wedge bit indenters were used to simulate disc cutters. The paper concludes by proposing a new approach to rock excavation by hybrid cutting based on controlling the primary crack orientation.

Jan 1, 1992