Search Documents

By Oliver Bowles

Sandstone, a widely distributed siliceous sedimentary rock, is the third most popular building stone in the United States. It is formed by the breaking down of preexisting rocks by weathering, subsequent segregation of the detrital quartz grains into discrete deposits by the sorting action of water or wind, and finally cementation of the quartz sand into a coherent rock. The homogeneity and resistance to weathering of the resultant sandstone make it suitable for exterior construction. Its excellent wearing properties explain its popularity for flagging and stair treads. However, quarrying and dressing methods and costs are adversely affected by the abrasiveness and hardness of sandstone especially as compared to limestone.

Jan 1, 1963

By T. Lux, M. Hanel, Degel, A. Filzwieser, R., H. Joubert

It is the increasing demand for an economic and cost saving operation mode that requires effective cooling in order to achieve low refractory wear and good furnace lifetime, which is making cooling technology an important aspect of furnace operation. In addition, the requirements for safety are getting more and more into focus. However, the use of water—today’s standard cooling medium—has major drawbacks as it can cause problems both during furnace start up and operation, namely hydration problems, corrosion, and explosion. Not to forget the severe risks for the operators as well as economical damage in case of a malfunctioning water cooling system. With this new and patented cooling technology ILTEC and the ionic liquid IL-B2001 as the cooling medium, it is possible to realise a water-free cooling solution and therefore the door is wide open to rethink existing and conventional cooling solutions. Furthermore, there is also the chance to recover heat from the process in a more efficient way. However, since the technology is novel and unique there are a lot of concerns and doubts regarding safety for plant operators and employees. The paper is intended to cover both: highlighting the enormous potential of the technology but also to eliminate concerns mainly caused by rumour and unawareness. INTRODUCTION All of us are aware of the risks when water is used as a coolant and placed in the vicinity of the liquid metal phase. Unsuitable design solutions or wrong operation modes of the furnaces or failures of refractories can cause a direct contact of water with liquid metal. The consequences can lead to equipment failures, vessel destruction but even worse to injuries and even fatalities. Over the past decades, countless incidences were reported. Fatal accidents caused by water coming into contact with liquid metal happen every year (Oterdoom, 2014; Filzwieser, Konetschnik, Filzwieser, Wallnerm & Preiss, 2014). With the novel ionic liquid cooling technology virtually all negative effects of a water cooled system regarding safety are eliminated and even additional benefits can be provided (Voermann, Ham, Merry, Veenstra, & Hutchinson, 1999;Verscheure, Kyllo, Filzwieser, Blanpain & Wollants 2006; Wallner, Filzwieser & Kleicker 2006). The fact that no explosion occurs when IL-B2001 gets in contact with molten metal results in a revolutionary solution for the metallurgical industry in terms of safety—new safety standards can be achieved.

Jan 1, 2019

By S. J. Aresco

The Bureau of Mines has been active in promoting the purchase of coal for Government use under specifications that define the requirements in terms of heating value of the coal, expressed in British thermal units, and the composition as shown by proximate analyses. To these, when required, are added the ash-softening temperature, the free-swelling index, and the Hardgrove grindability index. Under most of these specification contracts the bidders guarantee the quality of the coal, and that guaranteed by the successful bidder becomes the standard of his contract. The deliveries are sampled in accordance with instructions4/ issued by the Bureau of Mines, the samples are analyzed in the Bureau laboratory to determine whether the coal is of the quality guaranteed by the contractor and, if it is not, a price adjustment is made. Analyses of the delivered coal and tipple samples (samples collected at mine tipples as coal is being loaded into railroad cars or trucks) provide valuable data for use in evaluating future bids. In addition, the continuous sampling of coal as delivered is a check on the practical results obtained in burning the coal.

Jan 1, 1957

Declining metal prices over the last few years have reduced the number of new metallurgical plants being built and limited opportunities for introducing new processes. However, technological advances are still being made. With increasing economic pressures, the emphasis is now on reducing unit costs by making equipment larger and through use of technologies with lower operating costs. This trend can be seen in the increasing size of grinding mills and flotation cells used in recent plant designs and in the adoption of HPGR crushing as an alternative to SAG milling. Few new technologies achieve widespread introduction until there are clear economic or operational drivers. These might currently include: ò          increasingly stringent environmental standards; ò          availability of exotic materials for equipment construction; ò          increasingly sophisticated instrumentation and control systems; ò          the need to treat increasingly refractory oretypes; and ò          the length of supply routes to many new plants. As a result of these drivers, a number of new and revitalised technologies will get increasing prominence in the design of new operations, such as: ò          use of ultrafine milling equipment such as MIM's Isamill for treatment of refractory gold ore concentrates; ò          use of thiourea as an alternative for cyanide in sensitive locations; ò          novel hydrometallurgical routes for treating base metal ores in remote locations; ò          paste thickening for tailings deposition; and intensive cyanidation of gravity concentrate

Jan 1, 2000

By G. Bulut

The recovery of copper and cobalt from ancient copper slags from the Küre region of Turkey was investigated. A fayalitic-type of ancient copper slag containing 1.24% Cu, 0.53% Co and 53.16% Fe were subjected to an experimental study. Two different routes were followed to recover the metal values. The first route was roasting the slag with pyrite followed by leaching. The second route was flotation of the slags, roasting of the flotation tailings with pyrite and leaching. The second route was found to be suitable for the treatment of the copper slag studied. In the flotation step, a copper concentrate containing approximately 11% Cu was produced with a 77% recovery while 93% of the cobalt stayed in the tailings. In the roasting experiments, the effects of roasting time, pyrite: slag ratio and roasting temperature on the dissolution efficiencies of Cu and Co were investigated, and the optimum conditions were determined. In the tests, 87% of the cobalt dissolution was observed after one hour of roasting at 500°C with a pyrite: slag ratio of 3:1. The copper dissolution in the tests was 31%. Based on the results of this study, a process flowsheet is proposed for the evaluation of these slags.

Jan 1, 2007

This Bureau of Mines report reviews the information presented at the Sixth Mineral Waste Utilization Symposium cosponsored by the Bureau of Mines, U.S. Department of the Interior, and the IIT Research Institute. Environmental scientists and engineers from nine countries participated in the symposium, which was held May 2-3, 1978, at the Chicago campus of IIT Research Institute. The 56 papers presented on the reclamation and recycling of mining and mineral wastes, municipal solid waste, industrial wastes, and scrap metal are summarized herein.

Jan 1, 1980

By J. F. Curtis

In the synopsis, the author concludes that ?high levels of seismicity do not coincide with high rockburst rates?. Implicit to an appreciation of this statement is the necessity of a common understanding of what is understood by the terms: ?high level of seismicity? and ?high rockburst rates?. With respect to the former term there is no difficulty in that the level of seismicity is traditionally measured in terms of the Richter Scale. The latter term however presents a problem in that the author defines it as a particular sort of seismic event?viz: ?Rockburst? is understood as a seismic event that causes damage to an underground excavation with subsequent injury, loss of material/equipment or production shifts? (p. 322). No scale is given of the amount of: ?excavation damage ?level of injury ?material/equipment loss ?production shifts lost whether separate or cumulative, for a particular seismic event to be classified as a rockburst. A further difficulty arises in that in common usage the words ?rockburst?, ?seismic event? and ?earthquake? are all used to describe the same event.

Jan 1, 1999

By Frédéric Flament, Luc Lachance

"The important task of metallurgical accounting that used to be done manually is being more and more automated. Currently available solutions can generate accounting reports without human intervention or almost. However, the practical conditions for fully delivering the promised benefits of those solutions are sometimes overlooked either by end-users or by integrators. The mere fact of filling reports with values satisfying several constraints such as mass conservation constraints does not, by itself, ensure a high quality metallurgical balance. Since managers make decisions based on these reports, it is logical that the metallurgical balance performance be monitored and retrofits be made if necessary. Such retrofits may involve modifications to the measurement strategy or the reduction of the spatial resolution of the material balance model. This requires an estimability and redundancy analysis (ERA) tool to assess the feasibility of the modified model. Since determining by hand the estimability and redundancy of a set of non measured and measured variables is not trivial, even for a medium-sized mineral processing plant, a dedicated ERA tool brings valuable assistance to the metallurgist in charge. The present paper aims first at explaining how a state of the art metallurgical balance is a key enabler for the adoption of a smart process plants paradigm (SPPP) in mineral processing. Then, the fundamentals behind the building of an ERA algorithm are introduced and illustrated by two examples. Finally, the role of an ERA tool in achieving state of the art metallurgical accounting and how it contributes to delivering additional value are discussed.INTRODUCTIONThe Smart Process Plants Paradigm (SPPP)Mineral processors have seen an increase lately in external pressures toward operating performance improvements. Indeed, the globalization of the mining business is a key driver to becoming more productive, more responsive to market changes, to improving corporate governance and reporting standards. Furthermore, mineral processors are also expected by their neighbouring communities to continuously improve their sustainability score. These current pressures differ somewhat from the past ones in leading to a larger than ever number of conflicting constraints that plant managers must concurrently satisfy while maximizing plant profitability. It is in turn not surprising that this context requires actions involving more real-time collaborative actions between more people in more places than ever before."

Jan 1, 2011

By Mary E. Cocklan-Vendl

Regulatory processes associated with development of major mining operations in Alaska and British columbia were evaluated using specific case studies. Included were one hard rock mine in Alaska (Red Dog Mine), one hard rock mine In British Columbia (Snip Mine), and one offshore gold dredging project in Alaska (WestGold SIMA). Based on a comparison of the three case studies, it became clear that the primary incentives for cost effective permitting are: 1) early and continuing coordination of proposed project plans, designs and schedules with key regulatory agencies and local area residents and 2) development of a sufficient level of baseline information on air quality, water quality, wetlands, endangered species, fish and wildlife, and socia-cultural conditions to support the required permit application. The U.S. permitting process worked in much the same way as the Canadian permitting process. Disincentives of mine permitting include high initial costs for baseline data gathering. However, a relatively high early investment resulted in more efficient permit acquisition and reduced long-term monitoring requirements. A common problem Identified was the inadequate supply of trained agency personnel with the requisite technical and permitting experience. This sometimes resulted in poor decisions and unnecessary changes in project plans and schedules.

Jan 1, 1993

By D. Wolfe, R. Cleminson

"The Aurora North mine has been operating for more than ten years, and is the source of over half of Syncrude’s bitumen production. The hydrotransport systems at Aurora experience high rates of wear, and mission lengths on current slurry pumps are nominally 1,500-2,000 hours. Recent work has enabled a better understanding of the significant adverse effect of large particle impingement damage to impeller vane leading edges - which is the known life determining issue for Aurora hydrotransport pumps. A new pump design has been developed and installed at Aurora, incorporating significantly increased impeller diameter and pumping vane lengths. The new pumps are expected to triple Aurora’s previous mission length for hydrotransport pumps. Part II of this paper will share actual hydraulic and wear performance observed in the first several months of operation, and draw comparisons relative to what was expected for these pumps in design / development.INTRODUCTION Slurry Pumps are Critical Equipment at Syncrude Slurry pumps are a key component in Syncrude’s operations. In a typical Aurora application, each 5000 HP pump stage helps move over 8,000 dry tonnes per hour of oil sand, plus an equal volume of process water that has been added to create the slurry. The average impeller life in oil sand hydrotransport service at Aurora has been nominally 1,500 to 2,000 hours, or 12 to 16 million tonnes of oil sand pumped. Generally, the slurry pump application at Aurora has proven very difficult to improve due to the unique combination of high sand abrasivity, 125 mm (5”) large particle top size (lumps), and high flow rate relative to basic pump size; a factor that results in unduly high impeller vane leading edge speeds for the service conditions."

Jan 1, 2014

The Bureau de Recherches Geologiques et Minieres (BRGM) (a French Government-sponsored geological and mining agency), through international experience gained over many years, has become very skilled in alluvial prospection, particularly for diamonds. The research laboratories within the BRGM have also been active in creating new mineral processing equipment, some of which is directly applicable to such prospection. One such development, the mobile prospection unit, is described and its application in mineral exploration is demonstrated by a consideration of the diamond search in Australia and the general exploration of the Massif Armoricain (France). Because this latter study was fundamental in the development of the concept of 'mineral-geochemistry', and its application in mineral exploration, it is also briefly described.

Jan 1, 1971

In ilmenite smelting, the FeO content of the feed material (nominally FeO.TiO2) is decreased by reduction with carbon. In a parallel reaction, a significant amount of the TiO2is reduced to Ti2O3.One of the striking features of these reactions is a consistent relationship between the extents of FeO and TiO2reduction; this relationship is independent of furnace size. It was recently proposed that this relationship follows from the solidification behaviour of the slag, where the final slag composition corresponds to the minimum melting point (?eutectic groove?) in the FeO-TiO2-Ti2O3phase system; the hypothesis is that solidification equilibrium with the freeze lining stabilizes the slag composition. If this is the case, the system of slag and freeze lining must be capable of correcting two types of disturbances: thermal and compositional. Thermal disturbances result from incorrect power input, for the feed rates of ilmenite and reductant. For example, excessive power input will tend to overheat the slag, causing the freeze lining to melt partially, establishing a new steady-state heat loss from the furnace. Compositional disturbances result from an incorrect reductant input for the given power and ilmenite input. In this work, the dynamic response of the slag and freeze lining to different inputs (flow rates of ilmenite and reductant, and power input) is modelled. The model is based on solidification equilibria, and quantified heat loss through the freeze lining. The conclusion is that the solidification equilibrium cannot constrain the composition to the eutectic groove for typical operating conditions. Keywords: ilmenite smelting, freeze lining, solidification, high-titanium slag

Jan 1, 2004

By J. E. Murphy

The u.s. Bureau of Mines investigated electrode designs for electrowinning lead metal from a LiCl-KCl-PbCI2 electrolyte at 4500 C. The major objective of this investigation was to decrease the energy requirement for lead electrowinning. Electrolysis was performed in a bench-scale cell using several graphite electrode assemblies. Such parameters as electrode spacing, current density, and chlorine gas removal from the anode were investigated in the bench-scale tests. An optimum electrode assembly, termed the sawtooth design, was scaled up and operated at 3,000 and 4,000 A. The sawtooth electrodes operating at 3,000 A produced lead for 0.66 kW·h/kg. The electrodes were constructed by cutting large triangular grooves in the electrode surfaces. The electrodes were placed together such that the triangular peaks of one electrode projected into the triangular valleys of the other electrode. Chlorine did not build up on the anode with the sawtooth electrodes.

Jan 1, 1991

By S Durucan, A Korre

The application of simple methods of statistical analysis, coupled with geostatistical analysis and geographic information systems, can only summarise and give an outline of the spatial distribution of the parameters measured. Spatial analysis of the components or factors calculated, through principal component analysis or factor analysis, allows assessment of the geographical distribution of the dominant processes contributing to soil composition and/or contamination. Neither of these tools, however, distinguishes between the different sources of pollution. The application of canonical correlation to the data, driven by expert appraisal of the potential pollution sources, allows their quantitative and spatial assessment while GIS provides the environment in which to organise and present the results. The methodology is illustrated by its application to soil-contamination data from the Lavrio area in Greece, where silver-bearing orebodies have been mined for more than 25 centuries

Jun 21, 1905

By Jeremy P. Doolan, Leigh B. Neindorf, Geoff W. Capes

The development and use of rock mass classification tools have been a key component for improving stope design over the past 4 years at the Xstrata Zinc George Fisher Mine in northern Queensland, Australia. In 2003, stope extraction data from 3 years of open-stope mining provided an excellent situation to review the assumptions in the feasibility study. Extracted stope profile information, drillhole geotechnical data, underground observations, and oral and written communication were used to develop a thorough stope reconciliation performance database. With-out collecting the back analysis data and presenting the data in a usable format, engineers are left to debate opinion instead of engineered judgment. This can lead to biased and uninformed design parameter choices with the potential to repeat poor design. This paper demonstrates some effective, practical examples of empirical data collection where rock mass classifications tools were developed and used to create improved confidence in predicting stope stability and failure profiles. The work contributed to design changes that resulted in a reduction in stope hangingwall dilution and an increase in head grade while continuing to ramp up production from 2003–2005.

Jan 5, 2007

By Dany Pelletier, Yeves Breau, Ahmed Bouajila, Claude Gagnon

"In flotation circuits, direct measurement of the volumetric flow rate delivered by electromagnetic flowmeters is often difficult to obtain particularly due to piping and flow constraints. However, on-line material balance calculation could offer a reliable alternative to flow rate sensing. This paper describes an on-line material balance software package as applied to a copper flotation circuit for mass flow rate estimation mainly based on the output of an x-ray fluorescence onstream analyser. Rule-based procedures for the management of the main calculation modules are designed and integrated to a Comdale expert system. Attempts to diagnose the flotation process from mass flow rate data are also discussed.INTRODUCTIONThe need for improved process diagnosis, control and optimisation has become more evident for the mineral processing industry in the last decade. Therefore, new process variables need to be inferred or measured particularly in highly multivariable processes such as flotation. This process is subject to a wide variety of disturbances mainly generated by frequent and sometimes abrupt changes in physical and chemical characteristics of the ore and due to some irregularities in manual process operating procedures.A flotation circuit scheme is always a complex network counting more than two dozens of slurry streams. Information about those streams (%solids, metal content analysis, and flow rates) are important for process diagnosis, performance evaluation control and optimization (1,3).On-line sensing instruments such as x-ray fluorescence (XRF) on-stream analysers (OSA), gamma density gauges and electromagnetic flowmeters have been developed for the measurement of those variables. Unlike the other variables, stream flow rates could be determined by different ways:"

Jan 1, 2000

By Rundqvist

The best method to minimise disturbances from traffic to the neighbourhood and in Urban is probably to go underground. For obvious reasons this will cause vibrations, noise and other environmental effects which need very strict regulations and quality assurance in order to complete the work successfully. One project is “Southern Link”, a part of a ring road system. The system of tunnels includes 16 kilometres of tunnels right beneath the south part of the city of Stockholm. At least 20.000 people will be or could be affected by different kinds of disturbances and pollution such as vibrations, noise, gas and groundwater. Another project is the “Arlanda Link”. A new railway with three stations has been built under the existing and running to Arlanda airport with its terminals. Authorities have carefully judged these projects, which cause complaints from neighbours due to disturbances. The blasting operations are professionally managed by the contractors and controlled by consultants to keep the regulations according to the Swedish standards, which are well described in the tender documents by risk analysis and technical descriptions. In spite of that, one conclusion is that it is not always possible to go underground without exceeding stipulated regulations with existing technique. Some of the regulations also double the cost of excavation

Jan 1, 2001

By Y. Guglielmi, V. Merrien-Soukatchoff, I. Kadiri

ABSTRACT: Hydraulic experiments have been conducted since 1997 within a small fractured calcareous rock mass in southeastern France, at a site called Coaraze. On this reduced-scale site closing a floodgate located on a downstream spring produces repeated hydraulic loadings. Simultaneous measurements of normal deformations and pressure in several joints have provided a better understanding of the hydromechanical behaviour of such a fractured rock mass. The present paper first describes both the site and conceptual interpretation of the measurements performed. We showed that accurate measurement reproduction requires incorporating certain features: a variable normal joint stiffness, the joint vicinity (through introducing a Z coefficient), and the initial stress state. The paper then develops an original analytical interpretation of the coupled pressure-displacement measurements carried out, which reveal the high level of measurement suitability to the non-linear behaviours examined. 2D modelling, using the discontinuous code (UDEC) was used to proceed with the calibration step. KEY WORDS: In situ test, methodology, hydromechanics, modelling, non linear behaviour ZUSAMMENFASSUNG : Hydromechanische Experimente werden seit 1997 in einer kleinen Kalksteinmasse, das sich im Südosten von Frankreich befindet durchgeführt. In diesem kleinen Standort, werden wiederholte Wasserdruck Erhöhungen durch das Schliessen eines Hahnes produziert. Gleichzeitiger Druck und normale Verformung Meßungen in mehreren Fugen haben erlaubt, das hydromechanische Verhalten einer solche gebrochene Felsenmasse besser zu verstehen. Der Artikel beschreibt zuerst den Standort und stellt die begrifflichen Interpretationen der Meßungen vor. Um die Meßungen gut zu reproduzieren ist es wesentlich, bestimmte Faktoren wie die veränderliche normale Steifheit der Fugen, die Nachbarschaft der Fugen (über einen Z-Koeffizient) und der Spannungstand zu berücksichtigen. Der Artikel erklärt die originale Methode für die Druck- und Verformungs-Meßungen Interpretation und zeigt die gute Korrelation der Meßungen mit dem nicht-linearen angenommen Verhaltens der Fugen. Die numerische 2D-Modellierung mit dem UDEC Software ist für die Verkeilung der Faktoren gebraucht worden. SCHLÜSSELWÖRTER: In-situ-test, Methodologie, Hydromechanik, Numerische Modellierung, nicht-lineares Verhalten RESUME : Des expérimentations hydromécaniques sont conduites depuis 1997 dans un petit massif calcaire fracturé situé dans le sud de la France. Dans ce site de taille réduite des mises en charge répétées sont produites par la fermeture d'une vanne située à l'aval du site. Des mesures simultanées de déformation normale et de pression dans plusieurs joints ont permis de mieux appréhender le comportement d'un tel massif fracturé. L'article décrit dans un premier temps le site et présente les interprétations conceptuelles des mesures. Pour bien reproduire les mesures, Il est essentiel de prendre en compte certains facteurs tels que la raideur normale variable du joint, le voisinage du joint (par l'intermédiaire d'un coefficient Z), l'état de contrainte initial. L'article précise la méthode originale d'interprétation des mesures pression-déplacements qui montre la bonne adéquation aux lois de comportement non linéaire proposées. La modélisation 2D, à l'aide d'un code discontinu (UDEC) a été employée pour le calage des facteurs. MOTS-CLEFS : In-situ, méthodologie, hydromécanique, modélisation, comportement non linéaire

Jan 1, 2003

By L. J. Prosser, A. T. Iannacchione

Unfortunately from 1991 through 1995, 44 miners were fatally injured in the stone industry. Of these 12 occurred at underground mines from a total work force of less than 2,000 miners. Nine of these 12 miners were fatally injured in falls of roof or rib. A safer environment for the miners can be achieved by evaluating the nature of the hazardous ground and by developing more efficient and effective ground control strategies. Roof and rib conditions in the underground stone industry were observed and assessed at 33 mines in Illinois, Indiana, Kentucky, Maryland, Missouri, Pennsylvania, and West Virginia [(Figure 1)]. Hazard assessment indicated that those ground failures occurring under moderate to substantial overburden (> 30 m [l00 ft]) were caused by stress concentrations and geologic structures. Ground failures near the surface are caused by solution (water) processes. Selection of the mining horizon and mine layout decisions tremendously influence ground stability.

Feb 24, 1997

By A. B. Hooker, L. C. IlsLey

"Observation of the use of trailing cables in ""mines shows that the chief limiting factor in the life of the cables and their safe use is the smashing or crushing of the cables in service, together with the effects of consequent splicing.Trailing cables are crushed when run over by cars, mining machines; and locomotives or when hit by falls of roof. Crushing damages the insulation and may cause failure at once or in later use. Failure may be either by short circuit between the conductors or by grounding to the track. The failure of a live cable causes electric arcs capable of igniting explosive mixtures of methane and air. Every cable failure in a gassy or dusty mine is, therefore, a real or potential hazard.Some mine operators do not allow the splicing of trailing cables for use in gassy mines, bet require that a damaged cable be immediately replaced and if repaired that it be used only in nongassy mines. Other operators allow the making of temporary splices to permit completion of the shift but require that such splices be remade and vulcanized before the cable is used again.Still other operators allow the continued use of temporary splices, which in general means that a cable is used until the splices give trouble in reeling, or overheat, or pull apart. Then the spliced sections are either cut out or the whole cable is replaced.Splices often determine the useful life of a cable. A splice poorly made may pull apart ueder mechanical strain and cause arcing that burn* the surrounding cable or ignites as or coal-dust. If it has lower conductivity a splice is the first part of the cable to heat; it may become so hot under load that it will burn apart and damage other parts of the cable, or, if it be a soldered splice, the solder may melt and allow parting of the cable. A poorly made splice often has insufficient insulation which may alloy short-circuiting between conductors or permit external contacts capable of giving an electric shock to one handling the cable. The splice is sometimes bulky from too much insulation and takes up too much room on the reel, causing uneven reeling; also by catching on the spooling device the oversized splice may receive expressive pulls and wear. Splicing is therefore a very important factor in the use of trailing cables."

Mar 1, 1932